Search NASA⌕ Search

SEARCH · Search NASA

Results for “fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Direct-write laser-assisted patterning of form birefringence in wave plates fabricated by glancing-angle deposition

The development of optics that provide spatial control of birefringence could enable better control of laser beam polarization, but available solutions are limited. Here we demonstrate a method to locally modify the birefringence of wave plates fabricated by glancing-angle deposition. The method employs localized melting of the anisotropic microstructure in a vacuum environment to alter the local birefringence. We demonstrate that this process is only possible under high vacuum to avoid trapping air within the melt zone. The direct-write method presented here can be readily utilized for coatings exhibiting form birefringence of virtually any chemical composition, size, and format.

42 ENGINEERING↗
DOE OSTI2024

Low loss fiber-coupled volumetric interconnects fabricated via direct laser writing

Photonic integrated circuits (PICs) are vital for high-speed data transmission. However, optical routing is limited in PICs composed of only one or a few stacked planes. Further, coupling losses must be low in deployed systems. Previously, we developed the subsurface controllable refractive index via beam exposure (SCRIBE) technique to write accurate 3D gradient refractive index (GRIN) profiles within a mesoporous silica scaffold. Here, we apply SCRIBE to fabricate low loss, broadband, polarization insensitive, fiber-coupled, single-mode volumetric interconnects that include waveguides traversing arbitrary 3D paths. By seamlessly integrating mode-matching subsurface lenses and GRIN waveguide tapers, calibrating for positional writing errors, implementing multipass exposure, automating alignment, and switching to antireflection coated fibers, we reduced the insertion loss for a fiber-PIC-fiber interconnect from 50 to 2.14 dB, or 1.47 dB, excluding the fiber array’s loss. Further, we establish an upper bound of 0.45 dB loss per coupler. We report quality factors of 27,000 and 77,000 and bending losses of 6 and 3 dB/cm for 15 and 30 µm radii microrings, respectively. We also demonstrate Bézier escalators, polarization-rotating and polarization-splitting interconnects, and a seven-channel 25 µm pitch volumetric interconnect. The SCRIBE platform presents a clear path toward realizing 3D PICs with unique functionality.

Optics↗
DOE OSTI2022

Deep learning for electron and scanning probe microscopy: From materials design to atomic fabrication

Machine learning and artificial intelligence (ML/AI) are rapidly becoming an indispensable part of physics research, with applications ranging from theory and materials prediction to high-throughput data analysis. In parallel, the recent successes in applying ML/AI methods for autonomous systems from robotics through self-driving cars to organic and inorganic synthesis are generating enthusiasm for the potential of these techniques to enable automated and autonomous experiment in imaging. Here, we discuss recent progress in application of machine learning methods in scanning transmission electron microscopy and scanning probe microscopy, from applications such as data compression and exploratory data analysis to physics learning to atomic fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fabrication and Tuning of a THz-Driven Electron Gun

We have developed a THz-driven field emission electron gun and beam characterization assembly. The two cell standing-wave gun operates in the pi mode at 110.08 GHz. It is designed to produce 360 keV electrons with 500 kW of input power supplied by a 110 GHz gyrotron. Multiple gun structures were electroformed in copper using a high precision diamond-turned mandrel. The field emission cathode is a rounded copper tip located in the first cell. The cavity resonances were mechanically tuned using azimuthal compression. This work will discuss details of the fabrication and tuning and present the results of low power measurements.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

EVALUATION OF FLUX EXPULSION AND FLUX TRAPPING SENSITIVITY OF SRF CAVITIES FABRICATED FROM COLDWORK NB SHEET WITH SUCCESSIVE HEAT TREATMENT

The main source of RF losses leading to lower quality factor of SRF cavities is due to the residual magnetic flux trapped during cooldown. The loss due to flux trapping is more pronounced for cavities subjected to impurities doping. The flux trapping and its sensitivity to rf losses are related to several intrinsic and extrinsic phenomena. To elucidate the effect of recrystallization by high temperature heat treatment on the flux trapping sensitivity, we have fabricated two 1.3 GHz single cell cavities from cold-worked Nb sheets and compared with cavities made from standard fine-grain Nb. Flux expulsion ratio and flux trapping sensitivity were measured after successive high temperature heat treatments as well as after low temperature, 120 0C baking. The cavity made from cold worked Nb showed better performance after 800 0C/3hr heat treatment and similar behavior when heat treated with additional 900 0C and 1000 0C compared to standard fine-grain Nb cavity. In this contribution, we present the summary of flux expulsion, trapping sensitivity and results from RF tests at 2 K.

