Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mix Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

USHPRR MP-1 Irradiation Test: Assessment of Edge Pitting and Bond Line Corrosion in Vendor Produced Fuel Plates

This report summarizes an effort to identify the source of anomalous localized edge pitting and bond line corrosive attack of experimental mini fuel plates manufactured at the commercial fuel vendor BWXT and tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) as part of the Miniplate 1 (MP-1) irradiation test. The MP-1 test was conducted by the US High Performance Research Reactor Project (USHPRR) and overseen by the Fuel Qualification Pillar (FQ). The test involved evaluation of a mix of 62 “vendor” fuel plates fabricated at BWXT and 12 “laboratory” fuel plates fabricated at Idaho National Laboratory using commercial-scale and labscale fabrication processes respectively. The MP-1 test was the first in a series of tests to generate data to support qualification of a new plate-type low-enriched uranium (LEU) U-10Mo monolithic fuel system. The major objective of the MP-1 experiment was to test, for the first time, miniplates fabricated by a commercial fuel vendor over the range of irradiation conditions relevant to conversion of NRC regulated High Performance Research Reactors (HPRRs) from high-enriched uranium to LEU. The focus of the efforts described in this report are the vendor fuel plates to inform changes in the fabrication process prior to fabrication of the next miniplate experiment MP2.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tank 27 Solids Disturbance Testing Using M-Star for the Impact of CSMP Usage on Blend Tank Mixing Effectiveness

Savannah River Mission Completion (SRMC) plans to operate Tank 27as a blend tank for future waste disposal operations. It is desirable to avoid additional worker exposure by using the planned commercial submersible mixing pump (CSMP) installations in Risers B2 and B4 to function as the blend pumps for prolonged blend tank operations. The purpose of this task is to evaluate the impacts to mixing across a range of pump installation heights from 1 to 201 inches above the tank floor. The CSMPs shall maintain adequate blending within a 24 hour maximum timeframe and an adequate nozzle discharge velocity as outlined in U-ESR-G-00030, using the specifications of the planned CSMPs listed in PO SRRA149971 and M-DS-G-00081. Specifications include: maximum pump diameter of D=22.5 in., dual nozzles placed tangentially opposed with nominal inside diameter of 2 in., total flow range (both nozzles combined) of 500 to 1950 GPM and maximum RPM of 1800. Tank 27 is expected to have a fill height maximum of 360". This analysis began by using results from the 2010 testing and applying them to the Tank 27 design to calculate a mixing time as a function of pump flow rate. These results were modified to account for the higher liquid level in Tank 27. Once the liquid level was increased to 360 inches, the results were modified to account for a higher viscosity in Tank 27 than in the testing. Once the viscosity was increased, the effect of changing pump elevation was applied to calculations of the mixing time in Tank 27. Finally, the uncertainty from the testing was included in the analysis to recommend a blend time as a function of pump flow rate and elevation. The conclusion from this study is that the particles in tank 27 will be suspended at both the 600 and 900 gpm flow rates. Only particles above 90 micron will not be suspended in significant amounts when the flow rate is 600 gpm. At 900 gpm even 100 micron particles were thoroughly suspended in the tank. From the series of simulations it has been concluded that it will not be possible to mix tank 27 at the proposed fluid flow rates and not suspend the solid particles at the bottom of the tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Treatment of fly ash for use in concrete

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

36 MATERIALS SCIENCE↗

CO.sub.2 utilization in electrochemical systems

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

36 MATERIALS SCIENCE↗

Terminal shock position and restart control of a Mach 2.7, two-dimensional, twin duct mixed compression inlet

Experimental results of terminal shock and restart control system tests of a two-dimensional, twin-duct mixed compression inlet are presented. High-response (110-Hz bandwidth) overboard bypass doors were used, both as the variable to control shock position and as the means of disturbing the inlet airflow. An inherent instability in inlet shock position resulted in noisy feedback signals and thus restricted the terminal shock position control performance that was achieved. Proportional-plus-integral type controllers using either throat exit static pressure or shock position sensor feedback gave adequate low-frequency control. The inlet restart control system kept the terminal shock control loop closed throughout the unstart-restart transient. The capability to restart the inlet was non limited by the inlet instability.

