SEARCH · Search NASA

Results for “pump”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS1982

The mechanical design of a vapor compressor for a heat pump to be used in space

A heat pump developed for use in Spacelab as a stand-alone refrigeration unit as well as within a fluid loop system is discussed. It will provide an active thermal control for payloads. Specifications for the heat pump were established: (1) heat removal rates at the source; (2) heat source temperatures from room temperature; (3) heat-sink fluid temperatures at condenser inlet; and (4) minimum power consumption. A reversed Carnot cycle heat pump using Freon 12 as working fluid incorporating a one-cylinder reciprocating compressor was selected. The maximum crankshaft speed was fixed relatively high at 100 rpm. The specified cooling rates then made it necessary to select a cylinder volume of 10 cu cm, which was obtained with a bore of 40 mm and a stroke of 8 mm.

Berner, F.↗

NASA NTRS1982

Evaluation of left ventricular assist device pump bladders cast from ion-sputtered polytetrafluorethylene mandrels

A highly thromboresistant blood contacting interface for use in implanatable blood pump is investigated. Biomaterials mechanics, dynamics, durability, surface morphology, and chemistry are among the critical consideration pertinent to the choice of an appropriate blood pump bladder material. The use of transfer cast biopolymers from ion beam textured surfaces is investigated to detect subtle variations in blood pump surface morphology using Biomer as the biomaterial of choice. The efficacy of ion beam sputtering as an acceptable method of fabricating textured blood interfaces is evaluated. Aortic grafts and left ventricular assist devices were implanted in claves; the blood interfaces were fabricated by transfer casting methods from ion beam textured polytetrafluorethylene mandrels. The mandrels were textured by superimposing a 15 micron screen mesh; ion sputtering conditions were 300 volts beam energy, 40 to 50 mA beam, and a mandrel to source distance of 25 microns.

Source record↗

NASA NTRS1984

Transportable Pumps Could Save Oil Cargoes

Transportable pumps designed for firefighting used to salvage crude oil from tankships leaking, burning, or grounded. Pump incorporated into self-contained transportable module along with engine and controls. Module carried by helicopter, boat, or van to site of fire provides large quantities of water at high pressure in firefighting mode or pump oil into barge in salvage mode.

Burns, R.↗

NASA NTRS1982

A blackbody radiation-pumped CO2 laser experiment

Thermal radiation from a high temperature oven was used as an optical pump to achieve lasing from CO2 mixtures. Laser output as a function of blackbody temperature and gas conditions is described. This achievement represents the first blackbody cavity pumped laser and has potential for solar pumping.

Christiansen, W. H.↗

NASA NTRS1983

Research on solar pumped liquid lasers

A solar pumped liquid laser that can be scaled up to high power (10Mw CW) for space applications was developed. Liquid lasers have the inherent advantage over gases in that they provide much higher lasant densities and thus high power densities. Liquids also have inherent advantages over solids in that they have much higher damage thresholds and are much cheaper to produce for large scale applications. Among the liquid laser media that are potential candidates for solar pumping, the POC13:Nd(3+):ZrC14 liquid was chosen for its high intrinsic efficiency as well as its relatively good stability against decomposition due to protic contamination. The development and testing of the laser liquid and the development of a large solar concentrator to pump the laser was emphasized. The procedure to manufacture the laser liquid must include diagnostic tests of the solvent purity (from protic contamination) at various stages in the production process.

Schneider, R. T.↗

NASA NTRS1982

Investigation of the effects of initial fluid film profile on pumping ring operation

The effect of the initial fluid film profile on the pumping capacity of a pumping ring shaft seal has been investigated numerically. Linear, concave, convex and compound film shapes were considered. It was found that initial film shape has a pronounced effect on both the amount of fluid pumped and on the character of the flow pattern and pressure distribution within the film.

