Search NASA⌕ Search

SEARCH · Search NASA

Results for “lab testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A New Family of Proton‐Conducting Electrolytes for Reversible Solid Oxide Cells: BaHf x Ce 0.8− x Y 0.1 Yb 0.1 O 3− δ

Abstract Reversible solid oxide cells based on ceramic proton conductors have potential to be the most efficient system for large‐scale energy storage. The performance and long‐term durability of these systems, however, are often limited by the ionic conductivity or stability of the proton‐conducting electrolyte. Here new family of solid oxide electrolytes, BaHf x Ce 0.8− x Y 0.1 Yb 0.1 O 3− δ (BHCYYb), which demonstrate a superior ionic conductivity to stability trade‐off than the state‐of‐the‐art proton conductors, BaZr x Ce 0.8− x Y 0.1 Yb 0.1 O 3− δ (BZCYYb), at similar Zr/Hf concentrations, as confirmed by thermogravimetric analysis, Raman, and X‐ray diffraction analysis of samples over 500 h of testing are reported. The increase in performance is revealed through thermodynamic arguments and first‐principle calculations. In addition, lab scale full cells are fabricated, demonstrating high peak power densities of 1.1, 1.4, and 1.6 W cm −2 at 600, 650, and 700 °C, respectively. Round‐trip efficiencies for steam electrolysis at 1 A cm −2 are 78%, 72%, and 62% at 700, 650, and 600 °C, respectively. Finally, CO 2 H 2 O electrolysis is carried out for over 700 h with no degradation.

Murphy, Ryan↗
DOE OSTI2022

Pressure drop and heat transfer characteristics of nitrate salt and supercritical CO 2 in a diffusion-bonded heat exchanger

A lab-scale 316/L stainless steel diffusion-bonded heat exchanger was examined within a coupled high-temperature test facility consisting of an atmospheric-pressure nitrate salt loop and a supercritical carbon dioxide (sCO 2 ) loop operating between 10 and 16 MPa. Pressure loss measurements collected for flow rates up to 0.55 kg/s of Solar Salt and up to 0.6 kg/s of carbon dioxide were used to generate friction factor correlations for the respective circular and semicircular zig-zag flow passages. Heat transfer measurements were also performed over a wide range of conditions to produce Nusselt correlations for the CO 2 and nitrate salt geometries. The Nusselt number is deduced from a heat transfer resistance network and overall conductance measurements collected across the operating envelope of the coupled sCO 2 – nitrate salt test facility. The CO 2 side correlation showed excellent agreement with existing correlations in the literature. Further, the salt side, having nearly circular channels with a different zig-zag angle and hydraulic diameter, yielded a new correlation applicable to the laminar flow regime. To examine the similitude of the friction correlations, pressure drop testing with water was performed on both sides of the component as well. Finally, results from non-destructive examination are discussed to provide insights regarding inspection methods and draining performance of high-temperature liquids in compact heat exchangers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Laser Diode Analysis and Verification (Professional Report)

The goal of this project at Lawrence Livermore National Laboratory (LLNL) was focused on analyzing and verifying laser diodes to ensure that the diodes meet requirements for LLNL mission applications. The different stages of this testing were documented in a process flow map which included location color coding so that each step was clearly defined in scope and location of appropriate testing facility. Data were collected and analyzed and compared to minimum acceptable values to see if requirements were met. The process map documents the initial receipt, inspection, and testing of the laser diodes. Initial inspections started with Keyence Microscope imaging and then moved on to High Potential, Ramp, and Burst Testing. Data from the diode testing were processed through MATLAB and Python codes to verify various metrics such as slope efficiency, threshold current, back irradiance, and beam divergence met requirements. These metrics were then recorded in Excel summary reports. Approximately 95% of the laser diodes passed all tests. Presentations were given to Lawrence Livermore’s internal leadership team, an external partner, and to a Lab-wide audience. The data released for this report was constrained by information protection considerations of LLNL’s national security missions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Review of Shock, Vibration, and Other Tests for Type IV Hydrogen Composite Pressure Vessels for Rail Use

Requirements specific to hydrogen rail transportation and its unique components are currently not well represented in safety codes and standards. Notably, one of the most important components of the system, the hydrogen storage vessel, may be subject to entirely different shock and vibration conditions compared to hydrogen tanks on road vehicles. This report focuses on how composite hydrogen tanks are tested for performance and how this may relate to these tanks being used on rail systems. The shock and vibration testing procedures that are relevant for hydrogen composite tanks used for rail applications have been identified, as well as some general testing requirements for hydrogen tanks and composite tanks.

