Search NASA⌕ Search

SEARCH · Search NASA

Results for “responsive materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗

Identify the influence of microstructure on mesoscale creep and fatigue damage

This report describes the development of a microstructural model that can quantify the uncertainty in the observed rupture life of Grade 91 steel. The model is microstructural, meaning it relates microstructural characteristics of the material to the resulting material response. As such, one of the uses of this model is to identify the key microstructural parameters controlling the development of damage in Grade 91 operating at elevated temperatures. The report describes two veins of work: improvements to the crystal plasticity model required to run the uncertainty quantification analysis and the results of that UQ analysis. For creep, the model identifies the grain boundary diffusivity as the critical parameter controlling the rupture life of the material. The report demonstrates that a reasonable microstructural distribution of grain boundary diffusivity can account for the observed macroscale variation in rupture life at fixed temperature and load.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Lessons Learned from Aerothermal Flight Data on NASA Mars Entry Vehicles

The NASA Mars Science Laboratory (MSL) and Mars 2020 entry vehicles included temperature measurements inside and direct heat flux on the surface of the thermal protection system (TPS) material. The instrumentation was included to begin addressing predictive capabilities for aerodynamic heating and ablative TPS material response. The MSL aeroshell included temperature measurements at seven heatshield locations, from which total aerodynamic heating was reconstructed. The Mars 2020 instrumentation suite included eleven heatshield measurement locations and new backshell measurements at nine locations: six with temperature sensors, two with sensors to directly measure total heat flux, and one to measure radiative heat flux. Both instrumentation suites returned full sets of data, with all temperature sensors nearest to the surface surviving entry, indicating minimal material recession. Heatshield boundary layer transition (BLT) was observed for both vehicles prior to the time of peak heating, with transition starting near the shoulder and progressing towards the stagnation area. MSL’s higher speed on approach to Mars resulted in higher total heating compared to Mars 2020, with the maximum occurring near the heatshield’s leeside shoulder. The Mars 2020 backshell heating data indicate significant contributions from shock layer radiation. Heating from Navier-Stokes flowfield calculations are in family with reconstructed heating. The paper covers the instrumentation, BLT and reconstructed heating on both heatshields, backshell heating for Mars 2020, TPS performance, and predicted versus reconstructed heat fluxes. Opportunities for improved design approaches for future Mars missions are discussed, especially for the upcoming Mars Sample Return mission.

Mars Science Laboratory↗

Lessons Learned from Aerothermal Flight Data on NASA Mars Entry Vehicles

The NASA Mars Science Laboratory (MSL) and Mars 2020 entry vehicles included temperature measurements inside and direct heat flux on the surface of the thermal protection system (TPS) material. The instrumentation was included to begin addressing predictive capabilities for aerodynamic heating and ablative TPS material response. The MSL aeroshell included temperature measurements at seven heatshield locations, from which total aerodynamic heating was reconstructed. The Mars 2020 instrumentation suite included eleven heatshield measurement locations and new backshell measurements at nine locations: six with temperature sensors, two with sensors to directly measure total heat flux, and one to measure radiative heat flux. Both instrumentation suites returned full sets of data, with all temperature sensors nearest to the surface surviving entry, indicating minimal material recession. Heatshield boundary layer transition (BLT) was observed for both vehicles prior to the time of peak heating, with transition starting near the shoulder and progressing towards the stagnation area. MSL’s higher speed on approach to Mars resulted in higher total heating compared to Mars 2020, with the maximum occurring near the heatshield’s leeside shoulder. The Mars 2020 backshell heating data indicate significant contributions from shock layer radiation. Heating from Navier-Stokes flowfield calculations are in family with reconstructed heating. The paper covers the instrumentation, BLT and reconstructed heating on both heatshields, backshell heating for Mars 2020, TPS performance, and predicted versus reconstructed heat fluxes. Opportunities for improved design approaches for future Mars missions are discussed, especially for the upcoming Mars Sample Return mission.

Mars Science Laboratory↗

Leveraging the Polymer Glass Transition to Access Thermally Switchable Shear Jamming Suspensions

Suspensions of polymeric nano-and microparticles are fascinating stress-responsive material systems that, depending on their composition, can display a diverse range of flow properties under shear, such as drastic thinning, thickening, and even jamming (reversible solidification driven by shear). However, investigations to date have almost exclusively focused on nonresponsive particles, which do not allow in situ tuning of the flow properties. Polymeric materials possess rich phase transitions that can be directly tuned by their chemical structures, which has enabled researchers to engineer versatile adaptive materials that can respond to targeted external stimuli. Reported herein are suspensions of (readily prepared) micrometer-sized polymeric particles with accessible glass transition temperatures (T g ) designed to thermally control their non-Newtonian rheology. The underlying mechanical stiffness and interparticle friction between particles change dramatically near T g . Capitalizing on these properties, it is shown that, in contrast to conventional systems, a dramatic and nonmonotonic change in shear thickening occurs as the suspensions transition through the particles' T g . This straightforward strategy enables the in situ turning on (or off) of the system's ability to shear jam by varying the temperature relative to T g and lays the groundwork for other types of stimuli-responsive jamming systems through polymer chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid mapping of polarization switching through complete information acquisition

