Search NASA⌕ Search

SEARCH · Search NASA

Results for “Module manufacturing,”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Cool covered sky-splitting spectrum-splitting FK

Placing a plane mirror between the primary lens and the receiver in a Fresnel Köhler (FK) concentrator gives birth to a quite different CPV system where all the high-tech components sit on a common plane, that of the primary lens panels. The idea enables not only a thinner device (a half of the original) but also a low cost 1-step manufacturing process for the optics, automatic alignment of primary and secondary lenses, and cell/wiring protection. The concept is also compatible with two different techniques to increase the module efficiency: spectrum splitting between a 3J and a BPC Silicon cell for better usage of Direct Normal Irradiance DNI, and sky splitting to harvest the energy of the diffuse radiation and higher energy production throughout the year. Simple calculations forecast the module would convert 45% of the DNI into electricity.

14 SOLAR ENERGY↗

Controlling the charge of dust particles in an afterglow by modulating the plasma power

Abstract A dust particle immersed in a glow-discharge plasma has long been known to have a charge that is negative , while the plasma is powered. However, in the afterglow, following the stopping of the plasma power, a large positive charge can collect on the particle, as was shown recently for particles in a cathodic sheath. While that outcome of positive charging in the afterglow may be common, an experimental discovery reported here reveals that the opposite outcome is also possible: a particle can develop a negative charge in the afterglow, if the plasma had previously been operated with a modulated power. Before stopping the plasma power off altogether, in a run with power modulated at a low duty cycle of 4.5 % , the particle’s residual charge was negative, but it was positive in a control run without modulation. This result points to a way of controlling the charge of dust particles in a decaying plasma, which can be useful for mitigating defects in semiconductor manufacturing.

Physics↗

SU-E-T-286: Dose Verification of Spot-Scanning Proton Beam Using GafChromic EBT3 Film

Purpose: Dose verification of spot-scanning proton pencil beam is performed via planar dose measurements at several depths using an ionization-chamber array, requiring repeat irradiations of each field for each depth. Here we investigate film dosimetry which has two advantages: higher resolution and efficiency from one-shot irradiation for multiple depths. Methods: Film calibration was performed using an EBT3 film at 20-cm depth of Plastic Water (CIRS, Norfolk, VA) exposed by a 10-level step wedge on a Proteus Plus proton system (IBA, Belgium). The calibration doses ranged from 25–250 cGy(RBE) for proton energies of 170–200 MeV. A uniform 1000 cm{sup 3} dose cube and a clinical prostate combined with seminal-vesicle and pelvic-nodes plan were used for this study. All treatment plans were generated in the RayStation (RaySearch Lab, Sweden). The planar doses at different depths for both cases were measured with film using triple-channel dosimetry and the MatriXX PT (IBA Dosimetry, Germany). The Gamma passing rates, dose-difference maps, and profiles of 2D planar doses measured with EBT3 film and MatriXX, versus treatment planning system (TPS) calculations were analyzed and compared using the FilmQA Pro (Ashland Inc., Bridgewater, NJ). Results: The EBT3 film measurement results matched well with the TPS calculation data with an average passing rate >95% for 2%/2mm and are comparable with the MatriXX measurements (0.7%, 1.8%, 3.8% mean differences corresponding to 3%/3mm, 3%/2mm, 2%/2mm, respectively). Overall passing rates for EBT3 films appear higher than those with MatriXX detectors. Conclusion: The energy dependence of the film response could be minimized by calibration using proton beam with mixed energies. The greater efficiency of the dose verification using GafChromic EBT3 results in a potential cost trade-off between room capacity and film cost. EBT3 film may offer distinct advantages in highly intensity-modulated fields due to its higher resolution compared to 2D ionization-chamber array detectors. One of the authors has a research grant from Ashland Inc., the manufacturer of GafChromic film.