42 ENGINEERING↗
DOE OSTI2020

SLAC joins the global fight against COVID-19

The lab is responding to the coronavirus crisis by imaging disease-related biomolecules, developing standards for reliable coronavirus testing and enabling other essential research.

Gnida, Manuel↗
DOE OSTI2022

A Strong-QCD Regime Measurement of the Proton’s Spin Structure

The theory of the strong force, Quantum Chromodynamics (QCD) remains one of the most important ways to understand the fundamental properties of ordinary matter. However, at low momentum transfer Q 2 , in the regime where the strong force becomes extremely strong, our understanding of QCD for ordinary nucleons becomes hazy. Several cutting edge theories such as Chiral Perturbation Theory (χPT) and Lattice QCD have provided valuable predictions in this regime, but Lattice QCD has not yet extended predictions of many important quantities to this kinematic region, and Chiral Perturbation Theory has faced several important disagreements with experimental data for the neutron over the last several decades. It is therefore of extreme importance to have a benchmark of experimental data in the low energy regime for the proton’s behavior, as a test of leading theories for the behavior of QCD in this regime. The E08-027 (g2p) experiment ran at Jefferson Lab in 2012 with the goal of collecting this valuable data, and though I was still completing my undergraduate studies at the time, I became involved in the analysis in 2015 and built on the previous work to complete it and analyze the exciting results. This experiment achieved a high precision measurement of the spin structure functions g1 and g2 for the proton, quantities which describe the internal spin structure of the proton. These measurements were taken in the valuable low Q 2 region described above, and used to extract several moments of these spin structure functions which can be directly compared to the cutting-edge predictions of Chiral Perturbation Theory. Though the experiment’s timeline was such that I didn’t have a chance to work directly on the experimental setup, I had the opportunity to acquire hands-on experience working on a polarized target at UNH which is very similar to the crucial polarized target used in the g2p experiment. Full details of the g2p experiment and my experimental work at the University of New Hampshire are presented in this thesis, as well as a detailed description of the analysis process and the exciting benchmark results, which serve as a direct test of all current and future theories of QCD in the low-Q 2 regime.

Ruth, David↗
DOE OSTI2025

Insights into catalyst degradation during alkaline water electrolysis under variable operation

Energy conversion technologies that are key to decarbonization efforts face significant durability challenges due to variable operation. Understanding the impact of variable operation on catalytic stability and identifying the key variables that dictate degradation is crucial for developing robust technologies. Here, we present a comprehensive investigation of the effects of variable operation on liquid alkaline water electrolysis. Our findings reveal that variable operation induces severe degradation of Ni, Fe, and Co catalytic films that is not observed during steady-state operation. By systematically interrogating the electrode discharge during simulated shutdown tests using Raman spectroscopy and mass spectrometry techniques, we uncover significant alterations caused by reverse currents in real time. These include changes in crystal structure, composition, film thickness, electronic conductivity, and dissolution rates. Lab-scale electrolyzer experiments further highlight the impact of variable operation on catalyst materials under relevant conditions. Finally, we provide guidelines for leveraging these insights to advance electrocatalysis research. This work underscores the importance of integrating realistic stressors into stability testing and offers practical guidelines for catalyst design, performance evaluation, and industrial implementation. Collectively, insights from this study will drive the development of more resilient energy conversion technologies.

