Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

The Effect of Indenter Ball Radius on the Static Load Capacity of the Superelastic 60NiTi for Rolling Element Bearings

Static load capacity is a critical design parameter for rolling element bearings used in space mechanisms because of the potential for Brinell (surface dent) damage due to shock and vibration loading events during rocket launch. Brinell damage to bearing raceways can lead to torque variations (noise) and reduced bearing life. The growing use of ceramic rolling elements with high stiffness in hybrid bearings exacerbates the situation. A new family of hard yet resilient materials based upon nickel-titanium is emerging to address such bearing challenges. 60NiTi is a superelastic material that simultaneously exhibits high hardness and a relatively low elastic modulus (approx. 100 GPa) and has been shown to endure higher indentation loads than conventional and high performance steel. Indentation load capacity has been reported for relatively large (12.7 mm diameter) ceramic (Si3N4) indenter balls pressed against flat plates of 60NiTi. In order to develop damage load threshold criteria applicable to a wide range of bearing designs and sizes, the effects of indenter ball radius and the accuracy of interpolation of the Hertz contact stress relations for 60NiTi must be ascertained. In this paper, results of indentation tests involving ceramic balls ranging from 6.4 to 12.7 mm in diameter and highly polished 60NiTi flat plates are presented. When the resulting dent depth data for all the indenter ball sizes are normalized using the Hertz equations, the data (dent depth versus stress) are comparable. Thus when designing bearings made from 60NiTi, the Hertz stress relations can be applied with relative confidence over a range of rolling element sizes and internal geometries.

bearings↗

The Effect of Indenter Ball Radius on the Static Load Capacity of the Superelastic 60NiTi for Rolling Element Bearings

Static load capacity is a critical design parameter for rolling element bearings used in space mechanisms because of the potential for Brinell (surface dent) damage due to shock and vibration loading events during rocket launch. Brinell damage to bearing raceways can lead to torque variations (noise) and reduced bearing life. The growing use of ceramic rolling elements with high stiffness in hybrid bearings exacerbates the situation. A new family of hard yet resilient materials based upon nickel-titanium is emerging to address such bearing challenges. 60NiTi is a superelastic material that simultaneously exhibits high hardness and a relatively low elastic modulus (approx. 100 GigaPascals) and has been shown to endure higher indentation loads than conventional and high performance steel. Indentation load capacity has been reported for relatively large (12.7 millimeters diameter) ceramic (Si3N4) indenter balls pressed against flat plates of 60NiTi. In order to develop damage load threshold criteria applicable to a wide range of bearing designs and sizes, the effects of indenter ball radius and the accuracy of interpolation of the Hertz contact stress relations for 60NiTi must be ascertained. In this paper, results of indentation tests involving ceramic balls ranging from 6.4 to 12.7 mm in diameter and highly polished 60NiTi flat plates are presented. When the resulting dent depth data for all the indenter ball sizes are normalized using the Hertz equations, the data (dent depth versus stress) are comparable. Thus when designing bearings made from 60NiTi, the Hertz stress relations can be applied with relative confidence over a range of rolling element sizes and internal geometries.

materials↗

Development of nano-Y2O3 dispersed Zr alloys synthesized by mechanical alloying and consolidated by pulse plasma sintering

Highlights: • Zr-Fe-Cr-Cu-Ti-1.0wt% nano-Y{sub 2}O{sub 3} dispersed alloys are fabricated by mechanical alloying and pulse plasma sintering. • These alloys record extremely high compressive strength, Young’s modulus, and hardness. • These mechanical properties are superior as compared to other commercially available Zr based alloys. • Dispersion of nanometric FeZr{sub 2}, Y{sub 2}Ti{sub 2}O{sub 7}, Fe{sub 2}Ti, ZrCu, Cr{sub 2}Zr, Y{sub 2}O{sub 3} leads to grain boundary pinning at elevated temperature. - Abstract: In this paper, Zr alloys are synthesized with nominal compositions: 50Zr-30Fe-10Cr-5Cu-5Ti (alloy A), and 49Zr-30Fe-10Cr-5Cu-5Ti-1Y{sub 2}O{sub 3} (alloy B), 45Zr-30Fe-10Cr-10Cu-5Ti (alloy C), 44Zr-30Fe-10Cr-10Cu-5Ti-1Y{sub 2}O{sub 3} (alloy D) (all in wt%) by mechanical alloying and consolidated by pulse plasma sintering at 1173 K (900 °C), 1223 K (950 °C) and 1273 K (1000 °C) using 75 MPa uniaxial pressure applied for 5 min and 70 kA pulsed current at 3 Hz pulse frequency. The microstructure and phase evolution during mechanical alloying and sintering has been characterized by X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM & TEM) and energy dispersive spectroscopy (EDS). Mechanical properties i.e. hardness and compressive strength were determined by using nano-indentation unit and universal testing machine. The produced alloys recorded very high levels of compressive strength (1359–2456 MPa), and hardness (7.05–10.05 GPa) which measures 1.5–2.0 times more than that of other Zr alloys (2 O{sub 3}) particles which can contribute to grain boundary pinning, and improved creep and oxidation resistance at elevated temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