Cole, G. L.↗

Accelerating Laboratory-Based, All-Solid-State Battery Research and Development: Industrially Relevant Small-Batch Dry-Processing, Small and Low-Cost Test Fixtures, and Short-Tolerant Separators

This work presents improvements to mixing (for dry-processed electrodes), separator robustness, and cell testing jigs for all-solid-state batteries (ASSBs). These developments combine synergistically to enable rapid research and development of ASSB catholytes. A mechanical "kneader" is designed and built which emulates the mixing and fibrillation of poly-tetrafluoroethylene binder that occurs in industrially relevant twin-screw extruders. A modest improvement in the mixing and dispersion catholyte materials is observed using micro-resolution X-ray computed tomography (X-ray CT). Catholytes are paired with an In-metal anode and separated by a novel, dual-layer, polyaramid-fiber-supported, sulfide-solid electrolyte (Li6 PS5 Cl) separator. This separator achieves high short tolerance which enabled a 95% success rate across 20 attempted cells and to date over 100 successful cells have been built. ASSBs were tested in a 2032 coin-cell format. Simultaneous cycling of a large number of cells is further enabled by a compact and low cost (~ 38 USD per jig) pressure application jig of which 100 have been constructed to date. The utility of these advances is demonstrated through a brief study on the effect cathode-side conductive carbon and current collector type has on capacity and rate performance.

25 ENERGY STORAGE↗

A combined experimental and computational analysis of failure mechanisms in open-hole cross-ply laminates under flexural loading

In this work, integrated experimental tests and computational modeling are proposed to investigate the failure mechanisms of open-hole cross-ply carbon fiber reinforced polymer (CFRP) laminated composites. In particular, we propose two effective methods, which include width-tapered double cantilever beam (WTDCB) and fixed-ratio mixed-mode end load split (FRMMELS) tests, to obtain the experimental data more reliably. We then calibrate the traction-separation laws of cohesive zone model (CZM) used among laminas of the composites by leveraging these two methods. The experimental results of fracture energy, i.e. G Ic and G Tc , obtained from WTDCB and FRMMELS tests are generally insensitive to the crack length thus requiring no effort to accurately measure the crack tip. Moreover, FRMMELS sample contains a fixed mixed-mode ratio of G IIc /G Tc depending on the width taper ratio. Examining comparisons between experimental results of FRMMELS tests and failure surface of B–K failure criterion predicted from a curve fitting, good agreement between the predictions and experimental data has been found, indicating that FRMMELS tests are an effective method to determine mixed-mode fracture criterion. In addition, a coupled experimental-computational modeling of WTDCB, edge notched flexure, and FRMMELS tests are adopted to calibrate and validate the interfacial strengths. Finally, failure mechanisms of open-hole cross-ply CFRP laminates under flexural loading have been studied systematically using experimental and multi-scale computational analyses based on the developed CZM model. The initiation and propagation of delamination, the failure of laminated layers as well as load-displacement curves predicted from computational analyses are in good agreement with what we have observed experimentally.

36 MATERIALS SCIENCE↗

Investigation of the jet-wake flow of a highly loaded centrifugal compressor impeller

Investigations, aimed at developing a better understanding of the complex flow field in high performance centrifugal compressors were performed. Newly developed measuring techniques for unsteady static and total pressures as well as flow directions, and a digital data analysis system for fluctuating signals were thoroughly tested. The loss-affected mixing process of the distorted impeller discharge flow was investigated in detail, in the absolute and relative system, at impeller tip speeds up to 380 m/s. A theoretical analysis proved good coincidence of the test results with the DEAN-SENOO theory, which was extended to compressible flows.

Eckardt, D.↗

Near-field turbulence properties of single- and two-stream plane mixing layers

Detailed mean-flow and turbulence measurements have been made in the near-field of two plane mixing layers in air with a maximum velocity of 21 m/s. The experimental rig enabled mixing layers of velocity ratios 0 and 0.46 to be generated simultaneously. Cases with both tripped and untripped initial boundary layers were studied. In all cases, it was found that the two-stream layer developed to the self-preserving state in a distance much shorter than the single-stream layer which followed accepted criteria for the development distance. The asymptotic levels of the turbulence quantities in the two-stream layer, and the development of the single-stream layer showed agreement with existing data. The results suggest that the two-stream mixing layer should provide a better test case for the development of turbulence models and calculation methods than the single-stream mixing layer.

