Search NASA⌕ Search

SEARCH · Search NASA

Results for “layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Separation behavior of boundary layers on three-dimensional wings

An inverse boundary layer procedure for calculating separated, turbulent boundary layers at infinitely long, crabbing wing was developed. The procedure was developed for calculating three dimensional, incompressible turbulent boundary layers was expanded to adiabatic, compressible flows. Example calculations with transsonic wings were made including viscose effects. In this case an approximated calculation method described for areas of separated, turbulent boundary layers, permitting calculation of this displacement thickness. The laminar boundary layer development was calculated with inclined ellipsoids.

Stock, H. W.↗
NASA NTRS1981

Computation of unsteady turbulent boundary layers with flow reversal and evaluation of two separate turbulence models

A procedure which solves the governing boundary layer equations within Keller's box method was developed for calculating unsteady laminar flows with flow reversal. This method is extended to turbulent boundary layers with flow reversal. Test cases are used to investigate the proposition that unsteady turbulent boundary layers also remain free of singularities. Turbulent flow calculations are performed. The governing equations for both models are solved. As in laminar flows, the unsteady turbulent boundary layers are free from singularities, but there is a clear indication of rapid thickening of the boundary layer with increasing flow reversal. Predictions of both turbulence models are the same for all practical purposes.

Cebeci, T.↗
NASA NTRS1980

Turbulent boundary layer heat transfer experiments: Convex curvature effects, including introduction and recovery

Heat transfer rates were measured through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20-50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15-20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: (1) the effect of initial boundary layer thickness; (2) the effect of freestream velocity; (3) the effect of freestream acceleration; (4) the effect of unheated starting length; and (5) the effect of the maturity of the boundary layer. Regardless of the initial state, curvature eventually forced the boundary layer into an asymptotic curved condition. The slope, minus one, is believed to be significant.

Simon, T. W.↗
NASA NTRS1981

Dynamic behavior of an unsteady trubulent boundary layer

Experiments on an unsteady turbulent boundary layer are reported in which the upstream portion of the flow is steady (in the mean) and in the downstream region, the boundary layer sees a linearly decreasing free stream velocity. This velocity gradient oscillates in time, at frequencies ranging from zero to approximately the bursting frequency. For the small amplitude, the mean velocity and mean turbulence intensity profiles are unaffected by the oscillations. The amplitude of the periodic velocity component, although as much as 70% greater than that in the free stream for very low frequencies, becomes equal to that in the free stream at higher frequencies. At high frequencies, both the boundary layer thickness and the Reynolds stress distribution across the boundary layer become frozen. The behavior at higher amplitude is quite similar. At sufficiently high frequencies, the boundary layer thickness remains frozen at the mean value over the oscillation cycle, even though flow reverses near the wall during a part of the cycle.

Parikh, P. G.↗
NASA NTRS1981

Modification in drag of turbulent boundary layers resulting from manipulation of large-scale structures

The effects of placing a parallel-plate turbulence manipulator in a boundary layer are documented through flow visualization and hot wire measurements. The boundary layer manipulator was designed to manage the large scale structures of turbulence leading to a reduction in surface drag. The differences in the turbulent structure of the boundary layer are summarized to demonstrate differences in various flow properties. The manipulator inhibited the intermittent large scale structure of the turbulent boundary layer for at least 70 boundary layer thicknesses downstream. With the removal of the large scale, the streamwise turbulence intensity levels near the wall were reduced. The downstream distribution of the skin friction was also altered by the introduction of the manipulator.

Corke, T. C.↗
NASA NTRS1980

Langmuir probe measurements of double-layers in a pulsed discharge

Langmuir probe measurements have been carried out which confirm the occurrence of double-layers in an argon positive column. Pulsing the discharge current permitted probe measurements to be performed in the presence of the double-layer. Supplementary evidence, obtained from dc and pulsed discharges, indicated that the double-layers formed in the two modes of operation were similar. The double-layers observed were weak and stable; their relation to other classes of double-layers is discussed, and directions for future work are suggested.

Levine, J. S.↗
NASA NTRS1981

Kelvin-Helmholtz instability in the magnetopause-boundary layer region

The Kelvin-Helmholtz instability in the magnetopause-boundary layer region is studied on the basis of an idealized model which consists of three uniform plasma regions: the magnetosheath, the boundary layer, and the magnetosphere. There are two unstable modes in the magnetopause-boundary layer region: one is excited at the magnetopause (the magnetopause mode) and the other is excited at the inner surface of the boundary layer (the inner mode). The inner mode is found to be unstable most of the time, while the excitation of the magnetopause mode depends on the magnetic field in the magnetosheath. The observed variation of the boundary layer thickness can be attributed to the unstable inner mode. Possible relationships between the Pc 3-5 geomagnetic pulsations and the surface waves excited on the magnetospheric boundary are also discussed.

