Search NASA⌕ Search

SEARCH · Search NASA

Results for “tough”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Post Irradiation Examination of Pressurized Water Reactor Stainless Steel Internal Components

Internal structural components of pressurized water reactors (PWR), such as baffle former bolts, are subjected to significant neutron irradiation and mechanical stresses at elevated temperatures during plant operation. Over the long operation of the power plant, these conditions lead to potential degradation and reduced load-carrying capacity of these bolts. To understand property degradation more fully, to confirm the results of experimental irradiation programs, and to predict operational lifetime performance of structural materials in internal components, post irradiation examination of harvested materials from operating nuclear reactors is required. In this work, two high fluence 316 stainless steel baffle former bolts were retrieved from a commercial Westinghouse two-loop downflow type PWR and then sectioned for analysis via mechanical testing and microstructural characterization. The irradiation damage fluctuated along the bolt length with damage levels from 15 to 41 displacements per atom with the bolt head receiving approximately twice the neutron damage levels as that of the bolt thread section. Mechanical testing evaluations showed extensive irradiation hardening and a sharp decrease in fracture toughness in all parts of the bolt, though with limited variation along the bolt length. Microstructural characterization using analytical scanning transmission electron microscopy and atom probe tomography showed significant radiation induced precipitation, segregation, and dislocation loop and cavity formation. However, unlike the mechanical behavior, there was considerable variation along the bolt length but opposite of what may be expected, with more precipitation and cavity formation in the bolt thread where the neutron radiation dose is less than in the bolt head where the neutron radiation dose is higher. The cause of this variation is likely due to gradients in temperature, neutron energy spectra, and gamma irradiation.

Lach, Tim↗
DOE OSTI2022

Understanding the Elastic, Plastic, and Damage Features in Fracturing of Self-reinforced Thermoplastic Composites via Non-destructive Digital Imaging Correlation

This work demonstrated the utilization of non-destructive Digital Imaging Correlation (DIC) method to characterize the elastic, plastic, and damage features during the Mode I intra-laminar fracturing process of self-reinforced thermoplastic composites by using a self-reinforced polypropylene (PP) composite as an example. The DIC results clearly showed the development of huge plastic zone (PZ) and non-negligible Fracture Process Zone (FPZ) in front of the notch tip during the fracturing process, and the geometries and sizes of the foregoing zones at the peak load were further quantified. Such an interesting fracturing behavior of self-reinforced thermoplastic composites is way different from brittle materials (e.g., glass, acrylic, etc.), ductile materials (e.g., aluminum, steel, etc.), and even quasi-brittle materials (e.g., concrete, nanoparticle-reinforced composites, tough ceramics, wood, cement, carbon/glass fiber-reinforced polymers, etc.). Thus, understanding the elastic, plastic, and damage features is the first step before better characterizing the material fracture properties of self-reinforced thermoplastic composites through new analytical methods and computational modeling. These efforts are of utmost importance for wide applications of self-reinforced thermoplastic composites in various engineering fields in the future.

Lightweight Composites, Self-reinforced Thermoplas↗
DOE OSTI2021

Amorphization in extreme deformation of the CrMnFeCoNi high-entropy alloy

Ever-harsher service conditions in the future will call for materials with increasing ability to undergo deformation without sustaining damage while retaining high strength. Prime candidates for these conditions are certain high-entropy alloys (HEAs), which have extraordinary work-hardening ability and toughness. By subjecting the equiatomic CrMnFeCoNi HEA to severe plastic deformation through swaging followed by either quasi-static compression or dynamic deformation in shear, we observe a dense structure comprising stacking faults, twins, transformation from the face-centered cubic to the hexagonal close-packed structure, and, of particular note, amorphization. The coordinated propagation of stacking faults and twins along {111} planes generates high-deformation regions, which can reorganize into hexagonal packets; when the defect density in these regions reaches a critical level, they generate islands of amorphous material. These regions can have outstanding mechanical properties, which provide additional strengthening and/or toughening mechanisms to enhance the capability of these alloys to withstand extreme loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Knots are not for naught: Design, properties, and topology of hierarchical intertwined microarchitected materials

