Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modal Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Treatment of the control mechanisms of light airplanes in the flutter clearance process

It has become more and more evident that many difficulties encountered in the course of aircraft flutter analyses can be traced to strong localized nonlinearities in the control mechanisms. To cope with these problems, more reliable mathematical models paying special attention to control system nonlinearities were established by means of modified ground vibration test procedures in combination with suitably adapted modal synthesis approaches. Three different concepts are presented.

Breitbach, E. J.↗

Close-mode identification performance of the ITD algorithm

Results of Monte Carlo numerical simulations conducted to study the close-mode performance of the Ibrahim Time-Domain (ITD) modal identification algorithm are presented. The ITD technique is a matrix eigensolution method for obtaining structural modal parameters directly from free-response test data without using the FFT. Thus, the well-known resolution and leakage limitations of the FFT procedure, that are particularly significant with short records, are avoided. As an example, one of several experimental data analyses where close modes have been accurately identified using very short records is shown. Although the identification scatter is found to increase as the square of reductions in frequency separation at small separations, the ability to differentiate modes spaced at fractions of the FFT resolution is substantiated.

Pappa, R. S.↗

Ground vibration test of an F-16 airplane with modified decoupler pylons

The decoupler pylon is a passive wing/store flutter suppression device. It was modified to reduce friction following initial flight tests. A ground vibration test was conducted on an F-16 aircraft loaded on each wing with a one-half-full (center bay empty) 370-gallon fuel tank mounted on a standard pylon, a GBU-8 store mounted on the decoupler pylon, and an AIM-9J missile mounted on a wingtip launcher. The test was conducted prior to flight tests with the modified pylon to determine modal frequencies, mode shapes, and structural damping coefficients. Data presented include frequency response plots, mode shape plots, and limited force-effect plots.

Cazier, F. W., Jr..↗

Turbofan aft duct suppressor study. Contractor's data report of mode probe signal data

Acoustic modal distributions were measured in a fan test model having an annular exhaust duct for comparison with theoretically predicted acoustic suppression values. This report contains the amplitude and phase data of the acoustic signals sensed by the transducers of the two mode probes employed in the measurement. Each mode probe consisted of an array of 12 transducers sensing the acoustic field at three axial positions and four radial positions.

Fiske, G. H.↗

A summary of recent NASA/Army contributions to rotorcraft vibrations and structural dynamics technology

The requirement for low vibrations has achieved the status of a critical design consideration in modern helicopters. There is now a recognized need to account for vibrations during both the analytical and experimental phases of design. Research activities in this area were both broad and varied and notable advances were made in recent years in the critical elements of the technology base needed to achieve the goal of a jet smooth ride. The purpose is to present an overview of accomplishments and current activities of govern and government-sponsored research in the area of rotorcraft vibrations and structural dynamics, focusing on NASA and Army contributions over the last decade or so. Specific topics addressed include: airframe finite-element modeling for static and dynamic analyses, analysis of coupled rotor-airframe vibrations, optimization of airframes subject to vibration constraints, active and passive control of vibrations in both the rotating and fixed systems, and integration of testing and analysis in such guises as modal analysis, system identification, structural modification, and vibratory loads measurement.

Kvaternik, Raymond G.↗

Teleoperator comfort and psychometric stability: Criteria for limiting master-controller forces of operation and feedback during telemanipulation

