Search NASA⌕ Search

SEARCH · Search NASA

Results for “LEE MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Investigation of Wave Energy Converter Effects on the Nearshore Environment: A Month-Long Study in Monterey Bay CA.

A modified version of an indust ry standard wave modeling tool, SNL - SWAN, was used to perform model simulations for hourly initial wave conditio ns measured during the month of October 2009. The model was run with an array of 50 wave energy converters (WECs) and compared with model runs without WECs. Maximum changes in H s were found in the lee of the WEC array along the angles of incident wave dire ction and minimal changes were found along the western side of the model domain due to wave shadowing by land. The largest wave height reductions occurred during observed typhoon conditions and resulted in 14% decreases in H s along the Santa Cruz shoreline . Shoreline reductions in H s were 5% during s outh swell wave conditions and negligible during average monthly wave conditions.

Roberts, Jesse D.↗

Problem Formulation for Optimal Array Modeling and Planning

In this paper we describe an optimal modeling and planning framework for the future large array of DSN antennas. This framework takes into account the array link performance models, reliability models, constrain models, and objective functions, and determines the optimal sub-array clusters configuration that will support the maximum number of concurrent missions based on mission link properties, antenna element reliabilities, mission requests, and array operation constraints. ..

modeling↗

The Power Curve Working Group's Assessment of Wind Turbine Power Performance Prediction Methods

A wind turbine power curve is often only strictly valid for a subset of all atmospheric conditions (i.e., the inner range), while wind turbines also operate in other scenarios (i.e., the outer range). Hence, modeling the power output in real-world conditions is a fundamental challenge. For example, the power deviation matrix (PDM) in Figure 1 displays an overprediction of power production using a reference power curve when wind speed (WS) and turbulence intensity (TI) are both low. Many experts use the PDM approach to observe any systematic bias in power curves and correct this in energy yield models. The mission of the Power Curve Working Group (PCWG) is to bring together wind industry stakeholders to help identify, validate, and develop ways to improve modeling of wind turbine performance in all atmospheric conditions.

17 WIND ENERGY↗

Magnetic dipole γ-ray strength functions in the crossover from spherical to deformed neodymium isotopes

We calculate the magnetic dipole $\gamma$-ray strength functions in a chain of even-mass neodymium isotopes $^{144-152}$Nd in the framework of the configuration-interaction (CI) shell model. We infer the strength function by applying the maximum entropy method (MEM) to the exact imaginary-time response function calculated with the shell-model Monte Carlo (SMMC) method. The success of the MEM depends on the choice of a good strength function as a prior distribution. We investigate two choices for the prior strength function: the static path approximation (SPA) and the quasiparticle random-phase approximation (QRPA). We find that the QRPA is a better approximation at low temperatures (i.e., near the ground state), while the SPA is a better choice at finite temperatures. We identify a low-energy enhancement (LEE) in the MEM deexcitation $M1$ strength functions of the even-mass neodymium isotopes and compare with recent experimental results for the total deexcitation $\gamma$-ray strength functions. The LEE is already seen in the SPA strength function but not in the QRPA strength function, indicating the importance of large-amplitude static fluctuations around the mean field in reproducing the LEE. Our method is currently the only one which can reproduce LEE in heavy open-shell nuclei where conventional CI shell model calculations are prohibited. With the onset of deformation as number of neutrons increases along the chain of neodymium isotopes, we observe that some of the LEE strength transfers to a low-energy excitation, which we interpret as a finite-temperature ``scissors'' mode. Here, we also observe a finite-temperature spin-flip mode.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Viscosity models for pure hydrocarbons at extreme conditions: A review and comparative study

Here, viscosity is a critical fundamental property required in many applications in the chemical and oil industries. In this review the performance of seven select viscosity models, representative of various predictive and correlative approaches, is discussed and evaluated by comparison to experimental data of 52 pure hydrocarbons including straight-chain alkanes, branched alkanes, cycloalkanes, and aromatics. This analysis considers viscosity data to extremely high-temperature, high-pressure conditions up to 573 K and 300 MPa. Unsatisfactory results are found, particularly at high pressures, with the Chung-Ajlan-Lee-Starling, Pedersen-Fredenslund, and Lohrenz-Bray-Clark models commonly used for oil reservoir simulation. If sufficient experimental viscosity data are readily available to determine model-specific parameters, the free volume theory and the expanded fluid theory models provide generally comparable results that are superior to those obtained with the friction theory, particularly at pressures higher than 100 MPa. Otherwise, the entropy scaling method by Lötgering-Lin and Gross is recommended as the best predictive model.