Lightweight and tough engineered materials are often designed with three-dimensional hierarchy and interconnected structural members whose junctions are detrimental to their performance because they serve as stress concentrations for damage accumulation and lower mechanical resilience. We introduce a previously unexplored class of architected materials, whose components are interwoven and contain no junctions, and incorporate micro-knots as building blocks within these hierarchical networks. Tensile experiments, which show close quantitative agreements with an analytical model for overhand knots, reveal that knot topology allows a new regime of deformation capable of shape retention, leading to a ~92% increase in absorbed energy and an up to ~107% increase in failure strain compared to woven structures, along with an up to ~11% increase in specific energy density compared to topologically similar monolithic lattices. Our exploration unlocks knotting and frictional contact to create highly extensible low-density materials with tunable shape reconfiguration and energy absorption capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Deformation and failure of the CrCoNi medium-entropy alloy subjected to extreme shock loading

The extraordinary work hardening ability and fracture toughness of the face-centered cubic (fcc) high-entropy alloys render them ideal candidates for many structural applications. Here, the deformation and failure mechanisms of an equiatomic CrCoNi medium-entropyalloy (MEA) were investigated by powerful laser-driven shock experiments. Multiscale characterization demonstrates that profuse planar defects including stacking faults, nanotwins, and hexagonal nanolamella were generated during shock compression, forming a three-dimensional network. During shock release, the MEA fractured by strong tensile deformation and numerous voids was observed in the vicinity of the fracture plane. High defect populations, nanorecrystallization, and amorphization were found adjacent to these areas of localized deformation. Molecular dynamics simulations corroborate the experimental results and suggest that deformation-induced defects formed before void nucleation govern the geometry of void growth and delay their coalescence. Our results indicate that the CrCoNi-based alloys are impact resistant, damage tolerant, and potentially suitable in applications under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Chemically recyclable thermoplastics from reversible-deactivation polymerization of cyclic acetals

Identifying plastics capable of chemical recycling to monomer (CRM) is the foremost challenge in creating a sustainable circular plastic economy. Polyacetals are promising candidates for CRM but lack useful tensile strengths owing to the low molecular weights produced using current uncontrolled cationic ring-opening polymerization (CROP) methods. Here, we present reversible-deactivation CROP of cyclic acetals using a commercial halomethyl ether initiator and an indium(III) bromide catalyst. Using this method, we synthesize poly(1,3-dioxolane) (PDXL), which demonstrates tensile strength comparable to some commodity polyolefins. Depolymerization of PDXL using strong acid catalysts returns monomer in near-quantitative yield and even proceeds from a commodity plastic waste mixture. Our efficient polymerization method affords a tough thermoplastic that can undergo selective depolymerization to monomer.

Abel, Brooks A.↗
DOE OSTI2025

C60-Based Ionic Salt Electron Shuttle for High-Performance Inverted Perovskite Solar Modules

Although C60 is usually the electron transport layer (ETL) in inverted perovskite solar cells, its molecular nature of C60 leads to weak interfaces that lead to non-ideal interfacial electronic and mechanical degradation. Here, we synthesized an ionic salt from C60, 4-(1',5'-dihydro-1'-methyl-2'H-[5,6] fullereno-C60-Ih-[1,9-c]pyrrol-2'-yl) phenylmethanaminium chloride (CPMAC), and used it as the electron shuttle in inverted PSCs. The CH2-NH3+ head group in the CPMA cation improved the ETL interface and the ionic nature enhanced the packing, leading to ~3-fold increase in the interfacial toughness compared to C60. Using CPMAC, we obtained ~26% power conversion efficiencies (PCEs) with ~2% degradation after 2,100 hours of 1-sun operation at 65degrees C. For minimodules (four subcells, 6 centimeters square), we achieved the PCE of ~23% with <9% degradation after 2,200 hours of operation at 55degrees C.

