SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report, prepared at the request of the NACA, describes tests of three metal model propellers, in a free air stream and in front of a model of a VE-7 airplane. The effect of introducing the model airplane is shown to be an increase in thrust and power coefficients and efficiency at small slip, and a decrease in the same at large slip.
The various speeds of an airplane can only be measured in horizontal flight, since there are no means for measuring the angle of ascent or descent. The measurements must be corrected for the density of the air. This is obtained by simultaneous pressure and temperature measurements during flight. Calculation from the mean yearly values in accordance with Everling's suggestion can only be considered an approximation, since the distribution of pressure and temperature in the individual strata at different altitudes undergoes such large variations that the yearly mean gives inaccurate values. Thermographs of the present form are useless for temperature measurements of an airplane. In altitude data, the following are to be distinguished: the height above the earth, the barometric altitude, and the altitude corresponding to the yearly mean air density. Variometers are not suited for the mechanical control of high altitude flight.
Simple flight tests were made on ten conventional airplanes for the purpose of determining their action in the following two situations, which are generally thought to precede and lead to a large proportion of airplane crashes.
Air flow about the fuselage and empennage during a high-angle-of-attack spin was made visible in flight by means of titanium-tetrachloride smoke and was photographed with a motion-picture camera. The angular relation of the direction of the smoke streamer to the airplane axes was computed and compared with the angular direction of the motion in space derived from instrument measurement of the spin of the airplane for a nearly identical mass distribution. The results showed that the fin and upper part of the rudder were almost completely surrounded by dead air, which would render them inoperative; that the flow around the lower portion of the rudder and the fuselage was nonturbulent; and that air flowing past the cockpit in a high-angle-of-attack spin could not subsequently flow around control surfaces.
The aerodynamic forces and moments on a 1/12-scale model of the F4B-2 airplane were measured with the spinning balance in nine spinning attitudes with three sets of tail surfaces, namely, F4B-2 surfaces; F4B-4 fin and rudder with rectangular stabilizer; and with all tail surfaces removed. In one of these attitudes measurements were made to determine the effect upon the forces and moments of independent and of simultaneous displacement of the rudder and elevator for two of the sets of tail surfaces. Additional measurements were made for a comparison of model and full-scale data for six attitudes that were determined from flight tests with various control settings. The characteristics were found to vary in the usual manner with angle of attack and sideslip. The F4B-2 surfaces were quite ineffective as a source of yawing moments. The F4B-4 fin and F4B-2 stabilizer gave a greater damping yawing moment when controls were against the spin than did the F4B-2 surfaces but otherwise there was little difference. Substitution of a rectangular stabilizer for the F4B-2 stabilizer made no appreciable difference in the coefficient. Further comparisons with other airplane types are necessary before final conclusions can be drawn as to the relations between model and full-scale spin measurements.
The proper landing of airplanes equipped with flaps, although probably no more difficult than landing without them, requires a different technique. The effects of flaps on the aerodynamics characteristics of a wing are given and, with the aid of figures and diagrams, a detailed comparison of the glide and landing of an airplane with and without flaps is made. The dangers attending improper execution and the importance of such factors as air speed fuselage attitude, glide-path angle, and control manipulation, upon all of which a pilot bases his judgement, are emphasized. Of most importance in connection with the use of flaps are: the maintenance of a sufficient margin of speed above the stall; a decisive use of the controls at the proper time; more cautious use of power during the approach glide; and, above all, the willingness to accept the steep nose-down attitude necessary in the glide resulting from the use of flaps.
The various possible means of preventing ice adhesion on airplane surfaces are critically reviewed. Results are presented of tests of the adhesives forces between ice and various solid and liquid forces. It is concluded that the de-icing of airplane wings by heat from engine exhaust shows sufficient promise to warrant full-scale tests. For propellers, at least, and possibly for certain small areas such as windshields, radio masts, etc. the use of de-icing or adhesion-preventing liquids will provide the best means of protection.
An investigation of three methods for the prevention and the removal of ice on an airplane windshield has been completed. The methods were: electric heating; hot-air heating; and an alcohol-dispensing, rotating wiper blade. The results showed that vision through the airplane windshield could be maintained during severe icing conditions by the use of heat. When put in operation prior to the formation of ice on the windshield the rotating wiper blade prevented the formation of ice. A combination of heated air and a rotating wiper blade would appear to protect against formation of ice on the windshield exterior, to prevent frost on the interior and to provide for the removal of rainfall.
