Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Automated Detection of Instability-Inducing Channel Geometry Transitions in Saint-Venant Simulation of Large-Scale River Networks

A new sweep-search algorithm (SSA) is developed and tested to identify the channel geometry transitions responsible for numerical convergence failure in a Saint-Venant equation (SVE) simulation of a large-scale open-channel network. Numerical instabilities are known to occur at “sharp” transitions in discrete geometry, but the identification of problem locations has been a matter of modeler’s art and a roadblock to implementing large-scale SVE simulations. The new method implements techniques from graph theory applied to a steady-state 1D shallow-water equation solver to recursively examine the numerical stability of each flowpath through the channel network. The SSA is validated with a short river reach and tested by the simulation of ten complete river systems of the Texas–Gulf Coast region by using the extreme hydrological conditions recorded during hurricane Harvey. The SSA successfully identified the problematic channel sections in all tested river systems. Subsequent modification of the problem sections allowed stable solution by an unsteady SVE numerical solver. The new SSA approach permits automated and consistent identification of problem channel geometry in large open-channel network data sets, which is necessary to effectively apply the fully dynamic Saint-Venant equations to large-scale river networks or for city-wide stormwater networks.

54 ENVIRONMENTAL SCIENCES↗

GEOMETRY-INDEPENDENT DETERMINATION OF RADIAL DENSITY DISTRIBUTIONS IN MOLECULAR CLOUD CORES AND OTHER ASTRONOMICAL OBJECTS

We present a geometry-independent method for determining the shapes of radial volume density profiles of astronomical objects whose geometries are unknown, based on a single column density map. Such profiles are often critical to understand the physics and chemistry of molecular cloud cores, in which star formation takes place. The method presented here does not assume any geometry for the object being studied, thus removing a significant source of bias. Instead, it exploits contour self-similarity in column density maps, which appears to be common in data for astronomical objects. Our method may be applied to many types of astronomical objects and observable quantities so long as they satisfy a limited set of conditions, which we describe in detail. We derive the method analytically, test it numerically, and illustrate its utility using 2MASS-derived dust extinction in molecular cloud cores. While not having made an extensive comparison of different density profiles, we find that the overall radial density distribution within molecular cloud cores is adequately described by an attenuated power law.

79 ASTRONOMY AND ASTROPHYSICS↗

RESOLVING THE GEOMETRY OF THE INNERMOST RELATIVISTIC JETS IN ACTIVE GALACTIC NUCLEI

In the current paradigm, it is believed that the compact VLBI radio core of radio-loud active galactic nuclei (AGNs) represents the innermost upstream regions of relativistic outflows. These regions of AGN jets have generally been modeled by a conical outflow with a roughly constant opening angle and flow speed. Nonetheless, some works suggest that a parabolic geometry would be more appropriate to fit the high energy spectral distribution properties and it has been recently found that, at least in some nearby radio galaxies, the geometry of the innermost regions of the jet is parabolic. We compile here multi-frequency core sizes of archival data to investigate the typically unresolved upstream regions of the jet geometry of a sample of 56 radio-loud AGNs. Data combined from the sources considered here are not consistent with the classic picture of a conical jet starting in the vicinity of the super-massive black hole (SMBH), and may exclude a pure parabolic outflow solution, but rather suggest an intermediate solution with quasi-parabolic streams, which are frequently seen in numerical simulations. Inspection of the large opening angles near the SMBH and the range of the Lorentz factors derived from our results support our analyses. Our result suggests that the conical jet paradigm in AGNs needs to be re-examined by millimeter/sub-millimeter VLBI observations.

79 ASTRONOMY AND ASTROPHYSICS↗

Spacecraft Geometry Effects on Kinetic Impactor Missions

Abstract The DART (Double Asteroid Redirection Test) mission will impact a spacecraft on the secondary (Dimorphos) of the binary asteroid system Didymos in 2022 September, with the goal of altering the orbital period of Dimorphos about Didymos sufficiently to be observed from ground-based observations. Numerical impact modeling is a crucial component in understanding the outcome of the DART experiment, and while many have investigated the effects of target properties, such as material strength and porosity (which remain unknown), an often overlooked factor is the importance of accurately representing the spacecraft itself in such models. Most impact modeling to date has considered simple impactor geometries such as a solid uniform sphere, but in reality the spacecraft is a complex shape full of different components, open spaces, and thin walled structures. At a minimum, a simple solid representation underestimates the surface area of the impact: for a small body such as Dimorphos (approximately 160 m in diameter), the difference between a spacecraft spanning 20 m (including solar arrays) impacting and a sub-1 m idealized shape may be important. In this paper, we compare models impacting high-fidelity models of the spacecraft based on the CAD geometry with various simplified impactors, in order to assess the potential importance of this effect. We find that the difference between the simplest impactor geometries (such as a uniform sphere) and the real spacecraft is measurable, and has an interesting dependence on the material properties of the asteroid itself.

