Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computing, Lattice”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Experimental and theoretical study of three interacting, closely-spaced, sharp-edged 60 deg delta wings at low speeds

Wind tunnel tests were conducted to determine the subsonic longitudinal aerodynamic characteristics of lifting configuration consisting of a 60 deg delta main wing with two smaller 60 deg delta wings (called sub-wings) attached underneath. The test was designed to determine the effects on lift, drag, and pitching moment due to various placement of the subwings in relation to the main wing. Test results indicate the increasing vertical separation between the main wing and the sub-wings produced the most significant results; a 23.1% increase in maximum lift coefficient, a reduction in drag coefficient at high lift coefficients, and an increase in longitudinal stability. Lateral separation of the sub-wings produced no significant changes. Placement of the sub-wings rearward increases the initial lift curve slope and maximum lift coefficient and also increase the longitudinal stability. Results of a computer study using a vortex lattice code supported the experimental conclusions.

Faery, H. F., Jr.↗

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗

Evaluation of the constant pressure panel method (CPM) for unsteady air loads prediction

This paper evaluates the capability of the constant pressure panel method (CPM) code to predict unsteady aerodynamic pressures, lift and moment distributions, and generalized forces for general wing-body configurations in supersonic flow. Stability derivatives are computed and correlated for the X-29 and an Oblique Wing Research Aircraft, and a flutter analysis is carried out for a wing wind tunnel test example. Most results are shown to correlate well with test or published data. Although the emphasis of this paper is on evaluation, an improvement in the CPM code's handling of intersecting lifting surfaces is briefly discussed. An attractive feature of the CPM code is that it shares the basic data requirements and computational arrangements of the doublet lattice method. A unified code to predict unsteady subsonic or supersonic airloads is therefore possible.

Appa, Kari↗

Progress in the Modeling of NiAl-Based Alloys Using the BFS Method

The BFS method has been applied to the study of NiAl-based materials to assess the effect of alloying additions on structure. Ternary, quaternary and even pent-alloys based on Ni-rich NiAl with additions of Ti, Cr and Cu were studied. Two approaches were used, Monte Carlo simulations to determine ground state structures and analytical calculations of high symmetry configurations which give physical insight into preferred bonding. Site occupancy energetics for ternary and the more complicated case of quaternary additions were determined, and solubility limits and precipitate formation with corresponding information concerning structure and lattice parameter were also 'observed' computationally. The method was also applied to determine the composition of alloy surfaces and interfaces. Overall, the results demonstrate that the BFS method for alloys is a powerful tool for alloy design and with its simplicity and obvious advantages can be used to complement any experimental alloy design program.

Bozzolo, Guillermo↗

Experimental Verification of the Theoretical Prediction of the Phase Structure of a Ni-Al-Ti-Cr-Cu Alloy

The Bozzolo-Ferrante-Smith (BFS) method for alloys was applied to the study of NiAl-based materials to assess the effect of alloying additions on structure. Ternary, quaternary and even pentalloys based on NiAl with additions of Ti, Cr and Cu were studied and experimental verification of the theoretical predictions including the phase structure of a Ni-Al-Ti-Cr-Cu alloy is presented. Two approaches were used, Monte Carlo simulations to determine low energy structures, and analytical calculations of the energy of high symmetry configurations which give physical insight into preferred structures. The energetics for site occupancy in ternary and quaternary systems were calculated leading to an indirect determination of solubility limits at 0 K. Precipitate formation with information concerning structure and lattice parameter were also 'observed' computationally and the general characteristics of a Ni-Al-Ti-Cr-Cu alloy were correctly predicted. The results indicate that the BFS method for alloys can be a useful tool for alloy design and can be used to complement experimental alloy design programs.

Wilson, A.↗

Rapid State Space Modeling Tool for Rectangular Wing Aeroservoelastic Studies

This paper introduces a modeling and simulation tool for aeroservoelastic analysis of rectangular wings with trailing edge control surfaces. The inputs to the code are planform design parameters such as wing span, aspect ratio and number of control surfaces. A doublet lattice approach is taken to compute generalized forces. A rational function approximation is computed. The output, computed in a few seconds, is a state space aeroservoelastic model which can be used for analysis and control design. The tool is fully parameterized with default information so there is little required interaction with the model developer. Although, all parameters can be easily modified if desired.The focus of this paper is on tool presentation, verification and validation. This process is carried out in stages throughout the paper. The rational function approximation is verified against computed generalized forces for a plate model. A model composed of finite element plates is compared to a modal analysis from commercial software and an independently conducted experimental ground vibration test analysis. Aeroservoelastic analysis is the ultimate goal of this tool. Therefore the flutter speed and frequency for a clamped plate are computed using V-g and V-f analysis. The computational results are compared to a previously published computational analysis and wind tunnel results for the same structure. Finally a case study of a generic wing model with a single control surface is presented. Verification of the state space model is presented in comparison to V-g and V-f analysis. This also includes the analysis of the model in response to a 1-cos gust.

