Search NASA⌕ Search

SEARCH · Search NASA

Results for “space shuttles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Study to investigate and evaluate means of optimizing the Ku-band combined radar/communication functions for the space shuttle

The performance of the space shuttle orbiter's Ku-Band integrated radar and communications equipment is analyzed for the radar mode of operation. The block diagram of the rendezvous radar subsystem is described. Power budgets for passive target detection are calculated, based on the estimated values of system losses. Requirements for processing of radar signals in the search and track modes are examined. Time multiplexed, single-channel, angle tracking of passive scintillating targets is analyzed. Radar performance in the presence of main lobe ground clutter is considered and candidate techniques for clutter suppression are discussed. Principal system parameter drivers are examined for the case of stationkeeping at ranges comparable to target dimension. Candidate ranging waveforms for short range operation are analyzed and compared. The logarithmic error discriminant utilized for range, range rate and angle tracking is formulated and applied to the quantitative analysis of radar subsystem tracking loops.

Weber, C. L.↗
NASA NTRS1978

The effect of normal atmospheric variability on Space Shuttle Orbiter entry performance

The Space Shuttle Orbiter is controlled during entry by a combination of aerodynamic surfaces composed of elevons, a body flap, and a rudder that flares as a speedbrake, and a reaction control system that uses 16 small rocket thrusters. To determine the effects of realistic atmospheric density variations on reentry, a series of Monte Carlo trajectories were generated for each season. The performance parameters analyzed include maximum hinge moments experienced by the aerodynamic control surfaces, the maximum deflections experienced by the aerodynamic control surfaces, a range of angle-of-sideslip values, maximum dynamic pressure, maximum stagnation point heat rate, and state conditions at touchdown. The results of the investigation indicate that the Orbiter guidance and control systems could tolerate atmospheric variability without failures in the control system hardware.

Powell, R. W.↗
NASA NTRS1979

Space Shuttle - Now and later

The Space Shuttle System consisting of four major elements, the orbiter, three main engines, an expendable external tank, and solid rocket boosters is examined. Dimensions, thrust and payload capacity are observed, noting cost reduction through recovery and subsequent reuse of some components. Return of the solid rocket boosters (SRB's) via parachute and recovery from the ocean for refurbishment is covered. Objectives for the first mission scheduled for November 1979 include achieving a 150 nautical mile orbit and carrying a payload consisting of development flight instrumentation (DFI), the induced environment contamination monitor (IECM), and the aerodynamic coefficients identification package (ACIP). A section devoted to performance enhancement, discusses weight reduction on the orbiter, external tanks and thrust augmentation through the use of strap on solid motors (SOSM).

Malkin, M. S.↗
NASA NTRS1981

The Space Shuttle

The development of the Space Shuttle is traced. Aerodynamic loads and dynamic characteristics, structural design, ascent and entry heating profiles, and propulsion systems are discussed. Problems in the area of systems management and flight control during entry and in the design of an effective thermal control system are discussed in detail.

Faget, M. A.↗
NASA NTRS1982

Flight measurements of tile gap heating on the Space Shuttle

Data are presented from Space Shuttle flight measurements of the temperature distribution within the gaps of the reusable surface insulation tiles. This is the first of a series of flight measurements in which the gap width and tile surface edge radius will be systematically varied. The data show several interesting features including the time and effect of boundary-layer transition. The local heating rates into the gap surfaces are calculated from the measured temperature distribution down the gap at two locations.

Pitts, W. C.↗
NASA NTRS1985

Space shuttle wheels and brakes

The Space Shuttle Orbiter wheels were subjected to a combination of tests which are different than any previously conducted in the aerospace industry. The major testing difference is the computer generated dynamic landing profiles used during the certification process which subjected the wheels and tires to simulated landing loading conditions. The orbiter brakes use a unique combination of carbon composite linings and beryllium heat sink to minimize weight. The development of a new lining retention method was necessary in order to withstand the high temperature generated during the braking roll. As with many programs, the volume into which this hardware had to fit was established early in the program, with no provisions made for growth to offset the continuously increasing predicted orbiter landing weight.

