Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Modeling and Analysis of a Heat Pump Clothes Dryer with Thermal Energy Storage

Clothes drying is an energy-intensive process that causes significant electricity consumption and carbon emissions in the US. Approximately 83% of Households in the US own a tumble clothes dryer at home and 80% of dryers are electrical resistance dryers with low energy efficiency. Heat pump technology makes it possible for highly efficient and clean drying. Additionally, the ventless design of heat pump clothes dryers (HPCD) provides more installation flexibility. HPCD involves three primary mediums: wet clothes, a closed air loop, and a refrigerant circuit. The evaporator is used to dehumidify the wet air and the condenser is used to re-heat the dry air. One of the critical technological barriers to HPCD market penetration is its long drying time, primarily due to the relatively low discharging temperature and the slow response during the warm-up period. In this study, the thermal energy storage (TES) technology is adopted to address this challenge by providing pre-heating of air prior to the condenser to increase the operating temperature of the process air. The heat pump will charge the phase change material (PCM) in the TES device with heating energy during clothes washing and the PCM will discharge the stored heat to facilitate air heating during clothes drying. To analyze the optimal design and potential for energy saving and drying time reduction, a mathematical model of the HPCD system was developed. The HPCD is a highly dynamic system with a coupled heat and mass transfer and heat pumping cycle. This paper provides solutions to simulate the transient behavior of the system while maintaining low computational cost. The modeling result indicates reduced energy consumption and drying time by integrating TES with HPCD, as compared to electrical resistance dryers. The study can provide significant insights into improving building flexibility with TES and smart appliances.

Liu, Xiaoli↗
DOE OSTI2024

CO 2 storage site characterization using ensemble-based approaches with deep generative models

Estimating spatially distributed properties such as permeability from available sparse measurements is a great challenge in efficient subsurface CO 2 storage operations. In this paper, a deep generative model that can accurately capture complex subsurface structure is tested with an ensemble-based inversion method for accurate and accelerated characterization of CO 2 storage sites. We chose Wasserstein Generative Adversarial Network with Gradient Penalty (WGAN-GP) for its realistic reservoir property representation and Ensemble Smoother with Multiple Data Assimilation (ES-MDA) for its robust data fitting and uncertainty quantification capability. WGAN-GP are trained to generate high-dimensional permeability fields from a low-dimensional latent space and ES-MDA then updates the latent variables by assimilating available measurements. Several subsurface site characterization examples including Gaussian, channelized, and fractured reservoirs are used to evaluate the accuracy and computational efficiency of the proposed method and the main features of the unknown permeability fields are characterized accurately with reliable uncertainty quantification. Furthermore, the estimation performance is compared with a widely-used variational, i.e., optimization-based, inversion approach, and the proposed approach outperforms the variational inversion method in several benchmark cases. We explain such superior performance by visualizing the objective function in the latent space: because of nonlinear and aggressive dimension reduction via generative modeling, the objective function surface becomes extremely complex while the ensemble approximation can smooth out the multi-modal surface during the minimization. This suggests that the ensemble-based approach works well over the variational approach when combined with deep generative models at the cost of forward model runs unless convergence-ensuring modifications are implemented in the variational inversion.

42 ENGINEERING↗
DOE OSTI2024

Electrified Operando -Freezing of Electrocatalytic CO 2 Reduction Cells for Cryogenic Electron Microscopy

The ability to freeze and stabilize reaction intermediates in their metastable states and obtain their structural and chemical information with high spatial resolution would be very powerful to unravel the fundamentals in many important materials technologies such as catalysis and batteries. Here, we develop an electrified operando-freezing methodology for the first time to preserve these metastable states under electrochemical reaction conditions for cryogenic electron microscopy (cryo-EM) imaging and spectroscopy. Using Cu catalysts for CO 2 reduction as a model system, we observe restructuring of the Cu catalyst in a CO 2 atmosphere while the same catalyst remains intact in an air atmosphere at the nanometer scale. Furthermore, we discover the existence of single valance Cu (1+) state and C-O bonding at the electrified liquid-solid interface of the operando-frozen samples, which are key reaction intermediates that traditional ex situ measurements fail to detect. Finally, this work highlights our novel technique to study the local structure and chemistry of electrified liquid-solid interfaces, which has broad impact for many electrochemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1990

