Search NASA⌕ Search

SEARCH · Search NASA

Results for “Effective thermal conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Nonlocal effects on thermal transport in hydrodynamic simulations of unmagnetized MagLIF-relevant gaspipes on NIF

We present simulations of heat flow relevant to gaspipe experiments on the National Ignition Facility to investigate kinetic effects on transport phenomena. D 2 and neopentane (C 5 H 12 ) filled targets are used to study the laser preheat stage of a MagLIF scheme where an axial magnetic field is sometimes applied to the target. Simulations were done with the radiation-MHD code HYDRA with a collision-dominated fluid model and the SNB nonlocal electron thermal conduction model. Using the SNB model to evolve the electron temperature increased the heat front propagation of neopentane gas targets compared to a local model by limiting radial heat flow. This increases electron temperature near the axis, which decreases laser absorption. We find that the effect of heat flow models on temperature profiles and laser propagation is modest. Beyond the SNB model, we utilize HYDRA to initialize plasma conditions for the Vlasov–Fokker–Planck K2 code. We run K2 until a quasi-steady state is reached and examine the impact of kinetic effects on heat transport. Although axial heat flow is well predicted by fluid models, the fluid model consistently overpredicts radial heat flow up to 150% in regions with the largest temperature gradient of D 2 filled gaspipes. On the other hand, the SNB nonlocal electron conduction model is found to be adequate for capturing kinetic heat flow in gaspipes.

Lau, Ryan Y. [Univ. of Colorado, Boulder, CO (Unit↗
DOE OSTI2022

Mapping Thermoelectric Transport in a Multicomponent Alloy Space

Abstract Interest in high entropy alloy thermoelectric materials is predicated on achieving ultralow lattice thermal conductivity κ L through large compositional disorder. However, here it is shown that for a given mechanism, such as mass contrast phonon scattering, κ L will be minimized along the binary alloy with highest mass contrast, such that adding an intermediate mass atom to increase atomic disorder can increase thermal conductivity. Only when each component adds an independent scattering mechanism (such as adding strain fluctuation to an existing mass fluctuation) is there a benefit. In addition, both charge carriers and heat‐carrying phonons are known to experience scattering due to alloying effects, leading to a trade‐off in thermoelectric performance. Analytic transport models are applied, based on perturbation and effective medium theories, to predict how alloy scattering will affect the thermal and electronic transport across the full compositional range of several pseudo‐ternary and pseudo‐quaternary alloy systems. To do so, a multicomponent extension is demonstrated to both thermal and electronic binary alloy scattering models based on the virtual crystal approximation. Finally, it is shown that common functional forms used in computational thermodynamics can be applied to this problem to further generalize the scattering behavior that is modeled.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nernst and Ettingshausen effects in gapped quantum materials

Here, we investigate whether there could exist topological invariants of gapped two-dimensional materials related to dissipationless thermoelectric transport at low temperatures. We give both macroscopic and microscopic arguments showing that thermoelectric transport coefficients vanish in the limit of zero temperature, and thus topological invariants arise only from the electric Hall conductance and the thermal Hall conductance. Our arguments apply to systems with arbitrarily strong interactions. We also show that there is no analog of the Thouless pump for entropy.

36 MATERIALS SCIENCE↗
DOE OSTI2019

In situ polymerized succinonitrile-based solid polymer electrolytes for lithium ion batteries

Novel solid polymer electrolytes based on succinonitrile (SN) plastic crystal electrolyte (SN-PCE) and polymerized ionic liquid (PIL) has been successfully synthesized via an in-situ method. The fabricated electrolyte (PIL-SN-PCE) is uniformly inlayed into the supporting matrix of polyimide, which effectively ameliorates the mechanical properties of the electrolyte. PIL can effectively enhance the thermal stability of electrolytes up to 300 °C and mitigate the parasitic reactions between the electrolytes and the electrodes. PIL-SN-PCE exhibits a remarkable oxidation ability up to 5.4 V vs Li/Li + and a high room temperature ionic conductivity of 6.54 × 10 -4 S cm -1 . Furthermore, in-situ formed interface in PIL-SN-PCE guarantee an excellent compatibility with different electrodes, which can effectively improve the cycle stability and rate performances of both half-cells and full cells. Finally, PIL-SN-PCE is considered as a promising electrolyte for high energy density lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