14 SOLAR ENERGY↗
DOE OSTI2020

Frontiers in the Simulation of Dislocations

Dislocations play a vital role in the mechanical behavior of crystalline materials during deformation. To capture dislocation phenomena across all relevant scales, a multiscale modeling framework of plasticity has emerged, with the goal of reaching a quantitative understanding of microstructure–property relations, for instance, to predict the strength and toughness of metals and alloys for engineering applications. This review describes the state of the art of the major dislocation modeling techniques, and then discusses how recent progress can be leveraged to advance the frontiers in simulations of dislocations. Furthermore, the frontiers of dislocation modeling include opportunities to establish quantitative connections between the scales, validate models against experiments, and use data science methods (e.g., machine learning) to gain an understanding of and enhance the current predictive capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Optimization of thermal barrier coating performance and durability over a drive cycle

A methodology to thermo-mechanically optimize a piston thermal barrier coating over a full drive cycle was established. The optimization objective was to minimize the heat transfer to the engine wall while maintaining structural integrity of the coating. Over 800 candidate materials were investigated and the optimization required more than one million non-road transient drive cycle calculations; real materials were investigated to ensure a realizable result and the existence of thermal and mechanical properties. High computational efficiency was achieved using a recently developed analytical heat transfer technique for multilayer engine walls. An uncoupled approach was utilized for the optimization, wherein the gas temperature and heat transfer coefficient profiles from a fully coupled and calibrated baseline model over the 20-min drive cycle were employed. The coating/piston interface temperature was constrained to be below the maximum piston service temperature limit. The durability was assessed using a recently developed analytical coating delamination framework for engine in-cylinder coatings based on the energy release rate when a crack forms. Results are presented for a mechanically unconstrained optimization and for cases constrained to three fixed levels of drive-cycle maximum energy release rate, and also constrained by the individual material’s toughness. The best-performing coating materials identified were verified using the fully coupled system-level model, which compared well to the uncoupled predictions. A study on the effect of adding a sealing layer to some high-performing, but porous, coatings showed a reduction in fuel consumption benefit and an increased exhaust temperature over the cycle, but the system still outperformed the uncoated case. The results of the study elucidate the importance of including engine performance and mechanical failure considerations in thermal barrier coating design.

Engineering↗
DOE OSTI2021

Remote sensing detection enhancement

Big Data in the area of Remote Sensing has been growing rapidly. Remote sensors are used in surveillance, security, traffic, environmental monitoring, and autonomous sensing. Real-time detection of small moving targets using a remote sensor is an ongoing, challenging problem. Since the object is located far away from the sensor, the object often appears too small. The object’s signal-to-noise-ratio (SNR) is often very low. Occurrences such as camera motion, moving backgrounds (e.g., rustling leaves), low contrast and resolution of foreground objects makes it difficult to segment out the targeted moving objects of interest. Due to the limited appearance of the target, it is tough to obtain the target’s characteristics such as its shape and texture. Without these characteristics, filtering out false detections can be a difficult task. Detecting these targets, would often require the detector to operate under a low detection threshold. However, lowering the detection threshold could lead to an increase of false alarms. In this paper, the author will introduce a new method that improves the probability to detect low SNR objects, while decreasing the number of false alarms as compared to using the traditional baseline detection technique.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Influence of Agricultural Managed Aquifer Recharge (AgMAR) and Stratigraphic Heterogeneities on Nitrate Reduction in the Deep Subsurface

