Brayton cycle solar collector design study
Brayton cycle solar collector design, mirror analysis, design, manufacture, and performance of concentrator, structural integrity, and reliability
SOLAR COLLECTOR↗
SEARCH · Search NASA
Results for “Design analysis”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Lean, premixed, prevaporized combustor conceptual design study
The seven month study program has the objective to identify and evaluate promising lean, premixed, prevaporized combustor concepts utilizing variable geometry and/or other flow control techniques. The general approach taken to accomplish this objective is outlined and consists of combustor design, design analysis and design ranking. The schedule being taken to achieve this program is shown. Although the ultimate goal of this program is the significant reduction of cruise oxides of nitrogen, both the EPA emission standards and combustor performance levels outlined are retained as goals as well.
Fiorentino, A. J.↗
High-Pressure Hot-Gas Self-Acting Floating Ring Shaft Seal for Liquid Rocket Turbopumps
Design analysis, detail design, fabrication, and experimental evaluation was performed on two self acting floating ring shaft seals for a rocket engine turbopump high pressure 24132500 n/sq m (3500 psig) hot gas 533 K 9500 F) high speed 3142 rad/sec (30000 rmp) turbine. The initial design used Rayleigh step hydrodynamic lift pads to assist in centering the seal ring with minimum rubbing contact. The final design used a convergent tapered bore to provide hydrostatic centering force. The Rayleigh step design was tested for 107 starts and 4.52 hours total. The leakage was satisfactory; however, the design was not acceptable due to excessive wear caused by inadequate centering force and failure of the sealing dam caused by erosion damage. The tapered bore design was tested for 370 starts and 15.93 hours total. Satisfactory performance for the required life of 7.5 hours per seal was successfully demonstrated.
Burcham, R. E.↗
A review of modern approaches to fatigue reliability analysis and design
Metal fatigue is a principal mode of failure in components of mechanical systems. But fatigue design factors (e.g., stress, fatigue strength) are subject to considerable uncertainty. Therefore, relative to fatigue, reliability methods are appropriate for purposes of safety checking of designs, risk assessment, failure analysis, and development of code statements. Described herein are four methods which can be effectively employed for fatigue reliability analysis, (1) Monte Carlo methods, (2) the lognormal format, (3) the Weibull format, (4) the Rackwitz-Fiessler algorithm. Examples of the application of each are presented. In summary, no general reliability method can be recommended for all situations involving fatigue. The approach has to be tailored to the problem.
Wirsching, P. H.↗
EHD analysis of and experiments on pumping Leningrader seals
Analysis and design charts have been generated to provide design data for Pumping Leningrader Reciprocating Rod Seals. The analytical treatment divides the seal into three regions: an inlet zone, induced with the use of an expansion ring, a contact zone, and an exit zone. Complete solutions have been obtained by matching elasticity equations with hydrodynamic theory. Experiments, although of a limited nature, did demonstrate the ability of the seal design analysis to provide viable seals.
Eusepi, M. W.↗
Unified Engineering Software System
Collection of computer programs performs diverse functions in prototype engineering. NEXUS, NASA Engineering Extendible Unified Software system, is research set of computer programs designed to support full sequence of activities encountered in NASA engineering projects. Sequence spans preliminary design, design analysis, detailed design, manufacturing, assembly, and testing. Primarily addresses process of prototype engineering, task of getting single or small number of copies of product to work. Written in FORTRAN 77 and PROLOG.
Purves, L. R.↗
Computational mechanics analysis tools for parallel-vector supercomputers
Computational algorithms for structural analysis on parallel-vector supercomputers are reviewed. These parallel algorithms, developed by the authors, are for the assembly of structural equations, 'out-of-core' strategies for linear equation solution, massively distributed-memory equation solution, unsymmetric equation solution, general eigensolution, geometrically nonlinear finite element analysis, design sensitivity analysis for structural dynamics, optimization search analysis and domain decomposition. The source code for many of these algorithms is available.
Storaasli, Olaf O.↗
Automatic differentiation for design sensitivity analysis of structural systems using multiple processors
An automatic differentiation tool (ADIFOR) is incorporated into a finite element based structural analysis program for shape and non-shape design sensitivity analysis of structural systems. The entire analysis and sensitivity procedures are parallelized and vectorized for high performance computation. Small scale examples to verify the accuracy of the proposed program and a medium scale example to demonstrate the parallel vector performance on multiple CRAY C90 processors are included.
Nguyen, Duc T.↗
Computational mechanics analysis tools for parallel-vector supercomputers
Computational algorithms for structural analysis on parallel-vector supercomputers are reviewed. These parallel algorithms, developed by the authors, are for the assembly of structural equations, 'out-of-core' strategies for linear equation solution, massively distributed-memory equation solution, unsymmetric equation solution, general eigen-solution, geometrically nonlinear finite element analysis, design sensitivity analysis for structural dynamics, optimization algorithm and domain decomposition. The source code for many of these algorithms is available from NASA Langley.
Storaasli, O. O.↗
Design and Analysis Techniques for JPL Mobile Antenna Developments
Explore the source record for details and available documents.
mathematical analysis conventional design techniqu↗
Turbine Seal Research at NASA GRC
Low-leakage, long-life turbomachinery seals are important to both Space and Aeronautics Missions. (1) Increased payload capability (2) Decreased specific fuel consumption and emissions (3) Decreased direct operating costs. NASA GRC has a history of significant accomplishments and collaboration with industry and academia in seals research. NASA's unique, state-of-the-art High Temperature, High Speed Turbine Seal Test Facility is an asset to the U.S. Engine / Seal Community. Current focus is on developing experimentally validated compliant, non-contacting, high temperature seal designs, analysis, and design methodologies to enable commercialization.