Formulas are presented for the calculation of the additional mass corrections to the moments of inertia of airplanes. These formulas are of particular value in converting the virtual moments of inertia of airplanes or models experimentally determined in air to the true moments of inertia. A correlation of additional moments of inertia calculated by these formulas with experimental additional moments of inertia obtained from vacuum chamber tests of 40 spin-tunnel models indicates that formulas give satisfactory estimations of the additional moments of inertia.
Procedure for pilot escape from spinning airplanes has been determined by means of tests in which pilot escape was simulated from 21 airplane models spinning in the Langley 20-foot free-spinning tunnel. The results in general indicated that the pilot should bail out of the outboard side. Calculated centripetal accelerations acting on the pilot during a spin are presented.
The present report will treat only the smallest airplanes equipped with engines. The two types discussed are those airplanes with the smallest dimensions, and those that have the smallest power requirements.
Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.
Some results on the effects of wing flexibility on wing bending strains as determined from flight tests of a Boeing B-29 and a Boeing B-47A airplane in rough air are presented. Results from an analytical study of the flexibility effects on the B-29 wing strains are compared with the experimental results. Both the experimental and calculated results are presented as frequency-response functions of the bending strains at various spanwise wing stations to gust disturbances. In addition, some indirect evidence of the effect of spanwise variations in turbulence on the response of the B-47A airplane is presented.
Results of an investigation at low speeds to determine the gust-alleviation capabilities (reduction in lift-curve slope) of spoilers and deflectors on a 35 degree swept-wing model of high aspect ratio and on a 1/4-scale model of the X-5 airplane with 35 degree swept wings indicate that deflector and spoiler-deflector types of controls can be designed to provide considerable gust alleviation for a swept-wing airplane while still maintaining stability and control.
An analysis has been made of Civil Aeronautics Administration and Civil Aeronautics Board commercial airplane fire records collected during the 10-year period ending July 1, 1948. The results of the analysis show that: 1. Gasoline was most frequently the initial combustible ignited in flight and ground fires and is considered to be the most hazardous of the combustibles carried. 2. Although electrical-ignition sources are the most frequent flight-fire ignition source by a small margin, the exhaust system is concluded to be the most hazardous ignition source because it is necessarily located near the lubricating-oil and gasoline-plumbing systems and the resulting fires are relatively severe. The electrical-ignition sources usually involve only the electrical insulation and result in small-volume fires. The exhaust system was found to be the most frequent ground-fire ignition source. 3. Engine failures were the most frequent cause of the union of combustible and ignition source that resulted in flight fires. 4. Fuel-plumbing-system failures were the most frequent cause of fires occurring during ground operation. 5. The evidence concerning crash fires was not sufficiently extensive to provide information concerning the factors that affect the start and the spread of fire. In order that future records may be more useful, all crash accidents should be studied to determine why fire does or does not occur and to establish data that relate the occurrence and the spread of fire to airplane design and operation.
The improvement of airplanes and increased safety of air traffic can be sought in various ways. In the experiments described below, the aim was to find some simple and inexpensive method of modifying present-day airplanes, so as to improve and simplify the process of landing.
This report begins with a review and analysis of the work being done to develop light airplanes in the U.S. and abroad. A technical discussion of the construction and innovations in light airplanes is then presented.
During the flight program on the Bell X-5 airplane with 59 deg sweepback to determine the practical Mach number and normal-force coefficient limits of this configuration, a reduction in static longitudinal stability was encountered in maneuvering flight. A determination of the boundary for reduction of longitudinal stability extending to a Mach number of 0.98 is presented in this paper. A reduction of static longitudinal stability existed for all elevator and all stabilizer-executed maneuvers. The reduction of stability existed for maneuvers executed with elevator near a normal-force coefficient of 0.6 for a Mach number range of about 0.31 to 0.76. Above a Mach number of 0.76 the normal-force coefficient for reduction of stability gradually decreased to a value of 0.2 at a Mach number of 0.98. For stabilizer-executed maneuvers the stability boundary was the same as for elevator maneuvers up to a Mach number of 0.88. Above this Mach number the reduction of stability occurred at slightly higher normal-force coefficients decreasing from about 0.51 at a Mach number of 0.92 to a value of 0.311 at a Mach number of 0.97. The airplane has been flown to a Mach number of 1.04 at a normal-force coefficient of about 0.15 without encountering any reduction of stability. The pilot did not consider the reduction of stability to be dangerous at altitudes above 30,000 feet; however, precise flight was impossible. At angles of attack above that at which the reduction of longitudinal stability occurred, directional instability and aileron control overbalance were encountered.