Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer Based Procedures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Ten-year ground exposure of composite materials used on the Bell Model 206L helicopter flight service program

Residual strength results are presented for four composite material systems that have been exposed for up to 10 years to the environment at five different locations on the North American continent. The exposure locations are near where the Bell Model 206L helicopters, which participated in a flight service program sponsored by NASA Langley Research Center and the U.S. Army, were flying in daily commercial service. The composite material systems are (1) Kevlar-49 fabric/F-185 epoxy; (2) Kevlar-49 fabric/LRF-277 epoxy; (3) Kevlar-49 fabric/CE-306 epoxy; and (4) T-300 graphite/E-788 epoxy. Six replicates of each material were removed and tested after 1, 3, 5, 7, and 10 years of exposure. The average baseline strength was determined from testing six as-fabricated specimens. More than 1700 specimens have been tested. All specimens that were tested to determine their strength were painted with a polyurethane paint. Each set of specimens also included an unpainted panel for observing the weathering effects on the composite materials. A statistically based procedure has been used to determine the strength value above which at least 90 percent of the population is expected to fall with a 95-percent confidence level. The computed compression strengths are 80 to 90 percent of the baseline (no-exposure) strengths. The resulting compression strengths are approximately 8 percent below the population mean strengths. The computed short-beam-shear strengths are 83 to 92 percent of the baseline (no-exposure) strengths. The computed tension strength of all materials is 93 to 97 percent of the baseline (no-exposure) strengths.

Baker, Donald J.↗
NASA NTRS1995

A software tool to design thermal barrier coatings

This paper summarizes work completed for a NASA Phase 1 SBIR program which demonstrated the feasibility of developing a software tool to aid in the design of thermal barrier coating (TBC) systems. Toward this goal, three tasks were undertaken and completed. Task 1 involved the development of a database containing the pertinent thermal and mechanical property data for the top coat, bond coat and substrate materials that comprise a TBC system. Task 2 involved the development of an automated set-up program for generating two dimensional (2D) finite element models of TBC systems. Most importantly, Task 3 involved the generation of a rule base to aid in the design of a TBC system. These rules were based on a factorial design of experiments involving FEM results, and were generated using a Yates analysis. A previous study has indicated the suitability and benefit of applying finite element analysis to perform computer based experiments to decrease but not eliminate physical experiments on TBC's. This program proved feasibility by expanding on these findings by developing a larger knowledge base and developing a procedure to extract rules to aid in TBC design.

Petrus, G.↗
NASA NTRS1995

A software tool to design thermal barrier coatings

This paper summarizes work completed for a NASA Phase 1 SBIR program which demonstrated the feasibility of developing a software tool to aid in the design of thermal barrier coating (TBC) systems. Toward this goal, three tasks were undertaken and completed. Task 1 involved the development of a database containing the pertinent thermal and mechanical property data for the top coat, bond coat and substrate materials that comprise a TBC system. Task 2 involved the development of an automated set-up program for generating two dimensional (2D) finite element models of TBC systems. Most importantly, task 3 involved the generation of a rule base to aid in the design of a TBC system. These rules were based on a factorial design of experiments involving FEM results and were generated using a Yates analysis. A previous study had indicated the suitability and benefit of applying finite element analysis to perform computer based experiments to decrease but not eliminate physical experiments on TBC's. This program proved feasibility by expanding on these findings by developing a larger knowledgebase and developing a procedure to extract rules to aid in TBC design.

Petrus, Gregory↗
NASA NTRS1999

Physics Based Modeling and Rendering of Vegetation in the Thermal Infrared

We outline a procedure for rendering physically-based thermal infrared images of simple vegetation scenes. Our approach incorporates the biophysical processes that affect the temperature distribution of the elements within a scene. Computer graphics plays a key role in two respects. First, in computing the distribution of scene shaded and sunlit facets and, second, in the final image rendering once the temperatures of all the elements in the scene have been computed. We illustrate our approach for a simple corn scene where the three-dimensional geometry is constructed based on measured morphological attributes of the row crop. Statistical methods are used to construct a representation of the scene in agreement with the measured characteristics. Our results are quite good. The rendered images exhibit realistic behavior in directional properties as a function of view and sun angle. The root-mean-square error in measured versus predicted brightness temperatures for the scene was 2.1 deg C.

