SEARCH · Search NASA

Results for “experimental data analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Performance and load data from Mod-0A and Mod-1 wind turbine generators

Experimental data, together with supporting analysis, are presented on the power conversion performance and blade loading of large, horizontal-axis wind turbines tested at electric utility sites in the U.S. Four turbine rotor configurations, from 28 to 61 meters in diameter, and data from five test sites are included. Performance data are presented in the form of graphs of power and system efficiency versus free-stream wind speed. Deviations from theoretical performance are analyzed statistically. Power conversion efficiency averaged 0.34 for all tests combined, compared with 0.31 predicted. Round blade tips appeared to improve performance significantly. Cyclic blade loads were normalized to develop load factors which can be used in the design of rotors with rigid hubs.

Spera, D. A.↗

NASA NTRS1983

Thermomechanical loading of multilayered cylindrical geometries in thermal cycling from 300 to 1300 K

The principal of multiple material layering is well known as an effective method of reducing heat transfer; however, thermal gradients can impose significant loads and lead to delamination and subsequent component failure. An analysis is developed and experimental data are discussed for the thermomechanical effects of multilayered materials on a heat sink substrate of cylindrical geometry subject to thermal cycling. The geometry is heated in cross-flow by a high-velocity flame and cooled in crossflow by ambient-temperature air from a critical flow orifice. Each layer of material possesses a threshold beyond which small changes in temperature or mechanical loading greatly influence the life in thermal cycling of the layered materials. Comparisons are made between the thermomechanical loads predicted by various numerical codes for the linear case and by a simplified analytic model.

Hendricks, R. C.↗

NASA NTRS1983

Analytical prediction of aerothermal environment in a wing-elevon cove

The fluid/thermal environment in the cove between the wing and elevon surfaces was a concern throughout the design and initial operational phases of the space shuttle. Experimenal and analytical investigations provided some understanding of the environmental in the wing-elevon cove. An incompressible finite element analysis of flow through straight parallel walls and curved parallel walls to determine the effects of cove geomtry on the fluid/thermal environment is described. Results from this analysis agree qualitatively with experimental data. The centerline gas temperatures and cold wall heating rates are virtually identical for the two cases indicating that the slight curvature has little effect on the overall thermal environment.

Bey, K. S.↗

NASA NTRS1984

The role of airfoil geometry in minimizing the effect of insect contamination of laminar flow sections

A method has been developed to predict the contamination of an airfoil by insects and the resultant performance penalty. Insect aerodynamics have been modeled and the impingement of insects on an airfoil are solved by calculating their trajectories. Upon impact, insect rupture and the resulting height of the debris is determined based on experimental data. A boundary layer analysis is performed to determine which insects cause boundary layer transition and the resultant drag penalty. A contaminated airfoil figure of merit is presented to be used to compare airfoil susceptibility. Results show that the insect contamination effects depend on accretion conditions, airfoil angle of attack and Reynolds number. The importance of the stagnation region to designing airfoils for minimum drag penalties is discussed.

Maresh, J. L.↗

NASA NTRS1985

Three-dimensional inviscid analysis of radial turbine flow and a limited comparison with experimental data

The three-dimensional inviscid DENTON code is used to analyze flow through a radial-inflow turbine rotor. Experimental data from the rotor are compared with analytical results obtained by using the code. The experimental data available for comparison are the radial distributions of circumferentially averaged values of absolute flow angle and total pressure downstream of the rotor exit. The computed rotor-exit flow angles are generally underturned relative to the experimental values, which reflect the boundary-layer separation at the trailing edge and the development of wakes downstream of the rotor. The experimental rotor is designed for a higher-than-optimum work factor of 1.126 resulting in a nonoptimum positive incidence and causing a region of rapid flow adjustment and large velocity gradients. For this experimental rotor, the computed radial distribution of rotor-exit to turbine-inlet total pressure ratios are underpredicted due to the errors in the finite-difference approximations in the regions of rapid flow adjustment, and due to using the relatively coarser grids in the middle of the blade region where the flow passage is highly three-dimensional. Additional results obtained from the three-dimensional inviscid computation are also presented, but without comparison due to the lack of experimental data. These include quasi-secondary velocity vectors on cross-channel surfaces, velocity components on the meridional and blade-to-blade surfaces, and blade surface loading diagrams. Computed results show the evolution of a passage vortex and large streamline deviations from the computational streamwise grid lines. Experience gained from applying the code to a radial turbine geometry is also discussed.

Choo, Y. K.↗

NASA NTRS1990

Towards a methodology for robust parameter identification

Consideration is given to the problem of estimating, from experimental data, real parameters for a model with uncertainty in the form of both additive noise and norm-bounded perturbations. Such models frequently arise in robust control theory, and a framework is introduced for the consideration of experimental data in robust control analysis problems. If the analysis tools applied include robust stability tests for real parameter variations (real mu), the framework can be used to address the problem of robust parameter identification. While the techniques discussed can quickly become computationally overwhelming when applied to physical systems and real data, the approach introduces a novel way of looking at the identification problem and may be helpful in arriving at a more tractable methodology.

