Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Some potential blood flow experiments for space

Blood is a colloidal suspension of cells, predominantly erythrocytes, (red cells) in an aqueous solution called plasma. Because the red cells are more dense than the plasma, and because they tend to aggregate, erythrocyte sedimentation can be significant when the shear stresses in flowing blood are small. This behavior, coupled with equipment restrictions, has prevented certain definitive fluid mechanical studies from being performed with blood in ground-based experiments. Among such experiments, which could be satisfactorily performed in a microgravity environment, are the following: (1) studies of blood flow in small tubes, to obtain pressure-flow rate relationships, to determine if increased red cell aggregation can be an aid to blood circulation, and to determine vessel entrance lengths, and (2) studies of blood flow through vessel junctions (bifurcations), to obtain information on cell distribution in downstream vessels of (arterial) bifurcations, and to test flow models of stratified convergent blood flows downstream from (venous) bifurcations.

Cokelet, G. R.↗

Evaluation of fuel injection configurations to control carbon and soot formation in small GT combustors

An experimental program to investigate hardware configurations which attempt to minimize carbon formation and soot production without sacrificing performance in small gas turbine combustors has been conducted at the United Technologies Research Center. Four fuel injectors, embodying either airblast atomization, pressure atomization, or fuel vaporization techniques, were combined with nozzle air swirlers and injector sheaths, and evaluated at test conditions which included and extended beyond standard small gas turbine combustor operation. Extensive testing was accomplished with configurations embodying either a spill return or a T-vaporizer injector. Minimal carbon deposits were observed on the spill return nozzle for tests using either Jet A or ERBS test fuel. A more extensive film of soft carbon was observed on the vaporizer after operation at standard engine conditions, with large carbonaceous growths forming on the device during off-design operation at low combustor inlet temperature. Test results indicated that smoke emission levels depended on the combustor fluid mechanics (especially the mixing rates near the injector), the atomization quality of the injector and the fuel hydrogen content.

Rosfjord, T. J.↗

The electrothermal ramjet

An electrothermal ramjet configuration is examined as a possible alternative to rail guns and mass drivers for high acceleration launch missions. For a specific mission (earth escape) the idealized performance of the electrothermal ramjet, the electrothermal rocket and the electromagnetic acceleration system are compared. This comparison indicates that the gross performance of the ramjet compares favorably with that of the ideal electromagnetic acceleration system. A specific configuration for the ramjet is chosen and models for the dynamics, thermodynamics and fluid mechanics are presented. Results of calculations for a typical supersonic launch cycle suggest that pressure, temperature and power demand profiles associated with ramjet operation should be reasonable. A light gas gun is proposed to accelerate the vehicle to the critical velocity where efficient ramjet operation can begin. The theoretical performance of the ramjet is also shown to be substantially better than that of the light gas gun at high velocities.

Wilbur, P. J.↗

A unique flight test facility - Description and results

The Dryden Flight Research Facility has developed a unique research facility for conducting aerodynamic and fluid mechanics experiments in flight. A low aspect ratio fin, referred to as the flight test fixture (FTF), is mounted on the underside of the fuselage of an F-104G aircraft. The F-104/FTF facility is described, and the capabilities are discussed. The capabilities include (1) a large Mach number envelope (0.4 to 2.0), including the region through Mach 1.0; (2) the potential ability to test articles larger than those that can be tested in wind tunnels; (3) the large chord Reynolds number envelope (greater than 40 million); and (4) the ability to define small increments in friction drag between two test surfaces. Data are presented from experiments that demonstrate some of the capabilities of the FTF, including the shuttle thermal protection system airload tests, instrument development, and base drag studies. Proposed skin friction experiments and instrument evaluation studies are also discussed.

Meyer, R. R., Jr.↗

Fluid dynamic and thermodynamic analysis of a model pertaining to cryogenic fluid management in low gravity environments for a system with dynamically induced settling

The settling behavior of the liquid and gaseous phases of a fluid in a propellant and in a zero-g environment, when such settling is induced through the use of a dynamic device, in this particular case, a helical screw was studied. Particular emphasis was given to: (1) the description of a fluid mechanics model which seems applicable to the system under consideration, (2) a First Law of Thermodynamics analysis of the system, and (3) a discussion of applicable scaling rules.