Polarization switching in ferroelectric and multiferroic materials underpins a broad range of current and emergent applications, ranging from random access memories to field-effect transistors, and tunnelling devices. Switching in these materials is exquisitely sensitive to local defects and microstructure on the nanometre scale, necessitating spatially resolved high-resolution studies of these phenomena. Classical piezoresponse force microscopy and spectroscopy, although providing necessary spatial resolution, are fundamentally limited in data acquisition rates and energy resolution. This limitation stems from their two-tiered measurement protocol that combines slow (~1 s) switching and fast (~10 kHz–1 MHz) detection waveforms. Here we develop an approach for rapid probing of ferroelectric switching using direct strain detection of material response to probe bias. This approach, facilitated by high-sensitivity electronics and adaptive filtering, enables spectroscopic imaging at a rate 3,504 times faster the current state of the art, achieving high-veracity imaging of polarization dynamics in complex microstructures.

36 MATERIALS SCIENCE↗

Establishing gold and platinum standards to 1 terapascal using shockless compression

New techniques are advancing the frontier of high-pressure physics beyond 1 terapascal, leading to new discoveries and offering stringent tests for condensed-matter theory and advanced numerical methods. However, the ability to absolutely determine the pressure state remains challenging, and well-calibrated pressure-density reference materials are required. We conducted shockless dynamic compression experiments at the National Ignition Facility and the Z machine to obtain quasi-absolute, high-precision, pressure-density equation-of-state data for gold and platinum. We derived two experimentally constrained pressure standards to terapascal conditions. Establishing accurate experimental determinations of extreme pressure will facilitate better connections between experiments and theory, paving the way toward improving our understanding of material response to these extreme conditions.

36 MATERIALS SCIENCE↗

INTERSTELLAR ENVIRONMENTS AND DUST PROPERTIES TOWARD CYGNUS OB2 NO. 12: A REASSESSMENT

The B-type hypergiant Cygnus OB2 no. 12 is a popular target for studies of interstellar phenomena at visible-infrared wavelengths because of its exceptional brightness for a star dimmed by some 10 mag of visual extinction. A lack of detectable ice absorption has led investigators to regard the line of sight as a standard for studies of the “diffuse” interstellar medium (ISM), an assumption challenged both by observations of molecular gas toward the star and by uncertainties concerning the degree to which such a luminous object may affect its local environment. This paper presents a reassessment of the nature of the material responsible for extinction toward Cyg OB2 no. 12. The excess relative to other cluster members appears to occur in translucent clumps within an extensive network of clouds in the region. Attenuation of the ambient radiation field is sufficient in the cores of the clumps to support the presence of gas-phase molecules, but not to sustain detectable ice formation. In general, the optical properties of dust in the clumps are closely similar to those observed in typical diffuse interstellar material, with the notable exception of an unusually low value for the wavelength of maximum polarization. The implied enhancement of polarization by small grains is attributed to increased alignment efficiency in an enhanced magnetic field. This caveat apart, the results of the current paper provide reassurance that Cyg OB2 no. 12 is, indeed, an appropriate choice for studies that target diffuse and translucent phases of the ISM.

79 ASTRONOMY AND ASTROPHYSICS↗

Icarus Application to Dragonfly Heatshield

Icarus, an in-house material response solver developed at NASA Ames, is applied to perform 2-D bondline-temperature analysis on the heatshield surface of the latest Dragonfly entry system design for a mission to Titan. Two axisymmetric domains are used: the near-shoulder region and the entire heatshield. The heatshield consists of a PICA TPS bonded to a layered system of Aluminum honeycomb wrapped by an M55J carbon-fiber facesheet. The backshell, which is also included for more accurate analysis, consists of similar materials layered. Icarus simulations using both domains indicate that the in-plane thermal conductivity property of the M55J facesheet is observed to play a dominant role in bondline temperature. Similarly, the maximum bondline temperature is found around the PICA-tile-interface region instead of the near-shoulder region or the stagnation point based on the current trajectory using the orthotropic properties of M55J. Therefore, these findings indicate the significance of 2-D or higher-dimensional material modeling analysis in fully understanding how bondline temperature behaves across the heatshield and obtaining a basis for TPS design locations. Verification at different radial locations ahead of the shoulder, where thermal conduction is close to 1-D, between Icarus (2-D), Icarus (1-D), and FIAT is performed and good agreement is observed. With the entire heatshield domain, the total mass loss of the aeroshell materials is approximately 3% of their initial mass potentially due to thermal decomposition of phenolic resins inside PICA under the current high-heating environment.