60 APPLIED LIFE SCIENCES↗

Lightweight PV Inverters: Dual Bi-Directional IGBTs Modules Enables Breakthrough PV Inverter Using Current Modulation Topology

Solar ADEPT Project: PV inverters convert DC power generated by modules into usable AC power. IPC’s initial 30kW 94lb. PV inverter reduces the weight of comparable 30kW PV inverters by 90%—reducing the cost of materials, manufacturing, shipping, and installation. With ARPA-E support, new bi-directional silicon power switches will be developed, commercialized, and utilized in IPC’s next-generation PV inverter. With these components, IPC will produce 100kW inverters that weight less than 100lb., reducing the weight of conventional 3,000lb. 100kW inverters by more than 95%. The new power switches will cut IPC’s $/W manufacturing cost in half, as well as further reduce indirect shipping and installation costs.

ARPA-E↗

Modulation of PEDOT:PSS pH for efficient inverted perovskite solar cells with reduced potential loss and enhanced stability

Inverted p-i-n perovskite solar cells (PVSCs) using PEDOT:PSS as the hole-transporting layer (HTL) is one of the most widely adopted device structures thus far due to its facile processability and good compatibility for high throughput manufacturing processes. However, most of the PEDOT:PSS-based CH 3 NH 3 PbI 3 PVSCs reported to date suffered an inferior open-circuit voltage (V OC ) (0.88-0.95 V) compared to that (1.05-1.12 V) obtained for common CH 3 NH 3 PbI 3 PVSCs, revealing a severe potential loss issue. Herein, we describe a simple method to alleviate this problem by tuning the pH value of PEDOT:PSS with a mild base, imidazole. Accompanied by the pH modulation, the blended imidazole concurrently tailors the surface texture and electronic properties of PEDOT:PSS to promote the quality and crystallization of the perovskite film deposited on top of it and enable better energy-level alignment at this corresponding interface. Consequently, the PVSC using this modified PEDOT:PSS HTL yields an enhanced power conversion efficiency (PCE) of 15.7% with an enlarged V OC of 1.06 V and improved long-term stability. Lastly, these outperform the pristine device showing a PCE of 12.7% with a much smaller V OC of 0.88 V and unsatisfactory environmental stability.

14 SOLAR ENERGY↗

High-density SSiC 3D-printed Lattices for Compact HTHP Aero-engine Recuperators

The proposed project utilizes advanced ceramic-based 3D-printing technology to develop light, low-cost, ultra-compact, high-temperature high-pressure (HTHP) heat exchangers (HX) for the harsh oxidizing environment of aircraft gas-turbine engines. Typical 3D printing technologies (powder bed or lithographic techniques) cannot produce large high-density, monolithic ceramic material with intricate internal features and channels required for high-temperature, high-pressure recuperators. Furthermore, typical 3D printing technologies are not yet economical for large high-density components. A high-density material is required for hermeticity, high-temperature strength, and oxidation, corrosion, and wear resistance. The team has invented an extrusion-based additive manufacturing technology (referred to as robocasting) and developed processing techniques to tailor composition and rheological mix properties for rapid 3D printing of high-density alumina and SiC parts. The goal of the proposed project is to use robocasting technology to demonstrate commercializable high-density 3D-printed ceramic HX modules with high durability and quality, thereby reducing the risk of thermo-mechanical failure under extreme environments. In addition, the proposed project improves the quality of the ceramic 3D-printing process over a large printed area and HTHP operating conditions. Ceramic 3D printing technology also provides a means to create advanced topologies that are unobtainable with conventional manufacturing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