This data package contains input files for TOUGHREACT for a modeling study examining the effects of managed aquifer recharge on agricultural lands on nitrate cycling and transport in the Central Valley of CA near Modesto. The files contain all the geochemical species, reactions, and hydrological parameters for the model. The files are text files used for the TOUGH family of code created by LBNL. To use the files a license is required. https://tough.lbl.gov/licensing-download/toughreact-licensing-download/Accompanying Paper Abstract: Agricultural managed aquifer recharge (AgMAR) is a proposed management strategy whereby surface water flows are used to intentionally flood croplands with the purpose of recharging underlying aquifers. However, legacy nitrate (NO3-) contamination in agriculturally-intensive regions poses a threat to groundwater resources under AgMAR. To address these concerns, we use a reactive transport modeling framework to better understand the effects of AgMAR management strategies (i.e., by varying the frequency, duration between flooding events, and amount of water) on N leaching to groundwater under different stratigraphic configurations and antecedent moisture conditions. In particular, we examine the potential of denitrification and nitrogen retention in deep vadose zone sediments (~15 m) using variable AgMAR application rates on two-dimensional representations of differently textured soils, soils with discontinuous bands/channels, and soils with preferential flow paths characteristic of typical agricultural field sites. Our results indicate that finer textured sediments, such as silt loams, alone or embedded within high flow regions, are important reducing zones providing conditions needed for denitrification. Simulation results further suggest that applying water all-at-once rather than in increments for a fixed volume of recharge transports higher concentrations of NO3- deeper into the profile, which has the potential to exacerbate groundwater quality. This transport into deeper depths can be aggravated by wetter antecedent soil moisture conditions. However, applying water all-at-once also increases denitrification within the vadose zone by promoting anoxic conditions. We conclude that AgMAR management strategies can be designed to enhance denitrification in the subsurface and reduce N leaching to groundwater, while specifically accounting for lithologic heterogeneity, antecedent soil moisture conditions, and depth to the water table. Our findings are potentially relevant to other systems that experience flooding inundation such as riparian corridors, floodplains, wetlands, and other managed landscapes like dedicated recharge basins.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Fracture properties of high-entropy alloys

Abstract Since the concept of high-entropy alloys (HEAs) as materials with at least four or five principal elements in (near)-equiatomic composition was introduced in 2004, this new class of materials has penetrated essentially all materials science-related fields. The main reason for this is that some face-centered-cubic alloy compositions have been shown to exhibit truly outstanding mechanical properties with extraordinary combinations of strength, ductility, and fracture toughness, particularly at cryogenic temperatures, whereas certain body-centered-cubic refractory compositions display remarkable high-temperature strength. While significant efforts have been put into rapid screening and narrowing the compositional space of HEAs to a manageable scope, there are still only a few metallic alloys that push the limits of mechanical performance. Here, we review work on some of the most damage-tolerant HEAs discovered to date and discuss the fundamental reasons why their resistance to fracture and subsequent stable crack growth is so exceptional. Graphical abstract

Gludovatz, Bernd (ORCID:0000000224203879)↗
DOE OSTI2021

Resistance to fracture in the glassy solid electrolyte Lipon

We report on the mechanical behavior of a solid Li-ion conductor, lithium phosphorous oxynitride (Lipon), for solid-state batteries. In particular, the purpose of this investigation was to quantify the resistance to cracking (fracture toughness) of this material by nanoindentation. We observed surprising ductility and the ability to recover in Lipon. We were unsuccessful in inducing cracks in Lipon and observed accommodation of stress via pile-up and densification rather than by cracking at various strain rates. Simulations demonstrate that both deformation and densification depend on the alkali content. Densification appears to be recoverable at room temperature. We discuss the findings in comparison with nanoindentation-induced cracking in other inorganic solid electrolyte materials and provide possible explanations for high resistance of Lipon to Li filament propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An investigation of fracture behaviors of NBG-18 nuclear graphite using in situ mechanical testing coupled with micro-CT