A new ductile, tougher resin for impregnation of superconducting magnets

A major remaining challenge for Nb 3 Sn high field magnets is their training due to random temperature variations in the coils. The main objective of our research is to reduce or eliminate it by finding novel impregnation materials in replacement of the epoxies currently used. An organic olefin-based thermosetting dicyclopentadiene resin, C 10 H 12 , commercially available in Japan as TELENE® by RIMTEC, was used to impregnate a short Nb 3 Sn undulator coil developed by ANL and FNAL. This magnet reached short sample limit after only two quenches, compared with ∼100 when CTD-101K® was used. Ductility, i.e. the ability to accept large strains, and toughness were identified as key properties to achieve these results. In addition, we have been investigating whether mixing TELENE with high heat capacity ceramic powders such as Gd 2 O 3 , Gd 2 O 2 S, and HoCu 2 , increases the specific heat (C p ) of impregnated Nb3Sn superconducting magnets. The viscosity, heat capacity, thermal conductivity, and other physical properties of TELENE with high-C p powder fillers were measured in this study as a function of temperature and magnetic field. The TELENE-87 wt%Gd 2 O 2 S had a peak in C p between 4.3 K and 5.3 K at fields between 0 and 8 T. We have also investigated the effect on the mechanical properties of pure and mixed TELENE under 10 MGy of gamma ray irradiation at the Takasaki Advanced Radiation Research Institute in Takasaki, Japan. TELENE-87 wt%Gd 2 O 2 S exhibited exceptional radiation resistance. Impregnating an undulator coil with TELENE mixed with Gd 2 O 2 S powder will verify whether the coils' thermal stability further improves, or whether its low diffusivity will require engineering the material with high-thermal conductivity components. Short magnet training will lead to better magnet reliability, lower magnet margins, lower risk and substantial saving in accelerators' commissioning costs. Part of this study is supported by the U.S.-Japan Science and Technology Cooperation Program in high energy physics operated by MEXT in Japan and DOE in the U.S.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Nondestructive microstructural investigation of defects in 4H-SiC epilayers using a multiscale luminescence analysis approach

The development of metal oxide semiconductor field effect transistors (MOSFETs) utilizing epitaxially grown 4H-SiC has accelerated in recent years due to their favorable properties, including a high breakdown field, high saturated electron drift velocity, and good thermal conductivity. However, extended defects in epitaxial 4H-SiC can affect both device yields and operational lifetime. In this work, we demonstrate the importance of a multiscale luminescence characterization approach to studying nondestructively extended defects in epitaxial 4H-SiC semiconducting materials. Multiscale luminescence analysis reveals different aspects of excess charge carrier recombination behavior based on the scale of a particular measurement. Combining measurements of the same extended defect area at different scales tells us more about the essential nature of that defect and its microstructure. Here, we use photoluminescence imaging and cathodoluminescence spectrum imaging to investigate the recombination behavior of several different types of extended defects, including stacking faults, inclusions, and basal plane dislocations. A detailed understanding of the optoelectronic properties of extended defects in epitaxial SiC helps elucidate the microstructure of extended defects and can provide pathways to mitigate detrimental changes during device operation related to their evolution, such as the recombination enhanced dislocation glide effect that affects SiC-based MOSFETs.