Smith, Roy S.↗

NASA NTRS1991

Water droplet impingement on airfoils and aircraft engine inlets for icing analysis

This paper includes the results of a significant research program for verification of computer trajectory codes used in aircraft icing analysis. Experimental water droplet impingement data have been obtained in the NASA Lewis Research Center Icing Research Tunnel for a wide range of aircraft geometries and test conditions. The body whose impingement characteristics are required is covered at strategic locations by thin strips of moisture absorbing (blotter) paper and then exposed to an airstream containing a dyed-water spray cloud. Water droplet impingement data are extracted from the dyed blotter strips by measuring the optical reflectance of the dye deposit on the strips with an automated reflectometer. Impingement characteristics for all test geometries have also been calculated using two recently developed trajectory computer codes. Good agreement is obtained with experimental data. The experimental and analytical data show that maximum impingement efficiency and impingement limits increase with mean volumetric diameter for all geometries tested. For all inlet geometries tested, as the inlet mass flow is reduced, the maximum impingement efficiency is reduced and the location of the maximum impingement shifts toward the inlet inner cowl.

Papadakis, Michael↗

NASA NTRS1991

Aerodynamic sensitivity analysis methods for the compressible Euler equations

This study presents a mathematical formulation developed for aerodynamic sensitivity coefficients based on a discretized form of the compressible 2D Euler equations. A brief motivating introduction to the aerodynamic sensitivity analysis and the reasons behind an integrated flow/sensitivity analysis for design algorithms are presented. The finite difference approach and the quasi-analytical approach are used to determine the aerodynamic sensitivity coefficients. A new flow prediction concept, which is an outcome of the direct method in the quasi-analytical approach, is developed and illustrated with an example. Surface pressure coefficient distributions of a nozzle-afterbody configuration obtained from the predicted flowfield solution are compared successfully with their corresponding values obtained from a flowfield analysis code and the experimental data.

Baysal, Oktay↗

NASA NTRS1990

Effect of microstructure on the response of composite tubes

This paper addresses the effects of changes in the fiber content in the individual layers of a composite tube and the presence of resin-rich interplay regions on the torsional response of the tube. A micromechanics-based procedure is outlined to correct the properties of unidirectional graphite/epoxy obtained from flat coupon tests in order to account for the lower fiber volume fraction in the individual layers of a composite tube made from the same material. The corrected properties are used as input parameters to an analytical model developed to predict the response of composite tubes subjected to combined axial/torsion loading. It is illustrated that when the corrected properties and the resin-rich regions are included in the analysis, good correlation with experimental data is obtained.

Derstine, M. S.↗

NASA NTRS1992

Design and analysis of filament-wound cylinders in compression

The objective of the study was to develop a more accurate model for the prediction of the compressive behavior of filament-wound composite cylindrical shells. Results from a closed-form analytical model and a three-dimensional finite element model show that the extensional and bending stiffness of the laminate is significantly reduced in tow cross-over regions and that bending-extension coupling is increased in comparison with classical lamination theory. The material properties predicted by a micromechanics analysis are included in a global finite element model of a filament-wound circular cylindrical shell which also incorporates variations in the laminate stacking thickness. Results from the global shell analysis are compared with experimental data.

Hipp, Patrick A.↗

NASA NTRS1992

High repetition-rate Q-switched and intracavity doubled diode-pumped Nd:YAG laser

A Nd:YAG laser was end pumped with 2.2 W of continuous-wave (CW) diode laser output. Efficient operation of the laser at high repetition rates was emphasized. This laser provides 890 mW of TEM00 CW output at 1064 nm, and 340 mW of 532 nm average power at a Q-switched repetition rate of 25 kHz. Experimental data are compared with analysis.

Hemmati, Hamid↗

NASA NTRS1992

Fracture toughness testing of polymer matrix composites

The experimental techniques and associated data analysis methods used to measure the resistance to interlaminar fracture, or 'fracture toughness', of polymer matrix composite materials are described. A review in the use of energy techniques to characterize fracture behavior in elastic solids is given. An overview is presented of the types of approaches employed in the design of delamination-resistant composite materials.

Grady, Joseph E.↗

NASA NTRS1992

Studies of radiative emission from the simulated shock layer of the Huygens probe

An investigation has been conducted to determine the radiative heating of the Huygens probe. The shock tube facility at Stanford University was used to generate plasma behind strong shocks, which simulates the flow field around the probe. Spectroscopic techniques have been used to measure thermophysical quantities of the plasma in the shock tube. A numerical code has been developed using a three temperature model in order to generate one dimensional flow field solutions for comparison with these experimental data. Based on this analysis, the radiative heat transfer at the stagnation point of the prove was approximated.

