Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Temperature and radiation effects on brittle versus ductile fracture behavior in miscible phase boundaries: insight from atomistic simulations

Temperature- and irradiation-assisted failure mechanisms in miscible phase boundaries are clarified via atomistic calculations. We first establish the temperature-dependent brittle-to-ductile transition in U–Zr miscible phase boundaries. Our results confirm that these boundaries are mostly brittle at low temperatures and ductile at elevated temperatures. We then investigate the changes induced by irradiation on the fracture mechanisms in such phase boundaries. The irradiation-induced defect accumulation follows a multi-stage process that starts with the accumulation of isolated small dislocation loops before transitioning to the saturation and growth of larger dislocation loops and end up with a reorganization into forest dislocations. The accumulation of loops is the primary feature to participate in the delineation between brittle and ductile interfacial fracture in irradiated phase boundaries. At low damage levels, radiation defect interactions with the crack tip are limited and U–Zr miscible boundaries fail through the emission of dislocations ahead of the crack tip followed by brittle cleavage in agreement with the classical Griffith’s criterion for crack stability. At higher damage levels, the failure mode transitions from brittle crack growth to ductile void growth. In this case, the microcrack tip is blunted by the high density of pre-existing, radiation-induced defects in the vicinity of the crack. This interaction leads to the development and growth of a cavity at the interface as opposed to interfacial cleavage.

36 MATERIALS SCIENCE↗

Durability of plasma sprayed Thermal Barrier Coatings with controlled properties part Ⅱ: Effects of geometrical curvature

The present investigation elucidates the effects of substrate curvature on the durability of Air Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs). Traditionally, planar disk specimens are utilized in Furnace Cycle Testing (FCT). In most cases, delamination is initiated at the disk's free edge and then propagates along the TBC-bond coat interface. However, in turbine components (e.g., blades/vanes), they lack significant free edges and the coatings are deposited on non-flat surfaces of varying radii of curvature. These geometrical discrepancies imply significant differences in the stress states as compared to planar disk specimens. Therefore, the part geometry inevitably affects the TBC failure mechanisms in the turbine system, and consequently influences TBC durability. Nevertheless, these effects have not been fully explored in the past, despite the anecdotal knowledge which suggests the leading edge of turbine blades to be one of the most common failure/spallation locations. Here in this study, representative TBC systems were deposited onto superalloy disks with flat substrate and rods with curved substrate. The experimental results from FCT suggest TBC durability on rods is significantly lower than when sprayed on disks. Furthermore, the durability of TBCs on rods appears to increase with higher porosity, which is contradictory to reported trends for TBCs on disks. In addition, the effects of various bond coats are not consistent with those observed in disks. To clarify the underlying effects of curved geometries, detailed stress analyses were performed. They revealed a state of thermal stresses which is unique to curved geometries. It was found that TBC on rods experience tensile radial stresses as well as tensile hoop stresses during the cooling. These stresses result in a complex interplay in failure processes in rods, which explains the different observed trends in the durability from those obtained with disks.

36 MATERIALS SCIENCE↗

The Effect of Artificial SEIs on Lithium Metal Anode Morphology and Conductivity

Lithium metal has often been termed the “holy grail” of battery technology, due to its high capacity (2,061 mAh/cm3) and low electrochemical potential (-3.04 V vs. SHE). However, lithium’s beneficially low potential also causes it to be highly reactive in the presence of organic solvents, making it difficult to harness the high energy capabilities for rechargeable batteries. Common failure of lithium metal batteries occurs by rapid dendrite growth leading to a hazardous short-circuit. Various methods have been brought forth to better understand the fundamental mechanisms of lithium metal batteries, as well as modifications made to better stabilize lithium metal. A common route of modification is done through interface engineering, with attempts to artificially provide a stable, homogeneous solid-electrolyte interface (SEI). The stability of the SEI has direct effects on the heterogeneity of the electrode surface, which initiates a waterfall effect of for progressive reactions such as dendrite growth, dead lithium accumulation, and electrolyte consumption. This work aims to produce a mixed LiI-LiF artificial SEI to improve ionic conductivity while retaining a high elastic modulus.