The following question is addressed: How much force should operators exert, or experience, when operating a telemanipulator master-controller for sustained periods without encountering significant fatigue and discomfort, and without loss of stability in psychometric perception of force. The need to minimize exertion demands to avoid fatigue is diametrically opposed by the need to present a wide range of force stimuli to enhance perception of applied or reflected forces. For 104 minutes subjects repetitiously performed a series of 15 s isometric pinch grasps; controlled at 5, 15, and 25 percent of their maximum voluntary strength. Cyclic pinch grasps were separated by rest intervals of 7.5 and 15 s. Upon completion of every 10 minute period, subjects interrupted grasping activities to gage the intensity of fatigue and discomfort in the hand and forearm using a cross-modal matching technique. A series of psychometric tests were then conducted to determine accuracy and stability in the subject's perception of force experienced. Results showed that onset of sensations of discomfort and fatigue were dependent upon the magnitude of grasp force, work/rest ratio, and progression of task. Declines in force magnitude estimation slopes, indicating a reduction in force perception sensitivity, occurred with increased grasp force when work/rest ratios were greater than 1.0. Specific recommendations for avoiding discomfort and shifts in force perception, by limiting pinch grasp force required for master-controller operation and range of force reflection or work/rest ratios, are provided.

Wiker, Steven F.↗

Eigenvalue error analysis of viscously damped structures using a Ritz reduction method

The efficient solution of the eigenvalue problem that results from inserting passive dampers with variable stiffness and damping coefficients into a structure is addressed. Eigenanalysis of reduced models obtained by retaining a number of normal modes augmented with Ritz vectors corresponding to the static solutions resulting from the load patterns introduced by the dampers has been empirically shown to yield excellent approximations to the full eigenvalue problem. An analysis of this technique in the case of a single damper is presented. A priori and a posteriori error estimates are generated and tested on numerical examples. Comparison theorems with modally truncated models and a Markov parameter matching reduced-order model are derived. These theorems corroborate the heuristic that residual flexibility methods improve low-frequency approximation of the system. The analysis leads to other techniques for eigenvalue approximation. Approximate closed-form solutions are derived that include a refinement to eigenvalue derivative methods for approximation. An efficient Newton scheme is also developed. A numerical example is presented demonstrating the effectiveness of each of these methods.

Chu, Cheng-Chih↗

Variable Stiffness Spar Wind-Tunnel Model Development and Testing

The concept of exploiting wing flexibility to improve aerodynamic performance was investigated in the wind tunnel by employing multiple control surfaces and by varying wing structural stiffness via a Variable Stiffness Spar (VSS) mechanism. High design loads compromised the VSS effectiveness because the aerodynamic wind-tunnel model was much stiffer than desired in order to meet the strength requirements. Results from tests of the model include stiffness and modal data, model deformation data, aerodynamic loads, static control surface derivatives, and fuselage standoff pressure data. Effects of the VSS on the stiffness and modal characteristics, lift curve slope, and control surface effectiveness are discussed. The VSS had the most effect on the rolling moment generated by the leading-edge outboard flap at subsonic speeds. The effects of the VSS for the other control surfaces and speed regimes were less. The difficulties encountered and the ability of the VSS to alter the aeroelastic characteristics of the wing emphasize the need for the development of improved design and construction methods for static aeroelastic models. The data collected and presented is valuable in terms of understanding static aeroelastic wind-tunnel model development.

Florance, James R.↗

Satellite-Derived Imagery and Transfer Learning: A Novel Technique for Land Cover Classification

Land cover classification is a continuing research topic due to its relevance to land use and land cover changes from impacts such as climate change, agriculture, urbanization, and hazardous weather. Simple access to frequently changing land cover classifications could provide knowledge and decision support to various researchers and agencies across the globe for each of above-mentioned and related influences. This research aims to provide a novel technique for land cover classification of remote sensing imagery; harnessing Artificial Neural Networks and transfer learning (TL). Knowledge sharing techniques within machine learning are typically utilized when training datasets are sparse or transitions between data modalities is required. In this case, two data modalities, multi and hyperspectral data, are considered for knowledge transfer. The large number of continuous spectral bands available from hyperspectral sensors typically provide increased sophisticated land classification capability compared to more traditional multispectral imagery with limited discrete spectral bands. However, large-scale, frequent access to hyperspectral imagery is relatively limited. The proposed classification technique would therefore prove useful in regions in which hyperspectral data are not readily available for classification but multispectral data are. Image segmentation models are trained on each multi and hyperspectral datasets. Knowledge sharing techniques are then applied to each model to understand what knowledge, if any, is gained when moving between the data modalities. The datasets utilized for training and testing a U-Net model include the European Space Agency’s multispectral imager Sentinel-2 and the hyperspectral German Aerospace Center’s Earth Sensing Imaging Spectrometer (DESIS). Initially, only two classes, land and water, are classified for simplicity. However, more complex classes can be added if knowledge sharing is successful. The workflow for image classification through supervised image segmentation with a U-Net model will be discussed along with metrics calculated before and after TL for both Sentinel-2 and DESIS data are applied. Additionally, future steps to advance the sophistication of this technique as well as other applicable methodologies will be explored.

