Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Effect of winglets on a first-generation jet transport wing. 6: Stability characteristics for a full-span model at subsonic speeds

A wind tunnel investigation to identify changes in stability and control characteristics of a model KC-135A due to the addition of winglets is presented. Static longitudinal and lateral-directional aerodynamic characteristics were determined for the model with and without winglets. Variations in the aerodynamic characteristics at various Mach numbers, angles of attack, and angles of slidslip are discussed. The effect of the winglets on the drag and lift coefficients are evaluated and the low speed and high speed characteristics of the model are reported.

Flechner, S. G.↗
NASA NTRS1979

Theoretical study of aerodynamic characteristics of wings having vortex flow

The aerodynamic characteristics of slender wings having separation induced vortex flows are investigated by employing three different computer codes--free vortex sheet, quasi vortex lattice, and suction analogy methods. Their capabilities and limitations are examined, and modifications are discussed. Flat wings of different configurations: arrow, delta, and diamond shapes, as well as cambered delta wings, are studied. The effect of notch ratio on the load distributions and the longitudinal characteristics of a family of arrow and diamond wings is explored. The sectional lift coefficients and the accumulated span loadings are determined for an arrow wing and are seen to be unusual in comparison with the attached flow results. The theoretically predicted results are compared with the existing experimental values.

Reddy, C. S.↗
NASA NTRS1979

Altitude response of several airplanes during landing approach

The response in altitude and pitching velocity of the shuttle and of four other airplanes during the landing approach is compared. The effects of airplane type, pitch damping, center-of-gravity location, lift coefficient, and cockpit position are presented. The reasons for the differences observed and the effects of these differences on control characteristics are discussed.

Phillips, W. H.↗
NASA NTRS1979

Exploratory studies of the cruise performance of upper surface blown configuration: Experimental program, high-speed force tests

The work to develop a wing-nacelle arrangement to accommodate a wide range of upper surface blown configuration is reported. Pertinent model and installation details are described. Data of the effects of a wide range of nozzle geometric variations are presented. Nozzle aspect ratio, boattail angle, and chordwise position are among the parameters investigated. Straight and swept wing configurations were tested across a range of nozzle pressure ratios, lift coefficients, and Mach numbers.

Braden, J. A.↗
NASA NTRS1980

An analysis method for multi-component airfoils in separated flow

The multi-component airfoil program (Langley-MCARF) for attached flow is modified to accept the free vortex sheet separation-flow model program (Analytical Methods, Inc.-CLMAX). The viscous effects are incorporated into the calculation by representing the boundary layer displacement thickness with an appropriate source distribution. The separation flow model incorporated into MCARF was applied to single component airfoils. Calculated pressure distributions for angles of attack up to the stall are in close agreement with experimental measurements. Even at higher angles of attack beyond the stall, correct trends of separation, decrease in lift coefficients, and increase in pitching moment coefficients are predicted.

Rao, B. M.↗
NASA NTRS1980

Preliminary design characteristics of a subsonic business jet concept employing an aspect ratio 25 strut braced wing

The advantages of replacing the conventional wing on a transatlantic business jet with a larger, strut braced wing of aspect ratio 25 were evaluated. The lifting struts reduce both the induced drag and structural weight of the heavier, high aspect ratio wing. Compared to the conventional airplane, the strut braced wing design offers significantly higher lift to drag ratios achieved at higher lift coefficients and, consequently, a combination of lower speeds and higher altitudes. The strut braced wing airplane provides fuel savings with an attendant increase in construction costs.

Turriziani, R. V.↗
NASA NTRS1980

Experimental and theoretical aerodynamic characteristics of two hypersonic cruise aircraft concepts at Mach numbers of 2.96, 3.96, and 4.63

The longitudinal and lateral directional aerodynamic characteristics for two Mach 5 cruise aircraft concepts were determined for test Mach numbers of 2.96, 3.96, and 4.63. Estimates from hypersonic impact theory and first order supersonic linearized theory were compared with data to indicate the usefulness of these methods. The method which applied tangent cone empirical theory to the body and tangent wedge theory to the wings and to the horizontal and vertical tails provided the best estimates. The tangent cone empirical theory applied to all components showed poor agreement with data, and the linear theory estimates were accurate only for lift coefficient and drag coefficient at low angles of attack.

