SEARCH · Search NASA

Results for “COMBUSTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Performance of a vortex-controlled diffuser in an annular swirl-can combustor at inlet Mach numbers up to 0.53

A short, annular dump diffuser with suction stabilized vortices in the region of abrupt area change was tested with a full scale, annular swirl can combustor. The prediffuser area ratio was 1.4. Performance data were obtained for both isothermal and burning conditions at inlet temperatures of 589 to 895 K and pressures of 0.5 to 1.0 MPa for a range of diffuser inlet Mach numbers from 0.25 to 0.53. Suction rates were 0 to 20 percent of the total diffuser mass flow rate. Diffuser effectiveness increased from 47 percent without suction to approximately 80 percent for a total suction rate of 14 percent. Combustor total pressure loss for the same total suction rate was reduced from 6.8 percent without suction to 4.0 percent at an inlet Mach number of 0.40.

Smith, J. M.↗

NASA NTRS1979

Effect of degree of fuel vaporization on emissions for a premixed-prevaporized combustor system

The impact of the degree of fuel vaporization upon emission from a flametube combustor was studied using an inlet air pressure of 3 x 10 to the 5th power pascals, inlet air temperatures of 600K and 700K, a reference velocity of 35 meters per second and equivalence ratios of .6 and .72 using Jet A fuel. Incoming air was preheated to temperatures from 600K to 700K by a nonvitiating preheater. Jet A fuel was injected into this airstream through two different fuel injectors manifolded together and mounted in series upstream of a watercooled preforated plate flameholder. The fuel-air mixture burned in a watercooled combustor section. Samples of the fuel-air mixture upstream of the flameholder were obtained for analysis to determine the local degree of fuel vaporization and the fuel-air ratio. Samples of the combustion products were analyzed to determine gaseous emissions. The effects of vaporization on carbon monoxide and nitric on carbon monoxide and nitric oxide emissions are presented.

Cooper, L. P.↗

NASA NTRS1979

Stabilization of premixed combustors

In order to attain a sufficiently good insight into the fluid mechanical processes taking place in combustors operating on premixed, prevaporized, and preheated gases, an experimental facility was developed where the flow field is tractable both experimentally and analytically. The configuration adopted for the initial stage of the study is based on the use of a step to stabilized the combustion zone. The primary purpose of the experimental apparatus is to provide a facility for studying the effects of the elementary fluid mechanical processes on the stability of a model combustion system in order to further the understanding of the intrinsic mechanism of nonsteady phenomena, rather than to provide criteria for unstable operation of combustors, as expressed by overall performance parameters, such as the blowout and flashback limits.

Sawyer, R. F.↗

NASA NTRS1979

Lean, premixed, prevaporized fuel combustor conceptual design study

Four combustor concepts, designed for the energy efficient engine, utilize variable geometry or other flow modulation techniques to control the equivalence ratio of the initial burning zone. Lean conditions are maintained at high power to control oxides of nitrogen while near stoichometric conditions are maintained at low power for low CO and THC emissions. Each concept was analyzed and ranked for its potential in meeting the goals of the program. Although the primary goal of the program is a low level of nitric oxide emissions at stratospheric cruise conditions, both the ground level EPA emission standards and combustor performance and operational requirements typical of advanced subsonic aircraft engines are retained as goals as well. Based on the analytical projections made, two of the concepts offer the potential of achieving the emission goals; however, the projected operational characteristics and reliability of any concept to perform satisfactorily over an entire aircraft flight envelope would require extensive experimental substantiation before engine adaptation can be considered.

Fiorentino, A. J.↗

NASA NTRS1979

Emission characteristics of a premix combustor fueled with a simulated partial-oxidation product gas

A two-stage gas turbine combustor concept employing a very fuel-rich partial oxidation stage is being explored for broadening the combustion margin between ultralow emissions and the lean stability limit. Combustion and emission results are presented for a series of experiments where a simulated partial oxidation product gas was used in a premix combustor operated with inlet air state conditions typical of cruise power for high-performance aviation engines (12 atm and 850 F). Ultralow NOx, CO, and HC emissions and an extended lean burning limit were achieved simultaneously.

