Microstructure evolution in vapor-deposited Hexanitroazobenzene (HNAB) films.
No abstract prepared.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
No abstract prepared.
Morphology and microstructure of organic explosive films formed using physical vapor deposition (PVD) processes strongly depends on local surface temperature during deposition. Currently, there is no accurate means of quantifying the local surface temperature during PVD processes in the deposition chambers. This study focuses on using a multiphysics computational fluid dynamics tool, STARCCM+, to simulate pentaerythritol tetranitrate (PETN) deposition. The PETN vapor and solid phase were simulated using the volume of fluid method and its deposition in the vacuum chamber on spinning silicon wafers was modeled. The model also included the spinning copper cooling block where the wafers are placed along with the chiller operating with forced convection refrigerant. Implicit time-dependent simulations in two- and three-dimensional were performed to derive insights in the governing physics for PETN thin film formation. PETN is deposited at the rate of 14 nm/s at 142.9 °C on a wafer with an initial temperature of 22 °C. The deposition of PETN on the wafers was calculated at an assumed heat transfer coefficient (HTC) of 400 W/m 2 K. This HTC proved to be the most sensitive parameter in determining the local surface temperature during deposition. Previous experimental work found noticeable microstructural changes with 0.5 mm fused silica wafers in place of silicon during the PETN deposition. This work showed that fused silica slows initial wafer cool down and results in ~10 °C difference for the surface temperature at 500 μm PETN film thickness. It was also found that the deposition surface temperature is insensitive to the cooling power of the copper block due to the copper block's very large heat capacity and thermal conductivity relative to the heat input from the PVD process. Future work should incorporate the addition of local stress during PETN deposition. Lastly, based on simulation results, it is also recommended to investigate the impact of wafer surface energy on the PETN microstructure and morphology formation.
Nanocrystalline metals are generally unstable due to a large volume fraction of high-energy grain boundaries associated with a small grain size. Preferential dopant segregation to the high-energy grain boundaries is observed to enhance the stability of the material’s microstructure by minimizing its energy. Nanocrystalline aluminum-dopant systems were evaluated for thermodynamic stability against grain growth and phase precipitation via the mechanism of grain boundary segregation according to a modified regular nanocrystalline solution model. Fifty-one potential dopant elements have been evaluated for their efficacy in stabilizing nanostructures with three potential candidates, magnesium, lanthanum, and silicon, identified possessing the characteristics to promote grain boundary segregation and a state of thermodynamic stability in aluminum’s nanocrystalline regime. Here, the minimum dopant content required to achieve nanocrystalline microstructure stability is identified for each of the three candidate elements. Beyond this minimum content, further addition of the dopant elements decreased the final microstructure’s stability with no effects on the existence of a stable nanocrystalline state.
Operation of energy storage and conversion devices is ultimately controlled by series of intertwined ionic and electronic transport processes and electrochemical reactions at surfaces and interfaces, strongly mediated by strain and mechanical processes [1-4]. In a typical fuel cell, these include chemical species transport in porous cathode and anode materials, gas-solid electrochemical reactions at grains and triple-phase boundaries (TPBs), ionic and electronic flows in multicomponent electrodes, and chemical and electronic potential drops at internal interfaces in electrodes and electrolytes. All these phenomena are sensitively affected by the microstructure of materials from device level to the atomic scales as illustrated in Fig. 1. Similar spectrum of length scales and phenomena underpin operation of other energy systems including primary and secondary batteries, as well as hybrid systems such flow and metal-air/water batteries.
This study proposes an approach for capturing the effect of microstructural evolution on reactor fuel performance by coupling a mesoscale irradiated microstructure model with a finite element fuel performance code. To achieve this, the macroscale system is solved in a parallel, fully coupled, fully-implicit manner using the preconditioned Jacobian-free Newton Krylov (JFNK) method. Within the JFNK solution algorithm, microstructure-influenced material parameters are calculated by the mesoscale model and passed back to the macroscale calculation. Due to the stochastic nature of the mesoscale model, a dynamic fitting technique is implemented to smooth roughness in the calculated material parameters. The proposed methodology is demonstrated on a simple model of a reactor fuel pellet. In the model, INL’s BISON fuel performance code calculates the steady-state temperature profile in a fuel pellet and the microstructure-influenced thermal conductivity is determined with a phase field model of irradiated microstructures. This simple multiscale model demonstrates good nonlinear convergence and near ideal parallel scalability. By capturing the formation of large mesoscale voids in the pellet interior, the multiscale model predicted the irradiation-induced reduction in the thermal conductivity commonly observed in reactors.