Lee, L. C.↗
NASA NTRS1981

Development of energy-absorbing reaction-sintered Si3N4 surface layers on hot-pressed Si3N4

Energy-absorbing Si3N4 surface layers on dense Si3N4 substrates were formed by in-place nitridation of fine-grained silicon powder. Ballistic impact tests performed on samples with 1-mm thick layers at room temperature and 1370 C showed up to an eightfold increase in the energy necessary to fracture the substrate. For maximum impact resistance, a small amount (about 20 vol %) of residual Si must be present in the reaction-sintered Si3N4 surface layer. Thermal cycling to 1370 C did not affect impact resistance, even though a considerable amount of SiO2 formed within the reaction-sintered Si3N4 layer during cycling. Erosion testing of samples in a Mach 0.8 burner rig at 1370 C resulted in minimal surface recession of the surface layer. Chemically vapor-deposited SiC-coated material similarly tested exhibited no surface recession.

Brennan, J. J.↗
NASA NTRS1981

Boundary layer thermal stresses in angle-ply composite laminates, part 1

Thermal boundary-layer stresses (near free edges) and displacements were determined by a an eigenfunction expansion technique and the establishment of an appropriate particular solution. Current solutions in the region away from the singular domain (free edge) are found to be excellent agreement with existing approximate numerical results. As the edge is approached, the singular term controls the near field behavior of the boundary layer. Results are presented for cases of various angle-ply graphite/epoxy laminates with (theta/-theta/theta/theta) configurations. These results show high interlaminar (through-the-thickness) stresses. Thermal boundary-layer thicknesses of different composite systems are determined by examining the strain energy density distribution in composites. It is shown that the boundary-layer thickness depends on the degree of anisotropy of each individual lamina, thermomechanical properties of each ply, and the relative thickness of adjacent layers. The interlaminar thermal stresses are compressive with increasing temperature. The corresponding residual stresses are tensile and may enhance interply delaminations.

Wang, S. S.↗
NASA NTRS1982

Ordered mixed-layer structures in the Mighei carbonaceous chondrite matrix

High resolution transmission electron microscopy of the Mighei carbonaceous chondrite matrix has revealed the presence of a new mixed layer structure material. This mixed-layer material consists of an ordered arrangement of serpentine-type (S) and brucite-type (B) layers in the sequence SBBSBB. Electron diffraction and imaging techniques show that the basal periodicity is approximately 17 A. Discrete crystals of SBB-type material are typically curved, of small size (less than 1 micron) and show structural variations similar to the serpentine group minerals. Mixed-layer material also occurs in association with planar serpentine. Characteristics of SBB-type material are not consistent with known terrestrial mixed-layer clay minerals. Evidence for formation by a condensation event or by subsequent alteration of pre-existing material is not yet apparent.

Mackinnon, I. D. R.↗
NASA NTRS1982

Dynamical features of moving double layers

Numerical simulations of the dynamics of double layers that form in response to an applied potential drop across a plasma are carried out for plasmas of lengths much greater than previously considered. The evolution of finite-size plasmas of lengths 100, 200 and 400 Debye lengths at the low-potential end of the simulation region was followed by the solution of the Vlasov and Poisson equations. Results show that the double layer moves towards the high-potential side of the layer, at a speed directly dependent on the length of the plasma. The moving double layer is accompanied by a moving density front which is similar to an ion acoustic shock created by the expansion of a high-density plasma into a low-density plasma, as well as plasma heating and evacuation, electron and ion current interruptions and recovery. Double layer formation, motion, and accompanying phenomena are found to repeat periodically. Results are in good agreement with laboratory experiments, and may be used to explain certain phenomena observed in auroral plasmas.

Singh, N.↗
NASA NTRS1982

Boundary-layer effects in composite laminates. I - Free-edge stress singularities. II - Free-edge stress solutions and basic characteristics

The fundamental nature of the boundary-layer effect in fiber-reinforced composite laminates is formulated in terms of the theory of anisotropic elasticity. The basic structure of the boundary-layer field solution is obtained by using Lekhnitskii's stress potentials (1963). The boundary-layer stress field is found to be singular at composite laminate edges, and the exact order or strength of the boundary layer stress singularity is determined using an eigenfunction expansion method. A complete solution to the boundary-layer problem is then derived, and the convergence and accuracy of the solution are analyzed, comparing results with existing approximate numerical solutions. The solution method is demonstrated for a symmetric graphite-epoxy composite.

