SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A bibliography of approximately 25 papers is presented on the Electron Echo Experiments. The data analysis included an extensive study of the electron accelerator beam, detector data correlations with the electron beam injections, and the study of about 30 onboard detected echoes.
Here, solutions and minerals containing sulfate (SO 4 2- ), and Ca 2+ and Mg 2+ cations, are ubiquitous throughout the lithosphere and are significant components of seawater, thus presenting a prototypical system for the study of strong electrolytes and crystal nucleation mechanisms. However, despite their relative abundance, key questions remain unanswered about the most fundamental atomic-level steps of their mineralization pathways and aqueous dynamics. Here, we carry out enhanced sampling multi-level molecular dynamics (MD) embedded correlated wavefunction theory simulations to elucidate ion-pairing mechanisms for Mg–SO 4 and Ca–SO 4 in concentrated aqueous solution, accurately capturing effects arising from both structural dynamics and electron exchange–correlation. We predict contact-ion-pair formation to be barrierless and highly exoergic for Ca–SO 4 , in agreement with its minimal solubility, whereas for Mg–SO 4 , solvent-shared and contact ion pairs have similar free energies, qualitatively consistent with its higher solubility. Finally, we demonstrate that brief high-temperature pre-equilibration may be utilized to accelerate convergence of free energies in blue-moon-ensemble enhanced-sampling MD.
Electron beam-induced current (EBIC) imaging is a well-established scanning electron microscope (SEM) technique used to analyze the behavior of microelectronic devices including solar cells. Recently, the application of EBIC imaging in an aberration-corrected scanning transmission electron microscope (STEM) has been demonstrated and offers great potential for the in situ study of electronic materials, correlating charge transport properties to atomic structural and elemental information. Here, this work presents two ways to implement EBIC imaging in conventional SEM and STEM systems: one relying on the instrument's inherent scanning and imaging electronics and the other involving third-party systems usually available in electron microscopes. The implementation of lock-in EBIC in systems equipped with a fast beam blanker is also described. In addition, this work shows and discusses the different mechanisms at play in EBIC imaging and their dependence on beam energy, sample impedance, and electrical measurement configuration, providing researchers with the basic information needed to apply the technique to their research.
Spectroscopic constants and dissociation energies for the ground states of N2, O2, and F2 determined at the CAS SCF MRCI correlation level are in excellent agreement with experiment when very large primitive valence and polarization one-particle Gaussian basis sets are employed. The dissociation energy (De) for N2 is larger than experiment unless the 2s electrons are correlated. The basis set requirement for an accurate determination of De is found to increase with the degree of multiple-bond character in the molecule.
Broadband infrared limb emission at 4.3 microns is measured by the TIMED/SABER instrument. At night, these emission observations at E-region altitudes are used to derive the so called NO+(v) Volume Emission Rate (VER). NO+(v) VER can be derived by removing the background CO2(v3) 4.3 microns radiance contribution using SABER-based non-LTE radiation transfer models, and by performing a standard Abel inversion on the residual radiance. SABER observations show that NO+(v) VER is significantly enhanced during magnetic storms in accordance with increased ionization of the neutral atmosphere by auroral electron precipitation, followed by vibrational excitation of NO+ (i.e., NO+(v)) from fast exothermic ion-neutral reactions, and prompt infrared emission at 4.3 m. Due to charge neutrality, the NO+(v) VER enhancements are highly correlated with electron density enhancements, as observed for example by Incoherent Scatter Radar (ISR). In order to characterize the response of the storm-time E-region from both SABER and ISR measurements, a Storm/Quiet ratio (SQR) quantity is defined as a function of altitude. For SABER, the SQR is the ratio of the storm-to-quiet NO+(v) VER. SQR is the storm-to-quiet ratio of electron densities for ISR. In this work, we compare SABER and ISR SQR values between 100 to 120 km. Results indicate good agreement between these measurements. SQR values are intended to be used as a correction factor to be included in an empirical storm-time correction to the International Reference Ionosphere model at E-region altitudes.
