Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Geomechanical characterization of Rock Valley carbonates

In Rock Valley, Nevada, the USA, past earthquake sequences and shallow faulting in Paleozoic carbonates remain poorly understood. Carbonates are typically more ductile rocks that do not experience large stress drops or fracture coalescence, which contradicts previous observations in the region. As part of the Source Physics Experiment, an effort has been made to experimentally characterize the petrophysical and geomechanical properties of carbonates from Rock Valley. Well core and outcrop samples were used to determine the difference between shallow-buried Tertiary limestones and deeply buried Paleozoic limestones and dolostones. The carbonates possessed porosities between 3 and 9%, with V P and V S in the Tertiary carbonates around 2700 and 1800 m/s, respectively, and 6000 and 3100 m/s, respectively, in the Paleozoic carbonates. Microstructural characterization revealed that the Paleozoic carbonates contained significantly more pre-existing damage and alteration than the Tertiary carbonates, though the deformation varies from localized to diffuse. Unconfined Brazilian tests and triaxial tests with confining pressures between 0 and 50 MPa showed that, although samples all experienced failure, the dolostones typically failed at greater stresses and possessed greater E/ν ratios than the limestones. Furthermore, the Hoek–Brown failure criterion was used to construct failure envelopes with the compressive and tensile failure tests. Velocity, density, and porosity measurements were used to construct a hypothetical velocity-depth profile and compare the results with the theoretical petrophysical measurements. Using brittleness analysis, the likely failure conditions were determined to be low-porosity dolomitic rock for fault nucleation in the Paleozoic basement.

Brittleness↗

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Heat Treatment on Microstructure and Mechanical Properties of Extruded Mg-4Zn-1.5Al-2Sn Alloy

The microstructure and mechanical properties of extruded Mg-4Zn-1.5Al-2Sn (ZAT422) alloy under different heat treatments were investigated by optical microscopy, scanning electron microscopy, x-ray diffraction, transmission electron microscopy, micro-hardness tests, and tensile tests. The results show that the as-extruded and heat-treated ZAT422 alloys mainly consisted of α-Mg and Mg{sub 2}Sn, and no ternary phase was detected. After aging, the amount of secondary phase precipitates increased significantly and the mechanical properties were improved. Among all the heat treatments, T5 heat treatment at 150 °C for 25 h resulted in the best combination of strength and ductility for ZAT422 alloy. The ultimate tensile strength, yield strength, and elongation (ε{sub f}) were found to be 290, 182 MPa, and 20%, respectively. Based on microstructural characterization, the variations in mechanical properties of the alloy subjected to heat treatment were analyzed in detail.

36 MATERIALS SCIENCE↗

Preparation and characterization of a hybrid alkaline binder based on a fly ash with no commercial value

Alkali-activated Portland fly ash cement (FA/OPC) and alkali activated blast furnace slag-fly ash cement (FA/GBFS) were prepared using 70% of a low quality fly ash (FA). The low quality is associated with a high content of unburned material (loss of ignition of 14.6%). The hybrid cements were activated by the alkaline solution in order to obtain an overall SiO 2 /Al 2 O 3 molar ratio of 5.0 and 6.0 and unique overall Na 2 O/SiO 2 molar ratio of 0.21. The microstructural characterization of the blended pastes generated in the systems showed the coexistence of amorphous gels C-A-S-H and N-A-S-H gels in the hybrid systems. The addition of OPC or GBFS increases the compressive strength (at 28 days of curing) up to 127% compared with the geopolymer systems based only on FA used in this study. The content of silicates soluble also plays an important role in the reaction products and higher SiO 2 /Al 2 O 3 lead to obtain higher mechanical performance and denser structure. The results obtained show that these hybrid cements are an effective way for valorization the waste used in this study for the production of high strength and low-carbon footprint cement-type material.

36 MATERIALS SCIENCE↗

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗

Structured water in polyelectrolyte dendrimers: Understanding small angle neutron scattering results through atomistic simulation

Based on atomistic molecular dynamics (MD) simulations, the small angle neutron scattering (SANS) intensity behavior of a single generation-4 (G4) polyelectrolyte polyamidoamine (PAMAM) starburst dendrimer is investigated at different levels of molecular protonation. The SANS form factor, P(Q), and Debye autocorrelation function, γ(r), are calculated from the equilibrium MD trajectory based on a mathematical approach proposed in this work which provides a link between the neutron scattering experiment and MD computation. The simulations enable scattering calculations of not only the hydrocarbons, but also the contribution to the scattering length density fluctuations caused by structured, confined water within the dendrimer. Based on our computational results, we question the validity of using radius of gyration RG for microstructure characterization of a polyelectrolyte dendrimer from the scattering perspective.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