Clayton, R. M.↗

NASA NTRS1979

Combustor modelling for scramjet engines

A system of computer programs is being developed to analyse and predict the complex flow fields found in hydrogen-fueled scramjet combustors. Each program is designed to solve the governing equation system for the type of flow present in a particular combustor region. A two-dimensional parabolic program has been found to be valuable in the development and experimental evaluation of turbulence and chemistry models for supersonic flow, and in the development of a program to model supersonic flow downstream of the fuel injection struts by means of solutions to the three-dimensional parabolic Navier-Stokes equations and species equations. A partially elliptic code has been derived to account for local subsonic flow regions, and fully elliptic programs have been developed by the consideration of streamwise diffusion effects for the recirculating flow fields near transverse fuel injectors. The programs are currently being applied to problems of scramjet engine development.

Drummond, J. P.↗

NASA NTRS1980

Reduction of nitric oxide emissions from a combustor

A turbojet combustor and method for controlling nitric oxide emissions by employing successive combustion zones is described. After combustion of an initial portion of the fuel in a primary combustion zone, the combustion products of the primary zone are combined with the remaining portion of fuel and additional plenum air and burned in a secondary combustion zone under conditions that result in low nitric oxide emissions. Low nitric oxide emissions are achieved by a novel turbojet combustor arrangement which provides flame stability by allowing stable combustion to be accompanied by low nitric oxide emissions resulting from controlled fuel-lean combustion (ignited by the emission products from the primary zone) in a secondary combustion zone at a lower combustion temperature resulting in low emission of nitric oxide.

Craig, R. A.↗

NASA NTRS1980

Preliminary studies of combustor sensitivity to alternative fuels

Combustion problems associated with using alternative fuels ground power and aeropropulsion applications were studied. Rectangular sections designed to simulate large annular combustor test conditions were examined. The effects of using alternative fuels with reduced hydrogen content, increased aromatic content, and a broad variation in fuel property characteristics were also studied. Data of special interest were collected which include: flame radiation characteristics in the various combustor zones; the correponding increase in liner temperature from increased radiant heat flux; the effect of fuel bound nitrogen on oxides of nitrogen (NO sub x) emissions; and the overall total effect of fuel variations on exhaust emissions.

Humenik, F. M.↗

NASA NTRS1980

Conceptual model of turbulent flameholding for scramjet combustors

New concepts and approaches to scramjet combustor design are presented. Blowoff was from failure of the recirculation-zone (RZ) flame to reach the dividing streamline (DS) at the rear stagnation zone. Increased turbulent exchange across the DS helped flameholding due to forward movement of the flame anchor point inside the RZ. Modeling of the blowoff phenomenon was based on a mass conservation concept involving the traverse of a flame element across the RZ and a flow element along the DS. The scale required to achieve flameholding, predicted by the model, showed a strong adverse effect of low pressure and low fuel equivalence ratio, moderate effect of flight Mach number, and little effect of temperature recovery factor. Possible effects of finite rate chemistry on flameholding and flamespreading in scramjets are discussed and recommendations for approaches to engine combustor design as well as for needed research to reduce uncertainties in the concepts are made.

Huber, P. W.↗

NASA NTRS1979

The erosion/corrosion of small superalloy turbine rotors operating in the effluent of a PFB coal combustor

The operation of a turbine in the effluent of a pressurized fluidized bed (PFB) coal combustor presents serious materials problems. Synergistic erosion/corrosion and deposition/corrosion interactions may favor the growth of erosion-resistant oxides on blade surfaces, but brittle cracking of these oxides may be an important source of damage along heavy particle paths. Integrally cast alloy 713LC and IN792 + Hf superalloy turbine rotors in a single-stage turbine with 6% partial admittance have been operated in the effluent of a PFB coal combustor for up to 164 hr. The rotor erosion pattern exhibits heavy particle separation with severe erosion at the leading edge, pressure side center, and suction side trailing edge at the tip. The erosion distribution pattern gives a spectrum of erosion/oxidation/deposition as a function of blade position. The data suggest that preferential degradation paths may exist even under the targeted lower loadings (less than 20 ppm).

Zellars, G. R.↗

NASA NTRS1979

Driving of combustor oscillations by gaseous propellant injectors

Measurements of reactive admittances that describe the capabilities of the combustion processes associated with coaxial gaseous fuel injectors to amplify combustor oscillations are presented. These admittances are needed in (1) stability analyses of rocket motors and gas turbine combustors; (2) for the evaluation of 'driving' capabilities of injectors; and (3) for checking the applicability of a theoretical model. The modified standing-wave technique was used to determine the admittances of the combustion processes in coaxial injectors utilizing air-acetylene mixtures. The measurements indicated that (1) coaxial injectors can sustain combustion instabilities over wide frequency ranges; (2) the maximum driving capability of an injector decreases with an increased equivalence ratio; (3) the frequency at which maximum driving is observed decreases with the increased equivalence ratio; and (4) the characteristic combustion time of an injector design decreases with increased frequency.