United States Nuclear Manufacturing Infrastructure Assessment

This report provides a review and assessment of the existing U.S. infrastructure capabilities to manufacture on a commercial scale, the major components and unique materials required by the various U.S. designs for advanced nuclear reactors and small modular reactors (SMRs). The approach was to compare the needs of SMRs and advanced reactors against the capability of U.S. manufacturers to ascertain gaps that could inhibit U.S. industrial support for deployment of SMRs or advanced reactors. This report focused on the reactor plant designs being developed by NuScale Power (the NuScale Power Module), TerraPower (both the Traveling Wave Reactor and the Molten Chloride Fast Reactor to a limited extent), and X-energy (the Xe-100). To gather the information, MPR visited each of these companies and selected candidate suppliers to tour their facilities and conduct in-person interviews. Information was also obtained by telephone interviews, internet research, and literature review of technical reports. The overarching conclusion from this study is that the U.S. has existing capability or can readily develop capability to support and sustain most, but not all, aspects of commercial deployment of advanced reactors and SMRs. The greatest concerns for capability gaps in the U.S. infrastructure for supply of components for SMRs and advanced reactors are associated with reactor pressure vessels, steam generators, and fuel fabrication. Foreign vendors can supply reactor pressure vessels and steam generators. Issues with fuel fabrication are associated with uranium enrichment and development of fabrication methods for the innovative fuel concepts planned for advanced reactors. The technical capabilities of U.S. manufacturers appear satisfactory with the possible exceptions noted above. However, the capacity of the existing U.S. manufacturing infrastructure may be insufficient for a high rate of construction. Manufacturers contacted as part of this study indicated a willingness to expand capacity if sufficient orders are in place. The review of U.S. infrastructure included a detailed review of capabilities in many different processes including forging, tube drawing, machining, fabrication, and testing. In addition, MPR researched the advanced manufacturing processes for additive manufacturing (i.e., 3D printing) and powder metallurgy - hot isostatic pressing. Reactor plant designers and candidate suppliers are planning to rely on traditional processes for the initial plants. If advanced manufacturing processes are developed and accepted by the nuclear industry, these processes may be used in the future. In the immediate term, ongoing research (much of which is funded by DOE) is necessary to develop and refine advanced manufacturing methods. This report includes several recommendations for DOE that will advance deployment of SMRs and advanced reactors from a manufacturing perspective and other areas identified during the course of this project.

36 MATERIALS SCIENCE↗

SU-E-CAMPUS-T-05: Validation of High-Resolution 3D Patient QA for Proton Pencil Beam Scanning and IMPT by Polymer Gel Dosimetry

Purpose: Validation of high-resolution 3D patient QA for proton pencil beam scanning and IMPT by polymer gel dosimetry. Methods: Four BANG3Pro polymer gel dosimeters (manufactured by MGS Research Inc, Madison, CT) were used for patient QA at the Robert's Proton Therapy Center (RPTC, Philadelphia, PA). All dosimeters were sealed in identical thin-wall Pyrex glass spheres. Each dosimeter contained a set of markers for 3D registration purposes. The dosimeters were mounted in a consistent and reproducible manner using a custom build holder. Two proton pencil beam scanning plans were designed using Varian Eclipse™ treatment planning system: 1) A two-field intensity modulated proton therapy (IMPT) plan and 2) one single field uniform dose (SFUD) plan. The IMPT fields were evaluated as a composite plan and individual fields, the SFUD plan was delivered as a single field plan.Laser CT scanning was performed using the manufacturer's OCTOPUS-IQ axial transmission laser CT scanner using a 1 mm slice thickness. 3D registration, analysis, and OD/cm to absorbed dose calibrations were perfomed using DICOM RT-Dose and CT files, and software developed by the manufacturer. 3D delta index, a metric equivalent to the gamma tool, was used for dose comparison. Results: Very good agreement with single IMPT fields and with SFUD was obtained. Composite IMPT fields had a less satisfactory agreement. The single fields had 3D delta index passing rates (3% dose difference, 3 mm DTA) of 98.98% and 94.91%. The composite 3D delta index passing rate was 80.80%. The SFUD passing rate was 93.77%. Required shifts of the dose distributions were less than 4 mm. Conclusion: A formulation of the BANG3Pro polymer gel dosimeter, suitable for 3D QA of proton patient plans is established and validated. Likewise, the mailed QA analysis service provided by the manufacturer is a practical option when required resources are unavailable. We fully disclose that the subject of this research regards a production of MGS Research, Inc.