First Annual Progress Report on Radiation Tolerance of Controlled Fusion Welds in High Temperature Oxidation Resistant FeCrAl Alloys

The present report summarizes and discusses the first year efforts towards developing a modern, nuclear grade FeCrAl alloy designed to have enhanced radiation tolerance and weldability under the Department of Energy (DOE) Nuclear Energy Enabling Technologies (NEET) program. Significant efforts have been made within the first year of this project including the fabrication of seven candidate FeCrAl alloys with well controlled chemistry and microstructure, the microstructural characterization of these alloys using standardized and advanced techniques, mechanical properties testing and evaluation of base alloys, the completion of welding trials and production of weldments for subsequent testing, the design of novel tensile specimen geometry to increase the number of samples that can be irradiated in a single capsule and also shorten the time of their assessment after irradiation, the development of testing procedures for controlled hydrogen ingress studies, and a detailed mechanical and microstructural assessment of weldments prior to irradiation or hydrogen charging. These efforts and research results have shown promise for the FeCrAl alloy class as a new nuclear grade alloy class.

36 MATERIALS SCIENCE↗

Multiphase Microstructure in a Metastability-Assisted Medium Carbon Alloy Steel

A medium carbon alloy steel is processed by austenizing at 900 °C for 30 min, then rapid quenching into a patented quenching liquid and holding at 170 °C for 5 min, finally isothermally holding at 250 °C for different times. The morphology and mechanical properties are performed by using optical microscopy and scanning electron microscopy. A multiphase microstructure characterized by a mixture of lenticular prior martensite (PM), fine needle bainitic ferrite and filmy retained austenite (RA) is obtained. It is found that the PM formed firstly upon quenching can accelerate the subsequent bainitic transformation and promote refinement of multiphase colonies. The results show that an optimum mechanical property of a 4000.9 MPa bending strength and a 2030 MPa tensile strength is achieved at 250 °C for 120 min, which is attributed to the multiphase microstructural characteristics and a high product of the volume fraction of RA and the carbon content of austenite.

36 MATERIALS SCIENCE↗

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗

Characteristics of Premature Creep Failure in Over-tempered Base Metal of Grade 91 Steel Weldment

Characteristics of premature creep failure in the over-tempered base metal (OT-BM) of a Grade 91 steel weldment are investigated with specially designed creep experiments and advanced microstructure characterization. In situ digital image correlation (DIC) strain measurements reveal that local creep strain as high as 100% accumulated in the OT-BM, compared with only 10% nominal strain over the gauge length. The creep strain rate in the OT-BM is identical to that in the intercritical heat-affected zone and fine-grained heat-affected zone at the secondary creep stage and early tertiary stage, but faster at the late tertiary stage. Microstructural analysis shows that highly recovered microstructure in the OT-BM leads to the lowest hardness, the largest grain size, the lowest fraction of coincidence site lattice boundaries, and the lowest localized strain energy. Dislocation creep and transgranular creep fracture are the dominant deformation and fracture mechanisms in the OT-BM under the current creep testing condition of a low temperature (550 °C) and a high stress (215 MPa).

42 ENGINEERING↗

Development of a lab-scale, high-resolution, tube-generated X-ray computed-tomography system for three-dimensional (3D) materials characterization

The design and construction of a modular high resolution X-ray computed tomography (XCT) system is highlighted in this paper. The design approach is detailed for meeting a specified set of instrument performance goals tailored towards experimental versatility and high resolution imaging. The XCT tool is unique in the detector and X-ray source design configuration, enabling control in the balance between detection efficiency and spatial resolution. The system package is also unique: The sample manipulation approach implemented enables a wide gamut of in situ experimentation to analyze structure evolution under applied stimulus, by optimizing scan conditions through a high degree of controllability. The component selection and design process is detailed: Incorporated components are specified, custom designs are shared, and the approach for their integration into a fully functional XCT scanner is provided. Custom designs discussed include the dual-target X-ray source cradle which maintains position and trajectory of the beam between the two X-ray target configurations with respect to a scintillator mounting and positioning assembly and the imaging sensor, as well as a novel large-format X-ray detector with enhanced adaptability. The instrument is discussed from an operational point of view, including the details of data acquisition and processing implemented for 3D imaging via micro-CT. The performance of the instrument is demonstrated on a silica-glass particle/hydroxyl-terminated-polybutadiene (HTPB) matrix binder PBX simulant. Post-scan data processing, specifically segmentation of the sample's relevant microstructure from the 3D reconstruction, is provided to demonstrate the utility of the instrument. - Highlights: • Custom built X-ray tomography system for microstructural characterization • Detector design for maximizing polychromatic X-ray detection efficiency • X-ray design offered for maximizing X-ray flux with respect to imaging resolution • Novel lab-scale XCT data acquisition and data processing methods • 3D characterization of glass-bead mock plastic-bonded-explosive stimulant.