Smith, P. J.↗

NASA NTRS1982

Gain-enhanced free-electron laser with an electromagnetic pump field

The feasibility of enhancing the gain for the free electron laser (FEL) with an electromagnetic (EM) pump field has been considered. The enhancement is provided by reacceleration of the electrons in the interaction region by means of a static, axial electric field. A FEL utilizing a low energy electron beam and a wiggler magnet with a periodicity on the order of 1 cm would produce far infared (FIR) radiation with wavelengths on the order of a few hundred microns. The use of the FIR radiation as the pump field in a two-stage FEL is envisioned to obtain visible radiation with a low energy electron beam. A summary is provided regarding the theory and equations of motion for the EM-pumped FEL. The derived relations are applied to the second stage of such a two-stage FEL. The obtained equations have been incorporated into a computer code which has been used to calculate laser gain and energy conversion efficiency.

Hiddleston, H. R.↗

NASA NTRS1983

Blackbody-pumped CO2 laser experiment

Christiansen, W. H.↗

NASA NTRS1983

Tests of SSME low pressure pump in liquids at zero throughflow

Shutdown requirements in space of the Space Shuttle Main Engines require that the low pressure pump operate under conditions of zero flow and zero NPSH and still be able to generate head and absorb torque. Ground tests were conducted in both water and liquid oxygen to verify these capabilities. The test facilities are described, and the test results are presented showing the pump performance at zero flow over a wide range of NPSH conditions including zero values. The influence of operating speed, fluid medium, and internal struts upstream of the inducer are presented. A flow model schematic is presented sketching a flow field in the pump that is consistent with the observed data.

Jackson, E. D.↗

NASA NTRS1986

Lightweight, Switchable Peristaltic Pump

Peristaltic pump moves liquids through 50 or more channels simultaneously. Special feature of pump pressure plates remotely set between idle and operating positions. In new design, unnecessary to preposition pressure plates and, unnecessary to enter pump housing to move plates into operating mode.

Below, R. R.↗

NASA NTRS1986

Peristaltic Pump With a Stable Output

Proposed design for peristaltic pump decreases flow-rate change that results from loss of elasticity. Instead of tubing, new pump uses special flexible liner as pumping channel. Liner molded as single piece of flexible plastic with helical internal channels. Three rollers move around inner wall of liner, compressing channels and forcing liquid before constrictions. As rollers move on, channels open elastically, drawing in liquid from inlet port and making it available when rollers return.

Chandler, J. A.↗

NASA NTRS1985

Operational performance of the photovoltaic-powered grain mill and water pump at Tangaye, Burkina Faso (formerly Upper Volta)

A photovoltaic (PV) system powering a grain mill and water pump was installed in the remote African village of Tangaye, Burkina Faso (formerly Upper Volta) under the sponsorship of the U.S. Agency for International Development (AID) and by the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) in early 1979. The presence reports covers the second two years of operation from April 1981 through June 1983. During this time, the grain mill and water pump were operational 96 and 88 percent of the time respectively, and the PV system generated sufficient electricity to enable the grinding of about 111 metric tons of finely ground flow and the pumping of over 5000 cm sq of water from the 10 m deep well. The report includes a description of the current configuration of the system, a review of system performance, a discussion of the socioeconomic impact of the system on the villagers and a summary of results and conclusions covering the entire four-year period.

Martz, J. E.↗

NASA NTRS1985

Transient Analysis of a Magnetic Heat Pump

An experimental heat pump that uses a rare earth element as the refrigerant is modeled using NASTRAN. The refrigerant is a ferromagnetic metal whose temperature rises when a magnetic field is applied and falls when the magnetic field is removed. The heat pump is used as a refrigerator to remove heat from a reservoir and discharge it through a heat exchanger. In the NASTRAN model the components modeled are represented by one-dimensional ROD elements. Heat flow in the solids and fluid are analyzed. The problem is mildly nonlinear since the heat capacity of the refrigerant is temperature-dependent. One simulation run consists of a series of transient analyses, each representing one stroke of the heat pump. An auxiliary program was written that uses the results of one NASTRAN analysis to generate data for the next NASTRAN analysis.