36 MATERIALS SCIENCE↗

Effect of trailing edge geometry and thickness on the performance of certain turbine stator blading

The experimental and analytical investigation included solid blades with five different trailing-edge thicknesses and four different trailing-edge geometries. One of the geometries was round, one was square, one was tapered from the suction surface, and the other tapered from the pressure surface. One of the trailing-edge thicknesses was sharp edged; the other four thicknesses were equivalent to about 5, 11, 16, and 20 percent of the blade throat width. The experimental results show increased efficiency loss for increased trailing-edge thickness for all trailing-edge geometries. The blade with round trailing edge, equal to about 11 percent of the blade throat width, had 60 percent more loss than the sharp-edged blade. For the same trailing-edge thickness, square trailing edges caused more loss than round trailing edges, and the tapered trailing edges caused about the same loss as the round trailing edges.

Prust, H. W., Jr.↗

Experimental investigation of model variable-geometry and ogee tip rotors.

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that several variable-geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance.

Landgrebe, A. J.↗

Design of various fixed-geometry water-lubricated hydrodynamic journal bearings for maximum stability

This publication is the result of over 260 fractional-frequency-whirl stability tests on a variety of fixed-geometry journal bearings. It is intended principally as a guide in the selection and design of antiwhirl bearings that must operate at high speeds and low loads in low-viscosity fluids such as water or liquid metals. However, the various fixed-geometry configurations can be employed as well in applications where other lubricants, such as oil, are used and fractional-frequency whirl is a problem. The important parameters that effect stability are discussed for each bearing type, and design curves to facilitate the design of optimum-geometry bearings are included. A comparison of the stability of the different bearing configurations tested is also given.

Schuller, F. T.↗

Experimental investigation of model variable-geometry and ogee tip rotors

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a model rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that properly selected variable geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance. Axial spacing of alternate blades was found to provide the greatest performance benefit, and further improvements were achieved by combining azimuth spacing with axial spacing. The performance benefit appears to be related to the relief of local adverse aerodynamic phenomena produced by vortex interference. The ogee tip design was found to substantially reduce the concentrated core intensity of the tip vortex, and could thus prove beneficial for the relief of blade-vortex interaction problems. However, the ogee tip was found to reduce hover performance at model scale.

Landgrebe, A. J.↗

Ground idle performance improvement of a double-annular combustor by using simulated variable combustor geometry

A test program was undertaken to determine if variable combustor geometry could be used to reduce exhaust emissions of a low-pressure-ratio jet engine operating at ground idle conditions. Three techniques for varying combustor geometry were simulated. Other techniques evaluated were radial fuel staging and the use of preheated fuel. When simulated variable combustor geometry was employed with radial fuel staging, combustion efficiency at a fuel-air ratio of 0.01 was increased from 77 to 95 percent, and exhaust emissions of unburned hydrocarbons and carbon monoxide were significantly reduced.

Schultz, D. F.↗

Low speed wind tunnel investigation of the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries

A series of tests was conducted to determine the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries. The effects of inlet lip shape and diffuser length were also investigated. The tests were conducted in a low-speed wind tunnel at free-stream velocities of 0 and 45 meters per second. Inlet incidence angle was varied from 0 deg to 50 deg. The inlets were sized to fit a 13.97-centimeter-diameter fan. In terms of the highest level of inlet total pressure recovery for a given amount of noise suppression, a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry provided the best results over all conditions of free-stream velocity and incidence angle. Increasing inlet lip contraction ratio extended the maximum incidence angle for attached lip flow, while increasing inlet diffuser length resulted in a higher total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗

Nozzle and wing geometry effects on OTW aerodynamic characteristics

The effects of nozzle geometry and wing size on the aerodynamic performance of several 5:1 aspect ratio slot nozzles are presented for over-the-wing (OTW) configurations. Nozzle geometry variables include roof angle, sidewall cutback, and nozzle chordwise location. Wing variables include chord size, and flap deflection. Several external deflectors also were included for comparison. The data indicate that good flow turning may not necessarily provide the best aerodynamic performance. The results suggest that a variable exhaust nozzle geometry offers the best solution for a viable OTW configuration.

Vonglahn, U.↗

Nozzle and wing geometry effects on OTW aerodynamic characteristics

The effects of nozzle geometry and wing size on the aerodynamic performance of several 5:1 aspect ratio slot nozzles are presented for OTW configurations. Nozzle geometry variables include roof angle, sidewall cutback, and nozzle chordwise location. Wing variables include chord size, and flap deflection. Several external deflectors also were included for comparison. The data indicate that good flow turning may not necessarily provide the best aerodynamic performance. The results of the study suggest that a variable exhaust nozzle geometry offers the best solution for a viable OTW configuration.

