Results for “Edge Based” — Page 29

NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading- and Trailing-Edge Slot Blowing

The AMELIA Cruise-Efficient Short Take-off and Landing (CESTOL) configuration concept was developed to meet future requirements of reduced field length, noise, and fuel burn by researchers at Cal Poly, San Luis Obispo and Georgia Tech Research Institute under sponsorship by the NASA Fundamental Aeronautics Program (FAP), Subsonic Fixed Wing Project. The novel configuration includes leading- and trailing-edge circulation control wing (CCW), over-wing podded turbine propulsion simulation (TPS). Extensive aerodynamic measurements of forces, surfaces pressures, and wing surface skin friction measurements were recently measured over a wide range of test conditions in the Arnold Engineering Development Center(AEDC) National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Ft Wind Tunnel. Acoustic measurements of the model were also acquired for each configuration with 7 fixed microphones on a line under the left wing, and with a 48-element, 40-inch diameter phased microphone array under the right wing. This presentation will discuss acoustic characteristics of the CCW system for a variety of tunnel speeds (0 to 120 kts), model configurations (leading edge(LE) and/or trailing-edge(TE) slot blowing, and orientations (incidence and yaw) based on acoustic measurements acquired concurrently with the aerodynamic measurements. The flow coefficient, Cmu= mVSLOT/qSW varied from 0 to 0.88 at 40 kts, and from 0 to 0.15 at 120 kts. Here m is the slot mass flow rate, VSLOT is the slot exit velocity, q is dynamic pressure, and SW is wing surface area. Directivities at selected 1/3 octave bands will be compared with comparable measurements of a 2-D wing at GTRI, as will as microphone array near-field measurements of the right wing at maximum flow rate. The presentation will include discussion of acoustic sensor calibrations as well as characterization of the wind tunnel background noise environment.

Horne, William C.↗

NASA NTRS2015

Reinforcement Learning with Autonomous Small Unmanned Aerial Vehicles in Cluttered Environments

We present ongoing work in the Autonomy Incubator at NASA Langley Research Center (LaRC) exploring the efficacy of a data set aggregation approach to reinforcement learning for small unmanned aerial vehicle (sUAV) flight in dense and cluttered environments with reactive obstacle avoidance. The goal is to learn an autonomous flight model using training experiences from a human piloting a sUAV around static obstacles. The training approach uses video data from a forward-facing camera that records the human pilot's flight. Various computer vision based features are extracted from the video relating to edge and gradient information. The recorded human-controlled inputs are used to train an autonomous control model that correlates the extracted feature vector to a yaw command. As part of the reinforcement learning approach, the autonomous control model is iteratively updated with feedback from a human agent who corrects undesired model output. This data driven approach to autonomous obstacle avoidance is explored for simulated forest environments furthering autonomous flight under the tree canopy research. This enables flight in previously inaccessible environments which are of interest to NASA researchers in Earth and Atmospheric sciences.

Tran, Loc↗

NASA NTRS2003

Fretting Fatigue of Gamma TiAl Studied

Gamma titanium-aluminum alloy (g-TiAl) is an attractive new material for aerospace applications because of its low density and high specific strength in comparison to currently used titanium and nickel-base alloys. Potential applications for this material are compressor and low-pressure turbine blades. These blades are fitted into either the compressor or turbine disks via a dovetail connection. The dovetail region experiences a complex stress state due to the alternating centrifugal force and the natural high-frequency vibration of the blade. Because of the dovetail configuration and the complex stress state, fretting is often a problem in this area. Furthermore, the local stress state becomes more complex when the influence of the metal-metal contact and the edge of the contact is evaluated. Titanium and titanium-based alloys in the clean state exhibit strong adhesive bonds when in contact with themselves and other materials (refs. 1 and 2). This adhesion causes heavy surface damage and high friction in practical cases. Although the wear produced by fretting may be mild, the reduction in fatigue life can be substantial. Thus, there is the potential for fretting problems with these TiAl applications. Since TiAl is an emerging material, there has been limited information about its fretting behavior.