3C-inclusion↗
DOE OSTI2021

Effect of correlated oxide electrodes on disorder pinning and thermal roughening of ferroelectric domain walls in epitaxial PbZr 0.2 Ti 0.8 O 3 thin films

We report the competing effects of disorder pinning and thermal roughening on ferroelectric domain walls as a function of temperature in epitaxial PbZr 0.2 Ti 0.8 O 3 thin films deposited on (001) SrTiO 3 substrates buffered by three types of correlated oxide electrodes, La 0.67 Sr 0.33 MnO 3 , LaNiO 3 , and SrIrO 3 . Piezo-response force microscopy studies show that the 50 nm PbZr 0.2 Ti 0.8 O 3 films are uniformly polarized in the as-grown states, with the patterned domain structures persisting above 700 °C. For all three types of films, the domain wall roughness is dominated by 2D random bond disorder at room temperature, and transitions to 1D thermal roughening upon heating. The roughness exponent ζ increases progressively from 0.3 to 0.5 within a temperature window that depends on the bottom conducting oxide type, from which we extracted the distribution of disorder pinning energy. Lastly, we discuss the possible origins of the disorder pinning and the effect of the correlated oxide electrodes on the energy landscape of DW motion.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Phonon Thermal Transport in UO 2 via Self-Consistent Perturbation Theory

Computing thermal transport from first-principles in UO 2 is complicated due to the challenges associated with Mott physics. Here, we use irreducible derivative approaches to compute the cubic and quartic phonon interactions in UO 2 from first principles, and we perform enhanced thermal transport computations by evaluating the phonon Green’s function via self-consistent diagrammatic perturbation theory. Our predicted phonon lifetimes at T = 600 K agree well with our inelastic neutron scattering measurements across the entire Brillouin zone, and our thermal conductivity predictions agree well with previous measurements. Finally, both the changes due to thermal expansion and self-consistent contributions are nontrivial at high temperatures, though the effects tend to cancel, and interband transitions yield a substantial contribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermoacoustic Soret separation

In a fluid mixture in a channel with an axial time-averaged temperature gradient, high-amplitude oscillating flow can greatly increase the axial flux of thermal diffusion (Soret) separation of the components of the mixture. The enhancement occurs when the oscillating lateral temperature gradient greatly exceeds the axial gradient, causing a large oscillating concentration that can be favorably time-phased with the oscillating flow. This process can occur even with a negligible pressure oscillation or with a negligible temperature response to pressure, as is the case in most liquid solutions. The thermal boundary condition imposed by realistic solids on thermoacoustic liquids is imperfect, adding mathematical complications that are absent for typical gases, for which the solid surface is temporally isothermal. Compared with gas mixtures, the high Lewis number in typical liquid solutions reduces the separation flux associated with the time-averaged temperature gradient, but it also reduces the remixing associated with the time-averaged mole-fraction gradient. For large enough channels, the second-law separation efficiency is only slightly reduced from that of steady liquid Soret separation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

First-Principles Calculations of Thermoelectric Transport Properties of Quaternary and Ternary Bulk Chalcogenide Crystals

Chalcogenide crystals have a wide range of applications, especially as thermoelectric materials for energy conversion. Thermoelectric materials can be used to generate an electric current from a temperature gradient based on the Seebeck effect and based on the Peltier effect, and they can be used in cooling applications. Using first-principles calculations and semiclassical Boltzmann theory, we have computed the Seebeck coefficient, electrical conductivity, electronic thermal conductivity, power factor, and figure of merit of 30 chalcogenide crystals. A Quantum Espresso package is used to calculate the electronic properties and locate the Fermi level. The transport properties are then calculated using the BoltzTraP code. The 30 crystals are divided into two groups. The first group has four crystals with quaternary composition (A 2 BCQ 4 ) (A = Tl; B = Cd, Hg; C = Si, Ge, Sn; Q = S, Se, Te). The second group contains 26 crystals with the ternary composition (A’B’Q 2 ) (A’ = Ag, Cu, Au, Na; B’ = B, Al, Ga, In; Q = S, Se, Te). Among these 30 chalcogenide crystals, the results for 11 crystals: Tl 2 CdGeSe 4 , Tl 2 CdSnSe 4 , Tl 2 HgSiSe 4 , Tl 2 HgSnS 4 , AuBSe 2 , AuBTe 2 , AuAlTe 2 , AuGaTe 2 , AuInTe 2 , AgAlSe 2 , and AgAlTe 2 are revealed for the first time. In addition, temperature-dependent transport properties of pure and doped AgSbSe 2 and AgSbTe 2 crystals with dopant compositions of AgSb 0.94 Cd 0.06 Te 2 and AgSbTe 1.85 Se 0.15 were explored. These results provide an excellent database for bulk chalcogenides crucial for a wide range of potential applications in renewable energy fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Epitaxial growth of rock salt MgZrN 2 semiconductors on MgO and GaN