Effect of tail size reductions on longitudinal aerodynamic characteristics of a three surface F-15 model with nonaxisymmetric nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of horizontal and vertical tail size reductions on the longitudinal aerodynamic characteristics of a modified F-15 model with canards and 2-D convergent-divergent nozzles. Quantifying the drag decrease at low angles of attack produced by tail size reductions was the primary focus. The model was tested at Mach numbers of 0.40, 0.90, and 1.20 over an angle of attack of -2 degree to 10 degree. The nozzle exhaust flow was simulated using high pressure air at nozzle pressure ratios varying from 1.0 (jet off) to 7.5. Data were obtained on the baseline configuration with and without tails as well as with reduced horizontal and/or vertical tail sizes that were 75, 50, and 25 percent of the baseline tail areas.

Frassinelli, Mark C.↗
DOE OSTI2026

Pore-Scale Transport Effects in Electrochemical CO 2 Reduction on Gold via Coupled Microkinetic-Transport Modeling

A pore-resolved modeling framework is developed to quantify how pore-scale transport affects the intrinsic microkinetics of CO 2 -to-CO on Au. A DFT-informed microkinetic model is coupled self-consistently to a Generalized-Modified Poisson–Nernst–Planck (GMPNP) transport description in a single, electrolyte-filled cylindrical pore, allowing local concentrations and potential to feed back into site-specific reaction rates. FIB-SEM is used to determine pore sizes within realistic electrode materials. Across pore diameters, d p = 10–6000 nm, the surface-averaged CO 2 reduction rate is systematically reduced relative to the ideal microkinetic baseline where mass transport is not accounted for; the effectiveness factor 𝜂 𝑠,CO 2 , which quantifies this ratio, decreases rapidly at more negative potentials and is about 1% near −1.0 V vs SHE due to reactant depletion. Spatial maps reveal pore-bulk alkalization that emerges at higher cathodic bias, with a small, near-wall pH dip due to electrostatic repulsion of hydroxide at the cathode interface. For a fixed aspect ratio L p /d p , narrower pores exhibit larger 𝜂 𝑠,CO 2 by shortening diffusion paths, whereas variations in the aspect ratio L p /d p play a secondary role. A dimensionless analysis (surface/bulk Damköhler numbers) delineates operating regimes. In conclusion, this work offers a concept for incorporating microkinetic models into homogenized porous-electrode models through effectiveness factors and pore-size distribution.

Au-catalyst↗
DOE OSTI2025

Pseudo-viscous modeling of transport in dense granular flows for thermal energy storage applications

Dense, granular flows were examined to effectively capture and model bulk viscous properties in thin packed beds. A modified Couette cell with particle image velocimetry was used to experimentally determine pseudo-viscosity properties of four particulate media with varying morphologies: (1) iron oxide-coated SiO 2 particles, (2) CARBOBEAD CP30-60 particles, (3) CARBOBEAD CP40-100 particles, and (4) Al 2 O 3 beads. The pseudo-viscosity functions were fitted using a power law to correlate the measured shear stress as a function of measured shear rate. The pseudo-viscous functions were used as inputs to computation fluid dynamics models for a single-phase viscous fluid to predict granular flow profiles. Steady-state free surface velocity profiles at angular velocities <7 rad/s predicted by the model were in good agreement with the experimental particle image velocimetry measurements, resulting in Pearson correlation coefficients of 0.97 for iron-oxide coated SiO 2 particles and 0.95 for CP30-60 particles. As a result, this alternative approach to measuring pseudo-viscous properties under shearing and modeling bulk transport behavior of granular flow using computation fluid dynamics model offered significant reduction in computational load compared to discrete element methods.