Khanal, Bashu↗
DOE OSTI2023

Fabrication and Testing of a Prototype RF-Dipole Crabbing Cavity

Crabbing cavities are essential in particle colliders to compensate the luminosity degradation due to beam collision at a crossing angle. The 952.6 MHz 2-cell rf-dipole crabbing cavity system was proposed for the Jef-ferson Lab Electron-Ion Collider to restore the head-on collisions of electron and proton bunches at the interac-tion point. A prototype cavity was designed and devel-oped to demonstrate the performance of multi-cell rf-dipole structures. This paper presents the fabrication pro-cess and cold test results of the first 2-cell rf-dipole proto-type cavity.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Update of ASHRAE Standard 140 Section 5.2 and Related Sections (BESTEST Building Thermal Fabric Test Cases)

This report documents new work intended to update the current building thermal fabric software-to-software comparative test specifications and example results of ANSI/ASHRAE Standard 140-2017, Sections 5.2.1, 5.2.2, 5.2.3, and related supporting sections. The Building Energy Simulation Test and Diagnostic Method (BESTEST) test specification and example results that provide the basis for these Standard 140 sections were originally published in 1995. The state of the art in building energy simulation modeling has advanced since then. Additionally, comments on the test specification over the years highlighted ambiguities, further necessitating the update to the original work. This new work was conducted for the U.S. Department of Energy (DOE) by Argonne National Laboratory (Argonne) and National Renewable Energy Laboratory (NREL), in collaboration with a working group of international experts associated with the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) Standing Standard Project Committee (SSPC) 140. SSPC 140 is responsible for ANSI/ASHRAE Standard 140. The new work, presented in this report, defined the test cases and specifications such that building energy simulation programs with time steps of one hour or less can perform the tests. Revisions to the test specification and update of example results follow the vetting process of iterative field trials established for previous BESTEST work that has been adapted for ASHRAE Standard 140.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Fabricating and Testing Additively Manufactured Components for Tritium Service Consideration

This SRTE PDRD sponsored project produced test articles, tooling, and training articles for evaluation. In addition, the hydrogen compatibility of the alloys that can be readily produced by the Arcam A2X was tested. During the evaluation it was determined that the mechanical properties were more sensitive to build plate location than hydrogen exposure. Hydrogen pressure – volume-temperature experiments showed that the as-fabricated samples did not absorb hydrogen readily, but activated samples did.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Integrating Applied Energy and BER Smart Data Capabilities to Develop a DOE Data Fabric for Energy-Water R&D

Focal Area(s): 1) Data acquisition and assimilation enabled by machine learning, AI, and advanced methods including experimental/network design/optimization, unsupervised learning (including deep learning), and hardware-related efforts involving AI (e.g., edge computing). Science Challenge: DOE R&D, including DOE’s Basic Energy Research (BER)’s Environmental Systems Science Division (EESSD) program and DOE’s applied energy research (AER) programs (EERE, FE, and NE) are producers and consumers of Earth systems datasets. This white paper focuses on the first topic area from the call in relation to how crosscutting resources and innovations from DOE’s EESSD and AER can be brought to bear to mutual benefit and more efficient energy-water, Earth system data resources through improved. The overarching challenge posed by this call focuses on how DOE can directly leverage artificial intelligence (AI) to engineer a substantial (paradigm-changing) improvement in Earth System Predictability? While stemming from DOE BER’s EESSD program, this is a challenge that is faced and also being addressed by DOE’s AER programs. Over the past decade plus, FE, EERE, and NE programs have made important strides towards addressing this need. These strides are in many ways highly complementary to EESSD’s MODEX efforts. Energy water systems spanning metocean to groundwater to surface water systems all are data driven whether for basic energy or applied energy. These are remote, multi-variate, complex natural, and in many cases engineered, systems. Key needs and challenges of both EESSD and AER include developing data-focused tools to enhance data search and discovery to fill in knowledge gaps (address sparse data challenge), and rapidly transform datasets, including disparate and multi-source data. Leveraging DOE on-premise computing (HPC, exascale) infrastructure supports the computing-intensive algorithms required to execute these data acquisition and transformation processes to derive enriched knowledge and data, driving AI/ML and big data analytics for these systems. The opportunity lies in combining BER and AER efforts to provide a more robust, advanced, efficient and complete computing data fabric to address energy-water data acquisition and assimilation needs which currently pose significant impediments to AI/ML predictions and research.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Fabrication of MiniFuel Compacts for High-Power Irradiation Testing of TRISO Fuel