Modeling and Simulation↗

Comparative Study of Active Flow Control Strategies for Lift Enhancement of a Simplified High-Lift Configuration

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of the conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to recover the aerodynamic performance (lift) of the CRM-HL configuration. In the current paper, a Lattice Boltzmann method-based computational fluid dynamics (CFD) code, known as PowerFLOWQ® is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOWQ® code that has been validated for high speed flows is used to accurately simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient AFC systems and actuator arrangements emerged based on the parametric studies performed prior to a Fall 2018 wind tunnel test. Preliminary comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations.

Vatsa, Veer N.↗

Meson and Baryon Spectroscopy on the Lattice

Recent progress at understanding the excited state spectrum of mesons and baryons is described. I begin by outlining the application of the variational method to compute the spectrum, and the program of anisotropic clover lattice generation designed for hadron spectroscopy. I present results for the excited meson spectrum, with continuum quantum numbers of the states clearly delineated. I conclude with recent results for the low lying baryon spectrum, and the prospects for future calculations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Development of Ultra-Fine Multigroup Cross Section Library of the AMPX/SCALE Code Packages

The Consortium for Advanced Simulation of Light Water Reactors Virtual Environment for Reactor Applications (VERA) neutronic simulator MPACT is being developed by Oak Ridge National Laboratory and the University of Michigan for various reactor applications. The MPACT and simplified MPACT 51- and 252-group cross section libraries have been developed for the MPACT neutron transport calculations by using the AMPX and Standardized Computer Analyses for Licensing Evaluations (SCALE) code packages developed at Oak Ridge National Laboratory. It has been noted that the conventional AMPX/SCALE procedure has limited applications for fast-spectrum systems such as boiling water reactor (BWR) fuels with very high void fractions and fast reactor fuels because of its poor accuracy in unresolved and fast energy regions. This lack of accuracy can introduce additional error sources to MPACT calculations, which is already limited by the Bondarenko approach for resolved resonance self-shielding calculation. To enhance the prediction accuracy of MPACT for fast-spectrum reactor analyses, the accuracy of the AMPX/SCALE code packages should be improved first. The purpose of this study is to identify the major problems of the AMPX/SCALE procedure in generating fast-spectrum cross sections and to devise ways to improve the accuracy. For this, various benchmark problems including a typical pressurized water reactor fuel, BWR fuels with various void fractions, and several fast reactor fuels were analyzed using the AMPX 252-group libraries. Isotopic reaction rates were determined by SCALE multigroup (MG) calculations and compared with continuous energy (CE) Monte Carlo calculation results. This reaction rate analysis revealed three main contributors to the observed differences in reactivity and reaction rates: (1) the limitation of the Bondarenko approach in coarse energy group structure, (2) the normalization issue of probability tables, and (3) neglect of the self-shielding effect of resonance-like cross sections at high energy range such as (n,p) cross section of Cl35. The first error source can be eliminated by an ultra-fine group (UFG) structure in which the broad scattering resonances of intermediate-weight nuclides can be represented accurately by a piecewise constant function. A UFG AMPX library was generated with modified probability tables and tested against various benchmark problems. The reactivity and reaction rates determined with the new UFG AMPX library agreed very well with respect to Monte Carlo Neutral Particle (MCNP) results. To enhance the lattice calculation accuracy without significantly increasing the computational time, performing the UFG lattice calculation in two steps was proposed. In the first step, a UFG slowing-down calculation is performed for the corresponding homogenized composition, and UFG cross sections are collapsed into an intermediate group structure. In the second step, the lattice calculation is performed for the intermediate group level using the condensed group cross sections. A preliminary test showed that the condensed library reproduces the results obtained with the UFG cross section library. This result suggests that the proposed two-step lattice calculation approach is a promising option to enhance the applicability of the AMPX/SCALE system to fast system analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Parallelizing the QUDA Library for Multi-GPU Calculations in Lattice Quantum Chromodynamics

Graphics Processing Units (GPUs) are having a transformational effect on numerical lattice quantum chromodynamics (LQCD) calculations of importance in nuclear and particle physics. The QUDA library provides a package of mixed precision sparse matrix linear solvers for LQCD applications, supporting single GPUs based on NVIDIA's Compute Unified Device Architecture (CUDA). This library, interfaced to the QDP++/Chroma framework for LQCD calculations, is currently in production use on the "9g" cluster at the Jefferson Laboratory, enabling unprecedented price/performance for a range of problems in LQCD. Nevertheless, memory constraints on current GPU devices limit the problem sizes that can be tackled. In this contribution we describe the parallelization of the QUDA library onto multiple GPUs using MPI, including strategies for the overlapping of communication and computation. We report on both weak and strong scaling for up to 32 GPUs interconnected by InfiniBand, on which we sustain in excess of 4 Tflops.

