Search NASA⌕ Search

SEARCH · Search NASA

Results for “solution processable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Recent Improvements in the FDNS CFD Code and its Associated Process

This viewgraph presentation gives an overview on recent improvements in the Finite Difference Navier Stokes (FDNS) computational fluid dynamics (CFD) code and its associated process. The development of a utility, PreViewer, has essentially eliminated the creeping of simple human error into the FDNS Solution process. Extension of PreViewer to encapsulate the Domain Decompression process has made practical the routine use of parallel processing. The combination of CVS source control and ATS consistency validation significantly increases the efficiency of the CFD process.

West, Jeff S.↗

In situ Al 2 O 3 incorporation enhances the efficiency of CuIn(S,Se) 2 solar cells prepared from molecular-ink solutions

Here, we report an efficiency enhancement of solution-processed CuIn(S,Se) 2 (CISSe) thin film solar cells via in situ incorporation of Al 2 O 3 . These films were produced using inks containing CuCl, InCl 3 , AlNO 3 (Al/Al + In: 0.1) and thiourea dissolved in methanol. After spin coating of these solutions in air, samples were subjected to a selenization process. Auger electron spectroscopy depth-profiling analysis showed that Al is evenly distributed throughout the bulk of the film. Transmission electron microscopy revealed that AlNO 3 precursor reacted with oxygen to form nanosized amorphous Al 2 O 3 grains located within the bulk and grain boundaries of CISSe, as well as at both the top and bottom interfaces. Power conversion efficiency (PCE) as high as 11.6% (JS C : 35.8 mA cm –2 , V OC : 518 mV, FF: 62.2%, no anti-reflection coating) was achieved with Al–CISSe solar cell devices integrated with CdS (chemical bath deposition, thickness: 80 nm) and ZnO/ITO bilayers (sputtered, thickness: 300 nm). The average PCE (10.1%, $\langle$J SC $\rangle$: 34.5 mA cm –2 , $\langle$V OC $\rangle$: 491 mV, $\langle$FF$\rangle$: 59.8%) was nearly 4% (absolute) higher than that measured on CISSe baseline cells fabricated from solutions without Al ($\langle$PCE$\rangle$ = 6.4%, $\langle$J SC $\rangle$: 32.8 mA cm –2 , $\langle$V OC $\rangle$: 410 mV, $\langle$FF$\rangle$: 47.3%). This in situ Al 2 O 3 incorporation is speculated to play a role in the enhancement of the VOC and FF of the devices through passivation of defects in CISSe reducing interface and bulk recombination, as evidenced by a reduced defect density and an increased activation energy of the dominant recombination mechanism from capacitance and temperature-dependent VOC measurements, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Inorganic Precursors for Manufacturing of Photovoltaic Devices: Cooperative Research and Development Final Report, CRADA Number CRD-08-308

Both NREL and Rohm and Haas Electronic Materials are interested in the development of solution phase metal and semiconductive precursors for the manufacturing of photovoltaic devices. In particular, we intend to develop material sets for atmospheric deposition processes. The cooperation between these two parties will enable high value materials and processing solutions for the manufacturing of low cost, roll-to-roll photovoltaics.

14 SOLAR ENERGY↗

Separating Bulk and Surface Contributions to Electronic Excited-State Processes in Hybrid Mixed Perovskite Thin Films via Multimodal All-Optical Imaging

A comprehensive understanding of electronic excited-state phenomena underlying the impressive performance of solution-processed hybrid halide perovskite solar cells requires access to both spatially resolved electronic processes and corresponding sample morphological characteristics. In this paper, we demonstrate an all-optical multimodal imaging approach that enables us to obtain both electronic excited-state and morphological information on a single optical microscope platform with simultaneous high temporal and spatial resolution. Specifically, images were acquired for the same region of interest in thin films of chloride containing mixed lead halide perovskites (CH 3 NH 3 PbI 3–x Cl x ) using femtosecond transient absorption, time-integrated photoluminescence, confocal reflectance, and transmission microscopies. Comprehensive image analysis revealed the presence of surface- and bulk-dominated contributions to the various images, which describe either spatially dependent electronic excited-state properties or morphological variations across the probed region of the thin films. Finally, these results show that PL probes effectively the species near or at the film surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ANSTO Synroc Wasteforms for the Immobilization of a Range of Mo-99 Production Wastes - 19326