Miyoshi, Kazuhisa↗

NASA NTRS2004

Test and Analysis Correlation of Form Impact onto Space Shuttle Wing Leading Edge RCC Panel 8

Soon after the Columbia Accident Investigation Board (CAIB) began their study of the space shuttle Columbia accident, "physics-based" analyses using LS-DYNA were applied to characterize the expected damage to the Reinforced Carbon-Carbon (RCC) leading edge from high-speed foam impacts. Forensic evidence quickly led CAIB investigators to concentrate on the left wing leading edge RCC panels. This paper will concentrate on the test of the left-wing RCC panel 8 conducted at Southwest Research Institute (SwRI) and the correlation with an LS-DYNA analysis. The successful correlation of the LS-DYNA model has resulted in the use of LS-DYNA as a predictive tool for characterizing the threshold of damage for impacts of various debris such as foam, ice, and ablators onto the RCC leading edge for shuttle return-to-flight.

Fasanella, Edwin L.↗

NASA NTRS1958

A Body Modification to Reduce Drag Due to Wedge Angle of Wing with Unswept Trailing Edge

Ward's slender-body-theory formula for zero-lift drag contains three integrals plus a base-drag term. Two of these integral terms depend only upon the cross-sectional area distribution of the body. The third integral term depends only upon the body shape and axial slopes at the base of the body. This term is neglected in the transonic area rule because in many cases it is zero; however, there are also many cases in which it is not zero. This paper examines the term for the possibility of drag reduction for a particular case. The model considered consists of a body of revolution in combination with any wing that has an unswept trailing edge and a constant trailing-edge angle along its span. It is found that (neglecting any change in base drag) a drag reduction is obtainable which, for the case considered, is an additional 12 percent of that obtained with the area-rule modification. The probable effect of viscosity on this theoretical result is discussed.

Pitts, William C.↗

NASA NTRS1972

On the mechanism of dynamic stall.

The sequence of events comprising dynamic stall of an airfoil is discussed, with emphasis on the role of the leading edge laminar separation bubble and shed vortex. A simple bubble model, based on a combination of theoretical and experimental investigations, is used to discuss the events prior to the shedding of the vortex, and provides the basis for a heuristic estimate of the delay in the occurrence of dynamic stall on a pitching airfoil. The evidence for the existence and dominant effect of the leading edge vortex on the dynamic stall required (but in most cases not presently available) for the prediction of the effects of stall on helicopter rotor blades are discussed. It is the intention of this paper to focus attention on the laminar separation bubble and the shed leading edge vortex as the dominant features of the dynamic stall mechanism in the hope of stimulating greater emphasis on these features in future dynamic stall research.

Johnson, W.↗

NASA NTRS1983

The evolution of spokes in Saturn's B ring

Three types of Saturnian ring spoke structure have been observed which are distinguished by their optical appearance. Extended spokes are found inside the corotation radius. They are of irregular shape, with diffuse edges, but often narrowed at large distances. Their width at the base is typically 20,000 km, and their radial extent is 8000 km. The random velocity of their particles is about 2 m/s, and the total kinetic energy of their random velocity component is about 20 billion J. Narrow spokes are observed to cross the corotation distance and are characterized by high-contrast edges. Their number of particles and total energy content are about 10 percent of the values for extended spokes. Filamentary spokes are observed outside approximately 110,000 km and are usually connected to narrow or extended spokes further in. Their width is typically 500 km and their length is about 3000 km. Their number of particles and total energy content are about 0.5 percent of those of an extended spoke.