02 PETROLEUM↗

Isotopic Investigations of Nebular and Parent Body Processes with a High Sensitivity Ion Microprobe

NASA supported the development of the CAMECA ims 1270 ion microprobe at UCLA for applications in cosmochemistry. The primary investigations centered on measuring the microscopic distributions of key isotopic abundances in primitive meteoritic materials as a means of constraining the nature of important thermal and chemical processes in the solar nebula and the timescales associated with those processes. Our prior work on oxygen isotope anomalies in a wide variety of meteoritic materials had led us to a view of a spatially heterogeneous nebula, and in particular, a restricted region for CAI formation that is characterized by O-16-rich gas. Because of its production of CAIs in the energetic local environment near the protosun, the existence of a natural transport mechanism via bipolar outflows, and a general astrophysical plausibility, we were attracted to the fluctuating X-wind model which had been put forward by Frank Shu, Typhoon Lee, and colleagues. With our collaborators, we undertook a series of investigations to test the viability of this hypothesis; this work led directly to the discovery of live Be in CAIs and a clear demonstration of the existence of 160-rich condensates, which necessarily implies an O-16-rich gaseous reservoir in the nebula. Both of these observations fit well within the context of X-wind type models, i.e. formation of CAIs (or condensation of their precursors) in the reconnection ring sunward of the inner edge of the accretion disk, however much work remains to be done to test whether the physical parameters of the model can quantitatively predict not only the thermal histories of CAIs but also their radioactivity. The issue of spatial heterogeneity in the nebula, central to the X-wind model, is also at the heart of any chronology based on short-lived radioisotopes. In this work, we followed up on strong hints for presence of exireme:j: (53 day) short-lived Be-7, and have prepared a manuscript (in revision). We also measured A1-Mg systematics by a combined approach of high-precision multiple-collector SIMS analyses, traditional analyses on the UCLA ims 1270, and high-spatial resolution analyses using a NanoSIMS instrument. The data help to deconvolve effects due to partial resetting of the A1-Mg system by multiple thermal events. Finally, we initiated investigations related to nebular heterogeneity with a new initiative of in situ high-precision sulfur isotope analyses of sulfides from a wide variety of components of chondrites. The ultimate goal of all this work is to help develop a better understanding of the relationships between CAIs and chondrules, the astrophysical environments in which they formed, and the timescales of nebular processes. As detailed in Table 1, for the project period, 14 manuscripts were published and 17 abstracts were presented describing the work.

McKeegan, Kevin D.↗

Critical comparison of second-order closures with direct numerical simulations of homogeneous turbulence

Recently, several models have been proposed for closing the second-moment equations, in which the velocity-pressure gradient tensor and the dissipation rate tensor are two of the most important terms. In the literature, these correlation tensors are usually decomposed into a so-called rapid term and a return-to-isotropy term. Models of these terms have been used in global flow calculations together with other modeled terms. However, their individual behaviors in different flows have not been fully examined because they are unmeasurable in the laboratory. Recently, the development of direct numerical simulation (DNS) of turbulence has given us the possibility to do this kind of study. With direct numerical simulation, we may use the solution to calculate exactly the values of these correlation terms and then directly compare them with the values from their modeled formulations. In this paper, we make direct comparisons of five representative rapid models and eight return-to-isotropy models using the DNS data of 45 homogeneous flows, which were done by Rogers et al. (1986) and Lee and Reynolds (1985). The purpose of these direct comparisons is to explore the performance of these models in different flows and identify the ones that give the best performance. The paper also describes the modeling procedure, model constraints, and the various evaluated models. The detailed results of the direct comparisons are discussed, and a few concluding remarks on turbulence models are given.

Shih, Tsan-Hsing↗

Flood hazard model calibration using multiresolution model output

Riverine floods pose a considerable risk to many communities. Improving flood hazard projections has the potential to inform the design and implementation of flood risk management strategies. Current flood hazard projections are uncertain, especially due to uncertain model parameters. Calibration methods use observations to quantify model parameter uncertainty. With limited computational resources, researchers typically calibrate models using either relatively few expensive model runs at high spatial resolutions or many cheaper runs at lower spatial resolutions. This leads to an open question: is it possible to effectively combine information from the high and low resolution model runs? We propose a Bayesian emulation–calibration approach that assimilates model outputs and observations at multiple resolutions. As a case study for a riverine community in Pennsylvania, we demonstrate our approach using the LISFLOOD-FP flood hazard model. Here, the multiresolution approach results in improved parameter inference over the single resolution approach in multiple scenarios. Results vary based on the parameter values and the number of available models runs. Our method is general and can be used to calibrate other high dimensional computer models to improve projections.