43 PARTICLE ACCELERATORS↗

Thorium and Rare Earth Monoxides and Related Phases

Thorium was a part of energy infrastructure in the 19th century due to the refractory and electronic properties of its dioxide. It will be a part of future energy infrastructure as the most abundant energy reserve based on nuclear fission. This paper discusses the solid-state chemistry of the monoxides and related rocksalt phases of thorium and the rare earths, both at atmospheric and at high pressure. The existence of solid thorium monoxide was first suggested more than 100 years ago; however, it was never obtained in bulk and has been studied mostly theoretically. Monoxides of lanthanides from Eu to Ho are ferromagnetic semiconductors sought for spintronics and were studied in thin films. La to Sm metallic monoxides were synthesized in bulk at pressures below 5 GPa. Recently, ThO formation in thin films has been reported and the stability of bulk ThO at high pressure was theoretically predicted based on first principles computations at 0 K. New ab initio computations were performed accounting for temperature effects up to 1000 K using lattice dynamics in the quasi-harmonic approximation. New computational results confirm the stabilization of pure ThO above 30 GPa and suggest the possibility of high-pressure synthesis of (Th,Nd)O at 1000 K and 5 GPa.

36 MATERIALS SCIENCE↗

Multi-baryon systems

In this talk I review the challenges related to calculations of properties of interacting baryons on the lattice. I present the progress made addressing the problem of calculating the large number of Wick contractions necessary to compute states with the quantum numbers of many baryons in lattice QCD. Examples of correlation functions computed using these techniques are shown for the quantum numbers of the light nuclei, He-4, Be-8, C-12, O-16 and Si-28.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Analysis of static Wilson line correlators from lattice QCD at finite temperature with T -matrix approach

The thermodynamic T-matrix approach is used to study Wilson line correlators (WLCs) for a static quark-antiquark pair in the quark-gluon plasma (QGP). Selfconsistent results that incorporate constraints from the QGP equation of state can approximately reproduce WLCs computed in 2+1-flavor lattice-QCD (lQCD), provided the input potential exhibits less screening than in previous studies. Utilizing the updated potential to calculate pertinent heavylight T-matrices we evaluate thermal relaxation rates of heavy quarks in the QGP. We find a more pronounced temperature dependence for low-momentum quarks than in our previous results (with larger screening), which turns into a weaker temperature dependence of the (temperature-scaled) spatial diffusion coefficient, in fair agreement with the most recent lQCD data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Revisiting the empirical particle-fluid coupling model used in DEM-CFD by high-resolution DEM-LBM-IMB simulations: A 2D perspective

The work investigates the applicability of the unresolved Computational Fluid Dynamics and Discrete Element Method (CFDDEM) technique based on empirical equations for fluid-particle coupling. We first carry out a series of representative volume element simulations using the high-resolution particle-resolved Lattice Boltzmann method and Discrete Element Method (LBMDEM) coupled by an Immersed Moving Boundary (IMB) scheme. Then, we compare the results obtained by both LBMDEM and empirical equations used in unresolved CFDDEM with analytical solutions. It is found that the existing empirical equations used in solving fluid-particle interactions in 2D CFDDEM fail to accurately calculate the hydrodynamic force applied to solid particles. The underlying reason is that the existing empirical models are obtained based on 3D experimental results and thus are not applicable to 2D problems. Based on the simulation results, a new drag coefficient model is then proposed. The estimated drag forces using the new model are compared favourably with the simulated ones, indicating the good performance of the proposed model.

42 ENGINEERING↗

Structure of the Pion from First Principles Calculation in Lattice QCD

I describe the recent progress by the HadStruct Collaboration aimed at computing the structure of the pion from first-principles calculation in lattice QCD. I begin by presenting the Pseudo-PDF and Lattice Cross Section approaches, emphasizing that they are formulated in terms of Lorentz invariants with a short-distance scale to admit factorization. I present resent results on the pion PDF using both approaches, and compare with phenomenological determinations and other theoretical approaches. I conclude with plans for future work.

Richards, David↗

PyFly: A fast, portable aerodynamics simulator

Here, we present a fast, user-friendly implementation of a potential flow solver based on the unsteady vortex lattice method (UVLM), namely PyFly. UVLM computes the aerodynamic loads applied on lifting surfaces while capturing the unsteady effects such as the added mass forces, the growth of bound circulation, and the wake while assuming that the flow separation location is known a priori. This method is based on discretizing the body surface into a lattice of vortex rings and relies on the Biot–Savart law to construct the velocity field at every point in the simulated domain. We introduce the pointwise approximation approach to simulate the interactions of the far-field vortices to overcome the computational burden associated with the classical implementation of UVLM. The computational framework uses the Python programming language to provide an easy to handle user interface while the computational kernels are written in Fortran. The mixed language approach enables high performance regarding solution time and great flexibility concerning easiness of code adaptation to different system configurations and applications. The computational tool predicts the unsteady aerodynamic behavior of multiple moving bodies (e.g., flapping wings, rotating blades, suspension bridges) subject to incoming air. The aerodynamic simulator can also deal with enclosure effects, multi-body interactions, and B-spline representation of body shapes. Finally, we simulate different aerodynamic problems to illustrate the usefulness and effectiveness of PyFly.

97 MATHEMATICS AND COMPUTING↗