HFTS-1 Natural Joint Data and Engineering Summary

This report provides an analysis of engineering and geologic data collected from the Hydraulic Fracturing Test Site #1 (HTSF-1) project in the southern Midland Basin, Reagan County, Texas. The site is being studied as part of the Science-informed Machine Learning for Accelerating Real-Time Decisions in Subsurface Applications (SMART) Initiative at the National Energy Technology Laboratory (NETL). The data collected is intended to provide a basis of understanding of the site and to construct simulation models. This report provides a summary analysis of the engineering and geologic data collected from the project to provide a basis of understanding of the site and to construct simulation models. The report examines various possible correlations in engineering properties based on natural fracture data from the program, which consisted of 11 horizontal wells, one vertical well, and one slant well. The horizontal wells are in two horizons: 1) Upper and 2) Middle Wolfcamp formations. Program data include: fracture frequency and fracture orientation data from four core runs in a slant well; fracture spacing and orientation from a vertical pilot well; laboratory triaxial testing and mineralogical determinations; and porosity results from magnetic resonance analyses from various wells, together with observations based on the data collection. In addition, available references were reviewed on the site for additional insights. As the focus of the report is on the natural system, hydraulic fracture data from the site were not examined in detail in this report. Data variability is the chief observation in examination of the database. Fracture frequency in the slant well can range from sections with values as high as five fractures per ft to sections up to 100+ ft in length with no natural observed fractures. Fracture spacing across is typically less than 10 ft, but can range up to hundreds of feet. Apparent fracturing shows the trends in two predominate orientations, E-SW and WNW-ESE, but minor variations exist. The rock units vary across the site from siliceous mudstones to calcareous mudstones, showing a general layering with depth. The laboratory properties such as strength and modulus show no apparent trend with depth, but appear to correlate with rock mineralogy with high strength and modulus values where calcium content is high. In addition, an attempt to examine variability and mineralogy on a larger scale was made using a color-coded system based on gamma ray measurements. A staged colored approach was adopted, presuming that lower gamma ray values indicate higher value of calcium content (blue scale) and that higher gamma ray values indicate higher clay mineral content (orange scale). As provided in report appendices, the system correlated well with visual examination of the slant core and the petrofabric analyses of the vertical pilot well. The results showed large variability in mineral content along the horizontal plane across the site. The change in mineral content was also rapid, on a scale less than that of the average hydraulic fracture stage length of about 180 ft.

42 ENGINEERING↗

Effect of Nb Content on Microstructures and Mechanical Properties of Ti-xNb-2Fe Alloys

β-Type Ti-Nb-based alloys exhibit satisfactory biocompatibility and low Young’s modulus for biomedical applications. The microstructure and mechanical properties of a series of Ti-(14, 16, 18, 20, 22, 24)Nb-2Fe alloys fabricated by arc melting were investigated by XRD, optical microscopy, and tensile tests. Both ω and α″ phases existed in the Ti-14Nb-2Fe alloy, while just a single β phase existed in the other alloys. Twinning is an important deformation mechanism that causes work hardening and twinning-induced plasticity. It was found in the Ti-(14, 16, 18, 20)Nb-2Fe alloys and not in the Ti-22Nb-2Fe alloy. The Ti-14Nb-2Fe alloy exhibited the highest tensile strength and the highest Young’s modulus owing to the existence of the ω phase. The tensile strength decreased gradually from 830 MPa (highest) for the Ti-14Nb-2Fe alloy to 540 MPa (lowest) for the Ti-24Nb-2Fe alloy with an increase in the Nb content. The Young’s modulus decreased from 90 GPa for the Ti-14Nb-2Fe alloy to 63 GPa for the Ti-22Nb-2Fe alloy and then increased to 71 GPa for the Ti-24Nb-2Fe alloy. Elongation shows the same trend as the Young’s modulus. The Ti-22Nb-2Fe alloy, with a low Young’s modulus of 63 GPa, tensile strength of 570 MPa, and 15% elongation, was found suitable for biomedical applications. The Ti-20Nb-2Fe alloy also exhibits a high tensile strength, a Young’s modulus ratio of 9.24 × 10{sup −3}, and 18% elongation and is thus considered another valuable Ti alloy for biomedical applications.