Ternary nitride compound semiconductors have attracted recent attention as electronic materials since their properties can be tuned by cation stoichiometry and ordering. A recently discovered example is MgZrN 2 , a ternary analog to the rock salt semiconductor ScN. MgZrN 2 has a larger bandgap and stronger dielectric response than the binary compound. Polycrystalline thin films of MgZrN 2 have been studied, but demonstration of high-quality growth is still required to establish its suitability for technological applications. Here, we report on epitaxial growth of MgZrN 2 thin films on (100) and (111) MgO substrates and (001) GaN templates. The MgZrN 2 composition is confirmed by Rutherford backscattering spectrometry, showing no oxygen in the film except for a thin surface oxide layer. Epitaxial growth results in MgZrN 2 with x-ray diffraction rocking curves with a full-width at half-maximum in the range of 0.3–3.0°, depending on the substrate. Transmission electron microscopy analysis of the MgZrN 2 film grown on a (111) MgO substrate confirms epitaxial growth and shows a sharp film/substrate interface. In-plane temperature-dependent Hall effect measurements show that the material is an n-type semiconductor with a relatively high concentration ( n 300K ≈ 10 19 –10 20 cm -3 ) of thermally activated electrons. Room-temperature transport measurements show a conductivity of 25 S cm -1 and a Seebeck coefficient of -80 μ V K -1 . Overall, these results provide an important step toward integration of rock salt MgZrN 2 with other technological nitrides for device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Impact of Thermal Barrier Coatings on Intake and Exhaust Valves in a Spark Ignition Engine

Spark ignition knock is highly sensitive to changes in intake air temperature. Hot surface temperatures due to ceramic thermal barrier coatings increase knock propensity by elevating the incoming air temperature, thus mitigating the positive impacts of low heat transfer losses by requiring spark retard to avoid knock. Low thermal inertia coatings (i.e. Temperature swing coatings) have been proposed as a means of reducing or eliminating the open cycle charge heating penalty of traditional TBCs through a combination of low thermal conductivity and low volumetric heat capacity materials. However, in order to achieve a meaningful gain in efficiency, a significant fraction of the combustion chamber must be coated. In this study, a coated piston and intake and exhaust valves with coated combustion faces, backsides, and stems are installed in a single-cylinder research engine to evaluate the effect of high coated fractions of the combustion chamber in a knock-sensitive architecture. Spark timing sweeps demonstrated a small, but notable increase in net thermal efficiency compared to the coated piston by itself. Here, a staged valve removal demonstrated that the coated intake valve prevents heat transfer to the incoming air, reducing knock propensity compared to the coated exhaust valve individually.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Experimental Study on the Effect of Localized Blockages on the Friction Factor of a 61-Pin Wire-Wrapped Bundle