Influence of correlations on dielectric behavior of electron gas - nonperturbative approach to many-fermion system
This paper reviews observations of interplanetary particle beams of the kind that frequently accompany a solar flare. It is shown that the most frequently observed beams are beams of electrons which are associated with radio bursts of type III, but occasionally with flares and X-ray bursts. Although the main features of these beams and their associated plasma waves and radio bursts are known, uncertainties remain in terms of the correlation between electron beams and filamentary structures, the relative importance of the quasi-linear and the nonlinear wave emissions as the dominant process, and the mechanism of conversion of some of the Langmuir wave energy into radio emissions. Other particle beams discussed are those composed of protons, neutrons, He ions, or heavy ions. While most of these beams originate from sun flares, the source of some of particle beams may be the earth, Jupiter, or other planets as well as comets.
A review of the most pertinent data on solar energetic particles is presented, and the implications of the data are discussed, taking into account radio emissions, hard X-rays, gamma rays, energy spectra and electron-proton correlations, chemical compositions, and isotopic and ionic compositions. The mechanisms of solar flare particle acceleration are considered along with solar flare particle spectra in interplanetary space. Attention is given to stochastic acceleration, shock acceleration, acceleration in direct electric fields, the mean free paths of solar electrons and protons in interplanetary space, and an illustration of the probable effect of adiabatic deceleration on the spectra of solar flare ions at the time of maximum.
Recent advances have enabled simultaneous H-alpha and X-ray observations with substantially improved spatial, spectral, and temporal resolution. In this paper a study is conducted of two events observed as part of a coordinated observing program between the Solar Maximum Mission and Sacramento Peak Observatory: the flares of 1456 UT, 7 May 1980 and 1522 UT, 24 June 1980. Using recently developed physical models of static flare chromospheres, and corresponding theoretical H-alpha line profiles, effects of intense nonthermal electron heating can be distinguished from those of high conduction and pressure from the overlying flare corona. Both flares show the signature of intense chromospheric heating by fast electrons, temporally correlated with X-ray light curves at E greater than 27keV, and spatially associated with X-ray emission sites at E greater than 16 keV. Interpreting the H-alpha line profile observations using the theoretical H-alpha line profiles, values of the thick-target input power contained in nonthermal electrons that are observationally indistinguishable (within a factor of 2-3) from those inferred from the X-ray data are inferred. Although these events are small, the energy flux values are large: of order 10 to the 11th ergs per sq cm per s above 20 keV.
Two different methods were applied to determine the cross-shock potential jump in the de Hoffmann-Teller reference frame, using a data set that represented 66 crossings of the terrestrial bow shock and 14 interplanetary shocks observed by various ISEE spacecraft, and one crossing each of the Jovian bow shock and the Uranian bow shock made by the Voyager spacecraft. Results for estimates of the electrostatic potential based on an estimate of the jump in electron enthalpy correlated well with estimates based on Liouville's theorem, although the Liouville-determined values were systematically the higher of the two, suggesting that significant irreversible processes contribute to the shape of the downstream distribution. The potential jump corresponds to approximately 12-15 percent of the incident ion ram kinetic energy, and was found not to be controlled by the Mach number, plasma beta, shock geometry, or electron to ion temperature ratios.