Smith, J. A.↗
NASA NTRS2006

Closed-Loop Evaluation of an Integrated Failure Identification and Fault Tolerant Control System for a Transport Aircraft

Formal robustness analysis of aircraft control upset prevention and recovery systems could play an important role in their validation and ultimate certification. Such systems developed for failure detection, identification, and reconfiguration, as well as upset recovery, need to be evaluated over broad regions of the flight envelope or under extreme flight conditions, and should include various sources of uncertainty. To apply formal robustness analysis, formulation of linear fractional transformation (LFT) models of complex parameter-dependent systems is required, which represent system uncertainty due to parameter uncertainty and actuator faults. This paper describes a detailed LFT model formulation procedure from the nonlinear model of a transport aircraft by using a preliminary LFT modeling software tool developed at the NASA Langley Research Center, which utilizes a matrix-based computational approach. The closed-loop system is evaluated over the entire flight envelope based on the generated LFT model which can cover nonlinear dynamics. The robustness analysis results of the closed-loop fault tolerant control system of a transport aircraft are presented. A reliable flight envelope (safe flight regime) is also calculated from the robust performance analysis results, over which the closed-loop system can achieve the desired performance of command tracking and failure detection.

Shin, Jong-Yeob↗
NASA NTRS2004

Mid-frequency Band Dynamics of Large Space Structures

High and low intensity dynamic environments experienced by a spacecraft during launch and on-orbit operations, respectively, induce structural loads and motions, which are difficult to reliably predict. Structural dynamics in low- and mid-frequency bands are sensitive to component interface uncertainty and non-linearity as evidenced in laboratory testing and flight operations. Analytical tools for prediction of linear system response are not necessarily adequate for reliable prediction of mid-frequency band dynamics and analysis of measured laboratory and flight data. A new MATLAB toolbox, designed to address the key challenges of mid-frequency band dynamics, is introduced in this paper. Finite-element models of major subassemblies are defined following rational frequency-wavelength guidelines. For computational efficiency, these subassemblies are described as linear, component mode models. The complete structural system model is composed of component mode subassemblies and linear or non-linear joint descriptions. Computation and display of structural dynamic responses are accomplished employing well-established, stable numerical methods, modern signal processing procedures and descriptive graphical tools. Parametric sensitivity and Monte-Carlo based system identification tools are used to reconcile models with experimental data and investigate the effects of uncertainties. Models and dynamic responses are exported for employment in applications, such as detailed structural integrity and mechanical-optical-control performance analyses.

dynamics↗
NASA NTRS2013

High-Order Methods for Computational Fluid Dynamics: A Brief Review of Compact Differential Formulations on Unstructured Grids

Popular high-order schemes with compact stencils for Computational Fluid Dynamics (CFD) include Discontinuous Galerkin (DG), Spectral Difference (SD), and Spectral Volume (SV) methods. The recently proposed Flux Reconstruction (FR) approach or Correction Procedure using Reconstruction (CPR) is based on a differential formulation and provides a unifying framework for these high-order schemes. Here we present a brief review of recent developments for the FR/CPR schemes as well as some pacing items.

Huynh, H. T.↗
NASA NTRS2018

From S-N to the Paris Law with a New Mixed-Mode Cohesive Fatigue Model

The relationship between fatigue life and fatigue crack propagation rate is explored with a new cohesive damage model. The parameters of the model are obtained from idealizations of S-N diagrams used in engineering design. The model is based on the hypothesis that both stable tearing damage and damage due to cyclic loading are representations of a density of microcracks and, therefore, a single damage variable can describe the state of damage. This assumption implies that the quasi-static cohesive law that describes tearing is also the envelope of the fatigue damage. Fatigue damage within the cohesive envelope is assumed to accumulate at a rate that depends on the displacement jumps. The fatigue model was implemented as a UMAT subroutine for Abaqus cohesive elements by adding fatigue damage accumulation to a cohesive model based on the Turon mixed-mode cohesive laws. The analyses were conducted using a simplified cyclic loading procedure in which the maximum applied load is kept constant and the computational expense of cycling the load is avoided. The predicted propagation rates in mode I and mixed mode were compared to experimental results for IM7/8552 graphite/epoxy tape. Several aspects of the results were investigated, including the effect of R-curves, the stress ratio R, and the difference between displacement control and force control.