Gruen, E.↗

NASA NTRS2015

A Model for Jet-Surface Interaction Noise Using Physically Realizable Upstream Turbulence Conditions

This paper is a continuation of previous work in which a generalized Rapid Distortion Theory (RDT) formulation was used to model low-frequency trailing-edge noise. The research was motivated by proposed next-generation aircraft configurations where the exhaust system is tightly integrated with the airframe. Data from recent experiments at NASA on the interaction between high-Reynolds-number subsonic jet flows and an external flat plate showed that the power spectral density (PSD) of the far-field pressure underwent considerable amplification at low frequencies. For example, at the 900 observation angle, the low-frequency noise could be as much as 10dB greater than the jet noise itself. In this paper, we present predictions of the noise generated by the interaction of a rectangular jet with the trailing edge of a semi-infinite flat plate. The calculations are based on a formula for the acoustic spectrum of this noise source derived from an exact formal solution of the linearized Euler equations involving (in this case) one arbitrary convected scalar quantity and a Rayleigh equation Green's function. A low-frequency asymptotic approximation for the Green's function based on a two-dimensional mean flow is used in the calculations along with a physically realizable upstream turbulence spectrum, which includes a finite de-correlation region. Numerical predictions, based on three-dimensional RANS solutions for a range of subsonic acoustic Mach number jets and nozzle aspect ratios are compared with experimental data. Comparisons of the RANS results with flow data are also presented for selected cases. We find that a finite decorrelation region increases the low-frequency algebraic decay (the low frequency "rolloff") of the acoustic spectrum with angular frequency thereby producing much closer agreement with noise data for Strouhal numbers less than 0.1. Secondly, the large-aspectratio theory is able to predict the low-frequency amplification due to the jet-edge interaction reasonably well, even for moderate aspect ratio nozzles. We show also that the noise predictions for smaller aspect ratio jets can be fine-tuned using the appropriate RANS-based mean flow and turbulence properties.

Jet↗

NASA NTRS2015

A Model for Jet-Surface Interaction Noise Using Physically Realizable Upstream Turbulence Conditions

This paper is a continuation of previous work in which a generalized Rapid Distortion Theory (RDT) formulation was used to model low-frequency trailing-edge noise. The research was motivated by proposed next-generation aircraft configurations where the exhaust system is tightly integrated with the airframe. Data from recent experiments at NASA on the interaction between high-Reynolds-number subsonic jet flows and an external flat plate showed that the power spectral density (PSD) of the far-field pressure underwent considerable amplification at low frequencies. For example, at the 900 observation angle, the low-frequency noise could be as much as 10dB greater than the jet noise itself. In this paper, we present predictions of the noise generated by the interaction of a rectangular jet with the trailing edge of a semi-infinite flat plate. The calculations are based on a formula for the acoustic spectrum of this noise source derived from an exact formal solution of the linearized Euler equations involving (in this case) one arbitrary convected scalar quantity and a Rayleigh equation Green's function. A low-frequency asymptotic approximation for the Green's function based on a two-dimensional mean flow is used in the calculations along with a physically realizable upstream turbulence spectrum, which includes a finite de-correlation region. Numerical predictions, based on three-dimensional RANS solutions for a range of subsonic acoustic Mach number jets and nozzle aspect ratios are compared with experimental data. Comparisons of the RANS results with flow data are also presented for selected cases. We find that a finite decorrelation region increases the low-frequency algebraic decay (the low frequency "rolloff") of the acoustic spectrum with angular frequency thereby producing much closer agreement with noise data for Strouhal numbers less than 0.1. Secondly, the large-aspectratio theory is able to predict the low-frequency amplification due to the jet-edge interaction reasonably well, even for moderate aspect ratio nozzles. We show also that the noise predictions for smaller aspect ratio jets can be fine-tuned using the appropriate RANS-based mean flow and turbulence properties.

Aircraft↗

NASA NTRS1977

Theory of viscous transonic flow over airfoils at high Reynolds number

This paper considers viscous flows with unseparated turbulent boundary layers over two-dimensional airfoils at transonic speeds. Conventional theoretical methods are based on boundary layer formulations which do not account for the effect of the curved wake and static pressure variations across the boundary layer in the trailing edge region. In this investigation an extended viscous theory is developed that accounts for both effects. The theory is based on a rational analysis of the strong turbulent interaction at airfoil trailing edges. The method of matched asymptotic expansions is employed to develop formal series solutions of the full Reynolds equations in the limit of Reynolds numbers tending to infinity. Procedures are developed for combining the local trailing edge solution with numerical methods for solving the full potential flow and boundary layer equations. Theoretical results indicate that conventional boundary layer methods account for only about 50% of the viscous effect on lift, the remaining contribution arising from wake curvature and normal pressure gradient effects.

