Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Optimum Design of Insulated Compression Plates Subjected to Aerodynamic Heating

A method to determine the optimum thicknesses of insulation and load-carrying structure has been applied to insulated compression plates subjected to aerodynamic heating. The optimum design results in the lowest combined weight of insulation and load-carrying plate. Load parameters which included the imposed load, insulation conductivity and density, and flight time were found for design strength criteria of compressive yield, compressive buckling, and postbuckling failure. Charts of optimum total weight were prepared for 2024-T3 aluminum alloy, HK3lA magnesium alloy, 17-7 PH stainless steel, and Inconel X for each design criterion. The results show that 17-7 PH stainless steel and Inconel X are most efficient for compressive yield stress and that HK3lA magnesium is most efficient for buckling. HK31A magnesium is also most efficient for the postbuckling failure criterion except under conditions of light loading and long flight periods; under such conditions uninsulated Inconel X may be superior for environmental temperature less than 1,200 F. Insulated magnesium is more efficient than insulated aluminum because the lower density of magnesium permits the use of thick plates with large heat capacity. When more than one failure mode was applied to a design, it was found that the minimum weight structure was one in which all modes of failure occurred at the design load.

Davidson, John R.↗
NASA NTRS2007

Effects of Different R ratios on Fatigue Crack Growth in Laser Peened Friction Stir Welds

The influence of laser peening on the fatigue crack growth behavior of friction stir welded (FSW) Aluminum Alloy (AA) 7075-T7351 sheets was investigated. The surface modification resulting from the peening process on the fatigue crack growth of FSW was assessed for two different R ratios. The investigation indicated a significant decrease in fatigue crack growth rates resulting from using laser shock peening compared with unpeened, welded and unwelded specimens. The slower fatigue crack growth rate was attributed to the compressive residual stresses induced by the peening.

Hatamleh, Omar↗
NASA NTRS1992

Method for improved prediction of bone fracture risk using bone mineral density in structural analysis

A non-invasive in-vivo method of analyzing a bone for fracture risk includes obtaining data from the bone such as by computed tomography or projection imaging which data represents a measure of bone material characteristics such as bone mineral density. The distribution of the bone material characteristics is used to generate a finite element method (FEM) mesh from which load capability of the bone can be determined. In determining load capability, the bone is mathematically compressed, and stress, strain force, force/area versus bone material characteristics are determined.

Cann, Christopher E.↗
NASA NTRS2010

Burnishing Techniques Strengthen Hip Implants

In the late 1990s, Lambda Research Inc., of Cincinnati, Ohio, received Small Business Innovation Research (SBIR) awards from Glenn Research Center to demonstrate low plasticity burnishing (LPB) on metal engine components. By producing a thermally stable deep layer of compressive residual stress, LPB significantly strengthened turbine alloys. After Lambda patented the process, the Federal Aviation Administration accepted LPB for repair and alteration of commercial aircraft components, the U.S. Department of Energy found LPB suitable for treating nuclear waste containers at Yucca Mountain. Data from the U.S. Food and Drug Administration confirmed LPB to completely eliminate the occurrence of fretting fatigue failures in modular hip implants.

Source record↗
NASA NTRS2012

Rolling Bearing Steels - A Technical and Historical Perspective

Starting about 1920 it becomes easier to track the growth of bearing materials technology. Until 1955, with few exceptions, comparatively little progress was made in this area. AISI 52100 and some carburizing grades (AISI 4320, AISI 9310) were adequate for most applications. The catalyst to quantum advances in high-performance rolling-element bearing steels was the advent of the aircraft gas turbine engine. With improved bearing manufacturing and steel processing together with advanced lubrication technology, the potential improvements in bearing life can be as much as 80 times that attainable in the late 1950s or as much as 400 times that attainable in 1940. This paper summarizes the chemical, metallurgical and physical aspects of bearing steels and their effect on rolling bearing life and reliability. The single most important variable that has significantly increased bearing life and reliability is vacuum processing of bearing steel. Differences between through hardened, case carburized and corrosion resistant steels are discussed. The interrelation of alloy elements and carbides and their effect on bearing life are presented. An equation relating bearing life, steel hardness and temperature is given. Life factors for various steels are suggested and discussed. A relation between compressive residual stress and bearing life is presented. The effects of retained austenite and grain size are discussed.