Emily Foshee↗

Precision Pointing Improvements for the Lunar Reconnaissance Orbiter Camera

The Lunar Reconnaissance Orbiter (LRO) was launched in 2009 and, with its seven science instruments, continues to make remarkable discoveries of the Moon. LRO is in a slightly elliptical, polar lunar orbit and nominally maintains a nadir orientation. In early 2018, the Miniature Inertial Measurement Unit (MIMU) was powered off following a fairly rapid decline in the laser intensity on the X axis. An algorithm combining star tracker quaternion differentiated rates and integrated control torque commands in a complementary filter, now provides the onboard rate estimate, replacing the MIMU. One of the science instruments, the LRO Camera(LROC) system, contains a Wide Angle Camera (WAC) and two Narrow Angle Cameras (NAC). The NACs suffer from larger attitude drifts during imaging of the Moon for stereo image processing, resulting from pointing stability degradation of the star tracker derived rates. The controller gains and structural filter were redesigned to attenuate the new disturbances while also maintaining adequate stability and modal suppression. This paper documents the development, testing, and operational implementation of the revised control system parameters, specifically targeted for use during LROC imaging. The new parameters improved pointing performance for LROC.

Julie Halverson↗

Modal characteristics of a stiffened composite cylinder with open and closed end conditions

The structural and acoustic modal frequencies and the loss factors of a composite fuselage model under free-free end and support-end conditions are evaluated. The fuselage model is a composite filament wound, cylindrical structure composed of carbon fibers embedded in an epoxy resin and has a ply orientation of +,-45, +,-32, 0, -,+32, and -,+45. A computer aided test system was utilized to obtain resonance frequencies, modal damping, and mode shape coefficients. Sound pressure and phase survey data are utilized to estimate acoustic modal freuencies and reverberation time was measured to calculate the acoustic loss factors. The derived structural and acoustic modal parameters are compared to analytical data from a computer prediction model. The data reveal that the acoustic modal frequencies and mode shape correlate well with predicted data, and there is fair agreement between structural modal frequencies and mode shape for the two data sets.

Grosveld, F. W.↗

Estimation of Modal Parameters Using a Wavelet-Based Approach

Modal stability parameters are extracted directly from aeroservoelastic flight test data by decomposition of accelerometer response signals into time-frequency atoms. Logarithmic sweeps and sinusoidal pulses are used to generate DAST closed loop excitation data. Novel wavelets constructed to extract modal damping and frequency explicitly from the data are introduced. The so-called Haley and Laplace wavelets are used to track time-varying modal damping and frequency in a matching pursuit algorithm. Estimation of the trend to aeroservoelastic instability is demonstrated successfully from analysis of the DAST data.

Lind, Rick↗

Model updating based on sensitivities of system matrices

A new approach, which allows the physical parameters to be adjusted and preserves the structural connectivity condition, is developed in this paper. This approach is based on the sensitivities of the mass and stiffness matrices with respect to physical parameters in an attempt to use test data to correct the analytical model. The analytical mass and stiffness matrices can be corrected simultaneously. The modal data of the updated model dramatically converges to that of the test model. A numerical example is presented to illustrate the feasibility of this approach. Comparisons with the other methods are also given.