Here, in a magnetic fusion energy (MFE) device, the plasma-facing materials (PFMs) will be subjected to tremendous fluxes of ions, heat, and neutrons. The response of PFMs to the fusion environment is still not well defined. Tungsten metal is the present candidate of choice for PFM applications such as the divertor in ITER. However, tungsten's microstructure will evolve in service, possibly to include recrystallization. How tungsten's response to plasma exposure evolves with changes in microstructure is presently unknown. In this work, we have exposed hot-worked and recrystallized tungsten to an 80 eV helium ion beam at a temperature of 900 °C to fluences of 2 × 10 23 or 20 × 10 23 He/m 2 . This resulted in a faceted surface structure at the lower fluence or short but well-developed nanofuzz structure at the higher fluence. There was little difference in the hot-rolled or recrystallized material's near-surface (≤50 nm) bubbles at either fluence. At higher fluence and deeper depth, the bubble populations of the hot-rolled and recrystallized were different, the recrystallized being larger and deeper. This may explain previous high-fluence results showing pronounced differences in recrystallized material. The deeper penetration in recrystallized material also implies that grain boundaries are traps, rather than high-diffusivity paths.
Among current deep learning approaches for synthetic image generation, diffusion-based models stand out in terms of algorithmic stability and ability to retain high-fidelity image features with detailed resolution. Here, in this work, we employ Dreambooth, a method for fine-tuning Stable Diffusion, on X-ray CT images of microstructure of the polymer-bonded form (PBX) of a commonly used high explosive, Pentaerythritol tetranitrate (PETN), which yields generative models for creating synthetic PBX images. The models developed here represent five classes (or ‘lots’) of microstructures and demonstrate successful generation of images of each class with high fidelity, as verified by computed classification accuracy of ∼ 94% or higher. Data augmentation afforded by such image synthesis can be used to more reliably decipher underlying statistics, build processing-structure correlations, recognize off-normal structural anomalies, and identify age-related changes. Ideas related to converting image data into appropriate density mapping and performing mesoscale simulation or surrogate modeling of detonation are also discussed.
Cold rolling and annealing of homogenized Fe-Ni-Mn-Mo-Ti-Cr maraging steels resulted in the formation of submicrocrystalline Fe{sub 2}(Mo,Ti) Laves phase particles. Optical and scanning electron microscopy, X-ray diffraction, tensile and hardness tests were used to study the microstructure, aging behavior and mechanical properties of the annealed steels. The annealed microstructures showed age hardenability during subsequent isothermal aging at 753 K. Ultrahigh fracture stress but poor tensile ductility was obtained after substantial age hardening in the specimens with 2% and 4% chromium. Increasing chromium addition up to 6% toughened the aged microstructure at the expense of the fracture stress by increasing the volume fraction of retained austenite. The Laves phase particles acted as crack nucleation sites during tensile deformation. - Highlights: {yields} Laves phases dispersed in a BCC iron matrix by annealing of cold rolled samples. {yields} The samples showed age hardenability during subsequent isothermal aging at 753 K. {yields} Ultrahigh fracture stress but poor ductility was obtained after age hardening. {yields} Increasing chromium addition toughened the aged microstructure. {yields} Laves phase particles acting as crack nucleation sites during tensile deformation.
The concept of twin-limited microstructures has been explored in the literature as a crystallographically constrained grain boundary network connected via only coincident site lattice (CSL) boundaries. The advent of orientation imaging has made classification of twin-related domains (TRD) or any other orientation cluster experimentally accessible in 2D using EBSD. With the emergence of 3D orientation mapping, a comparison of TRDs in measured 3D microstructures is performed in this paper and compared against their 2D counterparts. The TRD analysis is performed on a conventionally processed (CP) and a grain boundary engineered (EM) high purity copper sample that have been subjected to successive anneal procedures to promote grain growth. Finally, the EM sample shows extremely large TRDs which begin to approach that of a twin-limited microstructure, while the TRDs in the CP sample remain relatively small and remote.
The effect of testing conditions (temperature, time, and oxygen content) and material's microstructure (the as-received and the grain boundary engineered conditions) on the corrosion behavior of alloy 800H in high-temperature pressurized water was studied using a variety of characterization techniques. Oxidation was observed as the primary corrosion behavior on the samples. Oxide exfoliation was significantly mitigated on the grain boundary engineered samples compared to the as-received ones. The oxide formation, including some 'mushroom-shaped oxidation', is predicted via a combination of thermodynamics and kinetics influenced by the preferential diffusion of specific species using short-cut diffusion paths.