Nuclear graphite contains defects spanning from nanoscale basal cracks to sub-mm scale voids. This study aims to establish an experimental method to investigate pre-existing defects and 3-D crack growth inside nuclear graphite, NBG-18. Three-point bending tests were performed on single-edge notched beam specimens with and without coupling with micro-CT. The fracture toughness was measured to be 1.17 ± 0.06 MPa $\sqrt{{m}}$. Cracks were observed to initiate from the pores and thermal cracks on the edge of the notch and then defect or twist to grow along the pre-existing defects. Crack bridging, defection, and twisting were the primary toughening mechanisms. The crack resistance curve exhibited a trend of rising-plateau-rising that can be related to the interaction of crack front and the pre-existing defects. In conclusion, the results highlight the capability of laboratory micro-CT-based experimental method for the visualization of multi-scale defect interactions, which remains to be a challenge in the characterization of nuclear graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the optimized 3D printing and post-processing of PETG materials

Glycol-modified polyethylene terephthalate (PETG) is a reliable middle ground between polylactic acid and acrylonitrile butadiene styrene due to its light weight, impact resistance, toughness, flexibility, and cost-effectiveness. However, during 3D printing, the filament form is prone to oozing and stringing. In this study, we optimized the PETG printability via g-code setting and printing parameter modification, and consideration of filament quality, build plate temperature and leveling, and printing design complexity. Printed PETGs were thermally and chemically annealed, and post-processing conditions including annealing time, temperature, and solvent use were investigated. Mechanical properties were evaluated in terms of print parameter changes and post-processing techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Illinois State Geological Survey (ISGS), Illinois Basin - Decatur Project (IBDP) Geological Models, July 7, 2021. Midwest Geological Sequestration Consortium (MGSC) Phase III Data Sets. DOE Cooperative Agreement No. DE-FC26-05NT42588.

Three geological models in Petrel (Mark of Schlumberger) and data output from shallow groundwater modeling using TOUGH Codes from Lawrence Berkeley National Laboratory, included under folders: Static_Geologic_Model, Dynamic_Reservoir_Model, Geomechanical_Model, and Groundwater_Model.

3D Geological Model↗
DOE OSTI2020

A Bezier Curve Informed Melt Pool Geometry to Model Additive Manufacturing Microstructures Using SPPARKS

Additive manufacturing is a transformative technology with the potential to manufacture designs which traditional subtractive machining methods cannot. Additive manufacturing offers fast builds at near final desired geometry; however, material properties and variability from part to part remain a challenge for certification and qualification of metallic components. AM induced metallic microstructures are spatially heterogeneous and highly process dependent. Engineering properties such as strength and toughness are significantly affected by microstructure morphologies resulting from the manufacturing process Linking process parameters to microstructures and ultimately to the dynamic response of AM materials is critical to certifying and qualifying AM built parts and components and improving the performance of AM materials. The AM fabrication process is characterized by building parts layer by layer using a selective laser melt process guided by a computer. A laser selectively scans and melts metal according to a designated geometry. As the laser scans, metal melts, fuses, and solidifies forming the final geometry in a layerwise fashion. As the laser heat source moves away, the metal cools and solidifies forming metallic microstructures. This work describes a microstructure modeling application implemented in the SPPARKS kinetic Monte Carlo computational framework for simulating the resulting microstructures. The application uses Bzier curves and surfaces to model the melt pool surface and spatial temperature profile induced by moving the laser heat source; it simulates the melting and fusing of metal at the laser hot spot and microstructure formation and evolution when the laser moves away. The geometry of the melt pool is quite flexible and we explore effects of variances in model parameters on simulated microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Analytical Model of Erosive Wear of BioMass Comminution Components

An analytical erosion model that relates critical process parameters (speed and impingement angle) to critical material attributes of inorganic mineral species in feedstock (density, size, aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear in pretreatment milling operations. Results of the model were compared to experimental measurements of wear produced using the Accelerated Wear Test (AWT) rig at Idaho National Laboratory (INL). Results showed that there is good agreement between predicted and measured performance, and that a quality-by-design (QbD) tool can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

09 BIOMASS FUELS↗