Carsley, R. B.↗
NASA NTRS1987

Inhibited interferon-gamma but normal interleukin-3 production from rats flown on the Space Shuttle

Rats were flown on Space Shuttle SL-3 for one week. When spleen cells were removed from these rats and challenged with concanavalin-A, interferon-gamma production was severely inhibited, while interleukin-3 production was unaffected compared to ground-based control rats. These data indicate that there is a defect in interferon-gamma production in rats that have been exposed to spaceflight. This defect could contribute to, and be one reason for, immunosuppression observed after spaceflight.

Gould, Cheryl L.↗
NASA NTRS1989

Power from the Space Shuttle

The use of the Space Shuttle to provide avionics and electrical power accommodations to a large dedicated payload and/or to multiple smaller payloads throughout the flight is studied. The payload equipment can be mounted in the Shuttle Orbiter aft flight deck and middeck portions of the crew cabins and in the Orbiter cargo bay. The Orbiter provides avionics services to the following major payload classes: the single-section payload, the small payload, the middeck payload, and the Get-Away Special payload.

Speier, William M.↗
NASA NTRS1991

Lightning current rate of rise in the new lightning flash model for the space shuttle program

The recently baselined Space Shuttle lightning effects flash model is discussed. The discussion is limited to the current rate(s) of rise. A review of some of the recent data is presented, as well as a discussion of how interaction processes affect the induced voltages and currents which arise from a lightning strike. It is concluded that the multiple pulse components of the new flash model present a more severe threat to complex avionic systems, than is presented by a single pulse having an extremely fast rate of rise.

Bankston, Nathaniel G.↗
NASA NTRS1991

Observations of the Earth in polarized light from the US Space Shuttle

During the four American Space Shuttle missions of year 1985, the crewmembers took pictures of the Earth in polarized light. Different problems were encountered in the quantitative use of the data: induced polarization by the shuttle window, lack of calibration correction of the window polarization and enveloped in flight calibration methods. The analysis of the selected data first confirmed the previous observation over snow and sand. A low polarization on these surfaces was observed. On the other hand, the measurements show the potentiability of the polarization for agricultural inventory. Contamination of the atmosphere is well characterized.

Roger, Jean-Claude↗
NASA NTRS1992

Design of a resistive exercise device for use on the Space Shuttle

The National Aeronautics and Space Administration in conjunction with the Universities Space Research Association sponsored the design of a Resistive Exercise Device (RED) for use on the Space Shuttle. The device must enable the astronauts to perform a number of exercises to prevent skeletal muscle atrophy and neuromuscular deconditioning in microgravity environments. The RED must fit the requirements for limited volume and weight and must provide a means of restraint during exercise. The design team divided the functions of the device into three major groups: methods of supplying force, methods of adjusting force, and methods of transmitting the force to the user. After analyzing the three main functions of the RED and developing alternatives for each, the design team used a comparative decision process to choose the most feasible components for the overall design. The design team selected the constant force spring alternative for further embodiment. The device consists of an array of different sized constant force springs which can be pinned in different combinations to produce the required output forces. The force is transmitted by means of a shaft and gear system. The final report is divided into four sections. An introduction section discusses the sponsor background, problem background and requirements of the device. The second section covers the alternative designs for each of the main functions. The design solution and pertinent calculations comprises the third section. The final section contains design conclusions and recommendations including topics of future work.

Carlson, Dennis L.↗
NASA NTRS1992

A mobile robot system for ground servicing operations on the space shuttle

A mobile system for space shuttle servicing, the Tessellator, has been configured, designed and is currently being built and integrated. Robot tasks include chemical injection and inspection of the shuttle's thermal protection system. This paper outlines tasks, rationale, and facility requirements for the development of this system. A detailed look at the mobile system and manipulator follow with a look at mechanics, electronics, and software. Salient features of the mobile robot include omnidirectionality, high reach, high stiffness and accuracy with safety and self-reliance integral to all aspects of the design. The robot system is shown to meet task, facility, and NASA requirements in its design resulting in unprecedented specifications for a mobile-manipulation system.