14 SOLAR ENERGY↗
DOE OSTI2025

EPR and 31 P ENDOR Characterization of Pseudo-Jahn–Teller Dynamics and N 2 Activation in Functional Nitrogenase Models, P 3 E M(N 2 ) (M = Fe, Co; E = Si, B, C)

Here, the nominally trigonal, pseudo-Jahn-Teller (PJT)-active, S = ½ N 2 -bound transition-metal complexes, P 3 E M(N 2 ), M = Fe, Co, with three in-plane phosphine-ligands and axial donors, E = Si, B, C, include functional nitrogenase models that catalyze reduction of N 2 to NH 3 . We applied EPR, 31 P ENDOR spectroscopy and DFT computations to characterize the PJT-induced distortions of four selected P 3 E M(N 2 ), revealing how the metal-ion and axial ligand E together tune both PJT dynamics and N 2 activation for reduction. Comparisons reveal an unrecognized correlation between PJT distortion, M-E bond elasticity, and N 2 activation, providing guidelines for designing bioinspired N 2 -reduction catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

p K a of alcohols dictates their reactivity with reduced uranium-substituted thiomolybdate clusters

The uranium-substituted thiomolybdate cluster, (Cp* 3 Mo 3 S 4 )UCp*, has been demonstrated as a model for water reduction by single uranium atoms supported on a molybdenum sulfide surface (U@MoS 2 ). In this study, the scope of O–H bond activation is expanded through the investigation of the reactivity of various alcohols with differing pKa values for the –OH proton. The reaction of (Cp* 3 Mo 3 S 4 )UCp* with stoichiometric amounts of methanol, phenol, 2,6-dichlorophenol, and nonafluoro-tert-butyl alcohol affords the corresponding mono-alkoxide species, (Cp* 3 Mo 3 S 4 )Cp*U(OR), via a uranium-metalloligand cooperative activation of the O–H bond. This observed reactivity is analogous to the O–H bond activation reported by (Cp* 3 Mo 3 S 4 )UCp* in the presence of water. However, addition of tert-butanol induces protonolysis of the Cp* ligand on uranium, resulting in the formation of a uranium tris-tert-butoxide cluster, (Cp* 3 Mo 3 S 4 )U(O t Bu) 3 . Independent synthesis of (Cp* 3 Mo 3 S 4 )Cp*U(O t Bu) was possible via an alternative pathway, eliminating sterics as a justification for the observed discrepancy in reactivity. Furthermore, these results offer insight into the role the –OH proton pKa plays in dictating the mechanism of O–H bond activation of alcohols by the uranium-substituted thiomolybdate cluster.

Patra, Kamaless↗
DOE OSTI2025

Measurements of radial neutral density profiles from Balmer- α emission in Wendelstein 7-X

Radial neutral density profiles are estimated from measurements of passive H α emission in the Wendelstein 7-X stellarator. To parametrize the generally three-dimensional distribution with a low number of degrees of freedom, the neutral density is reduced to a flux surface quantity. Accounting for emission from excitation and recombination processes, neutral density profiles are derived independently for each of the available lines of sight. Density profiles obtained from the different viewing geometries are found to vary within one order of magnitude. Toroidally oriented lines of sight predict systematically lower neutral densities when compared to poloidally oriented ones. This discrepancy is attributed to the simplifications inherent in the imposed model and significant differences in integration volumes across the viewing geometries. In line with expectations, obtained neutral densities are found to decrease with increasing plasma density. Key restrictions of the model include the reduction of the neutral density to a flux surface quantity, uncertainties in the plasma profiles and instrument function, and line integration effects outside the last closed flux surface.