60 APPLIED LIFE SCIENCES↗

Heterogeneous Integration Technologies for High-temperature, High-density, Low-profile Power Modules of Wide Bandgap Devices in Electric Drive Applications (Final Technical Report)

The goal of this project is to develop packaging technologies for making high-temperature, high-density, and low-profile wide-bandgap (WBG) power electronics modules for electric drives. These modules are aimed at enabling the DOE’s University Consortium to reach its 2025 inverter targets of ≥ 100 kW/L and ≤ 2.7 $/kW. The specific objectives are to: design and fabricate SiC half-bridge power modules with double-sided cooling and parasitic inductances < 5 nH, heat flux density > 400 W/cm 2 , and working junction temperature of 200 o C; design, fabricate, and deliver a gate driver with double-sided cooled modules for the construction of a 100 kW/L inverter at Oak Ridge National Lab; and design and prototype intelligent gate drivers with integrated current sensor and a low-profile DC-DC power supply with air-core transformer for testing power modules at 200 o C junction temperature. We followed an iterative technical approach of design, simulation, fabrication, and testing of various versions of modules, current sensors, and power supply. The state-of-the-art silicon carbide devices rated at 1.2 kV and 149 A were packaged by sintered-silver bonding on an aluminum nitride direct-bond-copper substrate for high thermal conductivity, high working temperature, and high joint reliability. Porous silver posts were used to interconnect the device’s source pads to the other direct-bond-copper substrate for low mechanical stresses, ease of manufacturing, and double-sided cooling. A current sensor based on package parasitic inductance was developed to measure switching current. A dynamic feedback scheme was developed to compensate the effect of parasitic resistance and temperature variation. A constant-current class-E dc-dc converter with air-core transformer was developed. Air-core transformer was used due to the unavailability of magnetic core at high temperatures. Gate driver and power supply were integrated with the double-side cooled, high temperature SiC power modules for testing the modules at 200 o C junction temperature. Double-pulse and continuous testing of the integrated technologies validated the design and fabrication of the three component technologies. Throughout the project, we overcame the challenge for design verification caused by low prototyping yield, which then helped train the graduate students, the future workforce, to learn the engineering know-how for low-cost manufacturing of reliable products. Below is a summary of the major accomplishments of this project: development of a prototyping process for fabricating double-side cooled (1200 V, 149 A) SiC phase-leg modules capable of working to 200 o C Tj; simulation and experimental verification of the improvement of thermo-mechanical reliability of the double-side cooled SiC phase-leg module by using rigid encapsulant; design and experimental validation of a current sensor based on package parasitic inductance and a compensation solution for eliminating the effect of parasitic resistance; design and experimental validation of a low-profile power supply with six-output air-core transformer for gate driver; functional demonstration of a SiC phase-leg module integrated with its gate driver, current sensor, and an air-core power supply at 200 o C Tj in a double-pulse switching test setup and Buck converter continuous test setup; successful completion of six PhD and two MS students who are or will work at Apple Inc., Tesla Inc., Wolfspeed Inc., Microchip Inc., Monolithic Power Systems Inc., and LG Magna Inc.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

WE-D-17A-04: Magnetically Focused Proton Irradiation of Small Volume Targets

Purpose: To explore the advantages of magnetic focusing for small volume proton irradiations and the potential clinical benefits for radiosurgery targets. The primary goal is to create narrow elongated proton beams of elliptical cross section with superior dose delivery characteristics compared to current delivery modalities (eg, collimated beams). In addition, more general beam shapes are also under investigation. Methods: Two prototype magnets consisting of 24 segments of samarium-cobalt (Sm2Co17) permanent magnetic material adhered into hollow cylinders were manufactured for testing. A single focusing magnet was placed on a positioning track on our Gantry 1 treatment table and 15 mm diameter proton beams with energies and modulation relevant to clinical radiosurgery applications (127 to 186 MeV, and 0 to 30 mm modulation) were delivered to a terminal water tank. Beam dose distributions were measured using a PTW diode detector and Gafchromic EBT2 film. Longitudinal and transverse dose profiles were analyzed and compared to data from Monte Carlo simulations analogous to the experimental setup. Results: The narrow elongated focused beam spots showed high elliptical symmetry indicating high magnet quality. In addition, when compared to unfocused beams, peak-to-entrance depth dose ratios were 11 to 14% larger (depending on presence or extent of modulation), and minor axis penumbras were 11 to 20% smaller (again depending on modulation) for focused beams. These results suggest that the use of rare earth magnet assemblies is practical and could improve dose-sparing of normal tissue and organs at risk while delivering enhanced dose to small proton radiosurgery targets. Conclusion: Quadrapole rare earth magnetic assemblies are a promising and inexpensive method to counteract particle out scatter that tends to degrade the peak to entrance performance of small field proton beams. Knowledge gained from current experiments will inform the design of a prototype treatment nozzle that incorporates similar focusing magnets. This project was sponsored in part by funding from the Department of Defense (DOD# W81XWH-BAA-10-1)

