Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hybrid Energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A hybrid porous model for full reactor core scale CFD investigation of a prismatic HTGR

Three-dimensional (3-D) Computational Fluid Dynamics (CFD) analysis of a whole nuclear reactor core is a tremendous challenge due to the large geometric volume and complex structures. Here, this research presents a hybrid porous (HP) model to simplify a prismatic High Temperature Gas-cooled Reactor (HTGR) core, so 3-D CFD investigation can be performed on a full reactor core scale. In the HP model, the prototypic small coolant channels in the nuclear fuel blocks are lumped together to form multiple equivalent large coolant channels, and then the porous medium flow model is applied to each of them. Therefore, heat transfer in fuel blocks is computed by a hybrid combination of solid energy and porous flow energy equations. The similarity between the HP model and prototypic model is achieved by deriving the porous flow permeability, inertial resistance factor, and artificial thermophysical properties. Compared with the widely used whole porous (WP) flow model, the HP model preserves more realistic geometric structures, and therefore more accurate physical processes. The General Atomics' Modular High Temperature Gas-cooled Reactor (MHTGR) design was chosen as a prototype to demonstrate the methodology. Simulations were performed using the prototypic CFD model and HP model at steady-state forced circulation, steady-state natural circulation, and transient conditions that correspond to normal operation, extended period of pressurized cool down, and short-term transients after reactor shutdown, respectively. The comparison shows good agreement between the HP model and prototypic model in the maximum fuel temperature, average solid temperature, and helium flow rate, which demonstrates the potential applicability of the HP model for a full reactor core scale simulation in the future. As a benefit, the HP model reduces the mesh quantity by a factor of 50 from a prototypic model. Correspondingly, the computation time was reduced by a factor of at least 30.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Substitution or Shared Utilization? Intrahousehold Vehicle Use in Mixed-Powertrain Households

While previous research has focused heavily on understanding the factors deriving alternative fuel vehicle adoption rates, there remains a significant gap in understanding how households distribute mileage across different powertrains. This study utilizes data from the 2022 Next Generation National Household Travel Survey to investigate vehicle miles traveled within a sample of 150 plug-in electric vehicle (PEV)-owning households (in which at least one battery electric vehicle is present), characterizing how different powertrains are integrated into daily mobility. Leveraging a Seemingly Unrelated Regression (SUR) framework the study jointly models the utilization of PEVs, hybrid electric vehicles (HEV), and internal combustion engine vehicles (ICEVs) while accounting for household-level substitution effects. The results provide evidence of an asymmetric substitution effect. In households with mixed-powertrain configurations, the ICEV captures a substantially higher share of household miles (compared with the PEV), acting as a utility sponge. Conversely, the model identifies specific socioeconomic and geographic cohorts that prioritize PEV as the primary household workhorse, indicating a systematic sorting effect. Although the sample size limits broader generalizability, these findings suggest that PEVs are used for frequent, specific routine-intensive roles, whereas the ICEV remains a specialized utility vehicle. These insights highlight distinct intrahousehold vehicle use behaviors that are often obscured by aggregate fleetwide statistics.

25 ENERGY STORAGE↗
DOE OSTI2024

Coaxial color channel focus evaluation to estimate standoff height in directed energy deposition additive manufacturing

Directed energy deposition (DED) is an additive manufacturing process that is being rapidly adopted by industry and is well suited for the fabrication of complex components in a variety of metal alloys. In laser cladding systems such as DED, powder is blown in a stream to a metal substrate coincident with a laser necessary to deposit molten metal with 3D spatial control. The focus of both the laser and the powder stream are crucial, and best deposition occurs at a predetermined standoff height between the build surface and the print head. Generally, no monitoring of this distance is implemented in commercial DED systems. Due to potential over or under building, the standoff height often changes over time but tends to self-correct. However, inexpensive and minimally intrusive methods to identify optimal standoff are required to provide real-time control to maintain the optimal distance. The present work explores the quantification of the focus of the three-color channels of a coaxial camera to determine the standoff height. An experiment was performed in which a 254 mm wall is built and the standoff height, initially 5.0 mm below the optimal position, was then intentionally increased every 25.4 mm of wall length by an amount of 1.0 mm to a final position 7.0 mm above optimal. Computer vision is demonstrated to monitor the amount of focus in each color band and estimate standoff distance. Finally, a response can be calculated in under 40 ms using simple hardware and can work in most laser-based DED systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Free‐Standing α‐MoO 3 / Ti 3 C 2 MXene Hybrid Electrode in Water‐in‐Salt Electrolytes