Wendelstein 7-X↗
DOE OSTI2026

Progressing Analysis of Variable Electric Rates (PAVER) Study

The Progressing Analysis of Variable Electric Rates (PAVER) study analyzed the impact of a range of time-varying electric rates on the performance of a regional electric grid and the resulting costs for participating and non-participating customers. This analysis leveraged and extended the work of PNNL’s Distribution System Operator with Transactive (DSO+T) study. Five different rate designs were included: a flat volumetric energy charge, a typical Time of Use (TOU) rate, a dynamic energy (DE) rate (based on wholesale locational marginal prices), a dynamic energy and capacity (DE+C) rate, and, finally, a Block and Swing (B&S) rate that billed customers based on their average load profile at constant pricing, but used the DE+C dynamic price for load deviations from their average profile. These rates were analyzed in a large-scale co-simulation of an entire regional grid with a customer population representative of the current state. A large fraction (80%) of residential and commercial customers were assumed to participate in these time-varying rates with automatically controlled HVAC, water heaters, electric vehicles, and batteries. This study assumed no industrial sector participation. The DE and DE+C rates saw system peak loads reduced by 6-7%, while the large participation in the TOU rate case saw a significant rebound effect and a resulting peak load increase of >5%. The impacts to the annual and peak system demand impacted system wholesale prices and the overall grid operating costs. This cost structure determined the revenue needed to be collected from customers by each rate design. Participating customers on the DE and DE+C rates (located in one of the modeled DSOs) saw reductions in average annual electricity bills of 11-17% with average increases in monthly bill variation of no more than 13%. At such high participation levels, TOU customers saw 10% higher average annual bills (due to system-wide rebound effects) and average increased monthly bill variation of 16%. Residential owners of large flexible loads (such as electric vehicles) saw larger bill savings (17-20%) when on a fully dynamic rate. The presence of on-site generation (such as rooftop solar) did not appear to appreciably change customer outcomes. Customers on the Block and Swing rate did see 6% lower monthly bill variation (as intended) than the flat rate case, but at the expense of appreciable bill savings, which were only 3%, comparable to the savings seen by non-participants. Given this finding we recommend that additional research be conducted into how best various bill protection mechanisms can balance minimizing customer bill variation with providing financial incentives commensurate with the flexibility customers provide. We also recommend that customer outcomes be explored across a range of regions using current actual customer and system cost data.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1973

The figure of Mars and its effect on radar-ranging.

Formulae are given which indicate the errors made in computing the radar-range to a planet when one assumes the planet to have a spherical surface, centered at the center of mass. These formulae are evaluated for Mars, using an ellipsoidal fit of the martian surface obtained from the occultation measurements of the Mariner 9 spacecraft. The secularlike part of the errors amounts to about 4 km in range over the past 3 oppositions, due mainly to the flattening of 0.006 and to a 3 km southerly displacement of the center of figure from the center of mass. The method of solution is given in the appendix along with a method for applying the ellipsoidal model to the reduction of radar-range data.

Standish, E. M., Jr.↗
NASA NTRS1978

Measurements of acoustic sources in motion

Results of the far-field pressures measured from three different types of moving sources are presented. These acoustic sources consist of a point monopole, a small model jet, and an aircraft. Results for the pressure time history produced by the point source show good agreement with those predicted analytically. Both actual and simulated forward motion of the model jet show reductions in noise levels with forward speed at all angles between the source and observer. Measurement with the aircraft over both an anechoic floor and over the ground yields a method for evaluating the transfer function for ground reflections at various angles between the moving aircraft and measurement position.

Maestrello, L.↗
NASA NTRS1979

Experimental measurements of moving noise sources

The far-field pressure was measured from three different types of moving sources: a point monopole, a small model jet, and an aircraft. Results for the pressure time history produced by the point source show good agreement with those predicted analytically. Both actual and simulated forward motion of the model jet show reductions in noise levels with forward speed at all angles between the source and observer. Measurement with the aircraft over both an anechoic floor and over the ground yields a method for evaluating the transfer function for ground reflections at various angles between the moving aircraft and measurement position.