Mehta, R. D.↗

Mass spectrometric gas composition measurements associated with jet interaction tests in a high-enthalpy wind tunnel

Knowledge of test gas composition is important in wind-tunnel experiments measuring aerothermodynamic interactions. This paper describes measurements made by sampling the top of the test section during runs of the Langley 7-Inch High-Temperature Tunnel. The tests were conducted to determine the mixing of gas injected from a flat-plate model into a combustion-heated hypervelocity test stream and to monitor the CO2 produced in the combustion. The Mass Spectrometric (MS) measurements yield the mole fraction of N2 or He and CO2 reaching the sample inlets. The data obtained for several tunnel run conditions are related to the pressures measured in the tunnel test section and at the MS ionizer inlet. The apparent distributions of injected gas species and tunnel gas (CO2) are discussed relative to the sampling techniques. The measurements provided significant real-time data for the distribution of injected gases in the test section. The jet N2 diffused readily from the test stream, but the jet He was mostly entrained. The amounts of CO2 and Ar diffusing upward in the test section for several run conditions indicated the variability of the combustion-gas test-stream composition.

Lewis, B. W.↗

Ice Crystal Icing Physics Study using a NACA 0012 Airfoil at the National Research Council of Canada's Research Altitude Test Facility

This paper presents results from a study of the fundamental physics of ice-crystal ice accretion using a NACA 0012 airfoil at the National Research Council of Canada (NRC) Research Altitude Test Facility in August 2017. These tests were a continuation of work which began in 2010 as part of a joint collaboration between NASA and NRC. The research seeks to generate icing conditions representative of those that occur inside a jet engine when ingesting ice crystals. In this test, an airfoil was exposed to mixed-phase icing conditions and the resulting ice accretions were recorded and analyzed. This paper details the specific objectives, procedures, and measurements which included the aero-thermal and cloud measurements. The objectives were built upon observations and hypothesis generated from several previous test campaigns regarding mixed-phase ice-crystal icing. The specific objectives included (A) ice accretions under different wet-bulb temperatures, (B) investigations of steady-state ice shapes previously reported in the literature, (C) total water content variations in search of a threshold for accretion, and (D) probe characterization related to measuring melt fraction which is important to characterize the mixed-phase condition. The resulting ice accretions and conditions leading to such accretions are intended to help extend NASA’s predictive ice-accretion codes to include conditions occurring in engine ice-crystal icing.

Icing↗

Investigation of thermal hydraulic behavior of the High Temperature Test Facility's lower plenum via large eddy simulation

A high-fidelity computational fluid dynamics (CFD) analysis was performed using the Large Eddy Simulation (LES) model for the lower plenum of the High–Temperature Test Facility (HTTF), a ¼ scale test facility of the modular high temperature gas-cooled reactor (MHTGR) managed by Oregon State University. In most next–generation nuclear reactors, thermal stress due to thermal striping is one of the risks to be curiously considered. This is also true for HTGRs, especially since the exhaust helium gas temperature is high. In order to evaluate these risks and performance, organizations in the United States led by the OECD NEA are conducting a thermal hydraulic code benchmark for HTGR, and the test facility used for this benchmark is HTTF. HTTF can perform experiments in both normal and accident situations and provide high-quality experimental data. However, it is difficult to provide sufficient data for benchmarking through experiments, and there is a problem with the reliability of CFD analysis results based on Reynolds–averaged Navier–Stokes to analyze thermal hydraulic behavior without verification. To solve this problem, high-fidelity 3-D CFD analysis was performed using the LES model for HTTF. It was also verified that the LES model can properly simulate this jet mixing phenomenon via a unit cell test that provides experimental information. As a result of CFD analysis, the lower the dependency of the sub-grid scale model, the closer to the actual analysis result. In the case of unit cell test CFD analysis and HTTF CFD analysis, the volume-averaged sub-grid scale model dependency was calculated to be 13.0% and 9.16%, respectively. As a result of HTTF analysis, quantitative data of the fluid inside the HTTF lower plenum was provided in this paper. As a result of qualitative analysis, the temperature was highest at the center of the lower plenum, while the temperature fluctuation was highest near the edge of the lower plenum wall. The power spectral density of temperature was analyzed via fast Fourier transform (FFT) for specific points on the center and side of the lower plenum. FFT results did not reveal specific frequency-dominant temperature fluctuations in the center part. It was confirmed that the temperature power spectral density (PSD) at the top increased from the center to the wake. The vortex was visualized using the well-known scalar Q-criterion, and as a result, the closer to the outlet duct, the greater the influence of the mainstream, so that the inflow jet vortex was dissipated and mixed at the top of the lower plenum. Additionally, FFT analysis was performed on the support structure near the corner of the lower plenum with large temperature fluctuations, and as a result, it was confirmed that the temperature fluctuation of the flow did not have a significant effect near the corner wall. In addition, the vortices generated from the lower plenum to the outlet duct were identified in this paper. It is considered that the quantitative and qualitative results presented in this paper will serve as reference data for the benchmark.