Wang, S. S.↗
NASA NTRS1983

Effect of boundary layers on solid walls in three-dimensional subsonic wind tunnels

A linear method is developed which accounts for the effects of boundary layers on solid walls in subsonic three-dimensional wind tunnels. The streamwise gradient of the displacement thickness for a solid-wall boundary layer is expressed in terms of the von Karman momentum integral. The growth of the boundary layer due to the wall shearing stress is small compared to the variation caused by the model-induced pressure gradient. The viscous boundary condition can be expressed in terms of the edge velocity gradient and the gradient of the inviscid velocity potential function at the wall. Utilizing this analysis on the solid walls of several three-dimensional wind tunnel configurations shows that the most pronounced wall boundary-layer effect is on solid blockage for completely closed wind tunnels. For solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, while the lift interference factor at the model station does not depend on the boundary-layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Adcock, J. B.↗
NASA NTRS1983

Exit of boundary layer plasma from the distant magnetotail

It is pointed out that the boundary layer plasma must somehow leave the magnetospheric system. It is proposed that the boundary layers on the dawn and dusk flanks are continued into the far magnetotail, becoming joined together far downstream, still on closed magnetic field lines. Within the combined layer there would be a dusk to dawn electric field for antisunward convection (as is the case for the boundary layers on the dawn and dusk flanks nearer to the earth). It is suggested that the boundary layer flow is so massive that the flow itself can generate the right electric field for continued flow. Most of the plasma in the mantle over the polar caps would also be convected out in a similar manner, rather feeding the plasma sheet. There would be a stagnation point inside the magnetotail, with any boundary or mantle plasma diffusing earthward of this point becoming the plasma sheet. It is deduced that no steady state solution is possible.

Heikkila, W. J.↗
NASA NTRS1983

Magnetic structure of the boundary layer

While magnetospheric convection appears to be driven by both magnetic reconnection and the 'viscous' dragging of closed flux tubes acting in varying proportions but with reconnection predominating as a cause, the action of the closed flux tubes of the low latitude boundary layer seems to predominate in driving system 1 field aligned currents and discrete auroras. ISEE boundary layer data for the magnetic shear effects associated with field aligned currents has occasionally shown a reverse draping of boundary layer field lines whose cause may be plasma entry around the cusps, a north-south asymmetry in current flow to the polar regions, or magnetic reconnection at high latitudes. Boundary layer encounter character and distribution asymmetries suggest that the boundary layer and/or plasma mantle may differ substantially at the dawn and dusk sides of the magnetosphere, and that their properties may have seasonal dependencies.

Hones, E. W., Jr.↗
NASA NTRS1983

Evaluation of a surface panel method coupled with several boundary layer analyses

Three boundary layer models are interacted with an inviscid panel method to evaluate their capabilities to predict aerodynamic performance characteristics. These boundary layer models include two two-dimensional boundary layer models and one three-dimensional boundary layer model. Previously reported discrepancies between the transpiration and surface displacement inviscid boundary layer simulations are discussed and resolved. Results from each of the models are compared with experimental data.

Kjelgaard, S. O.↗
NASA NTRS1981

Dynamic behavior of an unsteady turbulent boundary layer

Experiments on an unsteady turbulent boundary layer are reported in which the upstream portion of the flow is steady (in the mean) and in the downstream region, the boundary layer sees a linearly decreasing free stream velocity. This velocity gradient oscillates in time, at frequencies ranging from zero to approximately the bursting frequency. For the small amplitude, the mean velocity and mean turbulence intensity profiles are unaffected by the oscillations. The amplitude of the periodic velocity component, although as much as 70 percent greater than that in the free stream for very low frequencies, becomes equal to that in the free stream at higher frequencies. At high frequencies, both the boundary layer thickness and the Reynolds stress distribution across the boundary layer become frozen. The behavior at higher amplitude is quite similar. At sufficiently high frequencies, the boundary layer thickness remains frozen at the mean value over the oscillation cycle, even though flow reverses near the wall during a part of the cycle. Previously announced in STAR as N81-28392

Parikh, P. G.↗
NASA NTRS1983

End-wall boundary layer measurements in a two-stage fan

Detailed flow measurements made in the casing boundary layer of a two-stage transonic fan are summarized. These measurements were taken at stations upstream of the fan, between all blade rows, and downstream of the last blade row. At the design tip speed of 429 m/sec the fan achieved a peak efficiency of 0.846 at a pressure ratio of 2.471. The boundary layer data were obtained at three weight flows at the design speed: one near choke flow, one near peak efficiency, and one near stall. Conventional boundary layer parameters were calculated from the data measured at each measuring station for each of the three flows. A classical two dimensional casing boundary layer was measured at the fan inlet and extended inward to approximately 15 percent of span. A highly three dimensional boundary layer was measured at the exit of each blade row and extended inward to approximately 10 percent of span. The steep radial gradient of axial velocity noted at the exit of the rotors was reduced substantially as the flow passed through the stators. This reduced gradient is attributed to flow mixing. The amount of flow mixing was reflected in the radial redistribution of total temperature as the flow passed through the stators. The data also show overturning of the tip flow at the stator exits that is consistent with the expected effect of the secondary flow field. The blockage factors calculated from the measured data show an increase in blockage across the rotors and a decrease across the stators.

Ball, C. L.↗