25 ENERGY STORAGE↗

A Novel Shim-Assisted Resistance Spot Welding Process to Improve Weldability of Medium-Mn Transformation-Induced Plasticity Steel

Medium-Mn transformation-induced plasticity steels have great potential to significantly reduce vehicle weight and improve fuel economy due to their outstanding combination of high strength and excellent ductility. One bottleneck to the application is their poor weldability resulting from their high Mn contents. In this paper, three resistance spot welding set-ups, including no shim, an interstitial-free steel shim at the faying interface (shim-in) and shims against the electrodes (shim-out), were incorporated to investigate the weldability of Fe-7Mn-0.14C medium-Mn steel. Tensile-shear, cross-tension, and microhardness tests were used to evaluate the mechanical properties of the welds. Experimental results demonstrated that the failure mode of the welds transitioned from the interfacial fracture in the case of no shim to the desired nugget pull-out fracture in the shim-out set-up, resulting in dramatical improvements in both peak loads and their corresponding extensions during the tensile-shear and cross-tension tests. In contrast, the shim-in set-up made no improvement. What can contribute to such improvement was then discussed on the basis of observed morphologies and microstructures of welds.

36 MATERIALS SCIENCE↗

Inference of phase field fracture models

The phase field approach to modeling fracture uses a diffuse damage field to represent cracks. This representation mollifies singularities that arise in computations with sharp interface models and some of the resultant difficulties in the mathematical and numerical treatment of fracture. Phase field fracture models have proven effective at representing crack propagation, branching, and merging. Specific formulations, beginning with brittle fracture, have also been shown to converge to classical solutions. Extensions to cover the range of material failure, including ductile and cohesive fracture, lead to an array of possible models. There exists a large body of literature focusing on this class of models and on the impact of model form on the predicted crack evolution. However, there have not been systematic studies into how optimal models may be chosen. Here, we take a first step in this direction by developing formal methods for identification of the best parsimonious model of phase field fracture given full-field data on the damage and deformation fields. We consider some of the main models that have been used for the degradation of elastic response due to damage and its propagation. Our approach builds upon Variational System Identification (VSI), a weak form variant of the Sparse Identification of Nonlinear Dynamics (SINDy). Furthermore, in this first communication we focus on synthetically generated data but we also consider central issues associated with the use of experimental full-field data, such as data sparsity and noise.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lithium inventory tracking as a non-destructive battery evaluation and monitoring method

Tracking the active lithium (Li) inventory in an electrode shows the true state of a Li battery, akin to a fuel gauge for an engine. However, non-destructive Li inventory tracking is currently unavailable. Here, in this work, we used the theoretical capacity of a transition metal oxide to convert capacity into a Li inventory analysis. The Li inventory in electrodes was tracked reliably to show how battery formulations and test methods affect performance. Contrary to capacity, Li inventory tracking reveals stoichiometric variations near the electrode–electrolyte interface. Verifiable results rationalized differences in measurements, clarifying and reducing interferences from cell formulations and experimental manipulations. By tracing four variables from formation to end-of-life, we characterize electrode and cell performance with a thermodynamic framework. Accurate rationalization of subtle differences in Li inventory utilization promises precise battery engineering, evaluation, failure analysis and risk mitigation. The method could be applicable from cell design optimization and fabrication to battery management, improving battery performance and reliability.

25 ENERGY STORAGE↗

DIVA/DeviceEditor v6.1.2

DIVA is an end-to-end DNA design and construction management platform that streamlines how researchers design, build, and receive sequence-verified DNA constructs. Through a web-based BioCAD interface (DeviceEditor), researchers independently design DNA constructs and submit them to a centralized queue with a single action. Designs progress transparently through standardized states which allow researchers to track status and access finished constructs via a central DNA repository. Submitted designs are reviewed by dedicated staff for feasibility and optimization, reducing costly failures and improving downstream execution. Automated DNA assembly software optimizes construction strategies by reusing existing parts where possible and sourcing synthetic DNA only when needed. Standardized, sequence-agnostic assembly methods enable many independent constructs to be built in parallel using lab automation, dramatically increasing throughput. High-throughput next-generation sequencing is used to verify construct accuracy, with flexible platforms selected based on task requirements. Throughout the process, detailed success and failure data are captured and analyzed, enabling continuous improvement of assembly protocols. Compared to traditional, manual DNA construction workflows, DIVA offers higher scalability, transparency, reproducibility, and data-driven optimization.