Marquez, Raul A. [Univ. of Texas, Austin, TX (Unit↗
DOE OSTI2021

Modeling of Glycolate Destruction in the Recycle Collection Tank

The Savannah River Site’s DWPF is being upgraded with the introduction of the NG flowsheet. Glycolic acid has been shown to be a superior alternative to formic acid for sludge processing. The new flowsheet improves or maintains necessary parameters such as 1) reduction of mercury, 2) adjustment of feed rheology, 3) pH stability, and 4) adjustment of melter oxidation/reduction potential. Further, the use of glycolic acid virtually eliminates the potential for catalytic hydrogen generation in DWPF processing DWPF process condensates are collected and returned to the Savannah River Site (SRS) CSTF. The RCT collects off-gas condensate during chemical processing, vitrification, and other unit operations performed in DWPF and is the singular return vessel delivering recycle effluent back to CSTF. Each batch of recycle will have a small amount of glycolate from chemical processing and melter off-gas condensates. To avoid potential flammability issues due to thermolysis of glycolate in the CSTF, Savannah River National Laboratory (SRNL) provided to Savannah River Remediation (SRR) at their request a Task Technical and Quality Assurance Plan (TTQAP) to quantify and mitigate glycolate returns via DWPF’s recycle stream. The request included testing of a process to oxidize glycolate and other organic species that are responsible for hydrogen generation from thermolysis. Following that work SRR provided a Task Technical Request (TTR) that requested process modeling. In 2021 a TTQAP was issued to cover the modeling work. Modeling draws data from laboratory scale studies using chemical simulants and radioactive waste samples. Chemical kinetic modeling was performed to evaluate the feasibility of using sodium permanganate to destroy glycolate in the RCT. The results from the laboratory studies were summarized in a series of reports. Reference 9 is a report of lab scale processing of actual DWPF Slurry Mix Evaporate Condensate Tank (SMECT) and Offgas Condensate Tank (OGCT) samples in the SRNL Shielded Cells. Tests at caustic conditions demonstrated sodium permanganate was effective in converting glycolate to oxalate, and permanganate (Mn 7+ ) is reduced to manganate (Mn 6+ ) with no significant formation of carbon dioxide or carbonate. Equation (1) was found to best describe the observed reaction of glycolate with permanganate under nominal (60 to 145 mg/L in RCT) glycolate entrainment conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Evaluation of the interfacial bonding strength between hafnia and silica layers deposited by electron-beam evaporation

Factors contributing to the mechanical strength of multilayer optical coatings involving alternating layers of electron-beam evaporated hafnia and silica is investigated. It is observed that upon rupture resulting from nanosecond laser damage, fragments consisting of layer pairs are produced. These pairs are formed as a result of a strong asymmetry in adhesion strength between interfaces, leading to preferential delamination at interfaces where silica is deposited on hafnia, and not the reverse, despite the fact that both interface types consist of the same pair of materials. The observed disparity in adhesion strength was further studied using nanomechanical scratch tests, revealing loads at which fracture occurs, and fracture morphology, both of which are highly dependent on deposition order. Based on these measurements, along with the morphological analysis of the nanostructure of the coatings, we conclude that the surface microstructure in each coating layer affects its adhesion strength with the succeeding layer. The findings outlined here are particularly relevant to the production of large aperture, high-performance optics designed for use in next-generation lasers.

adhesion strength↗
DOE OSTI2023

Boosting the interfacial superionic conduction of halide solid electrolytes for all-solid-state batteries

Designing highly conductive and (electro)chemical stable inorganic solid electrolytes using cost-effective materials is crucial for developing all-solid-state batteries. Here, we report halide nanocomposite solid electrolytes (HNSEs) ZrO 2 (-ACl)-A 2 ZrCl 6 (A = Li or Na) that demonstrate improved ionic conductivities at 30 °C, from 0.40 to 1.3 mS cm -1 and from 0.011 to 0.11 mS cm -1 for Li + and Na + , respectively, compared to A 2 ZrCl 6 , and improved compatibility with sulfide solid electrolytes. The mechanochemical method employing Li 2 O for the HNSEs synthesis enables the formation of nanostructured networks that promote interfacial superionic conduction. Via density functional theory calculations combined with synchrotron X-ray and 6 Li nuclear magnetic resonance measurements and analyses, we demonstrate that interfacial oxygen-substituted compounds are responsible for the boosted interfacial conduction mechanism. Compared to state-of-the-art Li 2 ZrCl 6 , the fluorinated ZrO 2 -2Li 2 ZrCl 5 F HNSE shows improved high-voltage stability and interfacial compatibility with Li 6 PS 5 Cl and layered lithium transition metal oxide-based positive electrodes without detrimentally affecting Li + conductivity. We also report the assembly and testing of a Li-In||LiNi 0.88 Co 0.11 Mn 0.01 O 2 all-solid-state lab-scale cell operating at 30 °C and 70 MPa and capable of delivering a specific discharge of 115 mAh g -1 after almost 2000 cycles at 400 mA g -1 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Performance of photosensors in a high-rate environment for gas Cherenkov detectors