Zaretsky, Erwin V.↗
NASA NTRS2012

Simulation of Complex Cracking in Plain Weave C/SiC Composite under Biaxial Loading

Finite element analysis is performed on a mesh, based on computed geometry of a plain weave C/SiC composite with assumed internal stacking, to reveal the pattern of internal damage due to biaxial normal cyclic loading. The simulation encompasses intertow matrix cracking, matrix cracking inside the tows, and separation at the tow-intertow matrix and tow-tow interfaces. All these dissipative behaviors are represented by traction-separation cohesive laws. Not aimed at quantitatively predicting the overall stress-strain relation, the simulation, however, does not take the actual process of fiber debonding into account. The fiber tows are represented by a simple rule-of-mixture model where the reinforcing phase is a hypothetical one-dimensional material. Numerical results indicate that for the plain weave C/SiC composite, 1) matrix-crack initiation sites are primarily determined by large intertow matrix voids and interlayer tow-tow contacts, 2) the pattern of internal damage strongly depends on the loading path and initial stress, 3) compressive loading inflicts virtually no damage evolution. KEY WORDS: ceramic matrix composite, plain weave, cohesive model, brittle failure, smeared crack model, progressive damage, meso-mechanical analysis, finite element.

Cheng, Ron-Bin↗
DOE OSTI2023

Geomechanical Characterization of the Mount Simon Sandstone and Eau Claire Formation of Northern Illinois Basin

The purpose of this paper is to analyze publicly available geomechanical data from two carbon storage sites in the Illinois Basin: the Illinois Basin-Decatur Project (IBDP) in Macon County, IL and the FutureGen2.0 project in Morgan County, IL, cancelled before injection began. This study estimates the magnitudes and directions of the least compressive principal stress gradient using hydraulic fracture-based stress measurement tests, borehole breakouts, and sonic logs in the Eau Claire Formation (primary confining zone) and the Mount Simon Sandstone (targeted reservoir). The range of stresses expected in the underlying Precambrian basement is also investigated. The evaluation of the state of stress is carried out in a probabilistic manner using the State of Stress Analysis Tool (SOSAT) developed under the National Risk Assessment Partnership (NRAP) program. Finally, the paper also provides a discussion on distinctions between fracture initiation pressure, propagation pressure, and fracture closure pressure, given that hydraulic fracture testing results show a significant difference between these three values. The discussion also addresses why the fracture closure pressure should be preferred in injection pressure determinations, a critical point in geological carbon storage projects.

de Toledo Camargo, Julia↗
NASA NTRS1947

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-walled cylinders loaded in axial compression. These curves are plotted in terms of nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75. The test data obtained from various sources follow the general trend of the theoretical curve for cylinders with clamped edges, agreeing closely with the theory in the case of short cylinders, but falling considerably below the theoretical results for long cylinders. The discrepancy in the case of long cylinders increases with increasing values of the ratio of radius to wall thickness. Plotting curves for different values of this ratio reduces the scatter in the test data and a certain degree of correlation with theory is achieved. Advantage is taken of this correlation to obtain estimated design curves for cylinders with simply supported edges, for which little experimental information is available. (author)

Batdorf, S B↗
NASA NTRS1947

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

Batdorf, S B↗
NASA NTRS1980

Effect of thermal cycling on ZrO2-Y2O3 thermal barrier coatings

The paper studies the comparative life of plasma-sprayed ZrO2-Y2O3 thermal barrier coatings on NiCrAlY bond coats on Rene 41 in short (4 min) and long (57 min) thermal cycles at 1040 C in a 0.3-Mach flame. Attention is given to determining the effect of short- and long-duration cycles on ZrO2-Y2O3 coatings, the cause of any cycle frequency effects, and methods to improve tolerance to thermal stress. Short cycles greatly reduced the life of the ceramic coating in terms of time at temperatures as compared to longer cycles, the failed coating indicating compressive failure. The experiments and stress calculations show that repeatedly subjecting a ceramic coating to high rates of initial heating has a more destructive influence on the coating than sustained operation at temperature. The effect of such thermal compressive stresses might be minimized through coating deposition and thickness control and by turbine cycle measurement to keep starting heating rates below critical values.