Proctor, Margaret P.↗
Performance (Off-Design) Cycle Analysis for a Turbofan Engine With Interstage Turbine Burner
This report presents the performance of a steady-state, dual-spool, separate-exhaust turbofan engine, with an interstage turbine burner (ITB) serving as a secondary combustor. The ITB, which is located in the transition duct between the high- and the low-pressure turbines, is a relatively new concept for increasing specific thrust and lowering pollutant emissions in modern jet-engine propulsion. A detailed off-design performance analysis of ITB engines is written in Microsoft(Registered Trademark) Excel (Redmond, Washington) macrocode with Visual Basic Application to calculate engine performances over the entire operating envelope. Several design-point engine cases are pre-selected using a parametric cycle-analysis code developed previously in Microsoft(Registered Trademark) Excel, for off-design analysis. The off-design code calculates engine performances (i.e. thrust and thrust-specific-fuel-consumption) at various flight conditions and throttle settings.
Liew, K. H.↗
Reliability Sensitivity Analysis and Design Optimization of Composite Structures Based on Response Surface Methodology
This report discusses the development and application of two alternative strategies in the form of global and sequential local response surface (RS) techniques for the solution of reliability-based optimization (RBO) problems. The problem of a thin-walled composite circular cylinder under axial buckling instability is used as a demonstrative example. In this case, the global technique uses a single second-order RS model to estimate the axial buckling load over the entire feasible design space (FDS) whereas the local technique uses multiple first-order RS models with each applied to a small subregion of FDS. Alternative methods for the calculation of unknown coefficients in each RS model are explored prior to the solution of the optimization problem. The example RBO problem is formulated as a function of 23 uncorrelated random variables that include material properties, thickness and orientation angle of each ply, cylinder diameter and length, as well as the applied load. The mean values of the 8 ply thicknesses are treated as independent design variables. While the coefficients of variation of all random variables are held fixed, the standard deviations of ply thicknesses can vary during the optimization process as a result of changes in the design variables. The structural reliability analysis is based on the first-order reliability method with reliability index treated as the design constraint. In addition to the probabilistic sensitivity analysis of reliability index, the results of the RBO problem are presented for different combinations of cylinder length and diameter and laminate ply patterns. The two strategies are found to produce similar results in terms of accuracy with the sequential local RS technique having a considerably better computational efficiency.
Rais-Rohani, Masoud↗
Study of design and analysis methods for transonic flow
An airfoil design program and a boundary layer analysis were developed. Boundary conditions were derived for ventilated transonic wind tunnels and performing transonic windtunnel wall calculations. A computational procedure for rotational transonic flow in engine inlet throats was formulated. Results and conclusions are summarized.
Murman, E. M.↗
Analysis and design of transonic airfoils using streamwise coordinates
A new approach is developed for analysis and design of transonic airfoils. A set of full potential equivalent equations in von Mises coordinates is formulated from the Euler equations under the irrotationality and isentropic assumptions. This set is composed of a main equation for the main variable, y, and a secondary equations for the secondary variable, R. The main equation is solved by type dependent differencing combined with a shock point operator. The secondary equation is solved by marching from a non-characteristic boundary. Sample computations on NACA 0012 and biconvex airfoils show that, for the analysis problem, the present approach achieves good agreement with experimental C sub p distributions. For the design problem, the approach leads to a simple numerical algorithm in which the airfoil contour is calculated as part of the flow field solution.
Barron, R. M.↗
Improvements in surface singularity analysis and design methods
The coupling of the combined source vortex distribution of Green's potential flow function with contemporary numerical techniques is shown to provide accurate, efficient, and stable solutions to subsonic inviscid analysis and design problems for multi-element airfoils. The analysis problem is solved by direct calculation of the surface singularity distribution required to satisfy the flow tangency boundary condition. The design or inverse problem is solved by an iteration process. In this process, the geometry and the associated pressure distribution are iterated until the pressure distribution most nearly corresponding to the prescribed design distribution is obtained. Typically, five iteration cycles are required for convergence. A description of the analysis and design method is presented, along with supporting examples.
Bristow, D. R.↗
Factors which influence the analysis and design of ejector nozzles
A theoretical analysis of the viscous interaction between the primary and secondary streams of ejector nozzles was developed. The analysis accounts for real sonic line effects and the streamwise variation in stream mixing and boundary layer within the ejector. The aspects of the analysis are explained and illustrated by applying the theory to a variety of ejector configurations including cylindrical shroud, contoured flap and plug nozzles. Extensive comparisons are made between theory and data to show the importance of various analytical assumptions and such design variables as diameter ratio, spacing ratio, total temperature ratio, and primary nozzle geometry.
Anderson, B. H.↗
Factors which influence the analysis and design of ejector nozzles.
A theoretical analysis of the viscous interaction between the primary and secondary streams of ejector nozzles was developed. The analysis accounts for real sonic-line effects and the streamwise variation in stream mixing and boundary layer within the ejector. The aspects of the analysis are explained and illustrated by applying the theory to a variety of ejector configurations including cylindrical shroud, contoured flap and plug nozzles. Extensive comparisons are made between theory and data to show the importance of various analytical assumptions and such design variables as diameter ratio, spacing ratio, total temperature ratio, and primary nozzle geometry.
Anderson, B. H.↗