We report the solenoidal large intensity device (SoLID) at Jefferson Lab will push the boundaries of luminosity for a large-acceptance detector, which necessitates the use of a light-gas threshold Cherenkov counter for online event selection. Due to the high luminosity, the single-photon background rate in this counter can exceed 160 kHz/cm 2 at the photosensors. Therefore, it is essential to validate the high-rate limits of the planned photosensors and readout electronics in order to mitigate the risk of failure. We report on the design and an early set of studies carried out using a small Cherenkov counter in a high-rate environment up to 60 kHz/cm 2 , in Hall C at Jefferson Lab. Commercially available multi-anode photomultipliers (MaPMT) and low-cost large-area picosecond photodetectors (LAPPD) were tested using the JLab FADC250 modules for readout. The test beam results show that the MaPMT array and the internal stripline LAPPD can detect and identify single-electron and pair-production events in high-rate environments. Due to its higher quantum efficiency, the MaPMT array provided a better separation between the single-electron and the pair-production events compared to the internal stripline LAPPD. A GEANT4 simulation confirms the beam test performance of our counter device.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Aerial Crosspolarized NQR-NMR: Buried Explosive Detection From a Safe Distance

Nuclear quadrupole resonance is a non-destructive detection and inspection technique with potential as a non-destructive test (NDT) tool. Establishment of the capability opens the door to its use in furthering the mission of the labs. There are many possible uses of the capability: explosive detection and stress/strain detection in epoxies are two of the more obvious and are the main results of this work. Enhancement of the signal-to-noise ratio (SNR) and improvements in the acquisition time of the experiment were key focuses of this work. These were achieved by combing special spin-lock pulse sequences with cross-polarization (CP) schemes to improve the signals with shorter acquisition times. A novel rotating magnetic field device was created to facilitate CP in the field. Implementation of these schemes provided a significant reduction in SNR/time.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Recent Advanced Reactor Multiphysics Model Highlights in the Virtual Test Bed (VTB)

The Virtual Test Bed (VTB) host over 30 distinct simulations that showcase state-of-the art capabilities across the national lab complex. An update on the status of models on the VTB is summarized here, along with a more detailed overview of select recent new capabilities to showcase. All of the major advanced reactor types are represented in the VTB. The first example consists of a multiphysics simulation to track the transport of species in Molten Salt Reactors using depletion, advection, and thermochemical calculations. The second consists of a coupled neutronic and thermal hydraulic simulation to validate a gas cooled reactor. The third consist of pebble-bed equilibrium model for a fluoride high-temperature reactor. The fourth is a high-fidelity neutronic and thermal hydraulic model of a liquid metal reactor assembly. And lastly the fifth consists of transient multiphysics simulations of heat pipe microreactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

HE Production Update at JLab - Introducing an Enhanced Nitrogen Purge for Clean String Assembly

A major limitation to cryomodule performance is field emission caused by particulates within the superconducting cavities. To reduce contamination of the inner surfaces during assembly in a cleanroom, the whole string can be connected to a purge system, which maintains a constant overpressure of dry, clean nitrogen gas. Following successes of similar systems at XFEL and Fermilab, Jefferson Lab followed this example for the production of LCLS-II HE cryomodules. Implementing this system required new procedures, infrastructure, and hardware, as well as significant testing of the system before production began. This paper will summarize the implemented controls and procedures, including lessons learned from Fermilab, as well as the results of mock-up tests. Based on the latter, the system was used to assemble the first article string in April 2022, and was also used during a rework required due to issues with cold FPC ceramics two months later. The benefits of using a purge system with regards to procedure, time savings, and added flexibility for potential rework have already proven to provide a significant improvement for the production of LCLS-II-HE cryomodules at Jefferson Lab.