Pittman, J. L.↗
NASA NTRS1980

Effect of wing location and strakes on stability and control characteristics of a monoplanar circular missile with low-profile tail fins at supersonic speeds

A wind tunnel test was conducted at Mach numbers from 1.70 to 2.86 to extend the aerodynamic data base for wing tail effect on stability and control characteristics of monoplanar missiles. The results are summarized to show the effects of tail fin dihedral angle, wing location, and nose body strakes. The results indicate that an increase in tail fin dihedral angle produces positive increments in directional stability that allow greater trimmed lift coefficient values (maneuver potential) to be obtained. An increase in wing tail gap for the Mach number range reduces the aerodynamic center travel and produces reductions in directional stability at the lower angles of attack. A change in wing height (vertical location) strongly influences the angle of attack at which pitch up and the most directional stability occur. The addition of strakes to the baseline configuration increases directional stability, which allows a significant increase in stable trimmed maneuver capability. The tail fins of the baseline configuration are effective in producing roll and yaw control that are accompanied by favorable yaw and roll, respectively.

Blair, A. B., Jr.↗
NASA NTRS1981

Exploratory subsonic investigation of vortex-flap concept on arrow wing configuration

The drag reduction potential of a vortex flap concept, utilizing the thrust contribution of separation vortices maintained over leading edge flap surfaces, was explored in subsonic wind tunnel tests on a highly swept arrow wing configuration. Several flap geometries were tested in comparison with a previous study on the same model with leading edges drooped for attached flow. The most promising vortex flap arrangements produced drag reductions comparable with leading edge droop over a range of lift coefficients from 0.3 to 0.6 (untrimmed), and also indicated beneficial effects in the longitudinal and lateral static stability characteristics.

Rao, D. M.↗
NASA NTRS1981

Investigation of powered nacelles on a high aspect ratio NASA supercritical wing, phase 2

A modified wing with the long core separate flow nacelle and several E(3) nacelles was utilized. The effects of nacelle and pylon cant angles and nacelle longitudinal and vertical location were investigated over a Mach number range from 0.70 to 0.83. The results at the cruise condition 0.82 Mach number and 0.55 lift coefficient are presented.

Flechner, S. G.↗
NASA NTRS1981

Recent Progress in V/STOL Aircraft Technology

Results from wind tunnel and flight tests investigations for V/STOL aircraft are reviewed. Primary emphasis is given to technical results relating to three types of subsonic aircraft: a quiet STOL aircraft; a tilt rotor aircraft; and a turbofan V/STOL aircraft. Comparison and correlation between theoretical and experimental results and between wind tunnel and flight test results, is made. The quiet STOL aircraft technology results are primarily those derived from the NASA/Boeing Quiet Short Haul Technology (QSRA) program. The QSRA aircraft uses an upper surface blown flap and develops a usable engine-out landing approach lift coefficient of 5.5 and landing distances less than 1,000 ft. The tilt rotor aircraft technology results are those obtained from the NASA/Army/Navy/Bell (XV-15-TRRA) aircraft flight investigations. The TRRA is a twin rotor research aircraft capable of vertical takeoff and landing and cruise speeds of 300 knots. The turbofan V/STOL aircraft technology results are from static ground facility and wind tunnel investigations of a NASA/NAVY/Grumman full scale lift/cruise fan aircraft model, which features two tilting nacelles with TF-34 engines.

Roberts, L.↗
NASA NTRS1981

Pressure and force data for a flat wing and a warped conical wing having a shockless recompression at Mach 1.62

A conical nonlinear flow computer code was used to design a warped (cambered) wing which would produce a supercritical expansion and shockless recompression of the crossflow at a lift coefficient of 0.457, an angle of attack of 10 deg, and a Mach number of 1.62. This cambered wing and a flat wing the same thickness distribution were tested over a range of Mach numbers from 1.6 to 2.0. For both models the forward 60 percent is purely conical geometry. Results obtained with the cambered wing demonstrated the design features of a supercritical expansion and a shockless recompression, whereas results obtained with the flat wing indicated the presence of crossflow shocks. Tables of experimental pressure, force, and moment data are included, as well as selected oil flow photographs.

Miller, D. S.↗
NASA NTRS1981

Analytical study of the cruise performance of a class of remotely piloted, microwave-powered, high-altitude airplane platforms

Each cycle of the flight profile consists of climb while the vehicle is tracked and powered by a microwave beam, followed by gliding flight back to a minimum altitude. Parameter variations were used to define the effects of changes in the characteristics of the airplane aerodynamics, the power transmission systems, the propulsion system, and winds. Results show that wind effects limit the reduction of wing loading and increase the lift coefficient, two effective ways to obtain longer range and endurance for each flight cycle. Calculated climb performance showed strong sensitivity to some power and propulsion parameters. A simplified method of computing gliding endurance was developed.