Maestrello, L.↗
NASA NTRS1980

Instant-replay data system for combustion tests

A portable, inexpensive, easily programmed, and flexible pressure measuring and display system is described and evaluated in a multi-port combustion model. The data reduction system consists of a desk-top graphics display system and calculator with data tape storage and standard data communications interfacing capabilities, while a hard copy unit provides a permanent record of all plots and tables. The system offers the advantages of recording and comparing a large number of pressures at high data rates along with the display of the results in a meaningful graphical form for near real time analysis. Some discussion of combustor and engine experiments are included as examples of the data system application.

Trexler, C. A.↗
NASA NTRS1984

Economic impact of fuel properties on turbine powered business aircraft

The principal objective was to estimate the economic impact on the turbine-powered business aviation fleet of potential changes in the composition and properties of aviation fuel. Secondary objectives include estimation of the sensitivity of costs to specific fuel properties, and an assessment of the directions in which further research should be directed. The study was based on the published characteristics of typical and specific modern aircraft in three classes; heavy jet, light jet, and turboprop. Missions of these aircraft were simulated by computer methods for each aircraft for several range and payload combinations, and assumed atmospheric temperatures ranging from nominal to extremely cold. Five fuels were selected for comparison with the reference fuel, nominal Jet A. An overview of the data, the mathematic models, the data reduction and analysis procedure, and the results of the study are given. The direct operating costs of the study fuels are compared with that of the reference fuel in the 1990 time-frame, and the anticipated fleet costs and fuel break-even costs are estimated.

Powell, F. D.↗
NASA NTRS1986

A compressive failure model for anisotropic plates with a cutout under compressive and shear loads

The paper introduces a failure model for laminated composite plates with a cutout under combined compressive and shear loads. The model is based on kinking failure of the load-carrying fibers around a cutout, and includes the effect of local shearing and compressive stresses. Comparison of predictions of the model with available experimental results for quasi-isotropic and orthotropic plates with a circular hole indicated a good agreement. Predictions for orthotropic plates under combined loading are compared with the predictions of a point-stress model. The present model indicates significant reductions in axial load-carrying capacity due to shearing loads for plates with principal axis of orthotropy oriented along the axial load direction. A gain in strength is achieved by rotating the axis of orthotropy to counteract the shearing stress, or by eliminating the compressive-shear deformation coupling.

Gurdal, Z.↗
NASA NTRS1986

The role of damage-softened material behavior in the fracture of composites and adhesives

Failure mechanisms of materials under very high strains experienced at and ahead of the crack tip such as formation, growth, and interaction of microvoids in ductile materials, microcracks in brittle solids or crazes in polymers and adhesives are represented by one-dimensional, nonlinear stress-strain relations possessing different ways by which the material loses capacity to carry load up to fracture or total separation. A double cantilever beam (DCB) type specimen is considered. The nonlinear material is confined to a thin strip between the two elastic beams loaded by a wedge. The problem is first modeled as a beam on a nonlinear foundation. The pertinent equation is solved numerically as a two-point boundary value problem for both the stationary and the quasi-stationay propagating crack. A finite element model is then used to model the problem in more detail in order to assess the adequacy of the beam model for the reduction of experimental data to determine in-situ properties of the thin interlayer.

Ungsuwarungsri, T.↗
NASA NTRS1987

Superluminal motion in the double-lobed quasar 3C 245

VLBI observations of 3C 245 obtained at 10.7 GHz with the Mark III array at five epochs in 1981-1986 are reported. The data-reduction and model-fitting procedures are explained, and the results are presented in tables, graphs, and maps along with previously published data on 11 other superluminal sources. The central component of the quasar is found to have an apparent transverse velocity of (3.1 + or - 1.4) c/h, assuming H0 = 100h km/s Mpc and q0 = 0.5. From the apparent source orientation (based on R, variability, apparent curvature, and projected linear size) it is inferred that the apparent transverse velocity is anticorrelated with the angle to the line of sight, as predicted by relativistic-beaming models of superluminal motion.

Hough, D. H.↗