60 APPLIED LIFE SCIENCES↗

Ultrasonic Characterization of Ethylene Vinyl Acetate (EVA) Crosslinking for Quality Assurance and Lamination Process Control (US-Xlink)

Module makers strive to cut lamination processing times to enhance production throughput and reduce costs. If overdone, this might lead to poor EVA quality due to incomplete EVA crosslinking and a large concentration of potentially harmful reactants. Those deficiencies are frequently missed during production quality testing as initially their impact on power output is small. Additionally, the crosslinking agent is frequently inhomogeneously dispersed across the EVA foils such that local destructive characterization procedures such as differential scanning calorimetry (DSC), Soxhlet extraction, swelling methods, or mechanical tests provide only a limited amount of information. However, these defects and inhomogeneities can become considerably more important during field operation, dramatically reducing long-term power yield, and increasing LCOE. Examples of typical long-term module degradation modes relating to poor lamination process conditions include cell breakage, corrosion of the metallization, delamination, and local quality deficiencies. To provide reliable material characterization in a manufacturing setting, we devised a non-destructive technology that uses ultrasound to evaluate the quality of interface adhesion and the degree of crosslinking. As a calibration reference, DSC measurements were employed. Although the potential of ultrasonic approaches for this purpose has already been noted, those previous methods were generally limited to local qualitative measurements. Furthermore, variations in EVA thickness and temperature had a substantial impact on them. The solution we propose solves these limitations by employing ultrasonic absorption rather than relying solely on sound velocity data.

14 SOLAR ENERGY↗

The impact of thermoelectric leg geometries on thermal resistance and power output

Thermoelectric devices enable direct, solid-state conversion of heat to electricity and vice versa. Rather than designing the shape of thermoelectric units or legs to maximize this energy conversion, the cuboid shape of these legs has instead remained unchanged in large part because of limitations in the standard manufacturing process. However, the advent of additive manufacturing (a technique in which freeform geometries are built up layer-by-layer) offers the potential to create unique thermoelectric leg geometries designed to optimize device performance. This work explores this new realm of novel leg geometry by simulating the thermal and electrical performance of various leg geometries such as prismatic, hollow, and layered structures. The simulations are performed for two materials, a standard bismuth telluride material found in current commercial modules and a higher manganese silicide material proposed for low cost energy conversion in high-temperature applications. The results include the temperature gradient and electrical potential developed across individual thermoelectric legs as well as thermoelectric modules with 16 legs. Even simple hollow and layered leg geometries result in larger temperature gradients and higher output powers than the traditional cuboid structure. As a result, the clear dependence of thermal resistance and power output on leg geometry provides compelling motivation to explore additive manufacturing of thermoelectric devices.

30 DIRECT ENERGY CONVERSION↗

Precursor Engineering of All-Inorganic Perovskite Absorber and Rapid Photonic Annealing for Large-Area Highly Stable Perovskite Solar Modules

Currently the all-inorganic perovskites were prepared by toxic dimethylformamide (DMF) as a main solvent, and small-area PSCs were prepared by a simple spin-coating method followed by lengthy thermal annealing. All these issues limited the commercialization of these PSCs. Therefore, it is necessary to develop an eco-friendly all-inorganic perovskite ink that can be coated over large areas at low temperatures followed by rapid annealing for the scale-up manufacturing with high compatibility to the industrial scale sheet-to-sheet or roll-to-roll processes.