Von Glahn, U.↗

OTW noise correlation for several nozzle/wing geometries using a 5:1 slot nozzle with external deflectors

Acoustic spectral data obtained from a model-scale study of several over the wing (OTW) configurations with a 5:1 slot nozzle using various external deflectors are correlated in terms of deflector geometry and flow parameters. Variations in the deflector geometry include deflector size and deflector angle. In addition, geometry variations in flap setting and nozzle chordwise location are included. Three dominant noise sources are correlated: fluctuating lift noise, flap trailing edge noise, and jet mixing noise. Aerodynamic characteristics including lift and thrust measurements, obtained for the various configurations are summarized.

Vonglahn, U. H.↗

OTW noise correlation for several nozzle/wing geometries using a 5:1 slot nozzle with external deflectors

Acoustic spectral data obtained from a model-scale study of several OTW configurations with a 5:1 slot nozzle using various external deflectors are correlated in terms of deflector geometry and flow parameters. Variations in the deflector geometry include deflector size and deflector angle. In addition, geometry variations in flap setting and nozzle chordwise location are included. Three dominant noise sources are correlated: fluctuating lift noise, flap trailing edge noise, and jet mixing noise. Aerodynamic characteristics, including lift and thrust measurements, obtained for the various configurations are summarized.

Von Glahn, U.↗

GEMPAK: An arbitrary aircraft geometry generator

A computer program, GEMPAK, has been developed to aid in the generation of detailed configuration geometry. The program was written to allow the user as much flexibility as possible in his choices of configurations and the detail of description desired and at the same time keep input requirements and program turnaround and cost to a minimum. The program consists of routines that generate fuselage and planar-surface (winglike) geometry and a routine that will determine the true intersection of all components with the fuselage. This paper describes the methods by which the various geometries are generated and provides input description with sample input and output. Also included are descriptions of the primary program variables and functions performed by the various routines. The FORTRAN program GEMPAK has been used extensively in conjunction with interfaces to several aerodynamic and plotting computer programs and has proven to be an effective aid in the preliminary design phase of aircraft configurations.

Stack, S. H.↗

A geometry package for generation of input data for a three-dimensional potential-flow program

The preparation of geometric data for input to three-dimensional potential flow programs was automated and simplified by a geometry package incorporated into the NASA Langley version of the 3-D lifting potential flow program. Input to the computer program for the geometry package consists of a very sparse set of coordinate data, often with an order of magnitude of fewer points than required for the actual potential flow calculations. Isolated components, such as wings, fuselages, etc. are paneled automatically, using one of several possible element distribution algorithms. Curves of intersection between components are calculated, using a hybrid curve-fit/surface-fit approach. Intersecting components are repaneled so that adjacent elements on either side of the intersection curves line up in a satisfactory manner for the potential-flow calculations. Many cases may be run completely (from input, through the geometry package, and through the flow calculations) without interruption. Use of the package significantly reduces the time and expense involved in making three-dimensional potential flow calculations.

Halsey, N. D.↗

Dayside merging and cusp geometry

Geometrical considerations are presented to show that dayside magnetic merging when constrained to act only where the fields are antiparallel results in lines of merging that converge at the polar cusps. An important consequence of this geometry is that no accelerated flows are predicted across the dayside magnetopause. Acceleration owing to merging acts in opposition to the magnetosheath flow at the merging point and produces the variably directed, slower-than-magnetosheath flows observed in the entry layer. Another consequence of the merging geometry is that much of the time closed field lines constitute the subsolar region of the magnetopause. The manner in which the polar cap convection patterns predicted by the proposed geometry change as the interplanetary field is rotated through 360 deg provides a unifying description of how the observed single circular vortex and the crescent-shaped double vortex patterns mutually evolve under the influence of a single operating principle.

Crooker, N. U.↗

The grabens of Canyonlands National Park, Utah - Geometry, mechanics, and kinematics

Results are reported for three years of field and analytical study of a system of young and very well exposed grabens in southeastern Utah. A kinematic and mechanical model is developed for these specific grabens with the hope that this will aid in interpreting graben systems elsewhere on the earth and other planets. Because studies on other planets must be based entirely on photo analysis, an attempt is made to determine to what extent three-dimensional geometry could be inferred from photographs alone. An equation based on the model of graben geometry and kinematics relates thickness of faulted plates to graben parameters measurable on photographs. The initial width of a nascent graben is a simple function of the dip of the faults bounding the graben and of the thickness of the faulted brittle plate. The uniform spacing of the grabens is a natural result of the geometry of the system.

Mcgill, G. E.↗