Plahar, Hector [Lawrence Berkeley National Laborat↗

Resilience Design Patterns: A Structured Approach to Resilience at Extreme Scale

Reliability is a serious concern for future extreme-scale high-performance computing (HPC) systems. Projections based on the current generation of HPC systems and technology roadmaps suggest the prevalence of very high fault rates in future systems. While the HPC community has developed various resilience solutions, application-level techniques as well as system-based solutions, the solution space remains fragmented. There are no formal methods and metrics to integrate the various HPC resilience techniques into composite solutions, nor are there methods to holistically evaluate the adequacy and efficacy of such solutions in terms of their protection coverage, and their performance \& power efficiency characteristics. Additionally, few of the current approaches are portable to newer architectures and software environments that will be deployed on future systems. In this paper, we develop a structured approach to the design, evaluation and optimization of HPC resilience using the concept of design patterns. A design pattern is a general repeatable solution to a commonly occurring problem. We identify the problems caused by various types of faults, errors and failures in HPC systems and the techniques used to deal with these events. Each well-known solution that addresses a specific HPC resilience challenge is described in the form of a pattern. We develop a complete catalog of such resilience design patterns, which may be used by system architects, system software and tools developers, application programmers, as well as users and operators as essential building blocks when designing and deploying resilience solutions. We also develop a design framework that enhances a designer's understanding the opportunities for integrating multiple patterns across layers of the system stack and the important constraints during implementation of the individual patterns. It is also useful for defining mechanisms and interfaces to coordinate flexible fault management across hardware and software components. The resilience patterns and the design framework also enable exploration and evaluation of design alternatives and support optimization of the cost-benefit trade-offs among performance, protection coverage, and power consumption of resilience solutions. Here, the overall goal of this work is to establish a systematic methodology for the design and evaluation of resilience technologies in extreme-scale HPC systems that keep scientific applications running to a correct solution in a timely and cost-efficient manner despite frequent faults, errors, and failures of various types.

97 MATHEMATICS AND COMPUTING↗

An inelastic homogenization framework for layered materials with planes of weakness

Many geologic materials have a composite structure, in which macroscopic mechanical behavior is determined by the properties, shape, and heterogeneous distribution of individual constituents. In particular, sedimentary rocks commonly exhibit a layered microstructure, with distinct bedding planes that can also form planes of weakness. In this work, we present a homogenization framework for modeling inelastic layered media. The proposed constitutive model allows for distinct micro-constitutive laws for each layer, explicit representation of layer distributions, as well as incorporation of imperfect bonding at the interface between adjacent layers. No a priori assumptions are needed regarding the specific constitutive models used for the layers and interfaces, providing significant modeling flexibility. The overall framework provides a simple and physically-motivated way of defining anisotropic material behavior as an emergent property of the layered microstructure. The model is calibrated using triaxial and true-triaxial experimental data to demonstrate its ability to describe anisotropic deformation and multiple modes of failure.

58 GEOSCIENCES↗

A new approach to the design of surface subsystems of polymeric insulators for HV and MV apparatus under AC voltage

The design of high voltage and medium voltage AC and DC standoff insulators, and, in general, of insulation systems where surface and interface properties are predominant factors, is based on specifications and standards that rely upon long-term experiences and lab testing. Surface insulating properties depend on electrical and thermal stresses, besides environmental factors, and the inception of extrinsic ageing phenomena, such as partial discharges, can be already a cause of reduced reliability and premature failure (for organic insulating materials). An innovative approach, based on field simulation, discharge modelling, and partial discharge inception measurements is presented by the authors, which can establish a solid basis to optimise insulation design for any type of supply voltage waveform. This method, the three-leg approach, is applied here to a cable system under AC sinusoidal voltage, but it can work for any type of insulation system, such as bushings, switch gears, transformers, rotating machines, and power electronics boards.

42 ENGINEERING↗

Evaluating Admittance Relaying for Inverter-Interfaced Microgrid Protection [Slides]

Admittance protection with current compensation is viable for inverter-interfaced microgrids. A downside is that pilot relaying is likely required given short line lengths & change in system configuration from switching – operating area will be large compared to the line impedance. If a communications channel is required, there are more sophisticated methods such as state-estimation based protection that can operate with the failure of one or more sensors.

42 ENGINEERING↗

RAMI Analysis for Designing and Optimizing Tokamak Cooling Water System (TCWS) for the ITER's Fusion Reactor