Davila, Carlos G.↗
NASA NTRS2018

A Cohesive Fatigue Model Based on the S-N Diagram

The relationship between fatigue life and fatigue crack propagation rate is explored with a new cohesive damage model. The parameters of the model are obtained from idealizations of S-N diagrams used in engineering design. The model is based on the hypothesis that both stable tearing damage and damage due to cyclic loading are representations of a density of microcracks and, therefore, a single damage variable can describe the state of damage. This assumption implies that the quasi-static cohesive law that describes tearing is also the envelope of the fatigue damage. Fatigue damage within the cohesive envelope is assumed to accumulate at a rate that depends on the displacement jumps. The fatigue model was implemented as a UMAT subroutine for Abaqus cohesive elements by adding fatigue damage accumulation to a cohesive model based on the Turon quasi-static cohesive law. The analyses were conducted using a simplified cyclic loading procedure in which the maximum applied load is kept constant and the computational expense of cycling the load is avoided. The predicted propagation rates for a double cantilever beam (DCB) specimen were compared to experimental results for IM7/8552 graphite/epoxy tape.

Dávila, Carlos G.↗
NASA NTRS1994

Data Reduction Procedures for Laser Velocimeter Measurements in Turbomachinery Rotors

Blade-to-blade velocity distributions based on laser velocimeter data acquired in compressor or fan rotors are increasingly used as benchmark data for the verification and calibration of turbomachinery computational fluid dynamics (CFD) codes. Using laser Doppler velocimeter (LDV) data for this purpose, however, must be done cautiously. Aside from the still not fully resolved issue of the seed particle response in complex flowfields, there is an important inherent difference between CFD predictions and LDV blade-to-blade velocity distributions. CFD codes calculate velocity fields for an idealized rotor passage. LDV data, on the other hand, stem from the actual geometry of all blade channels in a rotor. The geometry often varies from channel to channel as a result of manufacturing tolerances, assembly tolerances, and incurred operational damage or changes in the rotor individual blades.

Lepicovsky, Jan↗
NASA NTRS1999

Modeling of polychromatic attenuation using computed tomography reconstructed images

This paper presents a procedure for estimating an accurate model of the CT imaging process including spectral effects. As raw projection data are typically unavailable to the end-user, we adopt a post-processing approach that utilizes the reconstructed images themselves. This approach includes errors from x-ray scatter and the nonidealities of the built-in soft tissue correction into the beam characteristics, which is crucial to beam hardening correction algorithms that are designed to be applied directly to CT reconstructed images. We formulate this approach as a quadratic programming problem and propose two different methods, dimension reduction and regularization, to overcome ill conditioning in the model. For the regularization method we use a statistical procedure, Cross Validation, to select the regularization parameter. We have constructed step-wedge phantoms to estimate the effective beam spectrum of a GE CT-I scanner. Using the derived spectrum, we computed the attenuation ratios for the wedge phantoms and found that the worst case modeling error is less than 3% of the corresponding attenuation ratio. We have also built two test (hybrid) phantoms to evaluate the effective spectrum. Based on these test phantoms, we have shown that the effective beam spectrum provides an accurate model for the CT imaging process. Last, we used a simple beam hardening correction experiment to demonstrate the effectiveness of the estimated beam profile for removing beam hardening artifacts. We hope that this estimation procedure will encourage more independent research on beam hardening corrections and will lead to the development of application-specific beam hardening correction algorithms.

NASA Discipline Musculoskeletal↗
NASA NTRS1996

A High Order Finite Difference Scheme with Sharp Shock Resolution for the Euler Equations

We derive a high-order finite difference scheme for the Euler equations that satisfies a semi-discrete energy estimate, and present an efficient strategy for the treatment of discontinuities that leads to sharp shock resolution. The formulation of the semi-discrete energy estimate is based on a symmetrization of the Euler equations that preserves the homogeneity of the flux vector, a canonical splitting of the flux derivative vector, and the use of difference operators that satisfy a discrete analogue to the integration by parts procedure used in the continuous energy estimate. Around discontinuities or sharp gradients, refined grids are created on which the discrete equations are solved after adding a newly constructed artificial viscosity. The positioning of the sub-grids and computation of the viscosity are aided by a detection algorithm which is based on a multi-scale wavelet analysis of the pressure grid function. The wavelet theory provides easy to implement mathematical criteria to detect discontinuities, sharp gradients and spurious oscillations quickly and efficiently.