Park, C. S.↗

NASA NTRS1993

Low-Reynolds-number k-epsilon model for unsteady turbulent boundary-layer flows

An assessment of the near-wall and low-Reynolds-number functions used in low-Reynolds-number k-epsilon models suggests that they are not suitable for the near-wall region of unsteady turbulent boundary layers, where the flow is characterized by rapid changes in phase. An improved low-Reynolds-number k-epsilon model is developed in this paper. The near-wall and low-Reynolds-number functions in this model are formulated as functions of the local turbulent Reynolds numbers instead of the inner variable y(+). The present model also has the correct asymptotic behavior in the near-wall region. The turbulence model has been incorporated in an unsteady boundary-layer code and validated for unsteady turbulent boundary layers with and without adverse pressure gradients. The predictions agree well with the experimental data and the theoretical analysis. For the cases tested, the present model correctly predicts the unsteady near-wall flow and the unsteady shin friction at various frequencies.

Fan, Sixin↗

NASA NTRS1996

Comparison of Fire Model Predictions with Experiments Conducted in a Hangar With a 15 Meter Ceiling

The purpose of this study is to examine the predictive capabilities of fire models using the results of a series of fire experiments conducted in an aircraft hangar with a ceiling height of about 15 m. This study is designed to investigate model applicability at a ceiling height where only a limited amount of experimental data is available. This analysis deals primarily with temperature comparisons as a function of distance from the fire center and depth beneath the ceiling. Only limited velocity measurements in the ceiling jet were available but these are also compared with those models with a velocity predictive capability.

MATHEMATICAL MODELS↗

NASA NTRS1998

Heat Transfer on a Film-Cooled Blade - Effect of Hole Physics

A multi-block, three-dimensional Navier-Stokes code has been used to study the within-hole and near-hole physics in relation to heat transfer on a film-cooled blade. The flow domain consists of the coolant flow through the plenum and hole-pipes for the three staggered rows of shower-head holes on the VK1 rotor, and the main flow over the blade. A multi-block grid is generated that is nearly orthogonal to the various surfaces. It may be noted that for the VK1 rotor the shower-head holes are inclined at 30 deg. to the spanwise direction, and are normal to the streamwise direction on the blade. Wilcox's k-omega turbulence model is used. The present study provides a much better comparison for the heat transfer coefficient at the blade mid-span with the experimental data than an earlier analysis wherein coolant velocity and temperature distributions were specified at the hole exits rather than extending the computational domain into the hole-pipe and plenum. Details of the distributions of coolant velocity, temperature, k and omega at the hole exits are also presented.

Garg, Vijay K.↗

NASA NTRS1999

Heat Transfer on a Film-Cooled Blade: Effect of Hole Physics

A multiblock, three-dimensional Navier Stokes code has been used to study the within-hole and near-hole physics in relation to heat transfer on a film-cooled blade. The flow domain consists of the coolant flow through the plenum and hole-pipes for the three staggered rows of shower-head holes on the VKI rotor, and the main flow over the blade. A multiblock grid is generated that is nearly orthogonal to the various surfaces. It may be noted that for the VKI rotor the shower-head holes are inclined at 30 deg to the spanwise direction, and are normal to the streamwise direction on the blade. Wilcox's k-omega turbulence model is used. The present study provides a much better comparison for the span-averaged heat transfer coefficient on the blade surface with the experimental data than an earlier analysis wherein coolant velocity and temperature distributions were specified at the hole exits rather than extending the computational domain into the hole-pipe and plenum. Details of the distributions of coolant velocity, temperature, k and omega at the hole exits are also presented.

Garg, Vijay K.↗

NASA NTRS2003

Infrared Thermography Flight Experimentation

Analysis was done on IR data collected by DFRC on May 8, 2002. This includes the generation of a movie to initially examine the IR flight data. The production of the movie was challenged by the volume of data that needed to be processed, namely 40,500 images with each image (256 x 252) containing over 264 million points (pixel depth 4096). It was also observed during the initial analysis that the RTD surface coating has a different emissivity than the surroundings. This fact added unexpected complexity in obtaining a correlation between RTD data and IR data. A scheme was devised to generate IR data near the RTD location which is not affected by the surface coating This scheme is valid as long as the surface temperature as measured does not change too much over a few pixel distances from the RTD location. After obtaining IR data near the RTD location, it is possible to make a direct comparison with the temperature as measured during the flight after adjusting for the camera s auto scaling. The IR data seems to correlate well to the flight temperature data at three of the four RID locations. The maximum count intensity occurs closely to the maximum temperature as measured during flight. At one location (RTD #3), there is poor correlation and this must be investigated before any further progress is possible. However, with successful comparisons at three locations, it seems there is great potential to be able to find a calibration curve for the data. Moreover, as such it will be possible to measure temperature directly from the IR data in the near future.

Blanchard, Robert C.↗