Melnik, R. E.↗

NASA NTRS1989

Tropical deforestation and species endangerment - The role of remote sensing

Initial results of a pilot study to link remotely sensed information on tropical forest loss to field-based information on species endangerment are presented. LANDSAT MSS imagery was used to estimate net forest removal, regrowth, and forest edges in Mabira Forest in Uganda during 15-year period. Although four distinct types of closed tropical forest based on structure of dominance could be recognized on the ground, the types could not be distinguished according to differences in spectral reflectance in the MSS bands; yet the closed tropical forest could be readily distinguished from nonforest vegetation types. It is concluded that the utilization of MSS for this purpose is likely to be most successful when combined with larger-scale resolution imagery, such as TM, SPOT, and aerial photography, as well as existing vegetation maps. Of significant promise, however, is the ability to differentiate disturbance regimes, regrowth, and exterior and interior edges of tropical closed forest by the combined use of MSS imagery and ground data.

Westman, Walter E.↗

NASA NTRS2021

Pretest Computational Assessment of Boundary Layer Transition in the NASA Juncture Flow Model with an NACA 0015-Based Wing

The first two phases of the NASA Juncture Flow experiment were carried out on a DLR-F6 swept-wing model and were designed to provide “CFD validation-quality” data toward the assessment and improvement of existing CFD turbulence models in predicting onset and extent of three-dimensional separated flow near the wing-juncture trailing-edge region. The next phase of experiments will involve an NACA 0015-based swept wing, as prior risk reduction experiments had indicated that this wing shape resulted in reduced separation near the juncture region than the DLR-F6 wing, thus providing a better option to evaluate the ability of CFD models to predict incipient turbulent separation. The NACA 0015 measurements will also include IR thermography to infer the variation of transition front with respect to an increasing angle of attack. The primary objective of this work is to computationally make a preliminary assessment of the transition front on both surfaces of the NACA 0015 wing at a crank-chord-based Reynolds number of 2.4 x 106 for four different angles of attack, (0°, 2.5°, 5°, and 7.5°) and to determine the dominant mechanisms responsible for transition. This assessment includes both RANS-based transition models from NASA’s OVERFLOW 2.3b flow solver and linear parabolized stability equations (PSE) stability analysis based on the Langley Stability and Transition Analysis code, LASTRAC. Linear PSE results indicate that the upper surface of the wing is dominated by Tollmien- Schlichting (TS) instabilities, and that the laminar flow region shrinks from about 50% chord to a very small region just downstream of the attachment line as the angle of attack is increased from 0° to 7.5°. Consequently, the transition fronts predicted by the Spalart- Allmaras-based amplification factor transport (AFT-2017b) equation model (which accounts for the TS instabilities alone) and the Menter’s shear-stress transport equation (SST2003)- based Langtry-Menter transition model with ability to account for both TS and crossflow effects (LM2015) compare well with those predicted using linear PSE. On the lower surface of the wing, stationary crossflow (CF) instabilities begin to appear on the inboard portion of the wing in addition to the TS-instabilities for the larger angles of attack (5° and 7.5°), further reducing the laminar flow extent within the inboard region. The LM2015 model that accounts for CF effects is able to replicate this trend but appears to predict a slightly earlier transition. The outcome of this effort will inform the experiment and, when the actual experimental data become available, provide further opportunity to assess and improve the various transition models.