36 MATERIALS SCIENCE↗

Ultrastrong, Stiff and Multifunctional Carbon Nanotube Composites

Carbon nanotubes (CNTs) are an order of magnitude stronger than any current engineering fiber. However, for the past two decades it has been a challenge to utilize their reinforcement potential in composites. Here we report CNT composites with unprecedented multifunctionalities, including record high strength (3.8 GPa), Young s modulus (293 GPa), electrical conductivity (1230 S cm-1) and thermal conductivity (41 W m-1 K-1). These superior properties are derived from the long length, high volume fraction, good alignment and reduced waviness of the CNTs, which were produced by a novel processing approach that can be easily scaled up for industrial production.

Carbon Nanotubes↗

Measurement of Young’s modulus and damping of fibers at cryogenic temperatures

High-yield inertial confinement fusion targets are at cryogenic temperatures and must remain stable to within 10 um during the implosion. Young’s modulus and damping properties of fibers used to mount cryogenic targets are needed to design stable targets, but these property values do not exist in literature. A novel experimental method that tracks how target vibrations respond to an impulse is used to quantitatively measure these properties from 295 to 20 K. Young’s modulus and the critical damping ratio are measured for Nicalon^TM ceramic grade [silicon carbide (SiC)], Zylon HM {poly[p-phenlyne- 2,6-benzobisoxazole] (PBO)}, M5 {dimidazo-pyridinylene [dihydroxy] phenylene (PIPD)}, and polyimide fibers. This method allows one to accurately measure the properties of interest for fiber diameters as small as 12 um at ~ 20 K. Significant changes are seen in Young’s modulus for the three polymeric fibers with respect to temperature; while Young’s modulus is relatively invariant to temperature for the ceramic fiber.

Cryogenic temperature↗

First-principles study, fabrication, and characterization of (Hf 0.2 Zr 0.2 Ta 0.2 Nb 0.2 Ti 0.2 )C high-entropy ceramic

The formation possibility of (Hf 0.2 Zr 0.2 Ta 0.2 Nb 0.2 Ti 0.2 )C high-entropy ceramic (HHC-1) was first analyzed by the first-principles calculations, and then, it was successfully fabricated by hot-pressing sintering technique at 2073 K under a pressure of 30 MPa. The first-principles calculation results showed that the mixing enthalpy and mixing entropy of HHC-1 were -0.869 ± 0.290 kJ/mol and 0.805R, respectively. The experimental results showed that the as-prepared HHC-1 not only had an interesting single rock-salt crystal structure of metal carbides but also possessed high compositional uniformity from nanoscale to microscale. By taking advantage of these unique features, it exhibited extremely high nanohardness of 40.6 ± 0.6 GPa and elastic modulus in the range from 514 ± 10 to 522 ± 10 GPa and relatively high electrical resistivity of 91 ± 1.3 μΩ·cm, which could be due to the presence of solid solution effects.

36 MATERIALS SCIENCE↗

Stabilizing Dendritic Electrodeposition by Limiting Spatial Dimensions in Nanostructured Electrolytes.

The tendency of metals to form uncontrolled dendritic morphologies during electrodeposition hinders the development of safe and reliable metal batteries. Multiphase nanostructured electrolytes can suppress dendritic growth if the mechanical modulus of the electrolyte is high relative to that of the metal or if the conducting channels are confined to nanoscale dimensions. Direct visualization and analysis of electrodeposition within polymeric nanostructures elucidates the structure-property relationships and mechanisms underlying the suppression of dendrite growth. Here, we fabricate precisely structured multiphase films composed of nanochannels of a polymeric electrolyte in a background of nonconductive polymer on top of coplanar electrodes. The devices enable imaging and analysis of electrodeposition behavior as a function of channel width by scanning electron microscopy. We find that electrodeposition is confined to individual conductive channels and that radial propagation of the dendritic morphology is suppressed in channels for which the width is smaller than the characteristic dendritic nucleation size.

Sharon, Daniel↗

Pressure-induced amorphization and porosity modification in a metal-organic framework.

The impact of modest, industrially accessible pressures (0-1.2 GPa) on the structure and porosity of the zeolitic imidazolate framework Zn(2-methylimidazole){sub 2}, ZIF-8, was investigated using in situ powder X-ray diffraction in combination with sorption measurements for pressure-treated samples. The framework is highly compressible, with a bulk modulus (K = -V {partial_derivative}P/{partial_derivative}V) of 6.52(35) GPa, the most compressible metal-organic framework (MOF) documented to date. The framework undergoes an irreversible pressure-induced amorphization following compression beyond 0.34 GPa. The pressure-amorphized ZIF-8 remains porous, although the sorption characteristics are distinctly altered compared to the pristine material. As such, pressure can provide a new route to systematically modify the sorption behavior and other functional properties of MOFs, a nontraditional form of postsynthetic modification. Importantly, pressure modification of MOFs is effective at lower pressures than in other porous materials (e.g., zeolites) and, as such, is easily scalable and industrially relevant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic behavior of chemically tunable mechano-responsive hydrogels

