Search NASA⌕ Search

SEARCH · Search NASA

Results for “impulse test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Performance of a FAKEL K10K Resistojet

A model K10K resistojet produced by FAKEL Enterprise was evaluated at steady-state conditions with both nitrogen and xenon propellants. Performance and operational characteristics were documented for cold gas and heater power levels up to 8 W at mass flow rates from 0.02 to 0.2 g/s. Maximum specific impulses of 84 s on nitrogen and 49 s on xenon were achieved at the highest specific power levels tested.

Jankovsky, Robert S.↗

Design Evolutuion of Hot Isotatic Press Cans for NTP Cermet Fuel Fabrication

Nuclear Thermal Propulsion (NTP) is under consideration for potential use in deep space exploration missions due to desirable performance properties such as a high specific impulse (> 850 seconds). Tungsten (W)-60vol%UO2 cermet fuel elements are under development, with efforts emphasizing fabrication, performance testing and process optimization to meet NTP service life requirements [1]. Fuel elements incorporate design features that provide redundant protection from crack initiation, crack propagation potentially resulting in hot hydrogen (H2) reduction of UO2 kernels. Fuel erosion and fission product retention barriers include W coated UO2 fuel kernels, W clad internal flow channels and fuel element external W clad resulting in a fully encapsulated fuel element design as shown.

Mireles, O. R.↗

Small, high-pressure liquid oxygen turbopump

A small, high-pressure, liquid oxygen turbopump was designed, fabricated, and tested. The pump was of a single-stage, centrifugal type; power to the pump was supplied by a single-stage, partial emission, axial-impulse turbine. Design conditions included an operating speed of 70,000 rpm, pump discharge pressure of 2977 N/sq cm (4318 psia), and a pump flowrate of 16.4 kg/s (36.21 lb/sec). The turbine was propelled by LO2/LH2 combustion products at 1041 K (1874 R) inlet temperature, and at a design pressure ratio of 1.424. The approaches used in the detail analysis and design of the turbopump are described, and fabrication methods are discussed. Data obtained from gas generator tests, turbine performance calibration, and turbopump testing are presented.

Csomor, A.↗

A test technique for measuring lightning-induced voltages on aircraft electrical circuits

The development of a test technique used for the measurement of lightning-induced voltages in the electrical circuits of a complete aircraft is described. The resultant technique utilizes a portable device known as a transient analyzer capable of generating unidirectional current impulses similar to lightning current surges, but at a lower current level. A linear relationship between the magnitude of lightning current and the magnitude of induced voltage permitted the scaling up of measured induced values to full threat levels. The test technique was found to be practical when used on a complete aircraft.

Walko, L. C.↗

The Superorbital Expansion Tube concept, experiment and analysis

In response to the need for ground testing facilities for super orbital re-entry research, a small scale facility has been set up at the University of Queensland to demonstrate the superorbital expansion tube concept. This unique device is a free piston driven, triple diaphragm, impulse shock facility which uses the enthalpy multiplication mechanism of the unsteady expansion process and the addition of a secondary shock driver to further heat the driver gas. The pilot facility has been operated to produce quasi-steady test flows in air with shock velocities in excess of 13 km/s and with a usable test flow duration of the order of 15 micro sec. an experimental condition produced in the facility with total enthalpy of 108 MJ/kg and a total pressure of 335 MPa is reported. A simple analytical flow model which accounts for non-ideal rupture of the light tertiary diaphragm and the resulting entropy increase in the test gas is discussed. It is shown that equilibrium calculations more accurately model the unsteady expansion process than calculations assuming frozen chemistry. This is because the high enthalpy flows produced in the facility can only be achieved if the chemical energy stored in the test flow during shock heating of the test gas is partially returned to the flow during the process of unsteady expansion. Measurements of heat transfer rates to a flat plate demonstrate the usability of test flow for aerothermodynamic testing and comparison of these rates with empirical calculations confirms the usable accuracy of the flow model.