Abstract The thermal-hydraulic behavior of the flow in rod bundles has motivated numerous experimental and computational investigations. Previous studies have identified potential for accumulation of debris within the small subchannels of typical wire-wrapped assemblies with subsequent total or partial blockage of subchannel coolant flow. A test campaign was conducted to study the effects of localized blockages on the bundle averaged friction factor of a tightly packed wire-wrapped rod bundle. Blockages were installed within the bundle, and fluid pressure drop was measured across one wire pitch for a Reynolds number range of 500–17,200. The Darcy–Weisbach friction factor of the perturbed rod bundle geometry was compared with that of the unblocked bundle, as well as with the predictions of a well-established friction factor correlation. Differing effects based on blockage size and location for various flow regimes were studied. A number of conclusions can be made about the effects of the blockages on the friction factor, such as an increasing effect of the blockage on friction factor with an increase in Reynolds number, a change in flow behavior in the turbulent transition flow regime near Reynolds number 3000, differences in effect on friction factor for different types of subchannel blockage, and a nonlinear trend in friction factor variation with flow area impeded for edge subchannels. To this end, all data and quantified uncertainty produced in this study are made available for comparison and validation of advanced computational tools.

Engineering↗
DOE OSTI2020

Effect of Off-Stoichiometry on Electrical Conductivity in Ni-Fe and Mn-Co Spinel Systems

This study seeks to clarify the effects of off-stoichiometry on the electrical conductivity of spinels in the (Ni,Fe) 3 O 4 and (Mn,Co) 3 O 4 systems. Spinels with the compositions Ni x Fe 3–x O 4 (where x = 0.85, 0.875, 0.9, 1.0, 1.05, and 1.15) and Mn x Co 3–x O 4 (where x = 1.0, 1.2, 1.35, 1.5, 1.75, and 2.0) were prepared using conventional solid-state process. Electrical conductivity measurements were taken between 500 °C and 800 °C using the 4-point DC method. The conductivity in Ni-Fe spinels increased with increasing Fe content. Similarly, the conductivity of Mn-Co spinels increased drastically with increasing Co content. The coefficients of thermal expansion (CTEs) of these samples were also evaluated. All the (Ni,Fe) 3 O 4 spinels were found to exhibit excellent CTE matching with prospective stack components. However, thermal expansion characteristics were highly dependent on the composition in the (Mn,Co) 3 O 4 system, and only a narrow range of compositions was well-matched in CTE with prospective stack components. The significant effect of cation off-stoichiometry and sample preparation on the electrical behavior of spinels was discussed as a possible explanation for the large discrepancies in reported conductivity values for both systems.

08 HYDROGEN↗
DOE OSTI2021

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5–1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Therefore, based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li 6 PS 5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm -2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg -1 and 675 Wh L -1 , individually.

25 ENERGY STORAGE↗
DOE OSTI2022

Enhancing thermal conductivity and toughness of cellulose nanofibril/boron nitride nanosheet composites

Generally, the thermal conductivity (TC) of composite based on cellulose nanofibrils (CNF) is improved by adding thermal conductive filler, which inevitably leads to the loss of its mechanical properties. Here, in this work, it is the first to simultaneously improve the toughness and TC of CNF/boron nitride nanosheets (BNNS) composite from the perspective of thermal conductive filler addition and CNF crystal change. The hydrophilic-modified BNNSs were successfully prepared by xylose-assisted ball-milling prior to adding into CNF. Compared with that of CNF film (1.34 W/(m·K)), the in-plane TC of CNF/BNNS composite (12.68 W/(m·K)) increased significantly by 846 % with loading 30 % BNNS. Afterwards, both toughness (8.0 MJ·m -3 , increased ~250 %) and TC (14.7 W/(m·K), increased ~16 %) of CNF/BNNS composite were further enhanced significantly by mercerization with 12.5 % NaOH solution. The simultaneously improvement of toughness and TC is unprecedented in related studies, which contributes to the effective preparation of thermal management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Large-scale simulation-based parametric analysis of an optimal precooling strategy for demand flexibility in a commercial office building

