Trajectory Modeling of Particles Propelled by a Multi-Engine Rocket Plume on the Lunar Surface
Trajectory Modeling of Particles Propelled by a Multi-Engine Rocket Plume on the Lunar Surface
Lane, John E.↗
SEARCH · Search NASA
Results for “rocket engine”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Photographic Study of Liquid-Oxygen Boiling and Gas Injection in the Injector of a Chugging Rocket Engine
High-speed motion pictures were taken of conditions in the injector liquid-oxygen cavity of an RL-10 rocket engine during throttled engine operation. Photographs were taken during operation of the engine in the chugging region as the helium gas was injected to stabilize combustion, during operation at rated thrust, and during transition into chugging conditions as the gas injection was discontinued. Results of the investigation indicate that, during chugging rocket operation of the RL-10 engine, a high population of fairly large bubbles formed and collapsed within the liquid-oxygen cavity at the same frequency as the chamber pressure oscillations. When gaseous helium was injected into the liquid-oxygen cavity, a fog rapidly spread over the entire field of view, and the system immediately became stable. The injection of gaseous helium at rated conditions produced a very slight increase in engine performance but not enough to produce a net gain in a typical mission payload with the extra equipment needed. The inherent low-frequency system instability associated with the fuel system at low thrust levels was reduced by injecting either gaseous helium or hydrogen. Complete stabilization was achieved in some cases, and a reduction in the severity of the oscillations in others. This was apparently due to the ·anchoring of the phase change front to the location of the gas injection.
Conrad, E. William↗
Combustion Processes in Hybrid Rocket Engines
In recent years, there has been a resurgence of interest in the development of hybrid rocket engines for advanced launch vehicle applications. Hybrid propulsion systems use a solid fuel such as hydroxyl-terminated polybutadiene (HTPB) along with a gaseous/liquid oxidizer. The performance of hybrid combustors depends on the convective and radiative heat fluxes to the fuel surface, the rate of pyrolysis in the solid phase, and the turbulent combustion processes in the gaseous phases. These processes in combination specify the regression rates of the fuel surface and thereby the utilization efficiency of the fuel. In this paper, we employ computational fluid dynamics (CFD) techniques in order to gain a quantitative understanding of the physical trends in hybrid rocket combustors. The computational modeling is tailored to ongoing experiments at Penn State that employ a two dimensional slab burner configuration. The coordinated computational/experimental effort enables model validation while providing an understanding of the experimental observations. Computations to date have included the full length geometry with and with the aft nozzle section as well as shorter length domains for extensive parametric characterization. HTPB is sed as the fuel with 1,3 butadiene being taken as the gaseous product of the pyrolysis. Pure gaseous oxygen is taken as the oxidizer. The fuel regression rate is specified using an Arrhenius rate reaction, which the fuel surface temperature is given by an energy balance involving gas-phase convection and radiation as well as thermal conduction in the solid-phase. For the gas-phase combustion, a two step global reaction is used. The standard kappa - epsilon model is used for turbulence closure. Radiation is presently treated using a simple diffusion approximation which is valid for large optical path lengths, representative of radiation from soot particles. Computational results are obtained to determine the trends in the fuel burning or regression rates as a function of the head-end oxidizer mass flux, G=rho(e)U(e), and the chamber pressure. Furthermore, computation of the full slab burner configuration has also been obtained for various stages of the burn. Comparisons with available experimental data from small scale tests conducted by General Dynamics-Thiokol-Rocketdyne suggest reasonable agreement in the predicted regression rates. Future work will include: (1) a model for soot generation in the flame for more quantitative radiative transfer modelling, (2) a parametric study of combustion efficiency, and (3) transient calculations to help determine the possible mechanisms responsible for combustion instability in hybrid rocket motors.
Venkateswaran,S.↗
Analysis of a Radioisotope Thermal Rocket Engine
The Triton Hopper is a concept for a global hopper vehicle which uses a radioisotope rocket engine and In-situ propellant acquisition to explore the surface of Neptune's moon, Triton. The current Triton Hopper concept stores heated Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through the use of a thermal block during engine operation, as opposed to storing gas at a high temperature. Lithium, Lithium Fluoride and Beryllium were considered as possible materials for the thermal block. A heat energy analysis indicated that a lithium thermal mass would provide the highest heat energy for a temperature change from 900 Celsius to -100 Celsius. A heat transfer analysis was performed for Nitrogen at -100 Celsius flowing through 1000 passages inside a 1kg lithium thermal block at a temperature of 900 Celsius. The system was analyzed as turbulent flow through a tube with constant surface temperature. The analysis indicated that the propellant reached a maximum temperature of 877 Celsius before entering the nozzle. At this exit temperature, the average specific impulse [I(sub sp)] of the engine was determined to be 157s. Previous studies for the stored heated gas concept suggest that the engine would have an average I(sub sp) of approximately 52s. Thus, the use of a thermal block concept results in a 200 percent engine performance increase. In addition, a tank sizing study was performed to determine if the concept is feasible in terms of mass requirements. The mass for a spherical carbon fiber COPV storing 35kg of nitrogen at an initial temperature of -100 Celsius and a pressure of 1000psia, was determined to be 7.2kg. The specific impulse analysis indicated that the maximum engine performance is obtained for a mass ratio of 5kg of Nitrogen per every 1kg of lithium thermal mass. Thus for 35kg of Nitrogen the total thermal mass would be 7kg. This brings the total mass of the system to 49.2.kg which is less than the 56kg landing payload capacity of the Triton Hopper. Finally, an insulation analysis using 10mm of MLI insulation indicated that a total of 22 watts of heat are lost to the environment. With the heat loss known, the power required to heat the thermal mass to 900 Celsius in 24 days was determined to be 2.15 watts. The study's results allowed us to conclude that the thermal mass concept is the better option due to the performance increase provided, the low power requirement and its compliance with the landing mass requirement of the Triton Hopper.