Creep strength-enhanced ferritic (CSEF) steels such as Grade 91 (9Cr-1Mo-V) and Grade 92 (Fe-9Cr-2W-0.5Mo) steels are widely used in the fossil-fuel-fired and nuclear power plants. The weld integrity of these steels is crucial for power plants' safe and reliable operations. Due to harsh service conditions, the steel weld can become susceptible to environmental degradation. Field welding repair is used to restore the degraded weld’s performance where a controlled temper-bead welding technique is commonly used to temper the freshly formed martensite during welding. However, knowledge of weld repairability is limited and experimental trial and error optimization to achieve desired microstructure and joint properties is expensive and time-consuming. Many existing computational models, e.g., finite element models, are limited to solving heat conduction equation and ignoring convective heat transfer due to molten metal flow. These models can result in over-prediction of peak temperatures of weld pool and heat-affected zone (HAZ), which in turn can affect the accuracy of tempering prediction. Moreover, these finite element models require an input of the deposit profiles in advance and thus limits the usability of these models. Here, a molten pool-based, multi-pass multi-layer model has been developed based on computational fluid dynamics (CFD) approach with the Volume of Fluid (VOF) method. The model calculates the bead formation, thereby eliminating the need for pre-determined bead profiles required by finite element models. For computational efficiency, a coordinate system attached to the moving heat source is utilized. A subroutine is developed to convert the temperature profiles in the reference frame stationary to the heat source to that stationary to the workpiece. The converted thermal cycles are then imported into a microstructure model to compute the tempering kinetics and resultant hardness using a Johnson-Mehl-Avrami-Kolmogorov (JMAK), and modified Grange-Baughman parameter. The modeling approach is first developed and validated on single- and multi-pass deposition of stainless steel filler metal onto a SA-533 high strength steel substrate. The models are then applied to a multi-pass V-groove repair weld of Grade 91 steel plate as well as directed energy deposition of Grade 92 steel. Non-destructive characterization of microstructures was performed on Grade 91 and 92 steel welds. Two welding processes, cold metal transfer (CMT) and flux-cored arc welding (FCAW), were investigated for the Grade 91 steel weld samples. For the Grade 92 weld samples, three different heat inputs (low, medium, and high) of gas tungsten arc welding (GTAW) were utilized to replicate traditional field welding processes. The non-destructive evaluation (NDE) method used for this research was immersion ultrasonic testing (UT) using a micro-resolution ultrasonic imaging methodology specifically designed to operate in the through-transmission configuration operating at 20 MHz of frequency. The system used a focused ultrasonic beam spot size diameter between 250-300 μm, and a 6 μm laser vibrometer spot size for detection, to produce highly defined images with longitudinal and mode-converted shear waves. From the micro-resolution ultrasonic C-scan images, three microstructural regions, i.e., weld metal (WM), HAZ, and base metal (BM), were clearly identifiable. Various levels of ultrasonic amplitudes distributed over the three regions were correlated with electron beam backscattered diffraction (EBSD) images using grain size, grain boundaries, and dislocation densities. The results showed that areas with relatively higher ultrasonic amplitude levels were associated with smaller grains and higher dislocation densities, while areas with lower amplitude levels were associated with larger grains and lower dislocation densities. In addition, ultrasonic velocity data obtained across the three different weld microstructural regions of Grade 91 test samples were correlated with optical metallographic images and hardness measurements. The results showed distinctive decreases in ultrasonic velocity and hardness over the HAZ region, where weld failures often occur during service.
We report an investigation of the effect of substitution of Y for Tm in Tm 1-x Y x VO 4 via low-temperature heat capacity measurements, with the yttrium content x varying from 0 to 0.997. Because the Tm ions support a local quadrupolar (nematic) moment, they act as reporters of the local strain state in the material, with the splitting of the ion's non-Kramers crystal field ground state proportional to the quadrature sum of the in-plane tetragonal symmetry-breaking transverse and longitudinal strains experienced by each ion individually. Analysis of the heat capacity, therefore, provides detailed insights into the distribution of local strains that arise as a consequence of the chemical substitution. These local strains suppress long-range quadrupole order for x > 0.22, and result in a broad Schottky-like feature for higher concentrations. Heat capacity data are compared to expectations for a distribution of uncorrelated (random) strains. For dilute Tm concentrations, the heat capacity cannot be accounted for by randomly distributed strains, demonstrating the presence of significant strain correlations between sites. For intermediate Tm concentrations, these correlations must still exist, but the data cannot be distinguished from that which would be obtained from a two-dimensional Gaussian distribution. The crossover between these limits is discussed in terms of the interplay of key lengthscales in the substituted material. Furthermore, the central result of this work, namely that local strains arising from chemical substitution are not uncorrelated, has implications for the range of validity of theoretical models based on random effective fields that are used to describe such chemically substituted materials, particularly when electronic nematic correlations are present.