Achieving success with grid-interactive efficient buildings (GEBs) is closely tied to the utilization of flexible loads. A valuable strategy involves the implementation of precooling techniques before high-demand events, such as peak hours, by adjusting zone air temperature setpoints. This leads to a reduction in thermal loads and peak electricity demand during these times, as the building’s thermal mass stores and subsequently releases thermal energy. However, the effectiveness of the pre-cooling optimization is highly contingent on specific conditions such as building thermal properties, weather conditions, utility rate structure, HVAC equipment sizing, etc. Therefore, investigating the impacts of these condition-specific factors is crucial, especially when considering precooling strategies that utilize thermal mass in commercial buildings. In this paper, we first devised a novel heuristic control approach that incorporates parameterized optimal precooling thermostat schedules to enhance demand flexibility in a commercial office building. Subsequently, we conducted a thorough performance evaluation of this control strategy. Here, the optimal thermostat schedule was parameterized using three optimization variables: the precooling start time, the precooling end time, and the precooling temperature setpoint. Utilizing the DOE medium-sized office building as the virtual testbed, we showed that the parameterized schedule effectively approximates model predictive control and requires drastically reduced computational overhead. In addition, we investigated the impact of different influencing factors on the optimal precooling strategy. These factors include building thermal mass, outdoor air conditions, and energy price profiles. Using high-performance computing, we simulated a total of 225 scenarios, consisting of three levels of thermal mass, five typical outdoor air temperature profiles, and fifteen time-of-use price plans. The results demonstrate that optimal thermostat scheduling could save substantial energy cost in medium-sized office buildings with heavy thermal mass but with some energy penalty. Although the potential for cost savings is lower in buildings with low and medium thermal mass, the energy penalty remains consistent in all three thermal mass scenarios. The study also highlights the need to account for zone diversity and recognize that a one-size-fits-all-zone setpoint schedule may not be suitable for all zones and can lead to unnecessary energy wastage. Furthermore, the results highlight that while outdoor air conditions play a role in cost and energy performance, the cooling load exerts a more immediate and substantial influence on cost savings in precooling strategies. Although cost savings are comparable under certain conditions with the same cooling load, observed deviations in energy penalty indicate potential disparities in the efficiency of the HVAC system during the load-shifting process. In addition, the duration of peak pricing and the ratio between peak and off-peak times exhibit clear correlations with cost savings and energy consumption, aligning with intuitive expectations. These findings offer valuable insights for optimizing precooling strategies in office buildings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Evaluating the Effects of Transient Purge Flow on Stator-Rotor Seal Performance

Abstract As modern engine designs target higher efficiencies through increased turbine inlet temperatures, critical turbine components are at increased risk of damage from conditions exceeding material melting temperatures. In particular, improperly designed underplatform hardware components are susceptible to damage when hot main gas path flow is ingested into the stator-rotor cavity. While all turbines inherently experience transients during operation, a majority of publicly available turbine studies have been executed using steady operating conditions or inherently transient “blowdown” rigs. For this reason, routine transient events are not well understood. To address this need, the present study utilized a combined experimental and computational approach. The test article is a continuous-duration, one-stage test turbine operating with true-scale engine hardware and seal geometries at engine-representative flow conditions. The nature of the continuous-duration facility uniquely supports the direct assessment of transient events through its ability to transition between steady-state operating conditions. The effects of a transient purge flow were investigated in this study to identify general trends for transient events in a full-scale engine. Results from multiple measurement techniques in the wheelspace region show an interdependence of transient purge flow with a thermal lag of the underplatform hardware. Through experiments conducted at different coolant-to-main gas path temperature ratios, the use of pressure measurements as an indicator of fully purged behavior was introduced, and a thermally driven influence on rim seal performance was quantified. The computational results show good agreement with experimental pressure measurements and provide insight into the physical mechanisms that drive the relationship between pressure and sealing effectiveness measurements observed for the tested geometry.

Engineering↗