Mcdonald, G.↗
NASA NTRS1990

A study of turbulence on compression ramps with k-epsilon and Reynolds stress models

A theoretical study was conducted to determine the effects of adverse pressure gradient and compressibility in modeling turbulent compressible flows. The kinetic energy/dissipation and Reynolds stress model predictions are presented and compared with experimental data. The effects of compressibility, which include the mass averaged fluctuation term, the pressure dilatation term, and the dilatation dissipation, are important in modeling the turbulent compressible flows. The normal stresses and longitudinal strain rates also have an effect in the prediction of turbulent energy productions on the curved surfaces. A new compressible formulation of the pressure strain term, which includes the dilatation effects, in the Reynolds stress equation is presented.

Lee, J.↗
NASA NTRS2005

Compression and Tensile Creep of Binary NiAl

Compression creep and long term tensile creep studies were conducted on cast and extruded binary NiAl in the temperature range 700-1200 K with the objectives of characterizing and understanding the creep mechanisms. Inverse and normal primary creep curves were observed in both compression and tension creep depending on stress and temperature although an asymmetrical response was observed under these two stress states. It was concluded that the primary creep of NiAl is limited by dislocation mobility. The stress exponents, n, for compression and tensile creep were similar varying between about 5 and 14. However, there were significant differences in the stress dependence of the activation energies for compression and tensile creep. The true activation energy for tensile creep, Q(sub c), was constant and equal to about 400 kJ/mol between 20 and 50 MPa but decreased to a constant value of 250 kJ/mol between 50 and 110 MPa. The activation energy was observed to be inversely stress dependent above 110 MPa. In contrast, Q(sub c) = 300 kJ/mol for compression creep was constant between 25 and 70 MPa and inversely dependent on the true stress above 70 MPa. A detailed discussion of the probable dislocation creep mechanisms governing compressive and tensile creep of NiAl is presented. It is concluded that the non-conservative motion of jogs on screw dislocations influenced the nature of the primary creep curves, where the climb of these jogs involves either the next nearest neighbor or the six-jump cycle vacancy diffusion mechanism. The probable natures of the atom-vacancy exchange that occur within the core of an edge dislocation undergoing climb in NiAl are schematically examined.

Raj, Sai V.↗
DOE OSTI2025

Crystallographic Texture, Structure, and Stress Transmission in Nugget Sandstone Examined With X‐Ray Tomography and Diffraction Microscopy

Subsurface processes in sandstones are controlled by porosity, permeability, and deformation mechanisms, all of which are controlled by a complex interplay of crystallographic rock texture, structure, and micromechanics. Texture, structure, and micromechanics have historically been studied using optical and electron microscopy of thin-sections. Here, we employed a new combination of in situ X-ray tomography and ray diffraction microscopy to study crystallographic texture, structure, and grain stresses in 3D. We examined these features in a sample of Nugget sandstone, a sandstone constituting hydrocarbon reservoirs across the American West. Our aims are threefold. First, we demonstrate the utility of X-ray diffraction microscopy probes for revealing texture, structure, and stress transmission in 3D. Second, we apply these techniques to Nugget sandstone and discuss findings in the context of prior work. Third, we study grain stress tensor evolution during mechanical compression to examine whether their heterogeneity and orientation evolution reflect that of inter-particle forces in granular materials. Our results show: (a) larger grains featured higher intra-granular misorientations, possibly from an increased prevalence of cements; (b) pores closed parallel to the loading direction and opened normal to loading; (c) grain stresses featured heterogeneity and orientations similar to inter-particle forces in non-cohesive granular materials; (d) grains featured compressive stresses in the loading direction and tensile stresses orthogonal to the loading direction, the latter resisting sample dilation and grain separation. Our work demonstrates the first known application of multi-modal X-ray tomography and diffraction microscopy to sandstone, providing new 3D insight into the nature of quartz cement and stress evolution.

high energy diffraction microscopy↗
NASA NTRS1990

Simulation of crack growth and crack closure under large cyclic plasticity

The propagation of a crack during cyclic loading with large plasticity was simulated using a finite element method. The numerical procedure included the determination of crack closing and opening by examining the contact condition of the crack surfaces in the plasticity iteration. The method was applied to the growth of cracks in Alloy 718 single edge notch specimens at 538 C subject to strain cycling under both nominally elastic and elastoplastic conditions. The results show, among other things, that the crack closure and opening stresses become more compressive as the loading becomes more plastic, and that, under a given control condition, the closure and opening stresses become less compressive as the crack propagates.