MiniFuel compacts containing 20 individual tristructural isotropic (TRISO)-coated fuel particles were characterized to provide supporting preirradiation characterization data. The preirradiated characterization data supports irradiation capsule design and safety analysis, as well as downstream postirradiation examination (PIE) for a planned MiniFuel irradiation to explore high particle powers. The analysis included dimensional inspection, x-ray radiography and tomography, as-fabricated defect fraction analysis, and a matrix impurity analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Fuel Fabrication and Single Stage Aqueous Process Modeling

The Material Protection, Accounting, and Control Technologies program utilizes modeling and simulation to assess Material Control and Accountability (MC&A) concerns for a variety of nuclear facilities. Single analyst tools allow for rapid design and evaluation of advanced approaches for new and existing nuclear facilities. A low enriched uranium (LEU) fuel conversion and fabrication facility simulator is developed to assist with MC&A for existing facilities. Measurements are added to the model (consistent with current best practices). Material balance calculations and statistical tests are also added to the model. In addition, scoping work is performed for developing a single stage aqueous reprocessing model. Preliminary results are presented and discussed, and next steps outlined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Report on FY 2020 Welding Parameters Optimization and the Fabrication of Qualified Alloy 709 Welds

Alloy 709 is an attractive candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 Intermediate Term Test Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. The phase of research reported herein focused on the issue of weld solidification cracking recently experienced in both experimental heats and a commercial heat of Alloy 709 with relatively high phosphorous levels.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Fabricating Diamond-like Amorphous Carbon

Using a magnetically confined hot hollow cathode PE-CVD, hydrocarbon gas is decomposed under a diluent gas to deposit hydrogenated amorphous carbon onto a sample holder. During the fabrication of the hydrogenated amorphous carbon, the electric potential, electron temperature, and electron density of the plasma are measured with a Langmuir probe. Raman spectroscopy is used to determine the structural and electronic characterization of the final hydrogenated amorphous carbon solid.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Report on FY 2021 Fabrication and Testing of Qualified Alloy 709 Welds at ORNL

Alloy 709 is a candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 ASME Code Case development team under the Advanced Reactor Technologies (ART) Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. This report summarizes the research conducted in FY 2021 and relevant results from previous reporting periods, aimed at welding commercial heat of Alloy 709 plates of relatively high phosphorous (P) level in support of ASME code case data package. Welding, code qualification tests, and associated microstructure characterization were carried out in determining the effect of P levels of weld wire on the weldability of the high P commercial heat of Alloy 709. The Alloy 709 weld creep strength was evaluated though preliminary creep testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Exploring Fabrication of Ultra-low Absorption, Multilayer, Hafnium High Reflectors

Ultra-low absorption, high damage threshold coatings are critical for the advancement of the high power CW laser technologies, and in most cases, are a limiting factor for the output power. Since high power CW laser systems enable extremely high power irradiances, when the light is incident on an HR mirror, part of the energy is absorbed and converted into heat, which can have many detrimental side effects. The worst-case scenarios are optical distortion and laser-induced damage. These optics must operate reliably with irradiances of 100's kW/cm 2 to MW/cm 2 . The highest pulsed laser damage threshold high reflectors are consistently fabricated with hafnia material. However, hafnia is not the material of choice for high power CW laser systems because of very high absorption and scatter properties, factors of >100x higher than tantala-silica, due to its poly crystalline nature. This study focuses on CW laser use applications, where the coatings’ laser damage resistance is largely limited by the inherent absorption of the coating materials. The goal is to study the feasibility of utilizing a “composite” hafnium-silica and a “doped” hafnia-silica target materials to prohibit crystallization. The results from the study were extremely successful. Hafnia high reflectors coatings generated from this study exhibited one micron absorption values of approximately 1 ppm, which are the lowest reported values to date.

36 MATERIALS SCIENCE↗