The solar seeing image motion has been monitored electronically and absolutely with a 25 cm telescope at three sites along the ridge at the southern end of the Magdalena Mountains west of Socorro, New Mexico. The uncorrelated component of the variations of the optical flux from two points at opposite limbs of the solar disk was continually monitored in 3 frequencies centered at 0.3, 3 and 30 Hz. The frequency band of maximum signal centered at 3 Hz showed the average absolute value of image motion to be somewhat less than 2sec. The observer estimates of combined blurring and image motion were well correlated with electronically measured image motion, but the observer estimates gave a factor 2 larger value.
Lack of instrument sensitivity to low electron density (Ne) concentration makes it difficult to measure sharp Ne vertical gradients (four orders of magnitude over 30 km) in the D/E-region. A robust algorithm is developed to retrieve global D/E-region Ne from the high-rate GNSS radio occultation (RO) data, to improve spatio-temporal coverage using recent SmallSat/CubeSat constellations.The new algorithm removes F-region contributions in the RO excess phase profile by fitting a linear function to the data below the D-region.The new GNSS-RO observations reveal many interesting features in the diurnal, seasonal, solar-cycle, and magnetic-field-dependent variations in the Ne morphology. While the D/E-region Ne is a function of solar zenith angle (c), it exhibits strong latitudinal variations for the same c with a distribution asymmetric about noon. In addition, large longitudinal variations are observed along the same magnetic field pitch angle. The summer-midlatitude Ne and sporadic-E(Es) show a distribution similar to each other. The distribution of auroral electron precipitation correlates better with the pitch angle from the magnetosphere than from one at100 km. Finally, anew TEC retrieval technique is developed for the high-rate RO data with a top reaching at least 120 km. For better characterization of the E-to-F transition in Ne and more accurate TEC retrievals, it is recommended to have all GNSS-RO acquisition routinely up to 220 km.
The potential for extracellular electron transfer (EET) is a prevailing genomic feature of humic lake bacterioplankton. However, there has been little evidence for the substantial ecological contribution predicted by genetics. We hypothesized that anoxygenic phototrophic electrotrophs and accompanying heterotrophic electrogens cycle dissolved organic matter (DOM) between oxidized and reduced states. We predicted that such bacterioplankton would exhibit diel-scale oscillations due to the light dependency of photosynthesis. Using Trout Bog Lake in Wisconsin, USA, as our model ecosystem, we profiled the water column with depth-discrete metagenomic, physiochemical, and electrochemical analyses. We observed variation in oxidation reduction potential (ORP) in response to sunlight, initiating at depths populated by anoxygenic phototrophs with EET genes. We developed an automated buoy to measure electric current flow between many pairs of electrodes simultaneously, observing correlation in electron consumption to sunlight. Our results, combined with published metatranscriptomic analysis, indicate the occurrence of electron cycling between phototrophic oxidation (electrotrophic metabolism) by Chlorobium and anaerobic respiration (electrogenic metabolism) by Geothrix, involving DOM. We also repeatedly observed gradual seasonal increases in hypolimnion ORP throughout summer. These diel and seasonal patterns imply that electroactive DOM mediates the ecology of electroactive bacteria in lakes, controlling humic lake methane emissions.IMPORTANCEWe investigated the physical, chemical, and redox characteristics of a bog lake and electrodes hung therein to test the hypothesis that dissolved organic matter is being cycled between oxidized and reduced states by electroactive bacterioplankton powered by phototrophy. To do so, we performed field-based analyses on multiple timescales using both established and novel instrumentation. We paired these analyses with recently developed bioinformatics pipelines for metagenomics data to investigate genes that enable electroactive metabolism and accompanying metabolisms. Our results are consistent with our hypothesis and yet upend some of our other expectations. Our findings have implications for understanding greenhouse gas emissions from lakes, including electroactivity as an integral part of lake metabolism throughout more of the anoxic parts of lakes and for a longer portion of the summer than expected. Our results also give a sense of what electroactivity occurs at given depths and provide a strong basis for future studies.