While transition‐metal oxides such as α‐MoO 3 provide high capacity, their use is limited by modest electronic conductivity and electrochemical instability in aqueous electrolytes. Two‐dimensional (2D) MXenes, offer metallic conductivity, but their capacitance is limited in aqueous electrolytes. Insertion of partially solvated cations into Ti 3 C 2 MXene from lithium‐based water‐in‐salt (WIS) electrolytes enables charge storage at positive potentials, allowing a wider potential window and higher capacitance. Herein, we demonstrate that α‐MoO 3 /Ti 3 C 2 hybrids combine the high capacity of α‐MoO 3 and conductivity of Ti 3 C 2 in WIS (19.8 m LiCl) electrolyte in a wide 1.8 V voltage window. Cyclic voltammograms reveal multiple redox peaks from α‐MoO 3 in addition to the well‐separated peaks of Ti 3 C 2 in the hybrid electrode. This leads to a higher specific charge and a higher rate capability compared to a carbon and binder containing α‐MoO 3 electrode. These results demonstrate that the addition of MXene to less conductive oxides eliminates the need for conductive carbon additives and binders, leads to a larger amount of charge stored, and increases redox capacity at higher rates. In addition, MXene encapsulated α‐MoO 3 showed improved electrochemical stability, which was attributed to the suppressed dissolution of α‐MoO 3 . The work suggests that oxide/MXene hybrids are promising for energy storage.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Build plate conduction cooling for thermal management of wire arc additive manufactured components

Wire arc additive manufacturing (WAAM) allows for quick, large component manufacturing with fast deposition rates while leveraging readily available wire feedstock that is significantly cheaper than metal powder. However, the increased deposition rate of this process requires enhanced thermal management as failures can occur due to overheating. A common strategy to mitigate overheating is to dwell, or pause, between individual layers; however, this can significantly increase build times and eliminate the advantage of additive manufacturing being able to manufacture components quickly. To help mitigate this issue, this study explores the use of active cooling to maintain process control and to decrease overall build time. In this work, conductive cooling applied to either the bottom or side of the print substrate was explored. Results from this study showed that bottom build plate active cooling can be used to decrease dwell times by up to 50% and decrease cool-down to room temperature after the building process by up to 75%. Results from this study demonstrate that the use of active cooling strategies for WAAM can be used for better thermal control over the process and should be further investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Skinny kelp (Saccharina angustissima) provides valuable genetics for the biomass improvement of farmed sugar kelp (Saccharina latissima)

Abstract Saccharina latissima (sugar kelp) is one of the most widely cultivated brown marine macroalgae species in the North Atlantic and the eastern North Pacific Oceans. To meet the expanding demands of the sugar kelp mariculture industry, selecting and breeding sugar kelp that is best suited to offshore farm environments is becoming necessary. To that end, a multi-year, multi-institutional breeding program was established by the U.S. Department of Energy's (DOE) Advanced Research Projects Agency-Energy (ARPA-E) Macroalgae Research Inspiring Novel Energy Resources (MARINER) program. Hybrid sporophytes were generated using 203 unique gametophyte cultures derived from wild-collected Saccharina spp . for two seasons of farm trials (2019–2020 and 2020–2021). The wild sporophytes were collected from 10 different locations within the Gulf of Maine (USA) region, including both sugar kelp ( Saccharina latissima ) and the skinny kelp species ( Saccharina angustissima ). We harvested 232 common farm plots during these two seasons with available data. We found that farmed kelp plots with skinny kelp as parents had an average increased yield over the mean (wet weight 2.48 ± 0.90 kg m −1 and dry weight 0.32 ± 0.10 kg m −1 ) in both growing seasons. We also found that blade length positively correlated with biomass in skinny kelp x sugar kelp crosses or pure sugar kelp crosses. The skinny x sugar progenies had significantly longer and narrower blades than the pure sugar kelp progenies in both seasons. Overall, these findings suggest that sugar x skinny kelp crosses provide improved yield compared to pure sugar kelp crosses.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Impact of lead on an axisymmetric, single bead blown powder DED overhung geometry