U.S.-ITER is responsible for the design, engineering, and procurement of the Tokamak Cooling Water System (TCWS). TCWS is designed to provide cooling and baking for client systems that include the first wall/blanket, vacuum vessel, divertor, and neutral beam injector. Additional operations that support these primary functions include chemical control of water provided to client systems, draining and drying for maintenance, and leak detection/localization. TCWS interfaces with 27 systems including the secondary cooling system, which rejects this heat to the environment. TCWS transfers heat generated in the Tokamak during nominal pulsed operation - 850 MW at up to 150 C and 4.2 MPa water pressure. Impurities are diffused from in-vessel components and the vacuum vessel by water baking at 200-240 C at up to 4.4 MPa. TCWS is complex because it serves vital functions for four primary clients whose performance is critical to ITER's success and interfaces with more than 20 additional ITER systems. Conceptual design of this one-of-a-kind cooling system has been completed; however, several issues remain that must be resolved before moving to the next stage of the design process. The 2004 baseline design indicated cooling loops that have no fault tolerance for component failures. During plasma operation, each cooling loop relies on a single pump, a single pressurizer, and one heat exchanger. Consequently, failure of any of these would render TCWS inoperable, resulting in plasma shutdown. The application of reliability, availability, maintainability, and inspectability (RAMI) tools during the different stages of TCWS design is crucial for optimization purposes and for maintaining compliance with project requirements. RAMI analysis will indicate appropriate equipment redundancy that provides graceful degradation in the event of an equipment failure. This analysis helps demonstrate that using proven, commercially available equipment is better than using custom-designed equipment with no field experience and lowers specific costs while providing higher reliability. This paper presents a brief description of the TCWS conceptual design and the application of RAMI tools to optimize the design at different stages during the project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of Laser Fluence on Microstructure and Bonding Characteristics of Wideband Laser-Deposited Nickel Composite Coatings

The wideband laser has shown great potential in metal–ceramic coatings deposition due to the high efficiency and low dilution rate. However, the effects of wideband laser process on microstructure evolution and bonding mechanism at the coatings/substrate interface are still a critical problem and need further investigation. In this work, nickel composite coatings are fabricated on the surface high-strength low-alloy steel. The effects of laser fluence on microstructure evolution, shear strength and fracture mechanism are studied. Results indicated the added WC particles were partly dissolved due to the high-power laser irradiation. Many block precipitates and dense eutectic were synthesized in composite coatings. Reinforced phases mainly consist of Cr{sub 5}B{sub 3}, Cr{sub 23}C{sub 6}, W{sub 2}C and Cr{sub 3}Ni{sub 2}. The dilution of Q550 steel contributed to the formation of nickel dendrites and facilitated a dense metallurgical bonding at coating/substrate interface when laser fluence was high. Shear strength tests indicated the laser fluence and shear strength had a positive correlation. For Ni60/WC composite coatings designed in these experiments, the recommend laser fluence should be higher than 55 J/mm{sup 2}, above which the shear strength could be greater than 200 MPa. Fracture surfaces indicated the failure mechanism of composite coatings was quasi-cleavage fracture.

36 MATERIALS SCIENCE↗

High performance anode for advanced Li batteries

The overall objective of this Phase I SBIR effort was to advance the manufacturing technology for ASI’s Si-CNF high-performance anode by creating a framework for large volume production and utilization of low-cost Si-coated carbon nanofibers (Si-CNF) for the battery industry. This project explores the use of nano-structured silicon which is deposited on a nano-scale carbon filament to achieve the benefits of high cycle life and high charge capacity without the consequent fading of, or failure in the capacity resulting from stress-induced fracturing of the Si particles and de-coupling from the electrode. ASI’s patented coating process distinguishes itself from others, in that it is highly reproducible, readily scalable and results in a Si-CNF composite structure containing 25-30% silicon, with a compositionally graded interface at the Si-CNF interface that significantly improve cycling stability and enhances adhesion of silicon to the carbon fiber support. In Phase I, the team demonstrated the production of the Si-CNF anode material can successfully be transitioned from a static bench-scale reactor into a fluidized bed reactor. In addition, ASI made significant progress in the development of low cost, quick testing methods which can be performed on silicon coated CNFs as a means of quality control. To date, weight change, density, and cycling performance were the key metrics used to validate the high performance anode material. Under this effort, ASI made strides to establish a quality control protocol for the large volume production of Si-CNFs and has identified several key technical thrusts for future work. Using the results of this Phase I effort as a foundation, ASI has defined a path forward to commercialize and deliver high volume and low-cost production of SI-CNF material for anodes in Li-ion batteries.