In an effort to contribute to the development of advanced nuclear fuel for research reactors, monolithic and dispersion plate fuels will be examined to determine how irradiation parameters such as fission density, fission rate, and irradiation temperature, as well as mechanical parameters such as composition and fabrication, affect the final microstructure of the fuel, post irradiation. Electron Backscatter Detection (EBSD) analysis capabilities of irradiated materials will be developed as well as improvements on irradiated sample preparation in order to provide higher quality samples for SEM, FIB, and TEM. In addition, image analysis techniques developed at Idaho National Laboratory (INL) will be employed to examine microstructural features such as fission product precipitates and fission gas bubbles. The main goals are to further develop EBSD capabilities on irradiated material; characterize microstructure of irradiated fuel to support qualification; develop a consistent, effective process for image analysis using INL developed software; and provide repeatable, statistically-confident, critically assessed data to further modeling efforts. (authors)
Operation of energy storage and conversion devices is ultimately controlled by series of intertwined ionic and electronic transport processes and electrochemical reactions at surfaces and interfaces, strongly mediated by strain and mechanical processes. In a typical fuel cell, these include chemical species transport in porous cathode and anode materials, gas-solid electrochemical reactions at grains and triple-phase boundaries (TPBs), ionic and electronic flows in multicomponent electrodes, and chemical and electronic potential drops at internal interfaces in electrodes and electrolytes. Furthermore, all these phenomena are sensitively affected by the microstructure of materials from device level to the atomic scales. Similar spectrum of length scales and phenomena underpin operation of other energy systems including primary and secondary batteries, as well as hybrid systems such flow and metal-air/water batteries.
The issue of variable bandgap values for InN films grown on c-sapphire has been addressed in this work. {alpha}-InN films have been deposited in nitrogen rich condition at different substrate temperatures on bare Al{sub 2}O{sub 3} (0001) by plasma assisted molecular beam epitaxy (PA-MBE). The results of several complementary characterization techniques show that single crystalline wurtzite InN is formed, but their orientation depends on the substrate temperature. The bandgap measured on these samples (1.78 eV) is explained by Moss-Burstein shift on these degenerately n-doped samples. Our results discount effects of crystal orientation, presence of oxygen at grain boundaries and In/N stoichiometry as factors that influence the measured band-gap values.
High-pressure minerals such as coesite, stishovite, and reidite are often used as indicators of shock metamorphism. However, high-pressure and high-temperature phases are metastable at ambient conditions and, therefore, often revert to a more energetically favorable phase. During solid-state transformations, the crystallographic orientations of the stable polymorph are controlled by the transformation pathway from the parent. Microstructural orientation analysis using electron backscatter diffraction (EBSD) of the stable phase can reveal systematic intercrystalline orientation relationships (OR) diagnostic of solid-state transformations from these high-pressure or high-temperature polymorph phases (Cayron et al., 2006). Knowledge of polymorph stability fields for a given system can thus be used to infer minimum shock P and/or T conditions that rocks have experienced, which are otherwise unavailable using traditional thermobarometers such as element partition coefficients. Using orientation relationships to infer the former presence of mineral phases has been termed microstructural “phase heritage”, and has successfully been used to probe for evidence of extreme pressures and temperatures resulting from hypervelocity impacts. The reconstruction of polymorphs of ZrSiO4 (zircon, reidite) and ZrO2 (baddeleyite) have further elucidated the behavior of these phases under hypervelocity impact conditions (Timms et al., 2017a; White et al., 2018), and OR analysis of shocked monazite has identified a previously unrecognized tetragonal high-P polymorph (Erickson et al., 2019). Zircon will convert to the low tetragonal polymorph reidite at shock stresses above ~21 GPa. However, upon decompression at temperatures above 1200 °C reidite will revert to zircon (Kusaba et al., 1985). Recrystallized zircon neoblasts encased in impact melt often show systematic misorientation relationships of 90° about <110> indicative of reversion from the reidite (Fig. 1), and preserving cryptic evidence of the high-P history that is often erased by the post shock thermal spike (Cavosie et al., 2016). Microstructural OR analysis of a dissociated zircon corona composed of baddeleyite (monoclinic-ZrO2) has identified the former presence of cubic zirconia within impact melt glass from the Mistastin Lake impact structure, Labrador, CA. Based on stability fields in the ZrO2-SiO2 binary phase diagram, cubic zirconia records thermal conditions in excess of 2370 °C at ambient P, indicating that the Mistastin impact melt is the hottest rock identified on Earth’s surface (Timms et al., 2017b). Shock-deformed monazite (monoclinic La,Ce,ThPO4) containing lamellae comprised of interlocking laths has been identified from the Haughton Dome impact structure, Nunavut, Canada and Nördlinger-Ries Crater, southern Germany. The lath-structured lamellae are composed of four systematic orientation variants, which OR analyses indicate originate from a tetragonal parent whereby the [010]monoclinic aligns with either [100] or [010]tetragonal (Erickson et al., 2019). These results highlight utility of microstructural phase heritage analyses for the identification of unstable high-P or high-T polymorphs that uniquely record the extremely transient shock conditions produced by hypervelocity impacts.