Tc-99m, the most commonly used radioisotope in nuclear medicine, is produced from the decay of Mo-99 which is predominantly produced in reactors by irradiation of enriched uranium targets. This results in three waste streams, one of which is a uranium filter cake containing fission products. This filter cake could itself be treated as a waste stream, or processed to retrieve the enriched uranium for further use, thus producing additional waste streams during reprocessing. All wastes are considered intermediate-level wastes and require an appropriate wasteform design for termination. ANSTO is collaborating with NECSA (Nuclear Energy Corporation of South Africa) to develop wasteform and processing solutions for the treatment of intermediate level wastes (ILW) from the production of Mo-99. The work is supported by the U.S. Department of Energy's (DOE) National Nuclear Security Administration (NNSA) with technical support from Argonne National Laboratory (ANL). Here we highlight some of the outcomes of this collaboration which has seen the investigation and performance testing of a range of waste treatment technologies. Among the treatment options for the various waste streams, including the enriched uranium filter cake itself, were glass, glass-ceramic, ceramic and geopolymer wasteforms. All wasteforms were characterized (e.g., by X-ray diffraction (XRD) and scanning electron microscopy (SEM)) and their performance characteristics, for example compressive strength and aqueous durability, determined by standard methods and compared. Consideration has been given to the most suitable, practical and cost effective solutions for the immobilization of these Mo-99 wastes. This paper will discuss the down-selection of wasteforms and process technologies for Mo-99 wastes and compare these with regards to wasteform performance and process technology readiness. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemical Robotics Enabled Exploration of Stability in Multicomponent Lead Halide Perovskites via Machine Learning

Metal halide perovskites have attracted immense interest as a promising material for a variety of optoelectronic and sensing applications. However, issues regarding long-term stability have emerged as the key bottleneck for commercialization. Here, we develop an automated experimental workflow based on combinatorial synthesis and rapid throughput characterization to explore long-term stability of these materials in ambient conditions. We apply it to four model perovskite systems: MA x FA y Cs 1–x–y PbBr 3 , MA x FA y Cs 1–x–y PbI 3 , Cs x FA y MA 1–x–y Pb(Br x+y I 1–x–y ) 3 , and Cs x MA y FA 1–x–y Pb(I x+y Br 1–x–y ) 3 . Non-negative matrix factorization and Gaussian process regression are used to interpolate the photoluminescent behavior of the phase diagram. This interpolative regression analysis helps to distinguish mixtures that form solid solutions from those that segregate into multiple materials, pointing out the most stable regions of the phase diagram. Here, we find stability dependence on composition to be nonuniform within the composition space, suggesting the presence of potential preferential compositional regions. This proposed workflow is universal and can be applied to other solution-processable materials.

36 MATERIALS SCIENCE↗

Comparison and Interpretation of Admittance Spectroscopy and Deep Level Transient Spectroscopy from Co-Evaporated and Solution-Deposited Cu2ZnSn(Sx, Se1-x)4 Solar Cells

Cu2ZnSn(S, Se)4 (CZTSe) is an earth-abundant semiconductor with potential for economical thin-film photovoltaic devices. Short minority carrier lifetimes contribute to low open circuit voltage and efficiency. Deep level defects that may contribute to lower minority carrier lifetimes in kesterites have been theoretically predicted, however very little experimental characterization of these deep defects exists. In this work we use admittance spectroscopy (AS) and deep level transient spectroscopy (DLTS) to characterize devices built using CZTSSe absorber layers deposited via both coevaporation and solution processing. AS reveals a band of widely-distributed activation energies for traps or energy barriers for transport, especially in the solution deposited case. DLTS reveals signatures of deep majority and minority traps within both types of samples.

14 SOLAR ENERGY↗

Should Pruning be a Pre-Processor of any Linear System?