Schroeder, E. A.↗

NASA NTRS1985

Efficient flashlamp-pumped IBr laser

The operating characteristics and scaling parameters of a flashlamp-pumped, 4-m-long IBr laser were investigated to further evaluate its potential as a solar-pumped laser. A peak power of 3 kW/sq cm at 2.7 microns was achieved at 4-Torr IBr pressure. A gain of 0.07 per m was measured at a maximum capacitor discharge energy of 4 kJ. The threshold input power necessary for lasing was found to decrease by a factor of 4 and the laser pulse width increased fourfold as the active gain length was increased from 1 to 4 m. A maximum pulse width of 120 microseconds was achieved with 10-Torr argon diluent added to 4-Torr IBr. Quenching of the excited state by the parent molecule was shown to be unimportant for pressures less than 4-Torr IBr. An intrinsic efficiency in the range of 12 percent has been measured for flashlamp-pumped IBr.

Zapata, L. E.↗

NASA NTRS1986

Pump for Saturated Liquids

Boiling liquids pumped by device based on proven components. Expanding saturated liquid in nozzle and diverting its phases along separate paths in liquid/vapor separator raises pressure of liquid. Liquid cooled in process. Pump makes it unnecessary to pressurize cryogenic liquids in order to pump them. Problems of introducing noncondensable pressurizing gas avoided.

Elliott, D. G.↗

NASA NTRS1985

Research on solar pumped liquid lasers

A solar pumped liquid laser that can be scaled up to high power (10 mW CW) for space applications was developed. Liquid lasers have the advantage over gases in that they provide much higher lasant densities and thus high-power densities. Liquids also have advantages over solids in that they have much higher damage thresholds and are much cheaper to produce for large scale applications. Among the liquid laser media that are potential candidates for solar pumping, the POC13: Nd sup 3+:ZrC14 liquid was chosen for its high intrinsic efficiency and its relatively good stability against decomposition due to protic contamination. The development of a manufacturing procedure and performance testing of the laser, liquid and the development of an inexpensive large solar concentrator to pump the laser are examined.

Cox, J. D.↗

NASA NTRS1985

lasants for transfer blackbody-pumped lasers

The concept of transfer blackbody-pumped lasers is outlined, recent research results concerning these lasers are presented and the search for new lasant materials for transfer blackbody-pumped lasers is expanded. There are two basic concepts for the blackbody-pumped transfer laser which are schematically drawn. The first concept is called the translational heating concept, an example being N2:CO2. Here the blackbody cavity is heated to approximately 2000 K by collected sunlight in space. An absorbing molecule would come in contact with the blackbody walls thus coming into equilibrium with the blackbody temperature. An alternative concept shown is called the vibrational heating transfer laser. Here the absorbing molecule is not translationally heated. Energy is coupled to the molecule only by optical absorption creating a high density of vibrational states. Thus the gas temperature is near room temperature whereas the vibrational temperature comes into equilibrium with the blackbody temperature.

Deyoung, R. J.↗

NASA NTRS1985

Pump instability phenomena generated by fluid forces

Rotor dynamic behavior of high energy centrifugal pumps is significantly affected by two types of fluid forces; one due to the hydraulic interaction of the impeller with the surrounding volute or diffuser and the other due to the effect of the wear rings. The available data on these forces is first reviewed. A simple one degree-of-freedom system containing these forces is analytically solved to exhibit the rotor dynamic effects. To illustrate the relative magnitude of these phenomena, an example of a multistage boiler feed pump is worked out. It is shown that the wear ring effects tend to suppress critical speed and postpone instability onset. But the volute-impeller forces tend to lower the critical speed and the instability onset speed. However, for typical boiler feed pumps under normal running clearances, the wear ring effects are much more significant than the destabilizing hydraulic interaction effects.

Gopalakrishnan, S.↗