Rios, J.↗

Thermocapillary flows and their stability: Effects of surface layers and contamination

The fluid mechanics and heat transfer of motions driven by surface tension gradients (Marangoni convection) were analyzed theoretically to obtain an understanding of the convection accompanying the process of growing high quality single crystals from the melt in a mu-g environment. The geometries considered include two dimensional liquid filled slots and axisymmetric float zone configurations.

Davis, S. H.↗

A unique flight test facility: Description and results

The Dryden Flight Research Facility has developed a unique research facility for conducting aerodynamic and fluid mechanics experiments in flight. A low aspect ratio fin, referred to as the flight test fixture (FTF), is mounted on the underside of the fuselage of an F-104G aircraft. The F-104G/FTF facility is described, and the capabilities are discussed. The capabilities include (1) a large Mach number envelope (0.4 to 2.0), including the region through Mach 1.0; (2) the potential ability to test articles larger than those that can be tested in wind tunnels; (3) the large chord Reynolds number envelope (greater than 40 million); and (4) the ability to define small increments in friction drag between two test surfaces. Data are presented from experiments that demonstrate some of the capabilities of the FTF, including the shuttle thermal protection system airload tests, instrument development, and base drag studies. Proposed skin friction experiments and instrument evaluation studies are also discussed.

Meyer, R. R., Jr.↗

An investigation of equilibrium concepts

A different approach to modeling of the thermochemistry of rocket engine combustion phenomena is presented. The methodology described is based on the hypothesis of a new variational principle applicable to compressible fluid mechanics. This hypothesis is extended to treat the thermochemical behavior of a reacting (equilibrium) gas in an open system.

Prozan, R. J.↗

Opportunities for research in aerothermodynamics

"Aerothermodynamics' involves the disciplines of chemistry, thermodynamics, fluid mechanics and heat transfer which have collaborative importance in propulsion systems. There are growing opportunities for the further application of these disciplines to improve the methodology for the design of advanced gas turbines; particularly, the combustor and turbine. Design procedures follow empirical or cut and try guidelines. The tremendous advances in computational analysis and in instrumentation techniques hold promise for research answers to complex physical processes that are currently not well understood. The transfer of basic research understanding to engineering design should result in shorter, less expensive development commitments for engines. The status and anticipated opportunities in research topics relevant to combustors and turbines is reviewed.

Graham, R. W.↗

On issues concerning flow separation and vortical flows in 3 dimensions

This review provides an illustrated introduction laying the knowledge base for vortical flows about three dimensional configurations that are of typical interest to aerodynamicists and researchers in fluid mechanics. The paper then compiles a list of ten issues, again in illustrative format, that the authors deem important to the understanding of complex vortical flows. These issues and our responses to them provide, it is hoped, a skeletal framework on which to hang the ensuing conference proceedings.

Peake, D. J.↗

Velocity Visualization in Gaseous Flows

Techniques yielding simultaneous, multiple point measurements of velocity in reacting or nonreacting flow fields have the potential to significantly impact basic and applied studies of fluid mechanics. Several candidate schemes which could provide such measurement capability were investigated. The concepts utilize laser sources which lead to scattered light which can be monitored by a film based camera or a multielement solid state camera. Velocity measurements in supersonic flows using a novel Doppler modulated fluorescence concept are presented.

Hanson, R. K.↗

Major disruptions, inverse cascades, and the Strauss equations

Current-carrying plasmas in a strong d.c. magnetic field are subject to violent disruptions above certain thresholds. At present difficult to verify, explanations are typically sought in terms of 'tearing modes'. An alternative explanation is in terms of inverse magnetic helicity cascades, generated from a variety of possible sources of small-scale MHD turbulence. Strongly anisotropic MHD plasmas may be described by the Strauss equations. Indications of turbulent inverse cascade behavior for the Strauss equations are sought, in parallel with earlier examples from MHD and fluid mechanics.