CFD modeling↗

NASA NTRS2005

Noise, Edge Extraction and Visibility of Features

Noise, whether due to the image-gathering device or some other reason, reduces the visibility of fine features in an image. Several techniques attempt to mitigate the impact of noise by performing a low-pass filtering operation on the acquired data. This is based on the assumption that the uncorrelated noise has high-frequency content and thus will be suppressed by low-pass filtering. A result of this operation is that edges in a noisy image also tend to get blurred, and, in some cases, may get completely lost due to the low-pass filtering. In this paper, we quantitatively assess the impact of noise on fine feature visibility by using computer-generated targets of known spatial detail. Additionally, we develop a new scheme for noise-reduction based on the connectivity of edge-features. The overall impact of this scheme is to reduce overall noise, yet retain the high frequency content that make edge-features sharp.

Rahman, Zia-ur↗

NASA NTRS2016

A Model for Jet-Surface Interaction Noise Using Physically Realizable Upstream Turbulence Conditions

This paper is a continuation of previous work in which a generalized Rapid Distortion Theory (RDT) formulation was used to model low-frequency trailing-edge noise. The research was motivated by proposed next-generation aircraft configurations where the exhaust system is tightly integrated with the airframe. Data from recent experiments at NASA on the interaction between high-Reynolds-number subsonic jet flows and an external flat plate showed that the power spectral density (PSD) of the far-field pressure underwent considerable amplification at low frequencies. For example, at the 90deg observation angle, the low-frequency noise could be as much as 10 dB greater than the jet noise itself. In this paper, we present predictions of the noise generated by the interaction of a rectangular jet with the trailing edge of a semi-infinite flat plate. The calculations are based on a formula for the acoustic spectrum of this noise source derived from an exact formal solution of the linearized Euler equations involving (in this case) one arbitrary convected scalar quantity and a Rayleigh equation Green's function. A low-frequency asymptotic approximation for the Green's function based on a two-dimensional mean flow is used in the calculations along with a physically realizable upstream turbulence spectrum, which includes a finite decorrelation region. Numerical predictions of the sound field, based on three-dimensional RANS solutions to determine the mean flow, turbulent kinetic energy and turbulence length and time scales, for a range of subsonic acoustic Mach number jets and nozzle aspect ratios are compared with experimental data. Comparisons of the RANS results with flow data are also presented for selected cases. We find that a finite decorrelation region in the turbulence spectrum increases the low-frequency algebraic decay (the low frequency "roll-off") of the acoustic spectrum with angular frequency thereby producing much closer agreement with noise data for Strouhal numbers less than 0.1. Secondly, the large-aspect-ratio theory is able to predict the low-frequency amplification due to the jet-edge interaction reasonably well, even for moderate aspect ratio nozzles. We show also that the noise predictions for smaller aspect ratio jets can be fine-tuned using the appropriate RANS-based mean flow and turbulence properties.

Jet↗

NASA NTRS2021

Pretest Computational Assessment of Boundary Layer Transition in the NASA Juncture Flow Model with an NACA 0015-Based Wing

The first two phases of the NASA Juncture Flow experiment were carried out on a DLR-F6 swept-wing model and were designed to provide “CFD validation-quality” data toward the assessment and improvement of existing CFD turbulence models in predicting onset and extent of three-dimensional separated flow near the wing-juncture trailing-edge region. The next phase of experiments will involve an NACA 0015-based swept wing, as prior risk reduction experiments had indicated that this wing shape resulted in reduced separation near the juncture region than the DLR-F6 wing, thus providing a better option to evaluate the ability of CFD models to predict incipient turbulent separation. The NACA 0015 measurements will also include IR thermography to infer the variation of transition front with respect to an increasing angle of attack. The primary objective of this work is to computationally make a preliminary assessment of the transition front on both surfaces of the NACA 0015 wing at a crank-chord-based Reynolds number of 2.4 x 106 for four different angles of attack, (0°, 2.5°, 5°, and 7.5°) and to determine the dominant mechanisms responsible for transition. This assessment includes both RANS-based transition models from NASA’s OVERFLOW 2.3b flow solver and linear parabolized stability equations (PSE) stability analysis based on the Langley Stability and Transition Analysis code, LASTRAC. Linear PSE results indicate that the upper surface of the wing is dominated by Tollmien- Schlichting (TS) instabilities, and that the laminar flow region shrinks from about 50% chord to a very small region just downstream of the attachment line as the angle of attack is increased from 0° to 7.5°. Consequently, the transition fronts predicted by the Spalart- Allmaras-based amplification factor transport (AFT-2017b) equation model (which accounts for the TS instabilities alone) and the Menter’s shear-stress transport equation (SST2003)- based Langtry-Menter transition model with ability to account for both TS and crossflow effects (LM2015) compare well with those predicted using linear PSE. On the lower surface of the wing, stationary crossflow (CF) instabilities begin to appear on the inboard portion of the wing in addition to the TS-instabilities for the larger angles of attack (5° and 7.5°), further reducing the laminar flow extent within the inboard region. The LM2015 model that accounts for CF effects is able to replicate this trend but appears to predict a slightly earlier transition. The outcome of this effort will inform the experiment and, when the actual experimental data become available, provide further opportunity to assess and improve the various transition models.