Radioisotope↗
Designing Liquid Rocket Engine Injectors for Performance, Stability, and Cost
NASA is developing the Space Launch System (SLS) for crewed exploration missions beyond low Earth orbit. Marshall Space Flight Center (MSFC) is designing rocket engines for the SLS Advanced Booster (AB) concepts being developed to replace the Shuttle-derived solid rocket boosters. One AB concept uses large, Rocket-Propellant (RP)-fueled engines that pose significant design challenges. The injectors for these engines require high performance and stable operation while still meeting aggressive cost reduction goals for access to space. Historically, combustion stability problems have been a critical issue for such injector designs. Traditional, empirical injector design tools and methodologies, however, lack the ability to reliably predict complex injector dynamics that often lead to combustion stability. Reliance on these tools alone would likely result in an unaffordable test-fail-fix cycle for injector development. Recently at MSFC, a massively parallel computational fluid dynamics (CFD) program was successfully applied in the SLS AB injector design process. High-fidelity reacting flow simulations were conducted for both single-element and seven-element representations of the full-scale injector. Data from the CFD simulations was then used to significantly augment and improve the empirical design tools, resulting in a high-performance, stable injector design.
Westra, Douglas G.↗
Rocket engine nozzle photographic system
Protective enclosure for a camera, located on the exhaust stream of a rocket engine, permits continuous recording of erosion processes of materials used in nozzle throat structures. The system uses a standard camera in a water-cooled, pressurized enclosure having a unique, inert gas-swept viewing duct.
Bailey, R. L.↗
On the design of acoustic liners for rocket engines - Maximum damping as a design objective
Parameters of acoustic liner for maximum liner damping for rocket engines
Phillips, B.↗
Optimizing a liquid propellant rocket engine with an automated combustor design code (AUTOCOM)
A procedure for automatically designing a liquid propellant rocket engine combustion chamber in an optimal fashion is outlined. The procedure is contained in a digital computer code, AUTOCOM. The code is applied to an existing engine, and design modifications are generated which provide a substantial potential payload improvement over the existing design. Computer time requirements for this payload improvement were small, approximately four minutes in the CDC 6600 computer.
Hague, D. S.↗
Operation of small rocket engines in the JPL high-vacuum molecular space simulator (Molsink)
The feasibility of operating small rocket engines in the Molsink facility was demonstrated. A 0.44-N (0.1-lbf) hydrazine engine and a 0.18-N (0.04-lbf) thruster using cold gas from a hydrazine plenum system were operated for both flight duty cycles and off-nominal conditions. The exhaust gases from these thrusters contain NH3, N2, and H2. The chamber was also calibrated for larger bipropellant engines using nitrogen tetroxide/monomethyl hydrazine (NTO/MMH). The exhaust products of these engines contain CO2, CO, H2, H2O, and H2. A mixture of cold gases simulating the engine exhaust was injected through a nozzle under conditions simulating thrust levels up to 26.7-N (6 lbf). Pulsing and continuous operations were investigated. The chamber background pressure traces were compared with the traces obtained for the same thrusters operated with pure nitrogen at approximately equivalent thrust. Satisfactory recuperation times were encountered in all the pulsing modes. Test times greater than 20s were obtained in steady state operation before the vacuum chamber back pressure climbed to prohibitive values.
Chirivella, J. E.↗
Simulation of liquid propellant rocket engine combustion instabilities
A simulation technique for studying the high frequency combustion instabilities of liquid propellant rocket engines has been developed and used to investigate various aspects of instability phenomena. Of importance was investigation of the significance of the method of coupling the combustion and the gas dynamics of the system. Two coupling processes were studied: linear response of the combustion process to pressure fluctuations, and the nature of the resulting instabilities; and nonlinear response of the combustion process to velocity fluctuations, and the nature of the resulting instabilities. For the combustion model studied, nonlinear (velocity) coupling was found to more closely characterize liquid propellant instabilities.