Gerritsen, Margot↗
NASA NTRS1978

SPAR data handling utilities

The SPAR computer software system is a collection of processors that perform particular steps in the finite-element structural analysis procedure. The data generated by each processor are stored on a data base complex residing on an auxiliary storage device, and these data are then used by subsequent processors. The SPAR data handling utilities use routines to transfer data between the processors and the data base complex. A detailed description of the data base complex organization is presented. A discussion of how these SPAR data handling utilities are used in an application program to perform desired user functions is given with the steps necessary to convert an existing program to a SPAR processor by incorporating these utilities. Finally, a sample SPAR processor is included to illustrate the use of the data handling utilities.

Giles, G. L.↗
NASA NTRS1982

A computational design method for transonic turbomachinery cascades

This paper describes a systematical computational procedure to find configuration changes necessary to modify the resulting flow past turbomachinery cascades, channels and nozzles, to be shock-free at prescribed transonic operating conditions. The method is based on a finite area transonic analysis technique and the fictitious gas approach. This design scheme has two major areas of application. First, it can be used for design of supercritical cascades, with applications mainly in compressor blade design. Second, it provides subsonic inlet shapes including sonic surfaces with suitable initial data for the design of supersonic (accelerated) exits, like nozzles and turbine cascade shapes. This fast, accurate and economical method with a proven potential for applications to three-dimensional flows is illustrated by some design examples.

Sobieczky, H.↗
NASA NTRS1983

A root locus based flutter synthesis procedure

An efficient generalized constraint is proposed in the context of a nonlinear mathematical programming approach for the minimum weight design of wing structures for flutter considerations. The approach is based on a root locus analysis procedure that is better suited for flutter redesign than the conventionally used V-g method. The proposed flutter constraint does not require an actual computation of the flutter speed, allows prescription of meaningful margins of safety in the optimized design and lends itself to elegant computation of sensitivity information. The approach is implemented and results presented for representative structural models.

Hajela, P.↗
NASA NTRS1985

Seismic analysis of the large 70-meter antenna. Part 2: General dynamic response and a seismic safety check

An extensive dynamic analysis for the new JPL 70-meter antenna structure is presented. Analytical procedures are based on the normal mode decomposition which include dumping and special forcing functions. The dynamic response can be obtained for any arbitrarily selected point on the structure. A new computer program for computing the time-dependent, resultant structural displacement, summing the effects of all participating modes, was developed also. Program compatibility with natural frequency analysis output was verified. The program was applied to the JPL 70-meter antenna structure and the dynamic response for several specially selected points was computed. Seismic analysis of structures, a special application of the general dynamic analysis, is based also on the normal modal decomposition. Strength specification of the antenna, with respect to the earthquake excitation, is done by using the common response spectra. The results indicated basically a safe design under an assumed 5% or more damping coefficient. However, for the antenna located at Goldstone, with more active seismic environment, this study strongly recommends and experimental program that determines the true damping coefficient for a more reliable safety check.

Kiedron, K.↗
NASA NTRS1986

Evaluation of automated decision making methodologies and development of an integrated robotic system simulation: Study results

The implementation of a generic computer simulation for manipulator systems (ROBSIM) is described. The program is written in FORTRAN, and allows the user to: (1) Interactively define a manipulator system consisting of multiple arms, load objects, targets, and an environment; (2) Request graphic display or replay of manipulator motion; (3) Investigate and simulate various control methods including manual force/torque and active compliance control; and (4) Perform kinematic analysis, requirements analysis, and response simulation of manipulamotion. Previous reports have described the algorithms and procedures for using ROBSIM. These reports are superseded and additional features which were added are described. They are: (1) The ability to define motion profiles and compute loads on a common base to which manipulator arms are attached; (2) Capability to accept data describing manipulator geometry from a Computer Aided Design data base using the Initial Graphics exchange Specification format; (3) A manipulator control algorithm derived from processing the TV image of known reference points on a target; and (4) A vocabulary of simple high level task commands which can be used to define task scenarios.

Haley, D. C.↗