Neely, A. J.↗

On the accuracy of the pseudocompressibility method in solving the incompressible Navier-Stokes equations

The method of pseudocompressibility is being tested for its accuracy in solving the incompressible Navier-Stokes equations. An implicit, finite-difference computer code is used to solve the equations in a three-dimensional, curvilinear coordinate system. The code employs artificial compressibility for solving the pressure field, coupled with an implicit, approximate-factorization scheme. This coupling is known as the pseudocompressibility method. The pseudocompressibility method introduces pressure waves of finite speed into the fluid medium that would otherwise have an infinite sound speed. The waves die out as the solution converges, and the steady state solution approaches a divergence-free condition. However, these waves limit the time-accuracy of the computations. The effects of these waves are analyzed and criteria are set for choosing the pseudocompressibility parameters that govern the pressure wave speed. Test cases are presented that verify these criteria. The code is tested by computing laminar flow over a two-dimensional, backward-facing step and over a two-dimensional, impulsively started circular cylinder.

Rogers, S. E.↗

On the accuracy of the pseudocompressibility method in solving the incompressible Navier-Stokes equations

The method of pseudocompressibility is tested for its accuracy in solving the incompressible Navier-Stokes equations. An implicit, finite difference computer code is used to solve the equations in a three-dimensional, curvilinear coordinate system. The code employs artificial compressibiity for solving the pressure field, coupled with an implicit, approximate factorization scheme. This coupling is known as the pseudocompressibility method and introduces pressure waves of finite speed into the fluid medium that would otherwise have an infinite sound speed. The waves die out as the solution converges, and the steady state solution approaches a divergence-free condition. These waves, however, limit the time accuracy of the computations. The effects of these waves are analysed and criteria are set for choosing the pseudocompressibility parameter that governs the pressure wave speed; test cases are presented that verify these criteria. The code is tested by computing laminar flow over a two-dimensional, backward-facing step and over a two-dimensional, impulsively started circular cylinder.

Rogers, S. E.↗

Space Station propulsion - Advanced development testing of the water electrolysis concept at MSFC

The successful demonstration at Marshall Space Flight Center (MSFC) that the water electrolysis concept is sufficiently mature to warrant adopting it as the baseline propulsion design for Space Station Freedom is described. In particular, the test results demonstrated that oxygen/hydrogen thruster, using gaseous propellants, can deliver more than two million lbf-seconds of total impulse at mixture ratios of 3:1 to 8:1 without significant degradation. The results alao demonstrated succcessful end-to-end operation of an integrated water electrolysis propulsion system.

Jones, Lee W.↗

Experimental performance of a high-area-ratio rocket nozzle at high combustion chamber pressure

An experimental investigation was conducted to determine the thrust coefficient of a high-area-ratio rocket nozzle at combustion chamber pressures of 12.4 to 16.5 MPa (1800 to 2400 psia). A nozzle with a modified Rao contour and an expansion area ratio of 1025:1 was tested with hydrogen and oxygen at altitude conditions. The same nozzle, truncated to an area ratio of 440:1, was also tested. Values of thrust coefficient are presented along with characteristic exhaust velocity efficiencies, nozzle wall temperatures, and overall thruster specific impulse.

Jankovsky, Robert S.↗

Status of the RBCC Direct-Connect Mixer Combustor Experiment

The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.

Walker, James F.↗

Status of the RBCC Direct-Connect Mixer Combustor Experiment

The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.

Walker, James F.↗

Magnetoelastic sensors in combination with nanometer-scale honeycombed thin film ceramic TiO2 for remote query measurement of humidity

Ribbonlike magnetoelastic sensors can be considered the magnetic analog of an acoustic bell; in response to an externally applied magnetic field impulse the sensors emit magnetic flux with a characteristic resonant frequency. The magnetic flux can be detected external to the test area using a pick-up coil, enabling query remote monitoring of the sensor. The characteristic resonant frequency of a magnetoelastic sensor changes in response to mass loads. [L.D. Landau and E. M. Lifshitz, Theory of Elasticity, 3rd ed. (Pergamon, New York, 1986). p. 100].Therefore, remote query chemical sensors can be fabricated by combining the magnetoelastic sensors with a mass changing, chemically responsive layer. In this work magnetoelastic sensors are coated with humidity-sensitive thin films of ceramic, nanodimensionally porous TiO2 to make remote query humidity sensors. c2000 American Institute of Physics.