Ventrice, M. B.↗
Low loss injector for liquid propellant rocket engines
A low pressure loss injector element is disclosed for the main combustion chamber of a rocket engine which includes a lox post terminating in a cylindrical barrel. Received within the barrel is a lox plug which is threaded in the lox post and includes an interchangeable lox metering sieve which meters the lox into an annular lox passage. A second annular gas passage is coaxial with the annular lox passage. A cylindrical sleeve surrounds the annular gas passage and includes an interchangeable gas metering seive having metering orifices through which a hot gas passes into the annular passage. The jets which emerge from the annular lox passage and annular gas passage intersect in a recessed area away from the combustion area. Thus, mixing and combustion stability are enhanced.
Vonpragenau, G. L.↗
Transpiration And Regenerative Cooling Of Rocket Engine
Transpiration cooling extends limits of performance. Addition of transpiration cooling to regeneratively-cooled rocket-engine combustion chamber proposed. Modification improves performance of engine by allowing use of higher chamber pressure. Throat section of combustion-chamber wall cooled by transpiration, while chamber and nozzle sections cooled by fluid flowing in closed channels. Concept applicable to advanced, high-performance terrestrial engines or some kinds of industrial combustion chambers. With proper design, cooling scheme makes possible to achieve higher chamber pressure and higher overall performance in smaller engine.
Obrien, Charles J.↗
Software for Preprocessing Data From Rocket-Engine Tests
Three computer programs have been written to preprocess digitized outputs of sensors during rocket-engine tests at Stennis Space Center (SSC). The programs apply exclusively to the SSC "E" test-stand complex and utilize the SSC file format. The programs are the following: 1) Engineering Units Generator (EUGEN) converts sensor-output-measurement data to engineering units. The inputs to EUGEN are raw binary test-data files, which include the voltage data, a list identifying the data channels, and time codes. EUGEN effects conversion by use of a file that contains calibration coefficients for each channel; 2) QUICKLOOK enables immediate viewing of a few selected channels of data, in contradistinction to viewing only after post test processing (which can take 30 minutes to several hours depending on the number of channels and other test parameters) of data from all channels. QUICKLOOK converts the selected data into a form in which they can be plotted in engineering units by use of Winplot (a free graphing program written by Rick Paris); and 3) EUPLOT provides a quick means for looking at data files generated by EUGEN without the necessity of relying on the PVWAVE based plotting software.
Cheng, Chiu-Fu↗
Software for Preprocessing Data from Rocket-Engine Tests
Three computer programs have been written to preprocess digitized outputs of sensors during rocket-engine tests at Stennis Space Center (SSC). The programs apply exclusively to the SSC E test-stand complex and utilize the SSC file format. The programs are the following: Engineering Units Generator (EUGEN) converts sensor-output-measurement data to engineering units. The inputs to EUGEN are raw binary test-data files, which include the voltage data, a list identifying the data channels, and time codes. EUGEN effects conversion by use of a file that contains calibration coefficients for each channel. QUICKLOOK enables immediate viewing of a few selected channels of data, in contradistinction to viewing only after post-test processing (which can take 30 minutes to several hours depending on the number of channels and other test parameters) of data from all channels. QUICKLOOK converts the selected data into a form in which they can be plotted in engineering units by use of Winplot (a free graphing program written by Rick Paris). EUPLOT provides a quick means for looking at data files generated by EUGEN without the necessity of relying on the PV-WAVE based plotting software.
Cheng, Chiu-Fu↗
Software for Preprocessing Data From Rocket-Engine Tests
Three computer programs have been written to preprocess digitized outputs of sensors during rocket-engine tests at Stennis Space Center (SSC). The programs apply exclusively to the SSC E test-stand complex and utilize the SSC file format. The programs are the following: (1) Engineering Units Generator (EUGEN) converts sensor-output-measurement data to engineering units. The inputs to EUGEN are raw binary test-data files, which include the voltage data, a list identifying the data channels, and time codes. EUGEN effects conversion by use of a file that contains calibration coefficients for each channel. (2) QUICKLOOK enables immediate viewing of a few selected channels of data, in contradistinction to viewing only after post-test processing (which can take 30 minutes to several hours depending on the number of channels and other test parameters) of data from all channels. QUICKLOOK converts the selected data into a form in which they can be plotted in engineering units by use of Winplot. (3) EUPLOT provides a quick means for looking at data files generated by EUGEN without the necessity of relying on the PVWAVE based plotting software.
Cheng, Chiu-Fu↗
Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle
A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.
detonation↗
Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle
A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.
detonation↗
Rocket engine evaluation of erosion and char as functions of fabric orientation for silica-reinforced nozzle materials
Rocket engine evaluation of erosion and char as functions of fabric orientation for silica reinforced nozzle materials
Peterson, D. A.↗