Dowling, K.↗
NASA NTRS2000

Friction Plug Weld Repair for the Space Shuttle External Tank

Lockheed Martin Space Systems, Michoud Operations in New Orleans, LA is the manufacturer of the External Fuel Tanks (ET) for the Space Transportation System (STS). The ET contains and delivers the propellants used by the Orbiters three main engines. Additionally, it also serves as the structural backbone for the Orbiter and the two Solid Rocket Boosters (SRB), which combined, constitute the STS. In 1994, NASA established that in order to launch the International Space Station, the performance of the STS must be improved. One option was to reduce the weight of the ET, which would enable sufficient increase in performance. With the development of the Weldalite(R) series of Al-Cu-Li alloys in the late 1980's, Lockheed Martin was postured to replace the current A12219 fuel tanks with the high strength, light weight A12195 alloy. With the use of A12195 and some component redesign, the weight of the Super Lightweight (SLWT) ET was reduced by approximately 7,000 pounds, which added as much capability to the Space Shuttle. Since June 1998, seven STS missions have been successful with the use of the SLWT ET's.

Hartley, Paula J.↗
NASA NTRS2005

The Application of Electron Microscopy Techniques to the Space Shuttle Columbia Accident Investigation

The Space Shuttle Columbia was returning from a 16-day research mission, STS- 107, with nominal system performance prior to the beginning of the entry interface into earth's upper atmosphere. Approximately one minute and twenty four seconds into the peak heating region of the entry interface, an off-nominal temperature rise was observed in the left main landing gear brake line. Nearly seven minutes later, all contact was lost with Columbia. Debris was observed periodically exiting the Shuttle's flight path throughout the reentry profile over California, Nevada, and New Mexico, until its final breakup over Texas. During the subsequent investigation, electron microscopy techniques were crucial in revealing the location of the fatal damage that resulted in the loss of Columbia and her crew.

Shah, Sandeep↗
NASA NTRS2005

Techniques and Tools of NASA's Space Shuttle Columbia Accident Investigation

The Space Shuttle Columbia accident investigation was a fusion of many disciplines into a single effort. From the recovery and reconstruction of the debris, Figure 1, to the analysis, both destructive and nondestructive, of chemical and metallurgical samples, Figure 2, a multitude of analytical techniques and tools were employed. Destructive and non-destructive testing were utilized in tandem to determine if a breach in the left wing of the Orbiter had occurred, and if so, the path of the resultant high temperature plasma flow. Nondestructive analysis included topometric scanning, laser mapping, and real-time radiography. These techniques were useful in constructing a three dimensional virtual representation of the reconstruction project, specifically the left wing leading edge reinforced carbon/carbon heat protectant panels. Similarly, they were beneficial in determining where sampling should be performed on the debris. Analytic testing included such techniques as Energy Dispersive Electron Microprobe Analysis (EMPA), Electron Spectroscopy Chemical Analysis (ESCA), and X-Ray dot mapping; these techniques related the characteristics of intermetallics deposited on the leading edge of the left wing adjacent to the location of a suspected plasma breach during reentry. The methods and results of the various analyses, along with their implications into the accident, are discussed, along with the findings and recommendations of the Columbia Accident Investigation Board. Likewise, NASA's Return To Flight efforts are highlighted.

McDanels, Steve J.↗
NASA NTRS2007

Experimental Design for the Evaluation of Detection Techniques of Hidden Corrosion Beneath the Thermal Protective System of the Space Shuttle Orbiter

The United States Space Operational Space Shuttle Fleet Consists of three shuttles with an average age of 19.7 years. Shuttles are exposed to corrosive conditions while undergoing final closeout for missions at the launch pad and extreme conditions during ascent, orbit, and descent that may accelerate the corrosion process. Structural corrosion under TPS could progress undetected (without tile removal) and eventually result in reduction in structural capability sufficient to create negative margins of . safety and ultimate loss of local structural capability.

Kammerer, Catherine C.↗