36 MATERIALS SCIENCE↗

Precipitation-site competition in duplex stainless steels: Cu clusters vs spinodal decomposition interfaces as nucleation sites during thermal aging

Competing microstructural evolution mechanisms can exist simultaneously when duplex stainless steels are operating for several decades in a high temperature service environment. Such competition between different microstructural evolution pathways can be difficult to ascertain using simple model alloy systems necessitating detailed structural and compositional analysis of phase transformation mechanisms in complex alloys Thus, in this study duplex stainless steels with complex but well understood chemistries were used to investigate the relative importance of different heterogeneous nucleation sites – specifically spinodal decomposition and Cu clustering – on precipitation of Ni-Si-Mn particles during long term thermal aging. Precipitation of Ni-Si-Mn particles in duplex stainless steels and ferritic steels during thermal aging and irradiation is known to have profound effect on mechanical properties. Using duplex stainless steels with custom modified compositions along with atom probe tomography characterization and first-passage kinetic Monte Carlo (FPKMC) simulations it is revealed that while the interface between Cr and Fe formed during spinodal decomposition can be a pathway for diffusion of Ni, Si, Mn, and Cu, it is not a site that encourages precipitation of Ni-Si-Mn rich particles. Instead, the presence of a higher concentration of Cu in these steels leads to formation of small Cu clusters with high energy interfaces that act as nucleation sites for Ni-Si-Mn particles because of its strong interaction particularly with Ni increasing the chemical driving force for precipitation. These results will help inform predictive models for the use of duplex stainless steels and other precipitation-hardened alloys for extended operation at high temperatures.

Duplex stainless steel, Thermal aging, Precipitati↗

Varied enhancements in mechanical properties and sodium compatibility of Grade 92 by thermomechanical treatments

As a candidate material for advanced nuclear reactors, a ferritic-martensitic (FM) steel Grade 92 in the standard normalized and tempered (NT) condition was subjected to two types of thermomechanical treatments (TMTs) with one having a lower level of deformation (T5A) and the other having a higher level of deformation (T5B). The testing results of the three conditions indicated that the TMTs significantly improved yield strength, creep resistance, fracture toughness, and sodium corrosion resistance compared with the NT condition. T5A excelled at creep resistance while T5B at sodium corrosion resistance. Microstructural characterization of the three conditions supports the varied enhancements in the properties. This study suggests that an appropriate TMT can be developed and applied to FM steels to better meet specific application requirements.

36 MATERIALS SCIENCE↗

Study of Tritium Transport in Nuclear-Grade Graphite and Molten Fluoride Salt Systems

High-temperature salts are proposed as coolant in recent reactor technologies including Fluoride Salt-Cooled High Temperature Reactor (FHR) with fluoride salt as primary and secondary loop coolant, Molten Salt Reactors (MSRs) with fuel salt, and high-magnetic-field fusion machines with salt coolant blanket. The baseline coolant is {sup 7}Li{sub 2}BeF{sub 4} (flibe) due to its good thermal-hydraulic and neutronic properties. Tritium produced in flibe due to neutron irradiation makes the issue of tritium transport an area of great interest. In the temperature range of 427- 704 deg. C, tritium readily diffuses through metallic reactor structural materials, which makes tritium control and capture a key technical challenge. It is anticipated that tritium can be captured by graphite, as graphite material showed a high affinity for tritium in the Molten Salt Reactor Experiment (MSRE) due to the porous and irregular crystallite microstructure. Two types of nuclear grade graphite which used as core components for FHR: matrix graphite, which encapsulates the TRISO (Tri-structural-isotropic) fuel particles in FHR, and high purity, isotropic nuclear grade graphite IG-110 which can be used as moderator and reflector in reactor core for both fission and fusion reactor. The microstructure of matrix graphite and IG-110 is different from that of matrix graphite, due to the raw material and manufacturing processes. There are three phenomena important for predicting tritium transport in graphite-salt systems: tritium species diffusion in molten flibe; tritium species transport at the salt-graphite interface; and tritium species transport in graphite. In this summary microstructure characterization of IG-110 and matrix graphite, characterization of graphite-salt interface as well as techniques for trace tritium detection in graphite are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and Mechanical Properties of 21-6-9 Stainless Steel Electron Beam Welds