Owen, P. D.↗
DOE OSTI2022

A Blockchain Based Co-Simulation Framework for Integrating DERs into Wholesale Electricity Markets

As the number of distributed energy resources (DERs) continue to increase across energy-delivery systems, there remains a need for integrating their capabilities into traditional grid operations. In this paper, a blockchain-based solution is proposed to facilitate FERC's Order No. 2222 implementations. The presented use-case enables small-scale DERs to participate in wholesale market operations through DER aggregators, while also enabling local distribution system operators to enforce distribution system constraints in a secure and traceable manner. The presented use case is built around the Unified Testing Platform (UTP) being developed as a part of the Blockchain for Optimized Security and Energy Management (BLOSEM) project. This is a multi-lab effort intended to simplify the deployment of blockchain-powered grid solutions by enabling the integration of simulation tools, and blockchain technologies through the use of system-agnostic interfaces that provide a modular, interoperable, and reusable connectivity layer.

blockchain testing↗
DOE OSTI2022

A Blockchain Based Co-Simulation Framework for Integrating DERs to Wholesale Electricity Markets: Preprint

As the number of distributed energy resources (DERs) continue to increase across energy-delivery systems, there remains a need for integrating their capabilities into traditional grid operations. In this paper, a blockchain-based solution is proposed to facilitate FERC's Order No. 2222 implementations. The presented use-case enables small-scale DERs to participate in wholesale market operations through DER aggregators, while also enabling local distribution system operators to enforce distribution system constraints in a secure and traceable manner. The presented use case is built around the Unified Testing Platform (UTP) being developed as a part of the Blockchain for Optimized Security and Energy Management (BLOSEM) project. This is a multi-lab effort intended to simplify the deployment of blockchain-powered grid solutions by enabling the integration of simulation tools, and blockchain technologies through the use of system-agnostic interfaces that provide a modular, interoperable, and reusable connectivity layer.

blockchain testing↗
DOE OSTI2025

Ammonium-coordinated exchanger (ACE) functionalized silica sorbents for recovering/removing aqueous anionic contaminants

There are limited studies of functionalized silica anion exchange sorbents used for critical/heavy metal recovery/removal relative to polymeric and other inorganic materials. This work features ammonium-coordinated exchanger (ACE) anion exchange particle sorbents prepared by either acid-washing epoxy-crosslinked polyethylenimine (PEI) hydrogen bonded within/to a silica particle sorbent (two-step method) or reacting a di-chlorinated crosslinker, α,α-dichloro-p-xylene (DPX), with PEI within silica (single-step method). Energy dispersive X-ray spectroscopy (EDS) and infrared spectroscopy confirmed the presence of -NH 2 + ···Cl - and -NH 3 + ···Cl - groups, which removed oxyanionic species –arsenate, selenate, chromate, sulfate, phosphate, and nitrate– plus bromide from ideal solutions, authentic acid mine drainage (AMD), and authentic flue gas desulfurization (FGD) wastewater. Affinity of the anions for ACE varied across single- and mixed-element solutions. However, affinity for CrO 4 2- was among the highest in both cases. Total anion uptake by the optimized ACE, PEI-E3-HCl_1.1, reached 1.2 mmol anion/g-sorb. (0.56 mmol CrO 4 2- /g), or ∼2.3 mmol negative charge/g-sorb. This was close to the 0.52 mmol CrO 4 2- /g of a commercial anion exchange resin. Near-consistent removal of 20–80 % of each anion from FGD during an eight-cycle adsorption-desorption (1 M NaCl) test predicted good ACE viability for testing under practical conditions at larger scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