Montgomery, D.↗

Experimental and theoretical study of combustion jet ignition

A combustion jet ignition system was developed to generate turbulent jets of combustion products containing free radicals and to discharge them as ignition sources into a combustible medium. In order to understand the ignition and the inflammation processes caused by combustion jets, the studies of the fluid mechanical properties of turbulent jets with and without combustion were conducted theoretically and experimentally. Experiments using a specially designed igniter, with a prechamber to build up and control the stagnation pressure upstream of the orifice, were conducted to investigate the formation processes of turbulent jets of combustion products. The penetration speed of combustion jets has been found to be constant initially and then decreases monotonically as turbulent jets of combustion products travel closer to the wall. This initial penetration speed to combustion jets is proportional to the initial stagnation pressure upstream of the orifice for the same stoichiometric mixture. Computer simulations by Chorin's Random Vortex Method implemented with the flame propagation algorithm for the theoretical model of turbulent jets with and without combustion were performed to study the turbulent jet flow field. In the formation processes of the turbulent jets, the large-scale eddy structure of turbulence, the so-called coherent structure, dominates the entrainment and mixing processes. The large-scale eddy structure of turbulent jets in this study is constructed by a series of vortex pairs, which are organized in the form of a staggered array of vortex clouds generating local recirculation flow patterns.

Chen, D. Y.↗

Control of the forebody vortex orientation by asymmetric air injection. Part A: Application to enhance departure/spin recovery of fighter aircraft and Part B: Details of the flow structure

A concept developed to provide powerful directional control effectiveness for a fighter aircraft at high angles of attack is described. The concept utilizes the energy concentrated in the strong forebody vortices (which form on slender bodies of high relative incidence) by controlling the lateral orientation of the vortices with respect to the body. The objective was to utilize the side force associated with asymmetric vortices, in a controlled manner, to enhance the ability of the fighter to recover from a departure from controlled flight. The results from water tunnel and wind tunnel experiments show that a small amount of tangential blowing along the forebody near the apex can effectively alter the forebody vortex system and generate large restoring yawing moments. Six degree of freedom digital simulation results show that this concept can substantially enhance recovery characteristics of fighter aircraft with long, slender forebodies. Also, the results of experiments which were conducted on a cone model are discussed where the principal test objective was to develop an understanding of the fluid mechanics involved in the process of vortex control. Knowledge gained in these more generic tests should allow the concept to be applied to a wider range of configurations.

Skow, A. M.↗

Thermocapillary flows and their stability: Effects of surface layers and combination

The theoretical analysis of the fluid mechanics and heat transfer of motions driven by surface tension gradients (Marangoni convection) was researched. Convection accompanying the process of growing high quality single crystals from the melt in a micro-g environment was examined. The geometries considered include two dimensional liquid filled slots and axisymmetric float-zone configurations.

Davis, S. H.↗

Velocity visualization in gaseous flows

Techniques yielding simultaneous, multiple-point measurements of velocity in reacting or nonreacting flow fields have the potential to significantly impact basic and applied studies of fluid mechanics. This research program is aimed at investigating several candidate schemes which could provide such measurement capability. The concepts under study have in common the use of a laser source (to illuminate a column, a grid, a plane or a volume in the flow) and the collection of light at right angles (from Mie scattering, fluorescence, phosphorescence or chemiluminescence) using a multi-element solid-state camera (100 x 100 array of photodiodes). The work will include an overview and a status report of work in progress with particular emphasis on the method of Doppler-modulated absorption.

Hanson, R. K.↗

Vortex generating flow passage design for increased film-cooling effectiveness and surface coverage

The fluid mechanics of the basic discrete hole film cooling process is described as an inclined jet in crossflow and a cusp shaped coolant flow channel contour that increases the efficiency of the film cooling process is hypothesized. The design concept requires the channel to generate a counter rotating vortex pair secondary flow within the jet stream by virture of flow passage geometry. The interaction of the vortex structures generated by both geometry and crossflow was examined in terms of film cooling effectiveness and surface coverage. Comparative data obtained with this vortex generating coolant passage showed up to factors of four increases in both effectiveness and surface coverage over that obtained with a standard round cross section flow passage. A streakline flow visualization technique was used to support the concept of the counter rotating vortex pair generating capability of the flow passage design.

Papell, S. S.↗