Janardan, B. A.↗

NASA NTRS1979

Measurement of vortex frequencies in a lean, premixed prevaporized combustor

A modified laser schlieren and fast Fourier transform analysis system has been developed and applied to the study of vortex frequencies in a lean, premixed prevaporized combustor. The system is sensitive to the passage of vortex structures which dominate the flow in the combustor studied. The frequency spectra of the passage of vortices show distinct frequency peaks which are postulated to be characteristic of the processes triggering the vortex shedding. The method provides additional information which should aid in the characterization and understanding of shear flows.

Parker, L. J.↗

NASA NTRS1980

Catalytic honeycomb combustor - Steady-state model and comparison with experiment

A steady-state lean combustion model for monolithic catalytic combustors is given. The model, consisting of several semi-global chemical reaction steps in the gas-phase and on the surface, is capable of analyzing CO and THC emissions. In the model computation presented, the influence of operating and design parameters on the minimum combustor length is studied. Special attention is given to the effect of after-bed gas-phase reaction space. Comparison with experimental data indicates good agreement in the range of parameters covered.

Tien, J. S.↗

NASA NTRS1980

Atomizing characteristics of swirl can combustor modules with swirl blast fuel injectors

Cold flow atomization tests of several different designs of swirl can combustor modules were conducted in a 7.6 cm diameter duct at airflow rates (per unit area) of 7.3 to 25.7 g/sq cm sec and water flow rates of 6.3 to 18.9 g/sec. The effect of air and water flow rates on the mean drop size of water sprays produced with the swirl blast fuel injectors were determined. Also, from these data it was possible to determine the effect of design modifications on the atomizing performance of various fuel injector and air swirler configurations. The trend in atomizing performance, as based on the mean drop size, was then compared with the trends in the production of nitrogen oxides obtained in combustion studies with the same swirl can combustors.

Ingebo, R. D.↗

NASA NTRS1982

Two-Stage Combustor Reduces Pollutant Emissions

By controlling fuel-to-air ratio of local reactants, pollutant emissions would be minimized in a proposed two-stage combustor for gas-turbine engines. It would use fuel-rich partial-oxidation stage and air-rich combustion stage to reduce emissions of nitrogen oxide, carbon monoxide and hydrocarbons. Combustor fuel-lean burning limit would be extended simultaneously.

Clayton, R. M.↗

NASA NTRS1980

Effect of ambient conditions on the emissions from a gas turbine combustor

The effect of variations in the ambient conditions of pressure, temperature, and relative humidity upon the emissions of a gas turbine combustion are investigated. A single combustor can from a Pratt and Whitney JT8D-17 engine was run at parametric inlet conditions bracketing the actual engine idle conditions. Data were correlated to determine the functional relationships between the emissions and ambient conditions. Mathematical modelling was used to determine the mechanism for the carbon monoxide and hydrocarbon emissions. Carbon monoxide emissions were modelled using finite rate chemical kinetics in a plug flow scheme. Hydrocarbon emissions were modelled by a vaporization scheme throughout the combustor.

Kauffman, C. W.↗

NASA NTRS1980

Evaluation of a bulk calorimeter and heat balance for determination of supersonic combustor efficiency

Results are presented from the shakedown and evaluation test of a bulk calorimeter. The calorimeter is designed to quench the combustion at the exit of a direct-connect, hydrogen fueled, scramjet combustor model, and to provide the measurements necessary to perform an analysis of combustion efficiency. Results indicate that the calorimeter quenches reaction, that reasonable response times are obtained, and that the calculated combustion efficiency is repeatable within + or -3 percent and varies in a regular way with combustor model parameters such as injected fuel equivalence ratio.

Mcclinton, C. R.↗

NASA NTRS1981

Combustor liner durability analysis

An 18 month combustor liner durability analysis program was conducted to evaluate the use of advanced three dimensional transient heat transfer and nonlinear stress-strain analyses for modeling the cyclic thermomechanical response of a simulated combustor liner specimen. Cyclic life prediction technology for creep/fatigue interaction is evaluated for a variety of state-of-the-art tools for crack initiation and propagation. The sensitivity of the initiation models to a change in the operating conditions is also assessed.

Moreno, V.↗