14 SOLAR ENERGY↗

Morphological landscapes from high content imaging reveal cytokine priming strategies that enhance mesenchymal stromal cell immunosuppression

Abstract Successful clinical translation of mesenchymal stromal cell (MSC) products has not been achieved in the United States and may be in large part due to MSC functional heterogeneity. Efforts have been made to identify “priming” conditions that produce MSCs with consistent immunomodulatory function; however, challenges remain with predicting and understanding how priming impacts MSC behavior. The purpose of this study was to develop a high throughput, image‐based approach to assess MSC morphology in response to combinatorial priming treatments and establish morphological profiling as an effective approach to screen the effect of manufacturing changes (i.e., priming) on MSC immunomodulation. We characterized the morphological response of multiple MSC lines/passages to an array of Interferon‐gamma (IFN‐γ) and tumor necrosis factor‐⍺ (TNF‐⍺) priming conditions, as well as the effects of priming on MSC modulation of activated T cells and MSC secretome. Although considerable functional heterogeneity, in terms of T‐cell suppression, was observed between different MSC lines and at different passages, this heterogeneity was significantly reduced with combined IFN‐γ/TNF‐⍺ priming. The magnitude of this change correlated strongly with multiple morphological features and was also reflected by MSC secretion of immunomodulatory factors, for example, PGE2, ICAM‐1, and CXCL16. Overall, this study further demonstrates the ability of priming to enhance MSC function, as well as the ability of morphology to better understand MSC heterogeneity and predict changes in function due to manufacturing.

Andrews, Seth H.↗

SU-D-304-02: Magnetically Focused Proton Irradiation of Small Field Targets

Purpose: To investigate the use of magnetic focusing for small field proton irradiations. It is hypothesized that magnetic focusing will provide significant dose distribution benefits over standard collimated beams for fields less than 10 mm diameter. Methods: Magnets consisting of 24 segments of radiation hard samarium-cobalt adhered into hollow cylinders were designed and manufactured. Two focusing magnets were placed on a positioning track on our Gantry 1 treatment table. Proton beams with energies of 127 and 157 MeV, 15 and 30 mm modulation, and 8 mm initial diameters were delivered to a water tank using single-stage scattering. Depth dose distributions were measured using a PTW PR60020 diode detector and transverse profiles were measured with Gafchromic EBT3 film. Monte Carlo simulations were also performed - both for comparison with experimental data and to further explore the potential of magnetic focusing in silica. For example, beam spot areas (based on the 90% dose contour) were matched at Bragg depth between simulated 100 MeV collimated beams and simulated beams focused by two 400 T/m gradient magnets. Results: Preliminary experimental results show 23% higher peak to entrance dose ratios and flatter spread out Bragg peak plateaus for 8 mm focused beams compared with uncollimated beams. Monte Carlo simulations showed 21% larger peak to entrance ratios and a ∼9 fold more efficient dose to target delivery compared to spot-sized matched collimated beams. Our latest results will be presented. Conclusion: Our results suggest that rare earth focusing magnet assemblies could reduce skin dose and beam number while delivering dose to nominally spherical radiosurgery targets over a much shorter time compared to unfocused beams. Immediate clinical applications include those associated with proton radiosurgery and functional radiosurgery of the brain and spine, however expanded treatment sites can be also envisaged.

60 APPLIED LIFE SCIENCES↗

Metallic Cu Surface Enables Reversible Na Metal Anodes and Stabilizes Anode-Free Sodium Metal Batteries

Anode free Na metal batteries are promising for future energy storage because they not only provide the highest energy densities but also eliminate the need of handling hazardous Na metals during battery manufacturing. However, they suffer from much faster degradation due to strong sensitivities even to trace levels of side reactions. In view of the crucial roles of surface chemistry on modulating electrochemical plating, this work systematically investigated a series of Cu surfaces for Na plating and stripping in the 1.0 M NaPF 6 diglyme electrolyte. Our results suggest that Na plating and stripping on pure Cu surface without Cu oxide species exhibits much better reversibility and smaller overpotentials across a wide range of current densities, especially for the first plating/stripping cycle. The high performance includes consistently higher than 99.8% Faradaic efficiencies, much more stable interfacial resistance, and negligible formation of mossy Na after 500 cycles. This improved performance can be explained based on the stronger Na-Cu affinity compared with the Na-CuO affinity. Anode-free Na metal batteries equipped with high-capacity sodium vanadium phosphate cathodes and pure Cu current collector exhibited at least 70% capacity retention for 100 cycles.