A two-step sintering process has been adopted to produce NiZn ferrite with composition of (NiO){sub 0.35}(ZnO){sub 0.57}(CuO){sub 0.08}(Fe{sub 2}O{sub 3}). The densification, microstructure, and magnetic properties of the ferrite have been investigated and compared with those of ferrites produced by the traditional final-stage sintering process. It was found that the sample produced by a two-step sintering process with a high temperature of 1200 deg. C and a lower temperature of 1100 deg. C attained more than 96% of the theoretical density and had a uniform microstructure with a small average grain size. It also exhibited good performances in terms of permeability and Q-factor. Hence, this would seem to be an effective method for producing dense ferrites with a microstructure composed of small and even grains, which is a very effective strategy for improving the magnetic properties of ferrites.
Low pressure plasma reactors are important tools for ionized metal physical vapor deposition (IMPVD), a semiconductor plasma processing technology that is increasingly being applied to deposit Cu seed layers on semiconductor surfaces of trenches and vias with the high aspect ratio (e.g., >5:1). A large fraction of ionized atoms produced by the IMPVD process leads to an anisotropic deposition flux towards the substrate, a feature which is critical for attaining a void-free and uniform fill. Modeling such devices is challenging due to their high plasma density, reactive environment, but low gas pressure. A modular code developed by the Computational Optical and Discharge Physics Group, the Hybrid Plasma Equipment Model (HPEM), has been successfully applied to the numerical investigations of IMPVD by modeling a hollow cathode magnetron (HCM) device. However, as the development of semiconductor devices progresses towards the lower pressure regime (e.g., <5 mTorr), the breakdown of the continuum assumption limits the application of the fluid model in HPEM and suggests the incorporation of the kinetic method, such as the direct simulation Monte Carlo (DSMC), in the plasma simulation.The DSMC method, which solves the Boltzmann equation of transport, has been successfully applied in modeling micro-fluidic flows in MEMS devices with low Reynolds numbers, a feature shared with the HCM. Modeling of the basic physical and chemical processes for ion/neutral species in plasma have been developed and implemented in DSMC, which include ion particle motion due to the Lorentz force, electron impact reactions, charge exchange reactions, and charge recombination at the surface. The heating of neutrals due to collisions with ions and the heating of ions due to the electrostatic field will be shown to be captured by the DSMC simulations. In this work, DSMC calculations were coupled with the modules from HPEM so that the plasma can be self-consistently solved. Differences in the Ar results, the dominant species in the reactor, produced by the DSMC-HPEM coupled simulation will be shown in comparison with the original HPEM results. The effects of the DSMC calculations for ion/neutral species on HPEM plasma simulation will be further analyzed.
Perlite is an oversaturated, volcanic, glassy rock, which has chemically bound water from 2 to 5 wt%. Upon heating, perlite can be expanded up to 20 times of its original volume. Important applications are in the field of building industry, in refrigeration engineering or the pharmaceutical industry. As mineral filler in polymers, expanded perlite can increase the thermal conductivity, the viscosity and the mechanical properties of polypropylene composites. But there are still many challenges that must be analyzed to reach the full potential of those composites. This research work focuses on the morphology of expanded perlite/polypropylene (PP) compounds and the interactions between filler and polymer. To achieve good performance a homogenous dispersion of the filler in the polymer matrix is needed because the enhancement of the material correlates strongly with the morphology of the composite. Therefore it is necessary to characterize the microstructure of these materials in order to establish adequate structure-process-property relationships. The expanded perlite/PP composites were compounded with a co-rotating twin screw extruder Theysohn TSK 30/40D. For producing the closed cell expanded perlite a new technology, the bublon process, was used. For the material characterization two particles sizes were chosen and the filler content was varied at 5, 10 and 15 wt%. For the analysis of the effects of the screw geometry, two setups have been chosen for the processing of the materials. The produced materials were analyzed by scanning electron microscope (SEM) and tensile testing. The results show a reinforcement effect of the filler and differences in the inner structure of expanded perlite and in the morphology.