There are many real-world problems whose mathematical models turn out to be linear systems Ax = b , where A is an m by x n matrix. Each equation of the linear system is an information. An information, in a physical problem, such as 4 mangoes, 6 bananas, and 5 oranges cost $10, is mathematically modeled as 4x(sub 1) + 6x(sub 2) + 5x (sub 3) = 10, where x(sub 1), x(sub 2), x(sub 3) are each cost of one mango, that of one banana, and that of one orange, respectively. All the information put together in a specified context, constitutes the physical problem and need not be all distinct. Some of these could be redundant, which cannot be readily identified by inspection. The resulting mathematical model will thus have equations corresponding to this redundant information and hence are linearly dependent and thus superfluous. Consequently, these equations once identified should be better pruned in the process of solving the system. The benefits are (i) less computation and hence less error and consequently a better quality of solution and (ii) reduced storage requirements. In literature, the pruning concept is not in vogue so far although it is most desirable. In a numerical linear system, the system could be slightly inconsistent or inconsistent of varying degree. If the system is too inconsistent, then we should fall back on to the physical problem (PP), check the correctness of the PP derived from the material universe, modify it, if necessary, and then check the corresponding mathematical model (MM) and correct it. In nature/material universe, inconsistency is completely nonexistent. If the MM becomes inconsistent, it could be due to error introduced by the concerned measuring device and/or due to assumptions made on the PP to obtain an MM which is relatively easily solvable or simply due to human error. No measuring device can usually measure a quantity with an accuracy greater that 0.005% or, equivalently with a relative error less than 0.005%. Hence measurement error is unavoidable in a numerical linear system when the quantities are continuous (or even discrete with extremely large number). Assumptions, though not desirable, are usually made when we find the problem sufficiently difficult to be solved within the available means/tools/resources and hence distort the PP and the corresponding MM. The error thus introduced in the system could (not always necessarily though) make the system somewhat inconsistent. If the inconsistency (contradiction) is too much then one should definitely not proceed to solve the system in terms of getting a least-squares solution or a minimum norm solution or the minimum-norm least-squares solution. All these solutions will be invariably of no real-world use. If, on the other hand, inconsistency is reasonably low, i.e. the system is near-consistent or, equivalently, has near-linearly-dependent rows, then the foregoing solutions are useful. Pruning in such a near-consistent system should be performed based on the desired accuracy and on the definition of near-linear dependence. In this article, we discuss pruning over various kinds of linear systems and strongly suggest its use as a pre-processor or as a part of an algorithm. Ideally pruning should (i) be a part of the solution process (algorithm) of the system, (ii) reduce both computational error and complexity of the process, and (iii) take into account the numerical zero defined in the context. These are precisely what we achieve through our proposed O(mn2) algorithm presented in Matlab, that uses a subprogram of solving a single linear equation and that has embedded in it the pruning.

Sen, Syamal K.↗

Should Pruning be a Pre-Processor of any Linear System?