multiresolution↗

Direct CP, Lepton Flavor, and Isospin Asymmetries in the Decays B{yields}K{sup (*)}l{sup +}l{sup -}

We measure branching fractions and integrated rate asymmetries for the rare decays B{yields}K{sup (*)}l{sup +}l{sup -}, where l{sup +}l{sup -} is either e{sup +}e{sup -} or {mu}{sup +}{mu}{sup -}, using a sample of 384x10{sup 6} BB events collected with the BABAR detector at the PEP-II e{sup +}e{sup -} collider. We find no evidence for direct CP or lepton-flavor asymmetries. However, for dilepton masses below the J/{psi} resonance, we find evidence for unexpectedly large isospin asymmetries in both B{yields}Kl{sup +}l{sup -} and B{yields}K*l{sup +}l{sup -} which differ, respectively, by 3.2{sigma} and 2.7{sigma}, including systematic uncertainties, from the standard model expectations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A critical comparison of second order closures with direct numerical simulation of homogeneous turbulence

Recently, several second order closure models have been proposed for closing the second moment equations, in which the velocity-pressure gradient (and scalar-pressure gradient) tensor and the dissipation rate tensor are two of the most important terms. In the literature, these correlation tensors are usually decomposed into a so called rapid term and a return-to-isotropy term. Models of these terms have been used in global flow calculations together with other modeled terms. However, their individual behavior in different flows have not been fully examined because they are un-measurable in the laboratory. Recently, the development of direct numerical simulation (DNS) of turbulence has given us the opportunity to do this kind of study. With the direct numerical simulation, we may use the solution to exactly calculate the values of these correlation terms and then directly compare them with the values from their modeled formulations (models). Here, we make direct comparisons of five representative rapid models and eight return-to-isotropy models using the DNS data of forty five homogeneous flows which were done by Rogers et al. (1986) and Lee et al. (1985). The purpose of these direct comparisons is to explore the performance of these models in different flows and identify the ones which give the best performance. The modeling procedure, model constraints, and the various evaluated models are described. The detailed results of the direct comparisons are discussed, and a few concluding remarks on turbulence models are given.

Shih, Tsan-Hsing↗

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al{sub 2}O{sub 3}-TiN and MgAl{sub 2}O{sub 4}-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl{sub 2}O{sub 4}-TiN interface rather than that of Al{sub 2}O{sub 3}-TiN interface. When ∆T{sub TiN} (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

36 MATERIALS SCIENCE↗

A PAUF-neutralizing antibody targets both carcinoma and endothelial cells to impede pancreatic tumor progression and metastasis

Highlights: • PMAb83, a human monoclonal antibody against PAUF, impaired tumor progression in vivo. • PMAb83 attenuated aggressiveness of tumor cells and suppressed angiogenesis. • PMAb83 in combination with gemcitabine conferred improved survival of mouse model. - Abstract: Pancreatic adenocarcinoma up-regulated factor (PAUF) is expressed in pancreatic ductal adenocarcinoma (PDAC) and plays an important role in tumor progression and metastasis. Here we evaluate the anti-tumor efficacy of a human monoclonal antibody against PAUF, PMAb83, to provide a therapeutic intervention to treat the disease. PMAb83 reduced tumor growth and distant metastasis in orthotopically xenografted mice of human PDAC cells. PMAb83 treatment retarded proliferation along with weakened aggressiveness traits of the carcinoma cells. AKT/β-catenin signaling played a role in the carcinoma cell proliferation and the treated xenograft tumors exhibited reduced levels of β-catenin and cyclin D1. Moreover PMAb83 abrogated the PAUF-induced angiogenic responses of endothelial cells, reducing the density of CD31{sup +} vessels in the treated tumors. In combination with gemcitabine, PMAb83 conferred enhanced survival of xenografted mice by about twofold compared to gemcitabine alone. Taken together, our findings show that PMAb83 treatment decreases the aggressiveness of carcinoma cells and suppresses tumor vascularization, which culminates in mitigated tumor growth and metastasis with improved survival in PDAC mouse models.