97 MATHEMATICS AND COMPUTING↗

Operation and testing of Mark 10 Mod 3 underwater breathing apparatus

Performance tests on a closed circuit, mixed gas underwater breathing apparatus are reported. The equipment is designed to provide a minimum diving duration of four hours at 1500 ft below sea surface; it senses oxygen partial pressure in the breathing gas mix and controls oxygen content of the breathing gas within narrow limits about a preset value. The breathing circuit subsystem provides respirable gas to the diver and removes carbon dioxide and moisture from the expired gas. Test results indicate undesirable variations in oxygen partial pressure with oxygen addition and insufficient carbon dioxide absorption.

Milwee, W. I., Jr.↗

The effects of radiation on the interlaminar fracture toughness of a graphite/epoxy composite

An experimental study is made of the effect of electron irradiation (10 to the 10th rad), simulating a 30-year geosynchronous orbit exposure, on the fracture toughness of a graphite/epoxy composite, T300/934. The double cantilever beam (DBC) test is used to determine Mode I (peel) critical strain energy release rate and the edge delamination tension (EDT) test is used to determine mixed Mode I and II (peel and shear) critical strain energy release rate. It is found that the electron interaction of the epoxy matrix material enhances the fracture toughness properties of the composite and that the test temperature has a significant effect on the fracture toughness of both baseline and irradiated material.

Funk, J. G.↗

Design and Testing of a 10B4C Capsule for Spectral-Tailoring in Mixed-Spectrum Reactors

A boron carbide capsule highly enriched in 10B has been designed and used for spectral-tailoring experiments at the TRIGA reactor at Washington State University. New experiments show that enriching the boron to 96% B-10 results in additional absorption of neutrons in the resonance region thereby producing a neutron spectrum that is much closer to a pure 235U fission spectrum. A cadmium outer cover was used to reduce thermal heating. The neutron spectrum calculated with MCNP was found to be in very good agreement with measured activation rates from neutron fluence monitors.

boron carbide, neutron spectral-tailoring↗

Tests of C P T symmetry in B 0 - B ¯ 0 mixing and in B 0 → c c ¯ K 0 decays

Here, using the eight time dependences e- Γt (1 + C i cos Δmt + S i sin Δmt) for the decays Y(4S)→B 0 $\bar{B}$ 0 →f j f k , with the decay into a flavor-specific state f j = ± X before or after the decay into a CP eigenstate f k =c$\bar{c}$ K S,L , as measured by the BABAR experiment, we determine the three CPT-sensitive parameters Re(z) and Im(z) in B 0 $\bar{B}$ 0 mixing and |$\bar{A}$/A| in B 0 →c$\bar{c}$ K 0 decays. We find Im(z) = 0.010 ± 0.030 ± 0.013, Re(z) = -0.065 ± 0.028 ± 0.014, and |$\bar{A}$/A|=0.999±0.023±0.01, in agreement with CPT symmetry.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Predicting the Occurrence of Mixed Mode Failure Associated With Hydraulic Fracturing, Part 2 Water Saturated Tests

Seven water-saturated triaxial extension experiments were conducted on four sedimentary rocks. This experimental condition was hypothesized more representative of that existing for downhole hydrofracture and thus it may improve our understanding of the phenomena. In all tests the pore pressure was 10 MPa and confirming pressure was adjusted to achieve tensile and transitional failure mode conditions. Using previous work in this LDRD for comparison, the law of effective stress is demonstrated in extension using this sample geometry. In three of the four lithologies, no apparent chemo-mechanical effect of water is apparent, and in the fourth lithology test results indicate some chemo-mechanical effect of water.

58 GEOSCIENCES↗

Initial dynamic photoactive materials testing of an atmospheric chamber intended for radioactive and hazardous gases

Radioisotopes and hazardous gases can have undetermined environmental pathways. Researchers at Pacific Northwest National Laboratory constructed a chamber that complies with the requirements needed for an atmospheric reaction platform and the safety principles of interacting with hazardous dispersible sources to enable the environmental testing of these gases. Initial dynamic testing showed inter-chamber mixing completed from minutes to 1.5 hours. The photooxidation of butyl iodine showed the presence of signals from reaction products, and intermediaries for up to 50 hours. Current detection limits of the chamber and analytical collection and testing approach were shown to be in the single-digit parts per billion levels. In conclusion, the comparisons between the measured oxidation trends and literature show the utility of performing laboratory experiments to validate the results of modeling for larger-scale scenarios.

54 ENVIRONMENTAL SCIENCES↗