25 ENERGY STORAGE↗

On the Feasibility of Tailoring Copper–Nickel Functionally Graded Materials Fabricated through Laser Metal Deposition

In this study, pulse-width modulation of laser power was identified as a feasible means for varying the chemical gradient in copper–nickel-graded materials. Graded material deposits of 70 wt. %. copper-30 wt. %. nickel on 100 wt. %. nickel and vice versa were deposited and characterized. The 70/30 copper–nickel weight ratio in the feedstock powder was achieved through blending elemental copper and 96 wt. %. Ni–Delero-22 alloy. At the dissimilar material interface over the course of four layers, the duty cycle of power was ramped down from a high value to optimized deposition conditions. This change was theorized to influence the remelting and deposition height, and by extension, vary the chemistry gradient. X-ray Energy Dispersive Spectroscopy (EDS) analysis showed significant differences in the span and nature of chemistry gradient with varying duty cycles. These observations were also supported by the variation in microhardness values across the interface. The influence of different chemistry gradients on the tensile performance was observed through mini-tensile testing, coupled with Digital Image Correlation (DIC). The strain fields from the DIC analysis showed variations in strain for different chemistry gradients. The strength measurements from these specimens were also different for different chemistry gradients. The site of failure was observed to always occur within the copper-rich region.

36 MATERIALS SCIENCE↗

Verification and Validation of Systems in which AI is a Key Element

Many systems are being considered in which artificial intelligence (AI) will be a key element. Failure of an AI element can lead to system failure, hence the need for AI verification and validation (V&V). This article addresses V&V of such a system, focusing on the issues created by characteristics of AI that make V&V challenging. The element(s) containing AI capabilities is treated as a subsystem and V&V is conducted on that subsystem and its interfaces with other elements of the system under study, just as V&V would be conducted on other subsystems. That is, the high-level definitions of verification and of validation do not change for systems containing one or more AI elements. However, AI V&V challenges require approaches and solutions beyond those for conventional or traditional (those without AI elements) systems. This article provides an overview of how machine learning components/subsystems “fit” in the systems engineering framework (Section 1), identifies characteristics of AI subsystems that create challenges in their V&V (Section 2), describes those challenges (Section 3) and provides some potential solutions (Section 4).

Pullum, Laura↗

2nd World Congress on Integrated Computational Materials Engineering, Part II: Process Optimization: Multi-Objective Optimization of Microstructure in Wrought Magnesium Alloys.

The microstructural features that govern the mechanical properties of wrought magnesium alloys include grain size, crystallographic texture, and twinning. Several processes based on shear deformation have been developed that promote grain refinement, weakening of the basal texture, as well as the shift of the peak intensity away from the center of the basal pole figure — features that promote room temperature ductility in Mg alloys. At ORNL, we are currently exploring the concept of introducing nano-twins within sub-micron grains as a possible mechanism for simultaneously improving strength and ductility by exploiting a potential dislocation glide along the twin-matrix interface — a mechanism that was originally proposed for face-centered cubic materials. Specifically, we have developed an integrated modeling and optimization framework in order to identify the combinations of grain size, texture and twin spacing that can maximize strength-ductility combinations. A micromechanical model that relates microstructure to material strength is coupled with a failure model that relates ductility to a critical shear strain and a critical hydrostatic stress. The micro-mechanical model is combined with an optimization tool based on genetic algorithm. A multi-objective optimization technique is used to explore the strength-ductility space in a systematic fashion and identify optimum combinations of the microstructural parameters that will simultaneously maximize the strength-ductility in the alloy.

crystal plasticity↗

Enabling Stable Cycling of 4.2 V High-Voltage All-Solid-State Batteries with PEO-Based Solid Electrolyte

Poly(ethylene oxide) (PEO)-based solid electrolytes are expected to be exploited in solid-state batteries with high safety. Its narrow electrochemical window, however, limits the potential for high voltage and high energy density applications. In this paper, the electrochemical oxidation behavior of PEO and the failure mechanisms of LiCoO 2 -PEO solid-state batteries are studied. It is found that although for pure PEO it starts to oxidize at a voltage of above 3.9 V versus Li/Li + , the decomposition products have appropriate Li + conductivity that unexpectedly form a relatively stable cathode electrolyte interphase (CEI) layer at the PEO and electrode interface. The performance degradation of the LiCoO 2 -PEO battery originates from the strong oxidizing ability of LiCoO 2 after delithiation at high voltages, which accelerates the decomposition of PEO and drives the self-oxygen-release of LiCoO 2 , leading to the unceasing growth of CEI and the destruction of the LiCoO 2 surface. When LiCoO 2 is well coated or a stable cathode LiMn 0.7 Fe 0.3 PO 4 is used, a substantially improved electrochemical performance can be achieved, with 88.6% capacity retention after 50 cycles for Li 1.4 Al 0.4 Ti 1.6 (PO 4 ) 3 coated LiCoO 2 and 90.3% capacity retention after 100 cycles for LiMn 0.7 Fe 0.3 PO 4 . The results suggest that, when paired with stable cathodes, the PEO-based solid polymer electrolytes could be compatible with high voltage operation.

25 ENERGY STORAGE↗