CFD modeling↗

NASA NTRS1972

Vibration and aerodynamic buckling experiments for blunt truncated conical shells with ring-supported edges

The vibration and buckling characteristics of a series of 140 deg ring-supported conical shells have been investigated experimentally and analytically. Experimental results were obtained from 14 conical shells, each attached to a solid nose cap at the small end. The large (base) end was either free or attached to a solid ring of rectangular cross section. The size of the solid base rings of rectangular cross section was systematically varied to provide a wide range of edge restraint. Shell buckling was induced by aerodynamic loading at a Mach number of 3; the vibration data were obtained prior to the wind tunnel tests. The experimental vibration data indicated that the size of the base rings had a pronounced effect on the magnitude of the frequencies and on the frequency spectrum. For vibration modes having less than two circumferential waves, the frequencies descreased with increasing ring size; whereas, for modes with several circumferential waves, the frequencies initially increased rapidly with ring size and then became relatively insensitive to further increases in ring size. This latter behavior was similar to the trend exhibited by the variation of buckling pressure with ring size. The experimental results were in excellent qualitative agreement with theoretical results and indicated that current shell-of-revolution analyses are adequate for predicting the vibration and buckling behavior of ring-supported shells, at least for the simple isotropic shells considered in this investigation.

Miserentino, R.↗

NASA NTRS1979

Improved Woodward's panel method for calculating edge suction forces

A new technique to improve Woodward's (1968) unified subsonic and supersonic panel method is described. The pressure prediction is improved based on a new two-dimensional theory. The method used by Lan (1977) is then used to calculate the leading-edge and side-edge suction forces by direct use of the predicted pressure distribution. The method is applicable to both subsonic and supersonic flow. It is shown that the improved Woodward panel method is capable of accurately predicting leading-edge and side-edge suction forces in subsonic and supersonic flow. Therefore, the method can be used not only to predict the vortex lift of complex planforms through the method of suction analogy, but also to calculate some lateral-directional stability derivatives.

Lan, C. E.↗

DOE OSTI2025

Electron Cyclotron Emission–Based Separatrix Identification in ITER with OMFIT Synthetic Modeling

Accurate determination of the separatrix location is essential for understanding edge plasma behavior and optimizing confinement in tokamaks, especially in next-generation devices such as ITER. In this study, a synthetic microwave diagnostics module was developed and implemented in the OMFIT framework to assess the feasibility of an electron cyclotron emission–based separatrix detection method in ITER plasmas. Simulations were carried out using ITER H-mode equilibrium scenarios with different plasma density profiles and different pedestal widths. Here, the results show that the electron emission temperature profiles consistently exhibit an inversion pattern near the edge, with a well-defined minimum point that could serve as a proxy for the separatrix location. However, unlike in the DIII-D, the minimum point in ITER is systematically offset by approximately 2 cm into the scrape-off layer, independent of density or pedestal width, which is within the radial resolution range (2 to 5 cm) determined by the 500-MHz channel spacing. While the method does not provide the exact separatrix location, it offers a reliable indicator of the boundary region and has potential applications for real-time boundary monitoring in ITER and other future fusion devices.

Electron cyclotron emission↗