60 APPLIED LIFE SCIENCES↗

An experiment-informed discrete element modelling study of knife milling for flexural biomass feedstocks

A discrete element method (DEM) based approach is used to study the relationships between material attributes (MAs), processing parameters (PPs), and quality attributes (QAs) for the knife milling of maize stalks. An approximate DEM shape model was conceptualized based on real maize stalks and calibrated based on experimental bending test data for flexural properties (elastic bending stiffness, elastic bending angle limit, elastoplastic ratio, etc.). DEM simulations of maize stalk comminution in a Jordan Reduction Solutions (“JRS”) knife mill were performed to investigate the relationships between the MAs (maize stalk size and breakage stress limit), PPs (impeller rotational speed), and QAs (mass throughput and output particle size distribution (PSD)). The DEM results suggest that stalk length has little influence on mass throughput and PSD, whilst stalks with larger cross sections tend to generate larger sizes of milled particles given the same breakage stress limit. Both the DEM and experimental results show that faster impeller rotation (or higher power) does not necessarily generate higher throughput or smaller output PSD, especially for maize stalks of higher breakage stress limit. The correlations between these MAs, PPs and QAs are found highly stochastic, though breakage stress limit dictates mass throughput, regardless of stalk size. The DEM-predicted output particle size tended to match the experimental data with coarse PSDs based on sieve size but showed weakened fidelity with finer material, indicating the potential for further model improvement.

09 BIOMASS FUELS↗

Minimizing total energy cost and tardiness penalty for a scheduling-layout problem in a flexible job shop system: A comparison of four metaheuristic algorithms

Job scheduling and machine layout are interrelated in improving energy consumption (EC) and productivity measures such as tardiness and represent two important decisions that must be made by manufacturers. This interdependency can be explained by transportation time, which connects scheduling and layout. Scheduling and layout, however, have not been thoroughly studied in conjunction using an integrated model in the context of sustainable manufacturing. Hence, we propose an energy-aware optimization model in which scheduling is integrated with layout in a single-level framework. More specifically, a single objective function is defined to minimize the facility energy cost and the job tardiness penalty, which control EC and tardiness respectively in a flexible job shop system. In order to model machine EC more accurately, we also consider three different machine states: a processing state and two idle states. Our case studies show that the integrated model exhibits better performance in controlling manufacturing EC and job tardiness than a non-integrated model in which machine locations are uncontrollable and transportation times between machines are unchangeable. To deal with large-sized problems, we also introduce four new metaheuristics. The performances of these new metaheuristics are compared in terms of objective function values and CPU times using various case studies. The results indicate that a hybrid ant colony optimization and simulated annealing (ACO-SA) algorithm provides better performance than the other algorithms. Specifically, our case studies show that the integrated model using ACO-SA can improve the objective function value by around 5% when compared to the non-integrated model.

42 ENGINEERING↗

Convenient Confinement: Interplay of Solution Conditions and Graphene Oxide Film Structure on Rare Earth Separations

Graphene oxide (GO) membranes are excellent candidates for a range of separation applications, including rare earth segregation and radionuclide decontamination. Understanding nanoscale water and ion behavior near interfacial GO is critical for groundbreaking membrane advances, including improved selectivity and permeability. Here, we experimentally examine the impact of solution conditions on water and lanthanide interactions with interfacial GO films and connect these results to GO membrane performance. The investigation of the confined films at the air–water interface with a combination of surface-specific spectroscopy and X-ray scattering techniques allows us to understand water and ion behaviors separately. Sum frequency generation spectroscopy reveals a dramatic change in interfacial water organization because of graphene oxide film deprotonation. Interfacial X-ray fluorescence measurements show a 17× increase in adsorbed lanthanide to the GO film from subphase pH 3 to pH 9. Liquid surface X-ray reflectivity data show an additional 2.7 $e^–$ per Å 2 for GO films at pH 9 versus pH 3 as well. These results are connected to GO membrane performance, which show increased selectivity and decreased flux for membranes filtering pH 9 solutions. We posit insoluble lanthanide hydroxides form at higher pHs. Taken together, these results highlight the importance of interfacial experiments on model GO systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temperature-dependent energy band gap variation in self-organized InAs quantum dots

We investigated the temperature-dependent variation of the photoluminescence emission energy of self-organized InAs/GaAs quantum dots (QDs) grown by conventional Stranski-Krastanov (SK) molecular beam epitaxy and migration-enhanced molecular beam epitaxy (MEMBE) and that of MEMBE InAs QDs in a symmetric and an asymmetric In{sub 0.2}Ga{sub 0.8}As/GaAs well. The temperature-dependent energy variation of each QD is analyzed in low and high temperature regions, including a sigmoidal behavior of conventional SK quantum dots with the well-known Varshni and semi-empirical Fan models.

36 MATERIALS SCIENCE↗