Here, using theory and simulation, we model the mechanical behavior of gels that encompass loops and dangling chain ends. If the loops remain folded and dangling ends are chemically inert, then these topological features just serve as defects. If, however, the loops unfold to expose the hidden (“cryptic”) binding sites and the ends of the dangling chains are reactive, these moieties can form bonds that improve the gel's mechanical properties. For gels with a lower critical solubility temperature (LCST), we systematically switch on the possible unfolding and binding events. To quantify the resulting effects, we derive equations for the gel's equilibrium and dynamic elastic moduli. We also use a finite element approach to simulate the gel's response to deformation and validate the analytic calculations. Herein, we show that the equilibrium moduli are highly sensitive to the presence of unfolding and binding transitions. The dynamical moduli are sensitive not only to these structural changes, but also to the frequency of deformation. For example, when reactive ends bind to exposed cryptic sites at T = 29 °C and relatively high frequency, the storage shear modulus is 119% greater than the corresponding equilibrium value, while the storage Young's modulus is 109% greater than at equilibrium. These findings provide guidelines for tuning the chemical reactivity of loops and dangling ends and the frequency of deformation to tailor the mechano-responsive behavior of polymer networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure and tribological properties of Ti-contained amorphous carbon film deposited by DC magnetron sputtering

Pure amorphous carbon (a-C) film and that with a small amount of Ti were deposited on high speed steel (W18Cr4V) substrates by means of dc closed field unbalanced magnetron sputtering. The chemical composition and microstructure of the a-C films were performed using x-ray photoelectron spectroscopy, x-ray diffraction, Raman spectra, and transmission electron microscopy. The mechanical and tribological properties were evaluated using a nanoindentor, Rockwell and scratch tests, and a conventional ball-on-disk tribometer, respectively. The pure a-C film showed the high hardness (53 GPa), elastic modulus (289 GPa), but the poor adhesive strength. When adding a small amount of Ti to the a-C film, both the adhesive strength and the tribological properties were improved. The Ti contained a-C film had the low wear rate (1.9x10{sup -17} m{sup 3} N{sup -1} m{sup -1}) and friction coefficient in humid air.

36 MATERIALS SCIENCE↗

Grayscale Digital Light Processing Gradient Printing for Stress Concentration Reduction and Material Toughness Enhancement

Avoiding stress concentrations is essential to achieve robust parts since failure tends to originate at such concentrations. With recent advances in multimaterial additive manufacturing, it is possible to alter the stress (or strain) distribution by adjusting the material properties in selected locations. Here, we investigate the use of grayscale digital light processing (g-DLP) 3D printing to create modulus gradients around areas of high stress. These gradients prevent failure by redistributing high stresses (or strains) to the neighboring material. The improved material distributions are calculated using finite element analysis. The much-enhanced properties are demonstrated experimentally for thin plates with circular, triangular, and elliptical holes. In conclusion, this work suggests that multimaterial additive manufacturing techniques like g-DLP printing provide a unique opportunity to create tougher engineering materials and parts.

36 MATERIALS SCIENCE↗

Shear failure and impact resistance in graphite fiber laminates

The multispan beam (MSB) test was evaluated as a predictor of damage resistance and damage tolerance in quasi-isotropic graphite laminates. Materials studied were five commercial prepreg system using high-strain and intermediate-modulus carbon fibers, as well as an amorphous thermoplastic system. Failure loads and displacements in the MSB tests showed little rate dependence. Values of compressive strength after a standard low-velocity impact correlated fairly well with the MSB results.

Srinivasan, Krishna↗

Lightweight, Wearable, Metal Rubber Sensor

For autonomous health monitoring. NanoSonic, Inc., has developed comfortable garments with multiple integrated sensors designed to monitor astronaut health throughout long-duration space missions. The combined high electrical conductivity, low mechanical modulus, and environmental robustness of the sensors make them an effective, lightweight, and comfortable alternative to conventional use of metal wiring and cabling.

Hill, Andrea↗

Mechanical and spectroscopic properties of metal-containing polyimides

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymerization or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Taylor, L. T.↗

Mechanical and spectroscopic properties of metal containing polyimides

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymermzation or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Taylor, L. T.↗

Mechanical behavior of La0.8Sr0.2Ga0.8Mg0.2O3 perovskites

Mechanical properties such as Young's modulus, fracture toughness and slow crack growth have been measured for phase pure and highly dense (<5% porosity) La0.8Sr0.2Ga0.8Mg0.2O3 perovskites. The Young's modulus was measured to be ~175 GPa, while strength and fracture toughness both exhibited low values confirming the poor mechanical properties of the material. LSGM was also proved to be highly susceptible to slow crack growth in humid air at room temperature where in order to survive a one year period the static stresses in the material should be as low as 50 MPa for a 50% failure probability.

36 MATERIALS SCIENCE↗