Morris, C. E. K., Jr.↗
NASA NTRS1981

Design and Experimental Results for a Natural-Laminar-Flow Airfoil for General Aviation Applications

A natural-laminar-flow airfoil for general aviation applications, the NLF(1)-0416, was designed and analyzed theoretically and verified experimentally in the Langley Low-Turbulence Pressure Tunnel. The basic objective of combining the high maximum lift of the NASA low-speed airfoils with the low cruise drag of the NACA 6-series airfoils was achieved. The safety requirement that the maximum lift coefficient not be significantly affected with transition fixed near the leading edge was also met. Comparisons of the theoretical and experimental results show excellent agreement. Comparisons with other airfoils, both laminar flow and turbulent flow, confirm the achievement of the basic objective.

Somers, D. M.↗
NASA NTRS1980

An experimental investigation of three dimensional low speed minimum interference wind tunnel for high lift wings

As a means to achieve a minimum interference correction wind tunnel, a partially actively controlled test section was experimentally examined. A jet flapped wing with 0.91 m (36 in) span and R = 4.05 was used as a model to create moderately high lift coefficients. The partially controlled test section was simulated using an insert, a rectangular box 0.96 x 1.44 m (3.14 x 4.71 ft) open on both ends in the direction of the tunnel air flow, placed in the University of Washington Aeronautical Laboratories (UWAL) 2.44 x 3.66 m (8 x 12 ft) wind tunnel. A tail located three chords behind the wing was used to measure the downwash at the tail region. The experimental data indicates that, within the range of momentum coefficient examined, it appears to be unnecessary to actively control all four sides of the test section walls in order to achieve the near interference free flow field environment in a small wind tunnel. The remaining wall interference can be satisfactorily corrected by the vortex lattice method.

Shindo, S.↗
NASA NTRS1981

An ABC status report

The Advancing Blade Concept (ABC) uses two rigid counterrotating rotors in a coaxial arrangement to provide advancing blades on both sides of the aircraft. This makes use of the high dynamic pressure on the advancing side of the rotors at high forward speed, virtually ignoring the low dynamic pressure on the retreating side, while still keeping the rotor system in roll trim. Theoretically such a rotor system will maintain its lift potential as speed increases. The XH-59A was designed to investigate this theory. A description is provided of the flight test program from May, 1980 to January, 1981. A summary is presented of the knowledge gained throughout the entire program, and current pitfalls are reviewed. It is concluded that the ABC has been verified, with the XH-59A envelope of blade lift coefficient as a function of advance ratio greatly exceeding that of conventional helicopter rotor systems.

Linden, A. W.↗
NASA NTRS1951

An Empirical Method Permitting Rapid Determination of the Area, Rate and Distribution of Water-Drop Impingement on an Airfoil of Arbitrary Section at Subsonic Speeds

An empirical method for the determination of the area, rate, and distribution of water-drop impingement on airfoils of arbitrary section is presented. The procedure represents an initial step toward the development of a method which is generally applicable in the design of thermal ice-prevention equipment for airplane wing and tail surfaces. Results given by the proposed empirical method are expected to be sufficiently accurate for the purpose of heated-wing design, and can be obtained from a few numerical computations once the velocity distribution over the airfoil has been determined. The empirical method presented for incompressible flow is based on results of extensive water-drop. trajectory computations for five airfoil cases which consisted of 15-percent-thick airfoils encompassing a moderate lift-coefficient range. The differential equations pertaining to the paths of the drops were solved by a differential analyzer. The method developed for incompressible flow is extended to the calculation of area and rate of impingement on straight wings in subsonic compressible flow to indicate the probable effects of compressibility for airfoils at low subsonic Mach numbers.

Bergrun, N. R.↗
NASA NTRS1981

Parametric study of microwave-powered high-altitude airplane platforms designed for linear flight

The performance of a class of remotely piloted, microwave powered, high altitude airplane platforms is studied. The first part of each cycle of the flight profile consists of climb while the vehicle is tracked and powered by a microwave beam; this is followed by gliding flight back to a minimum altitude above a microwave station and initiation of another cycle. Parametric variations were used to define the effects of changes in the characteristics of the airplane aerodynamics, the energy transmission systems, the propulsion system, and winds. Results show that wind effects limit the reduction of wing loading and the increase of lift coefficient, two effective ways to obtain longer range and endurance for each flight cycle. Calculated climb performance showed strong sensitivity to some power and propulsion parameters. A simplified method of computing gliding endurance was developed.

Morris, C. E. K., Jr.↗