NASA Discipline Life Sciences Technologies↗

A Nuclear Cryogenic Propulsion Stage for Near-Term Space Missions

Development efforts in the United States have demonstrated the viability and performance potential of NTP systems. For example, Project Rover (1955 - 1973) completed 22 high power rocket reactor tests. Peak performances included operating at an average hydrogen exhaust temperature of 2550 K and a peak fuel power density of 5200 MW/m3 (Pewee test), operating at a thrust of 930 kN (Phoebus-2A test), and operating for 62.7 minutes on a single burn (NRXA6 test). Results from Project Rover indicated that an NTP system with a high thrust-toweight ratio and a specific impulse greater than 900 s would be feasible. Excellent results have also been obtained by Russia. Ternary carbide fuels developed in Russia may have the potential for providing even higher specific impulses.

Houts, Michael G.↗

Three-Dimensional Analysis and Modeling of a Wankel Engine

A new computer code, AGNI-3D, has been developed for the modeling of combustion, spray, and flow properties in a stratified-charge rotary engine (SCRE). The mathematical and numerical details of the new code are described by the first author in a separate NASA publication. The solution procedure is based on an Eulerian-Lagrangian approach where the unsteady, three-dimensional Navier-Stokes equations for a perfect gas-mixture with variable properties are solved in generalized, Eulerian coordinates on a moving grid by making use of an implicit finite-volume, Steger-Warming flux vector splitting scheme. The liquid-phase equations are solved in Lagrangian coordinates. The engine configuration studied was similar to existing rotary engine flow-visualization and hot-firing test rigs. The results of limited test cases indicate a good degree of qualitative agreement between the predicted and measured pressures. It is conjectured that the impulsive nature of the torque generated by the observed pressure nonuniformity may be one of the mechanisms responsible for the excessive wear of the timing gears observed during the early stages of the rotary combustion engine (RCE) development. It was identified that the turbulence intensities near top-dead-center were dominated by the compression process and only slightly influenced by the intake and exhaust processes. Slow mixing resulting from small turbulence intensities within the rotor pocket and also from a lack of formation of any significant recirculation regions within the rotor pocket were identified as the major factors leading to incomplete combustion. Detailed flowfield results during exhaust and intake, fuel injection, fuel vaporization, combustion, mixing and expansion processes are also presented. The numerical procedure is very efficient as it takes 7 to 10 CPU hours on a CRAY Y-MP for one entire engine cycle when the computations are performed over a 31 x16 x 20 grid.

Raju, M. S.↗

Acoustic Improvements to the 9- by 15-Foot Low Speed Wind Tunnel

A major refurbishment of the 9- by 15-Foot Low Speed Wind Tunnel at NASA Glenn Research Center was undertaken between 2016 and 2019 to improve the acoustic measurement capability of the facility. The principal objective was to lower the background noise in the test section so quiet aircraft propulsors could be tested with good signal-to-noise ratio. The secondary objective was to improve the anechoic quality of the facility so that the measurement uncertainty would be reduced and the data collected would be more accurate. The results of the project were a vastly improved anechoic wind tunnel, with one-third octave sound levels reduced by 8 to 18 dB in the frequency range of interest. The anechoic quality of the test section was improved substantially, reducing the effect of unwanted echoes contaminating the noise measurements, with the error in an impulse response measurement reduced from 0.8 dB to 0.2 dB. This report describes the main acoustic findings and is intended to provide guidance for other facilities requiring a low noise environment