Metal additive manufacturing can be utilized for the near net-shape manufacture of components in a layer wise technique. Traditionally, the buildup process is conducted in the direction of gravity or bottom to top in the vertical orientation; however, with the availability of commercial systems with additive heads or fixturing that can index from vertical, and the need to manufacture larger parts without modifying available systems, the limitation of manufacturing from bottom to top is removed enabling the buildup of larger components printed at an angle from vertical. The effect of gravity on the melt pool and as-deposited component quality when printing off vertical is unknown in literature, especially for axisymmetric components. This understanding is critical for the advancement of manufacturing components of increased size in 4 and 5-axis additive systems. This investigation utilizes blown powder directed energy deposition to evaluate the change in as-printed geometry when the start point is altered in relation to gravity while the part rotates to manufacture an axisymmetric component. The objectives of this work are to determine the impact of the deposition location on the geometric variability on axisymmetric components. This investigation tests the hypothesis that differences in layer height exist due to a change in catchment efficiency when the deposition location is moved to a tangent of the round geometry due to a change in the melt pool dynamics. It was found the ideal deposition location when printing at 26.6-degrees from vertical was at −90-degrees from the top center point of the component, along the tangent, where gravity was pushing the melt pool down, but the rotation of the part was pulling the deposited material towards the top center of the component. This work provides an understanding of layer height stability and catchment efficiency to guide print orientation strategy for high-aspect ratio components. It was found the −90-degree lead deposition had the best layer height stability at 0.6 % as compared to the top-center at 6.3 % and +90-degree deposition location at 9.2 % for the nominal programmed layer height. The change in layer height also effected the final diameter the greatest for the top center deposition location where the diameter diverged by 2.5 % during the overbuild condition and converged by 0.6 %. In conclusion, this finding will increase the manufacturing efficiency of axisymmetric components by increasing the passive stability of the printing process for the successful manufacture of parts without the need for perfectly calibrated manufacturing parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Physics-informed CoKriging model of a redox flow battery

Vanadium redox flow batteries (VRFBs) offer the capability to store large amounts of energy cheaply and efficiently, however, there is a need for fast and accurate models of the charge–discharge curve of a VRFB to potentially improve the battery capacity and performance. Here, we develop a multifidelity model for predicting the charge–discharge curve of a VRFB. In the multifidelity model, we use the Physics-informed CoKriging (CoPhIK) machine learning method that is trained on experimental data and constrained by the so-called “zero-dimensional” physics-based model. Here we demonstrate that the model shows good agreement with experimental results and significant improvements over existing zero-dimensional models. We show that the proposed model is robust as it is not sensitive to the input parameters in the zero-dimensional model. We also show that only a small amount of high-fidelity experimental datasets are needed for accurate predictions for the range of considered input parameters, which include current density, flow rate, and initial concentrations.

25 ENERGY STORAGE↗
DOE OSTI2023

Additive manufacturing as a processing route for steel-aluminum bimetallic structures

Here we present results on the fabrication of steel-aluminum bi-metallic structures using directed energy deposition additive manufacturing. The challenges associated with the fabrication of a sharp transition from steel to aluminum are uncovered using ex-situ characterization techniques and thermo-mechanical modeling of the deposition process. It was found that the fabrication of a sharp steel-aluminum transition is challenging with extensive cracking observed at the interface. The cracking was attributed to the combined effect of residual stress development due to thermal expansion coefficient mismatch and the presence of ordered intermetallics with low ductility at the interface. Using a coupled thermodynamic and thermo-mechanical modeling approach, potential pathways to enable the fabrication of steel-aluminum bi-metallic structures using additive manufacturing are proposed. The results presented here can lay the foundation for future work on the fabrication of bi-metallic steel-aluminum structures using directed energy deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Unit cell manufacture by blown powder directed energy deposition

Lattice structures manufactured by additive manufacturing show unique promise to alter existing components to improve the thermo-mechanical properties of the base structure. Here, in the present study, the manufacture of a self-supporting lattice structure by blown powder directed energy deposition was explored. Converging struts were manufactured using multiple lean angles to facilitate the self-supporting structure and to avoid machine-part collisions. The struts showed near uniform straightness relative to a fitted line with a maximum deviation of 1mm at a lean angle of 10°. Micro–hardness and porosity evaluation results showed no significant variation along the struts.

Additive manufacturing↗
DOE OSTI2023

Optimal Dispatch for the US Virgin Islands to Increase Renewable Rates in Saint Croix

The US Virgin Islands, like many other small island nations, face significant challenges related to its energy supply. Their dependency on imported fossil fuels not only drives up energy costs, but also contributes to different environmental problems. Nevertheless, their generally sunny and windy climate makes this archipelago an ideal location for renewable energy development. Increasing the use of sources such as wind, and solar can help reduce their energy dependency, lower their levelized cost of electricity, and improve the health and wellbeing of local communities. In this paper, an optimal dispatcher is employed to analyze the implications on energy security of employing different technology options according to the plans of the local system operator. In this context, short term stability is ensured by inserting operational constraints in the energy management system based on stability analysis developed in PSCAD. The results highlight the usefulness of integrating PV and battery system, while further analysis are required to justify integrating wind power.

energy islands↗
DOE OSTI2021

Revealing the nature of electron correlation in transition metal complexes with symmetry breaking and chemical intuition