Kim, K. S.↗
DOE OSTI2021

Constraint and size effects in confined layer plasticity

Plane strain finite element analyses are used to model the experiments for a thin metal layer confined between elastic solids. Here, the thin metal layer undergoes elastic-plastic deformations, here modelled by strain gradient plasticity, while the rest of the solid deforms only elastically. Plane strain is assumed and finite strains are accounted for. The microscopic boundary condition at the band interface is initially taken to be zero plastic strain increment, but plastic straining at the interface is allowed when the plastic strain gradient at the interface has exceeded a critical value. When the narrow metal band is inclined 45° relative to the direction of compression of the solid simple shear develops in the band and predictions are rather similar to those of a one-dimensional analysis for an infinite band. For a band at 90° the elastic parts give significant constraint on plastic flow, the stress fields are non-uniform along the band and the average nominal compressive stress shows strong sensitivity to the layer thickness and to the width of the specimen. Remarkably good qualitative, and in some cases quantitative, agreement is found with the experimental observations. Considering also other band angles, both the average nominal shear and compressive stress show variations with the angle.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sound speed measurements in shock-compressed cemented Tungsten carbides at pressures up to 100 GPa

To gain insights into thermodynamic states attained during shock compression of cemented tungsten carbide with 3.7 wt.% cobalt binder, we present results of longitudinal sound (release wave) speed measurements and their analysis at peak stresses up to 100 GPa (volumetric compression ratio ~ 15%). The sound speeds are determined using front-surface impact and release-wave overtake plate impact experimental configurations using laser interferometry. The measured sound speed data along with estimates for bulk sound speeds obtained using the fourth-order Birch-Murnaghan EoS and thermodynamics are used to determine the longitudinal moduli and shear moduli of shocked tungsten carbide at the various peak compression states attained in the experiments. Here, the longitudinal sound speeds were found to increase linearly with volume compression ratio from 6.97 ± 0.010 km/s at ambient conditions to 8.26 ± 0.156 km/s at a volume compression ratio of ~ 15%. The corresponding longitudinal elastic moduli also increase nearly linearly with the volume compression ratio but remain consistently lower than their theoretical predictions based on continuum models with no damage. Also, the sensitivity of shear moduli to pressure, as predicted by the Steinberg-Guinan model, is reduced substantially and the shear moduli of cemented WC with 3.7 wt.% Co remains nearly constant at ~ 310 GPa at the various peak compression stress states investigated in the present study.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Investigation of high-speed free shear flows using improved pressure-strain correlated Reynolds stress turbulence model

A high-speed shear layer is studied using compressibility corrected Reynolds stress turbulence model which employs newly developed model for pressure-strain correlation. MacCormack explicit prediction-corrector method is used for solving the governing equations and the turbulence transport equations. The stiffness arising due to source terms in the turbulence equations is handled by a semi-implicit numerical technique. Results obtained using the new model show a sharper reduction in growth rate with increasing convective Mach number. Some improvements were also noted in the prediction of the normalized streamwise stress and Reynolds shear stress. The computed results are in good agreement with the experimental data.

Tiwari, S. N.↗
DOE OSTI2020

Tuning crack-inclusion interaction with an applied T -stress

The interaction between cracks and inclusions plays an important role in the fracture behavior of particulate composites. It is commonly recognized that an inclusion stiffer than the matrix tends to deflect an approaching crack away while a softer inclusion attracts the crack. Here, we demonstrate by analytical modeling and numerical simulations that the crack-inclusion interaction can be tuned by an applied T-stress. Under a sufficiently large compressive applied T-stress, cracks can be attracted to stiffer inclusions while repelled by softer ones, therefore reversing the conventional trend. Potential applications of this work include composite electrodes in lithium-ion batteries and hydraulic fracturing.

36 MATERIALS SCIENCE↗