There are many real-world problems whose mathematical models turn out to be linear systems Ax = b, where A is an m x n matrix. Each equation of the linear system is an information. An information, in a physical problem, such as 4 mangoes, 6 bananas, and 5 oranges cost $10, is mathematically modeled as an equation 4x(sub 1) + 6x(sub 2) + 5x(sub 3) = 10 , where x(sub 1), x(sub 2), x(sub 3) are each cost of one mango, that of one banana, and that of one orange, respectively. All the information put together in a specified context, constitutes the physical problem and need not be all distinct. Some of these could be redundant, which cannot be readily identified by inspection. The resulting mathematical model will thus have equations corresponding to this redundant information and hence are linearly dependent and thus superfluous. Consequently, these equations once identified should be better pruned in the process of solving the system. The benefits are (i) less computation and hence less error and consequently a better quality of solution and (ii) reduced storage requirements. In literature, the pruning concept is not in vogue so far although it is most desirable. It is assumed that at least one information, i.e. one equation is known to be correct and which will be our first equation. In a numerical linear system, the system could be slightly inconsistent or inconsistent of varying degree. If the system is too inconsistent, then we should fall back on to the physical problem (PP), check the correctness of the PP derived from the material universe, modify it, if necessary, and then check the corresponding mathematical model (MM) and correct it. In nature/material universe, inconsistency is completely nonexistent. If the MM becomes inconsistent, it could be due to error introduced by the concerned measuring device and/or due to assumptions made on the PP to obtain an MM which is relatively easily solvable or simply due to human error. No measuring device can usually measure a quantity with an accuracy greater that 0.005% or, equivalently with a relative error less than 0.005%. Hence measurement error is unavoidable in a numerical linear system when the quantities are continuous (or even discrete with extremely large number). Assumptions, though not desirable, are usually made when we find the problem sufficiently difficult to be solved within the available means/tools/resources and hence distort the PP and the corresponding MM. The . error thus introduced in the system could (not always necessarily though) make the system somewhat inconsistent. If the inconsistency (contradiction) is too much then one should definitely not proceed to solve the system in terms of getting a least-squares solution or the minimum-norm least-squares solution. All these solutions will be invariably of no real-world use. If, on the other hand, inconsistency is reasonably low, i.e. the system is near-consistent or, equivalently, has near-linearly-dependent rows, then the foregoing solutions are useful. Pruning in such a near-consistent system should be performed based on the desired accuracy and on the definition of near-linear dependence. In this article, we discuss pruning over various kinds of linear systems and strongly suggest its use as a pre-processor or as a part of an algorithm. Ideally pruning should (i) be a part of the solution process (algorithm) of the system, (ii) reduce both computational error and complexity of the process, and (iii) take into account the numerical zero defined in the context. These are precisely what we achieve through our proposed O(mn2) algorithm presented in Matlab, that uses a subprogram of solving a single linear equation and that has embedded in it the pruning.

Sen, Syamal K.↗

Automation of a N-S S and C Database Generation for the Harrier in Ground Effect

A method of automating the generation of a time-dependent, Navier-Stokes static stability and control database for the Harrier aircraft in ground effect is outlined. Reusable, lightweight components arc described which allow different facets of the computational fluid dynamic simulation process to utilize a consistent interface to a remote database. These components also allow changes and customizations to easily be facilitated into the solution process to enhance performance, without relying upon third-party support. An analysis of the multi-level parallel solver OVERFLOW-MLP is presented, and the results indicate that it is feasible to utilize large numbers of processors (= 100) even with a grid system with relatively small number of cells (= 10(exp 6)). A more detailed discussion of the simulation process, as well as refined data for the scaling of the OVERFLOW-MLP flow solver will be included in the full paper.

Murman, Scott M.↗

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

The Brine Residual In-Containment (BRIC) concept was developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying for these solutions. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management in spacecraft brine dewatering system designs. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other observations from testing are reported.

Callahan, Michael R.↗

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

The Brine Residual In-Containment (BRIC) concept is being developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management designs typically used in spacecraft systems. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches currently envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other early observations from testing are reported.

Callahan, Michael R.↗

Green solvent-processable poly(3-hexylthiophene) derivative maintains high hole mobility in diodes

The development of environmentally sustainable fabrication methods for organic solar cells (OSCs) is critical to enable their large-scale adoption. Conventional solution-processed OSCs often rely on halogenated, toxic solvents that pose health and environmental risks, limiting their scalability. This is because π-conjugated polymers tend to have a low solubility in non-halogenated solvents. A common strategy to enhance solubility in alternative solvents is through the incorporation of polar solubilizing groups, often on every repeat unit of at least one monomer. However, too many polar side chains tend to disrupt favorable morphology and decrease charge transport properties. In this study, we demonstrate that a minimal degree of side chain functionalization can improve green solvent processability while preserving electrical performance. We tested this hypothesis using our previously reported random copolymer derivative of poly(3-hexylthiophene) (P3HT) where ∼10 mol% of the side chains are 6-pentanoatehexyl side chains. We find that this low-level functionalization significantly broadens the solvents that can be used to process P3HT to less toxic solvents such as o-xylene and anisole. Furthermore, the copolymer processed from greener solvents showed high hole mobilities (∼10⁻ 3 cm 2 /Vs by the Space-Charge Limiting Current method in diodes), comparable to P3HT films cast from toxic chloroform. These findings suggest that minimal side-chain modification is a viable strategy for expanding green solvent compatibility while preserving electrical performance, paving the way toward more sustainable organic semiconductor designs.