We present a real-space method for computing the random phase approximation (RPA) correlation energy within Kohn–Sham density functional theory, leveraging the low-rank nature of the frequency-dependent density response operator. In particular, we employ a cubic-scaling formalism based on density functional perturbation theory that circumvents the calculation of the response function matrix, instead relying on the ability to compute its product with a vector through the solution of the associated Sternheimer linear systems. We develop a large-scale parallel implementation of this formalism using the subspace iteration method in conjunction with the spectral quadrature method while employing the Kronecker product-based method for the application of the Coulomb operator and the conjugate orthogonal conjugate gradient method for the solution of the linear systems. We demonstrate convergence with respect to key parameters and verify the method’s accuracy by comparing with plane-wave results. We show that the framework achieves good strong scaling to many thousands of processors, reducing the time to solution for a lithium hydride system with 128 electrons to around 150 s on 4608 processors.
While multiconfigurational approaches have long been relegated to expert practitioners working on a case-by-case basis, recent developments have increasingly made these methods more routine and applicable to broader sets of systems. This article outlines the state-of-the-art in multiconfigurational approaches, with an emphasis on moving from delicate hand-selected pathways through configuration space toward more robust and efficient approaches to treating a host of challenging chemical systems accurately. First, we overview recent work in automated active-space selection, which has enabled increasingly large-scale applications of multireference methods to modeling vertical excitations and reactivity. Second, we highlight the increasingly efficient methods for recovering correlation energy beyond the active space, as headlined by extensions of pair-density functional theory and its role in accurate and efficient treatment of excited-state dynamics and its utilization to train machine-learned potentials. Finally, we highlight recent efforts to treat extended systems that until recently have lied beyond the traditional limits of active-space methods, giving center stage to product-form wave functions of the localized active space family of methods that allow for the computation of multiconfigurational band structures. These recent advancements point to a broader use of multireference approaches for high-impact chemical and materials science applications.
Ultra-high-molecular-weight (UHMW, >106 Da) polymers have unique thermomechanical properties due to their large number of physical entanglements. Producing UHMW styrenic polymers is challenging because of their prohibitively slow homopolymerization kinetics. In this report, we show that alternating photoiniferter copolymerization between methoxy-functionalized styrenic monomers and pentafluorostyrene can circumvent this limitation under conditions where arene–perfluoroarene (AP) interactions contribute to favorable monomer association and accelerate copolymerization. Increasing methoxy substitution on the styrene arene ring leads to pronounced rate enhancements that correlate with electronic complementarity between the styrenic comonomers. Density functional theory calculations reveal increasingly favorable AP interaction energies across the series, consistent with monomer association contributing to faster propagation. The result is up to 2000% enhancement in propagation rate in copolymerizations compared to styrene homopolymerization. Despite these rate enhancements, the resulting materials retain broadly similar glass-transition temperatures and network-like thermomechanical behavior, with only modest softening across the series. Here, we then leverage the approach to produce UHMW trialkoxystyrene copolymers bearing sterically encumbered pendants, which are ultrasoft (Young's modulus of 8 kPa) and highly extensible (560%). These results establish that designed supramolecular association between styrenics is a powerful tool for controlling reactivity in radical polymerization and generating otherwise difficult-to-obtain materials.