Wind tunnel↗

A Psychoacoustic Test for Urban Air Mobility Vehicle Sound Quality

This paper describes a psychoacoustic test in the Exterior Effects Room (EER) at the NASA Langley Research Center. The test investigated the degree to which sound quality metrics (sharpness, tonality, etc.) are predictive of annoyance to notional sounds of Urban Air Mobility (UAM) vehicles (i.e., air taxis). A suite of 136 unique (4.6 second duration) UAM rotor noise stimuli was generated. These stimuli were based on aeroacoustic predictions of a NASA reference UAM quadrotor aircraft under two flight conditions. The synthesizer changed rotor noise parameters such as the blade passage frequency, the relative level of broadband self-noise, and the relative level of tonal motor noise. With loudness constant, the synthesis parameters impacted sound quality in a way that created a spread of predictors both in synthesizer parameters and in sound quality metrics. Forty subjects listened to the suite of UAM noise stimuli in the EER and judged each sound individually on a standard scale of annoyance. Additionally, a subset of the UAM noise stimuli were compared to a reference sound that varied in loudness. From these responses, the relative effect of changes in loudness or changes in other sound quality metrics on annoyance was evaluated. This paper covers background and motivation for the test, details of how the sound stimuli were generated, and details of the test design and execution. Test results investigate how sound quality may affect perceived annoyance to UAM vehicle noise, indicating the importance of sharpness, tonality, impulsiveness, and roughness on annoyance to UAM noise.

UAM↗

Cislunar Trajectory Design and Maneuver Autonomy for NASA's Moon to Mars Architecture

NASA’s Moon to Mars architecture is an ambitious roadmap of manned cislunar and deep space exploration. The extensive amount of orbital assets required will place a significant burden on ground-based resources, such as communication networks and operations facilities. Spacecraft autonomy is essential for maintaining a vast number of complex missions beyond Earth orbit. To achieve full autonomy, spacecraft must be able to employ methods of robust maneuver design without an explicit dependence on commands sent from the ground. This level of autonomy is needed not only for stationkeeping, but also for outbound transfers. To address the need of spacecraft maneuver design autonomy, this work investigates the use of neural networks (NNs) in a supervised learning environment. A supervised learning approach for NNs allows for a curated training data set, consisting exclusively of perturbations applied to a desired mission concept of operations (ConOps). The proposed approach allows humans on the ground to design a specific mission ConOps before flight, then employ NNs to fly the mission robustly and autonomously. This investigation numerically tests maneuver autonomy in four highly sensitive regions of flight: orbit raising, translunar injection burns, powered lunar flybys, and invariant manifold insertion burns. These straining cases are contextualized by testing them in a demonstration mission, targeting an Earth-Moon L3 orbit. The study first establishes feasibility by automating impulsive burn maneuvers. However, some guidance algorithms will need more intensive commands, such as inertial pointing and angular rates. To validate this method, NN maneuver autonomy is applied to a finite burn model of the demonstration mission. The use of sequential, mission specific maneuvers provide an appropriate testbed to demonstrate the robustness of a NN trained on feasible perturbed states. Moreover, these scenarios provide preliminary proof-of-concept for fully autonomous missions that execute maneuvers without dependence upon explicit command uplinks. As a result, the technological advancement proposed in this work may significantly ease the strain on ground-based mission operations. This would enable complex and autonomous mission execution in cislunar and deep space regimes, filling a technology gap required to support future manned missions.

NASA↗

Method and apparatus to produce high specific impulse and moderate thrust from a fusion-powered rocket engine

A system and method for producing and controlling high thrust and desirable specific impulse from a continuous fusion reaction is disclosed. The resultant relatively small rocket engine will have lower cost to develop, test, and operate that the prior art, allowing spacecraft missions throughout the planetary system and beyond. The rocket engine method and system includes a reactor chamber and a heating system for heating a stable plasma to produce fusion reactions in the stable plasma. Magnets produce a magnetic field that confines the stable plasma. A fuel injection system and a propellant injection system are included. The propellant injection system injects cold propellant into a gas box at one end of the reactor chamber, where the propellant is ionized into a plasma. The propellant and fusion products are directed out of the reactor chamber through a magnetic nozzle and are detached from the magnetic field lines producing thrust.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