36 MATERIALS SCIENCE↗

Hydrazine-Free Solution-Deposited CuIn(S,Se)2 Solar Cells by Spray Deposition of Metal Chalcogenides

Solution processing of semiconductors, such as CuInSe2 and its alloys (CIGS), can significantly reduce the manufacturing costs of thin film solar cells. Despite the recent success of solution deposition approaches for CIGS, toxic reagents such as hydrazine are usually involved, which introduce health and safety concerns. Here, we present a simple and safer methodology for the preparation of high-quality CuIn(S, Se)2 absorbers from metal sulfide solutions in a diamine/dithiol mixture. The solutions are sprayed in air, using a chromatography atomizer, followed by a postdeposition selenization step. Two different selenization methods are explored resulting in power conversion efficiencies of up to 8%.

14 SOLAR ENERGY↗

Confined cooperative self-assembly and synthesis of optically and electrically active nanostructures : final LDRD report

In this project, we developed a confined cooperative self-assembly process to synthesize one-dimensional (1D) j-aggregates including nanowires and nanorods with controlled diameters and aspect ratios. The facile and versatile aqueous solution process assimilates photo-active macrocyclic building blocks inside surfactant micelles, forming stable single-crystalline high surface area nanoporous frameworks with well-defined external morphology defined by the building block packing. Characterizations using TEM, SEM, XRD, N{sub 2} and NO sorption isotherms, TGA, UV-vis spectroscopy, and fluorescence imaging and spectroscopy indicate that the j-aggregate nanostructures are monodisperse and may further assemble into hierarchical arrays with multi-modal functional pores. The nanostructures exhibit enhanced and collective optical properties over the individual chromophores. This project was a small footprint research effort which, nonetheless, produced significant progress towards both the stated goal as well as unanticipated research directions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

NOA: A Scalable Multi-Parent Clustering Hierarchy for WSNs

NOA is a multi-parent, N-tiered, hierarchical clustering algorithm that provides a scalable, robust and reliable solution to autonomous configuration of large-scale wireless sensor networks. The novel clustering hierarchy's inherent benefits can be utilized by in-network data processing techniques to provide equally robust, reliable and scalable in-network data processing solutions capable of reducing the amount of data sent to sinks. Utilizing a multi-parent framework, NOA reduces the cost of network setup when compared to hierarchical beaconing solutions by removing the expense of r-hop broadcasting (r is the radius of the cluster) needed to build the network and instead passes network topology information among shared children. NOA2, a two-parent clustering hierarchy solution, and NOA3, the three-parent variant, saw up to an 83% and 72% reduction in overhead, respectively, when compared to performing one round of a one-parent hierarchical beaconing, as well as 92% and 88% less overhead when compared to one round of two- and three-parent hierarchical beaconing hierarchy.

99 GENERAL AND MISCELLANEOUS↗

Multi-scale ordering in highly stretchable polymer semiconducting films

Stretchable semiconducting polymers have been developed as a key component to enable skin-like wearable electronics, but their electrical performance must be improved to enable more advanced functionalities. Here, we report a solution processing approach that can achieve multi-scale ordering and alignment of conjugated polymers in stretchable semiconductors to substantially improve their charge carrier mobility. Using solution shearing with a patterned microtrench coating blade, macroscale alignment of conjugated-polymer nanostructures was achieved along the charge transport direction. In conjunction, the nanoscale spatial confinement aligns chain conformation and promotes short-range π–π ordering, substantially reducing the energetic barrier for charge carrier transport. As a result, the mobilities of stretchable conjugated-polymer films have been enhanced up to threefold and maintained under a strain up to 100%. This method may also serve as the basis for large-area manufacturing of stretchable semiconducting films, as demonstrated by the roll-to-roll coating of metre-scale films.

36 MATERIALS SCIENCE↗