Welds can either be stronger or weaker than the base metals that they join depending on the microstructures that form in the fusion and heat-affected zones of the weld. In this paper, weld strengthening in the fusion zone of annealed 21-6-9 stainless steel is investigated using cross-weld tensile samples, hardness testing, and microstructural characterization. Due to the stronger nature of the weld, the cross-weld tensile tests failed in the base metal and were not able to generate true fusion zone mechanical properties. Nanoindentation with a spherical indenter was instead used to predict the tensile behavior for the weld metal. Extrapolation of the nanoindentation results to higher strains was performed using the Steinberg–Guinan and Johnson–Cook strength models, and the results can be used for weld strength modeling purposes. The results illustrate how microstructural refinement and residual ferrite formation in the weld fusion zone can be an effective strengthener for 21-6-9 stainless steel.

36 MATERIALS SCIENCE↗

Impact of forging direction on the recrystallization behaviour of nickel base superalloy AD730 billet material at subsolvus temperatures

Highlights: • Large unrecrystallized grains present a fine distribution of intragranular γ′ precipitates; • Intragranular precipitates play a key role on strain distribution and subsequent recrystallization behaviour for AD730; • Continuous dynamic recrystallization (CDRX) promotes the gradual consumption of large unrecrystallized grains. • Undissolved secondary precipitates play a key role on the microstructural evolution of AD730 • No significant effect associated to the forging direction on the recrystallization behaviour of AD730 was found. AD730™ is a newly developed Ni-based superalloy for turbine disk applications produced by cast and wrought processes. Conventional ingot-to-billet conversion is an expensive and very complex operation. Because of the difficulties to achieve a uniform strain for recrystallization, large unrecrystallized grains are retained along this process. Heterogeneities of grain size have a negative impact on subsequent forging processes as well as ultrasonic inspectability of the destination part. The main aim of this work is to analyse the impact of both forging direction (billet, cogging) and strain (ε = 0.3–2) on the microstructural evolution of AD730 at subsolvus temperatures from a semi-finished product (billet) under conditions representative of both cogging and hot forging operations. Special attention to the presence of large unrecrystallized grains was paid. Double truncated cones (DTCs) were hot forged at subsolvus temperatures followed by air cooling. SEM and EBSD analysis were conducted in the as-received (billet) and the as-forged conditions. AD730 alloy presents a complex microstructure characterized by the presence of large unrecrystallized grains, aligned in the billet direction, with remarkable differences in γ′ precipitates distribution as compared to recrystallized structures. The fine distribution of primary γ′ precipitates (pinning effect) plays a key role on grain size control but also on the recrystallization behaviour. Continuous dynamic recrystallization (CDRX) mechanism was found to be operating in the large unrecrystallized grains, promoting the formation intragranular DRX grains and the gradual recrystallization of these grains. Strain presents a strong effect on the microstructural evolution of AD730, increasing the recrystallization fraction and refining the structure. By contrast, no significant effect associated to the forging direction was found. Conditions representative of cogging operations (ε ≤ 0.6) at subsolvus temperatures were translated into large fractions of unrecrystallized structures (strain accumulation).

36 MATERIALS SCIENCE↗

Insights on carbon dioxide adsorption in a flexible 1-D coordination polymer from in situ X-ray scattering and density functional theory

A combination of in situ small-angle X-ray scattering (SAXS) microstructure characterization over scales ranging from 1 nm to 10 µm and powder X-ray diffraction (XRD) structure characterization under various gas/pressure/temperature conditions with density functional theory (DFT) calculations provides new insights for the CO2 sorption behavior of a one-dimensional porous coordination polymer: catena-bis­(di­benzoyl­methanato)(4,4′-bi­pyridyl)­nickel(II), denoted NiDBM-Bpy. The NiDBM-Bpy chains are held together by van der Waals forces, but the structure of guest-free NiDBM-Bpy is unsolved due to a lack of suitable crystals and high-quality powder XRD patterns. Nevertheless, SAXS and powder XRD can follow microstructural and structural changes as a function of gas pressure, composition and temperature. Both mixed-gas flow and static supercritical CO2 regimes are explored experimentally. DFT calculations are used to model the structural variation associated with XRD changes and hysteresis in the sorption isotherms. XRD and DFT calculations suggest that an orthorhombic Fddd structure with two CO2 per Ni emerges following a transition from the structure with lower molar volume and symmetry that exists without CO2 present.

Allen, Andrew J.↗