Here, in this work, we provide a nuanced view of electron correlation in the context of transition metal complexes, reconciling computational characterization via spin and spatial symmetry breaking in single-reference methods with qualitative concepts from ligand-field and molecular orbital theories. These insights provide the tools to reliably diagnose the multi-reference character, and our analysis reveals that while strong (i.e., static) correlation can be found in linear molecules (e.g., diatomics) and weakly bound and antiferromagnetically coupled (monometal-noninnocent ligand or multi-metal) complexes, it is rarely found in the ground-states of mono-transition-metal complexes. This leads to a picture of static correlation that is no more complex for transition metals than it is, e.g., for organic biradicaloids. In contrast, the ability of organometallic species to form more complex interactions, involving both ligand-to-metal σ-donation and metal-to-ligand π-backdonation, places a larger burden on a theory's treatment of dynamic correlation. We hypothesize that chemical bonds in which inter-electron pair correlation is non-negligible cannot be adequately described by theories using MP2 correlation energies and indeed find large errors vs experiment for carbonyl-dissociation energies from double-hybrid density functionals. A theory's description of dynamic correlation (and to a less important extent, delocalization error), which affects relative spin-state energetics and thus spin symmetry breaking, is found to govern the efficacy of its use to diagnose static correlation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Universal orbital and magnetic structures in infinite-layer nickelates

We conducted a comparative study of the rare-earth infinite-layer nickelate films, RNiO 2 (R = La, Pr, and Nd), using resonant inelastic x-ray scattering (RIXS). We found that the gross features of the orbital configurations are essentially the same, with minor variations in the detailed hybridization. For low-energy excitations, we unambiguously confirm the presence of damped magnetic excitations in all three compounds. By fitting to a linear spin-wave theory, comparable spin exchange coupling strengths and damping coefficients are extracted, indicating a universal magnetic structure in the infinite-layer nickelates. Interestingly, while signatures of a charge order are observed in LaNiO 2 in the quasielastic region of the RIXS spectrum, it is absent in NdNiO 2 and PrNiO 2 . Furthermore, this prompts further investigation into the universality and the origins of charge order within the infinite-layer nickelates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Demonstration of MOOSE-based Griffin reactor physics, code for heterogeneous lead-cooled fast reactor analysis

The MOOSE-based reactor physics code Griffin was assessed on a heterogeneous pin-resolved model of a prototype lead-cooled fast reactor assembly. This model was developed in preparation for future use in MOOSE-based multiphysics calculations for computing hot channel factors. Heterogeneous multigroup cross sections were prepared using the fast reactor multi-group cross section processing code MC{sup 2}-3 using a two-step method. Griffin simulations were performed using the DFEM-SN solver on 576 cores on Argonne's LCRC cluster. Diffusion-based acceleration methods were applied (NDA and CMFD). Reference solutions were generated with continuous energy MCNP and the hybrid MOC/finite element solver PROTEUS-MOC for code-to-code comparison. Space-angle convergence studies were conducted to observe convergence in k-eigenvalue and axial pin power distributions. The fully resolved Griffin calculation was within 68 pcm of the MCNP eigenvalue and exhibited max 1.2% relative error in the axial pin power distribution. Griffin produced nearly identical results to PROTEUS-MOC when using the same 9-group multigroup cross-section set. Griffin demonstrated favorable scaling in wall-clock time and memory usage when using diffusion-based acceleration methods. Griffin is capable of simulating the pin-resolved heterogeneous LFR assembly with good accuracy and performance, and is suitable for future use in coupled high-fidelity hot channel factor simulations. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

Cooperative Automated Cohort Driving on Connected Infrastructure, Arterial Roadways, and Highways: Final Project Demonstration and System-of-Systems Model Correlation

This project seeks to synergize vehicle automated driving and connectivity data to improve mobility and energy efficiency of groups of mixed vehicles operating in close proximity (vehicle cohort) on various infrastructure. A custom cellular communication network links vehicles operating as a cohort with infrastructure to a centralized system-of-systems digital twin with an AI-based optimal behavior planner. The data contained in this set are from final testing and technology demonstrations to U.S. Department of Energy staff at the American Center for Mobility. The data contain single-lane, single-light scenarios; multi-lane, multi-light arterial scenarios; and limited-access highway scenarios. All test cases were derived from simulations and replicated on the test track. The project employed two and four light-duty vehicles with connectivity and drive automation for the testing. The baseline scenario without connectivity was run under the control of the system-of-systems centralized planner but operating each vehicle with an intelligent driver model controlling the velocity, lane utilization, and vehicle gap. This was to ensure the highest compatibility with the simulation in terms of dynamic behavior. The connected cohort case utilized AI optimization to perform coordinated and cooperative control for energy, as well as safe, comfortable behavior for the cohort. The dataset is appropriately named with unconnected and connected designations, with comparisons sharing the same run index number. The included PowerPoint and PDF files describe the test setup and provide an overview of results from the project. ![image](de-EE0009209_March_2023_Data_Arterial_Scenario_Results.png)

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