TPS material modeling↗

Evolution of dislocation substructures in metals via high-strain-rate nanoindentation

Deformation at high strain rates often results in high stresses on many engineering materials, potentially leading to catastrophic failure without proper design. High-strain-rate mechanical testing is thus needed to improve the design of future structural materials for a wide range of applications. Although several high-strain-rate mechanical testing techniques have been developed to provide a fundamental understanding of material responses and microstructural evolution under high-strain-rate deformation conditions, these tests are often very time consuming and costly. In this work, we utilize a high-strain-rate nanoindentation testing technique and system in combination with transmission electron microscopy to reveal the deformation mechanisms and dislocation substructures that evolve in pure metals from low (10 –2 s –1 ) to very high indentation strain rates (10 4 s –1 ), using face-centered cubic aluminum and body-centered cubic molybdenum as model materials. The results help to establish the conditions under which micro- and macro-scale tests can be compared with validity and also provide a promising pathway that could lead to accelerated high-strain-rate testing at substantially reduced costs.

36 MATERIALS SCIENCE↗

Hitomi observations of the LMC SNR N 132 D: Highly redshifted X-ray emission from iron ejecta

Here, we present Hitomi observations of N 132 D, a young, X-ray bright, O-rich core-collapse supernova remnant in the Large Magellanic Cloud (LMC). Despite a very short observation of only 3.7 ks, the Soft X-ray Spectrometer (SXS) easily detects the line complexes of highly ionized S K and Fe K with 16–17 counts in each. The Fe feature is measured for the first time at high spectral resolution. Based on the plausible assumption that the Fe K emission is dominated by He-like ions, we find that the material responsible for this Fe emission is highly redshifted at ~800 km s –1 compared to the local LMC interstellar medium (ISM), with a 90% credible interval of 50–1500 km s –1 if a weakly informative prior is placed on possible line broadening. This indicates that the Fe emission arises from the supernova ejecta, and that these ejecta are highly asymmetric, since no blueshifted component is found. The S K velocity is consistent with the local LMC ISM, and is likely from swept-up ISM material. These results are consistent with spatial mapping that shows the He-like Fe concentrated in the interior of the remnant and the S tracing the outer shell. The results also show that even with a very small number of counts, direct velocity measurements from Doppler-shifted lines detected in extended objects like supernova remnants are now possible. Thanks to the very low SXS background of ~1 event per spectral resolution element per 100 ks, such results are obtainable during short pointed or slew observations with similar instruments. This highlights the power of high-spectral-resolution imaging observations, and demonstrates the new window that has been opened with Hitomi and will be greatly widened with future missions such as the X-ray Astronomy Recovery Mission (XARM) and Athena.

79 ASTRONOMY AND ASTROPHYSICS↗

Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions

Many materials of interest to Sandia transition from fluid to solid or have regions of both phases coexisting simultaneously. Currently there are, unfortunately, no material models that can accurately predict this material response. This is relevant to applications that "birth stress" related to geoscience, nuclear safety, manufacturing, energy production and bioscience. Accurately capturing solidification and residual stress enables fully predictive simulations of the evolving front shape or final product. Accurately resolving flow of proppants or blood could reduce environmental impact or lead to better treatments for heart attacks, thrombosis, or aneurism. We will address a science question in this proposal: When does residual stress develop during the critical transition from liquid to solid and how does it affect material deformation? Our hypothesis is that these early phases of stress development are critical to predictive simulation of material performance, net shape, and aging. In this project, we use advanced constitutive models with yield stress to represent both fluid and solid behavior simultaneously. The report provides an abbreviated description of the results from our LDRD "Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions," since we have written four papers that document the work in detail and which we reference. We give highlights of the work and describe the gravitationally driven flow visualization experiment on a model yield stress fluid, Carbopol, at various concentrations and flow rates. We were able to collapse the data on a single master curve by showing it was self-similar. We also describe the Carbopol rheology and the constitutive equations of interest including the Bingham-Carreau-Yasuda model, the Saramito model, and the HB-Saramito model including parameter estimation for the shear and oscillatory rheology. We present several computational models including the 3D moving mesh simulations of both the Saramito models and Bingham-Carreau-Yasuda (BCY) model. We also show results from the BCY model using a 3D level set method and two different ways of handling reduced order Hele-Shaw modeling for generalized Newtonian fluids. We present some first ever two-dimensional results for the modified Jeffries Kamani-Donley-Rogers constitutive equation developed during this project. We include some recent results with a successful Saramito-level set coupling that allows us to tackle problems with complex geometries like mold filling in a thin gap with an obstacle, without the need for remeshing or remapping. We report on some experiments for curing systems where fluorescent particles are used to track material flow. These experiments were carried out in an oven on Sylgard 184 as a model polymerizing system. We conclude the report with a summary of accomplishments and some thoughts on follow-on work.