Huang, Hsin-Hsen↗

A modal separation measurement technique for broadband noise propagating inside circular ducts

A measurement technique which separates broadband noise propagating inside circular ducts into the acoustic duct modes is developed. The technique is also applicable to discrete frequency noise. The acoustic modes are produced by weighted combinations of the instantaneous outputs of microphones spaced around the duct circumference. The technique is compared with the cross spectral density approach presently available and found to have certain advantages, and disadvantages. Considerable simplification of both the new technique and the cross spectral density approach occurs when no correlation exists between different circumferential mode orders. The properties leading to uncorrelated modes and experimental tests which verify this condition are discussed. The modal measurement technique is applied to the case of broadband noise generated by flow through a coaxial obstruction (nozzle or orifice) in a pipe. Different circumferential mode orders are shown to be uncorrelated for this type of noise source.

Kerschen, E. J.↗

Required developments in structural dynamics

The finite element method, modal component synthesis, and the use of fast Fourier transformation were key developments in structural dynamics in the past 15 to 20 years. Current areas requiring additional effort include: (1) the correct calculation of modal shape and natural frequencies for complex structures; (2) the correlation of math models with test data; (3) the establishment of a criteria for "goodness" of the correlation between analysis and test; (4) the selection of the correct displacement functions when using computer programs for modal synthesis; (5) accuracy of response calculations; and (6) the inverse problem of determining the force problem from the response data. Trends identified include the use of distributed computing, greater reliance on analysis, and the possible use of artificial intelligence techniques, or some way of feeding back information, to provide solution guidance to engineers.

Wada, B. K.↗

Thermal Vacuum Testing of ICPTA RCS at Plum Brook B-2

Vacuum and thermal vacuum testing of the Integrated Cryogenic Propulsion Test Article (ICPTA) was performed at the Plum Brook B-2 facility as a part of a system checkout and facility characterization effort. Multiple test objectives included: integrated Reaction Control System (RCS) characterization, cold helium pressurization system characterization, modal propellant gaging experiment (Orion), CFM propellant loading experiments, main engine characterization. The ICPTA is a test bed for LOX/LCH4 technologies built in 2016 using new components and hardware from the former Morpheus vehicle and other projects.

Atwell, M. J.↗

Method for Real-Time State Estimation of Structural Modes for an Aeroelastic Wind Tunnel Model

A method for estimating displacements, velocities, and accelerations of structural modes in generalized coordinates from measured sensor data in real time is developed and demonstrated. Data from conventional strain gauges and fiber optic strain sensors (FOSS) were combined with strain mode shapes to produce least-squares estimates of the structural mode displacements. Similarly, accelerometer data were combined with displacement mode shapes to estimate structural mode accelerations. Estimates were then combined using a Kalman filter to refine the displacement estimates and produce structural mode velocity estimates. The approach was demonstrated using simulation data for the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project in both a stable open-loop condition and an unstable condition where estimated displacement and velocity states were used for feedback control. Results supported the feasibility of using this approach for feedback control and system identification applications for wind tunnel tests.

Aeroservoelasticity↗

Single-Mode Projection Filters for Modal Parameter Identification for Flexible Structures

Single-mode projection filters are developed for eigensystem parameter identification from both analytical results and test data. Explicit formulations of these projection filters are derived using the orthogonal matrices of the controllability and observability matrices in the general sense. A global minimum optimization algorithm is applied to update the filter parameters by using the interval analysis method. The updated modal parameters represent the characteristics of the test data. For illustration of this new approach, a numerical simulation for the MAST beam structure is shown by using a one-dimensional global optimization algorithm to identify modal frequencies and damping. Another numerical simulation of a ten-mode structure is also presented by using a two-dimensional global optimization algorithm to illustrate the feasibility of the new method. The projection filters are practical for parallel processing implementation.

Huang, Jen-Kuang↗