Electrochemistry↗

Final Report MEPV

The MEPV Grand Challenge was focused on exploiting beneficial scaling effects in solar cells, modules, and systems to make solar power the lowest cost source of power available. The project explored new multijunction, microscale solar cell architectures, new micro-optical concentration methods, new hybrid solar collection concepts, and developed a series of prototypes to demonstrate these technologies. In addition, a detailed cost analysis was conducted to determine the costs of the proposed technologies and provide guidance for the system design efforts. Key results included demonstration of InGaP/GaAS cells transferred to active silicon cells to create a three junction cell with efficiency near 30%, the transfer of InGaAs cells to Si with demonstrated high performance of the InGaAs cell behind the Si substrate, the design, manufacture, and experimental demonstration of optics with almost 90% transmission efficiency and 100X and 200X concentration with a relatively large acceptance angle (>±1.5°), and the full assembly and demonstration of functional microconcentrator systems. The cost modeling efforts indicated that a module based on the best design resulting from the knowledge and technology develop would approach $1/Wpeak total installed system cost with no subsidies. If achieved in practice, this system would provide the lowest energy cost of any grid-tied energy source.

14 SOLAR ENERGY↗

Low cost back contact heterojunction solar cells on thin c-Si wafers. Integrating laser and thin film processing for improved manufacturability

An interdigitated back contact (IBC) Si wafer solar cell with deposited a-Si heterojunction (HJ) emitter and contacts is considered the ultimate single junction Si solar cell design. This was confirmed in 2014 by both Panasonic and Sharp Solar producing IBC-HJ cells breaking the previous record Si solar cell efficiency of 25%. But manufacturability at low cost is a concern for the complex IBC-HJ device structure. In this research program, our goals were to addressed the broad industry need for a high-efficiency c-Si cell that overcomes the dominant module cost barriers by 1) developing thin Si wafers synthesized by innovative, kerfless techniques; 2) integrating laser-based processing into most aspects of solar cell fabrication, ensuring high speed and low thermal budgets ; 3) developing an all back contact cell structure compatible with thin wafers using a simplified, low-temperature fabrication process; and 4) designing the contact patterning to enable simplified module assembly. There were a number of significant achievements from this 3 year program. Regarding the front surface, we developed and applied new method to characterize critical interface recombination parameters including interface defect density Dit and hole and electron capture cross-section for use as input for 2D simulation of the IBC cell to guide design and loss analysis. We optimized the antireflection and passivation properties of the front surface texture and a-Si/a-SiN/a-SiC stack depositions to obtain a very low (< 6 mA/cm2) front surface optical losses (reflection and absorption) while maintaining excellent surface passivation (SRV<5 cm/s). We worked with kerfless wafer manufacturers to apply defect-engineering techniques to improve bulk minority-carrier lifetime of thin kerfless wafers by both reducing initial impurities during growth and developing post-growth gettering techniques. This led insights about the kinetics of nickel, chromium, and dislocations in PV-grade silicon and to achieving millisecond lifetimes in kerfless silicon materials. Laser fired contacts to n-Si were developed for the first time using a Al/Sb/Ti metal stack giving contact resistances < 5 mOhm-cm2 when fired through several different dielectric layers. A new 2 step laser+chemical etch isolation technique was developed using a sacrificial top coating which avoids laser damage to Si passivation. Regarding the heterojunction emitter, analysis of front FHJ (1D) and IBC (2D) cells with range of p-layer conditions found that a 2-stage high/low doped p-layer was optimum: the low doped region has lower defects giving higher Voc and the high doped region gave a better contact to the metal. A significant effort was spent studying the patterning process and its contribution to degradation of passivation and reproducibility. Several promising new cleaning, contact and deposition patterning and processing approaches were implemented leading to fabrication of several runs with cells having 19-20% efficiency which were stable over several months. This program resulted in the training and support of 12 graduate students, publication of 21 journal papers and 14 conference papers.

14 SOLAR ENERGY↗