36 MATERIALS SCIENCE↗

TPSAS-NF1676L-13792-DND

Extreme structural requirements of future aerospace vehicles motivate the development of new, ultra-durable materials and game-changing methodologies for material certification and sustainment. Computational simulations spanning many orders of magnitude in length and time scales—from the nanoscale of underlying damage processes to the larger scales of continuum cracks—are being developed to support these requirements. Results of these simulations are used to deduce key aspects of material response to loads and environments, including: - The microstructural mechanics that govern metal fatigue crack initiation and growth - The variety and complexity of the dislocation-precipitate interac- tions that underpin plastic behavior and damage evolution - The energetic principles that govern the interaction of water with crack surfaces within a structural component - The mechanics of grain boundary separation Modeling the physics behind these metal fatigue behaviors is extremely complex, and requires intensive, high-fidelity simulations. The knowledge gained through these simulations, however, is forming the keystone for advanced material design and will enable development of more capable, reliable structures for aerospace vehicles.

Jacob Hochhalter↗

Characterization of ablator dynamics initiated by picket-pulse conditions

Direct-drive laser-fusion targets may include low-cost plastic ablator material. Here, this work describes a tabletop experimental system designed to enable the investigation of the interaction of such ablator material as a function of the laser wavelength and the associated excitation mechanism. This experimental system offers time-resolved imaging of the material response with subpicosecond temporal resolution and ≈1-μm spatial resolution. The system involves synchronized femtosecond and picosecond lasers to initiate and characterize the dynamics of polystyrene planar targets irradiated by conditions similar to a “picket” prepulse from a direct-drive pulse shape. Ultrafast imaging of the initial excitation process followed by the resulting critical plasma formation, shock-wave propagation, and blowoff plasma expansion is used to compare the impact of excitation wavelength, 355 nm or 266 nm, on the ensuing dynamics. This work aims to investigate fundamental laser material interactions to help advance physics models that can inform the development of laser driver and target designs.

42 ENGINEERING↗

Informing ARC divertor design and plasma facing material selection through integrated modeling

This INFUSE 2023 project between UCLA and Commonwealth Fusion Systems used computer modeling to test whether tungsten materials can survive in CFS's ARC fusion reactor divertor. The team simulated plasma conditions and material responses, finding that tungsten-rhenium alloys resist grain growth better than pure tungsten, and that hydrogen buildup depends more on particle flux than temperature. The work helps CFS design durable plasma-facing components for their fusion power plant.

36 MATERIALS SCIENCE↗

3D RoboMET Characterization

The goal of this project is to generate 3D microstructural data by destructive and non-destructive means and provide accompanying characterization and quantitative analysis of such data. This work is a continuing part of a larger effort to relate material performance variability to microstructural variability. That larger effort is called “Predicting Performance Margins” or PPM. In conjunction with that overarching initiative, the RoboMET.3D™ is a specific asset of Center 1800 and is an automated serialsectioning system for destructive analysis of microstructure, which is called upon to provide direct customer support to 1800 and non-1800 customers. To that end, data collection, 3d reconstruction and analysis of typical and atypical microstructures have been pursued for the purposes of qualitative and quantitative characterization with a goal toward linking microstructural defects and/or microstructural features with mechanical response. Material systems examined in FY15 include precipitation hardened 17-4 steel, laser-welds of 304L stainless steel, thermal spray coatings of 304L and geological samples of sandstone.

Madison, Jonathan D.↗

Development of an in situ ion irradiation scanning electron microscope

An in situ ion irradiation scanning electron microscope (I 3 SEM) has been developed, installed, and integrated into the Ion Beam Laboratory at Sandia National Laboratories. The I 3 SEM facility combines a field emission, variable pressure, scanning electron microscope, a 6 MV tandem accelerator, high flux low energy ion source, an 808 nm-wavelength laser, and multiple stages to control the thermal and mechanical state of the sample observed. The facility advances real-time understanding of materials evolution under combined environments at the mesoscale. As highlighted in multiple examples, this unique combination of tools is optimized for studying mesoscale material response in overlapping extreme environments, allowing for simultaneous ion irradiation, implantation, laser bombardment, conductive heating, cooling, and mechanical deformation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