Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Structure and Superconductivity of Hydrogenated TiZr Alloys Under High Pressure

The effects of pressure on the structure and electrical transport properties, including electrical resistance and critical magnetic field values for superconductivity in pristine and hydrogenated TiZr alloys, were investigated. As pressure increased from ambient to 55 GPa, the structure of the pristine TiZr alloys transformed from hcp to bcc via an intermediate ω phase. The superconducting transition temperature (T c ) significantly increased from 1.76 K at ambient pressure to 15.5 K at 52.2 GPa, accompanied by an extrapolated upper critical field of 24.5 T at T = 0 K. In contrast, the hydrogenated samples exhibited substantially lower T c values compared to the pristine ones, with a T c of 4.6 K at 50.5 GPa and an extrapolated upper critical field of 1.8 T at T = 0 K. Upon decompression, the superconductivity in the hydrogenated sample persisted down to 25 GPa, disappearing when the pressure was reduced to 19 GPa. Synchrotron X-ray diffractions (XRD) analysis revealed the formation of three hydrides: I4/mmm-(Ti, Zr)H 2 , P6 3 /mmc-(Ti, Zr)H 3 , and I4̅3d-(Ti,Zr) 4 H 15 . Finally, by combining XRD and electrical resistance data, we tentatively propose that the P6 3 /mmc-(Ti, Zr)H 3 predominantly induces superconductivity. In contrast to superhydrides, where electron–phonon interactions increase the superconducting temperature at high pressure, hydrogen atoms in hcp-(Ti, Zr)H 3 reduce T c .

36 MATERIALS SCIENCE↗

Photoluminescence of Cr 3+ in β-Ga 2 O 3 and (Al 0.1 Ga 0.9 ) 2 O 3 under pressure

The effects of pressure on single crystals of Cr-doped gallium oxide (β-Ga 2 O 3 :Cr 3+ ) and aluminum gallium oxide [(Al 0.1 Ga 0.9 ) 2 O 3 ] were examined by measuring the wavelength shift in the spectral R lines. Photoluminescence (PL) spectra of these materials were collected from samples in diamond anvil cells at pressures up to 9 GPa. The β-Ga 2 O 3 :Cr 3+ R lines were found to shift linearly under hydrostatic pressure. The (Al 0.1 Ga 0.9 ) 2 O 3 R lines also show a linear shift but the R 1 line shifted less than for β-Ga 2 O 3 :Cr 3+ . The ratio of R 2 to R 1 peak areas vs pressure is dominated by nonradiative recombination. X-ray diffraction measurements of (Al 0.1 Ga 0.9 ) 2 O 3 indicate that its equation of state is similar to that of β-Ga 2 O 3 . β-Ga 2 O 3 :Cr 3+ was examined under non-hydrostatic conditions by using mineral oil as a pressure transmitting medium. Similar to the case in ruby, the R 1 line is much more sensitive to non-hydrostatic stress than R 2 . Spatially resolved PL of a sample at 8 GPa in mineral oil showed significant variations in the R 1 emission wavelength. Furthermore, these results suggest that the R 1 line can serve as a sensitive probe of alloy composition and non-hydrostatic stress, while the R 2 line is insensitive to these perturbations.

36 MATERIALS SCIENCE↗

Crystal structure of simple metals at high pressures

The effects of pressure on the crystal structure of simple (or sp-) elements are analysed in terms of changes in coordination number, packing density, and interatomic distances, and general rules are established. In the polyvalent elements from groups 14-17, the covalently bonded structures tend to transform to metallic phases with a gradual increase in coordination number and packing density, a behaviour normally expected under pressure. Group 1 and 2 metallic elements, however, show a reverse trend towards structures with low packing density due to intricate changes in their electronic structure. Complex crystal structures such as host-guest and incommensurately modulated structures found in these elements are given special attention in this review in an attempt to determine their role in the observed phase-transition sequences.

36 MATERIALS SCIENCE↗

THE EAST-WEST METHOD: AN EXPOSURE-INDEPENDENT METHOD TO SEARCH FOR LARGE-SCALE ANISOTROPIES OF COSMIC RAYS

The measurement of large-scale anisotropies in cosmic ray arrival directions at energies above 10{sup 13} eV is performed through the detection of extensive air showers (EAS) produced by cosmic ray interactions in the atmosphere. The observed anisotropies are small, so accurate measurements require small statistical uncertainties, i.e., large data sets. These can be obtained by employing ground detector arrays with large extensions (from 10{sup 4} to 10{sup 9} m{sup 2}) and long operation time (up to 20 years). The control of such arrays is challenging and spurious variations in the counting rate due to instrumental effects (e.g., data taking interruptions or changes in the acceptance) and atmospheric effects (e.g., air temperature and pressure effects on EAS development) are usually present. These modulations must be corrected very precisely before performing standard anisotropy analyses, i.e., harmonic analysis of the counting rate versus local sidereal time. In this paper we discuss an alternative method to measure large-scale anisotropies, the 'East-West method'. It was originally proposed in the 1940s to study asymmetries in the flux of solar cosmic rays and later applied by Nagashima et al. to EAS at higher energies. It is a differential method, as it is based on the analysis of the difference of the counting rates in the east and west directions. Besides explaining the principle, we present here its mathematical derivation, showing that the method is largely independent of experimental effects, that is, it does not require corrections for acceptance and/or for atmospheric effects. We explain the use of the method to derive the amplitude and phase of the anisotropy and demonstrate its power under different conditions of detector operation.

79 ASTRONOMY AND ASTROPHYSICS↗

Dynamics and control of orbiting flexible beams and platforms under the influence of solar radiation and thermal effects

Expressions for thermal deflections of uniform thin beams and plates exposed to solar heating are obtained as a function of the properties of the material and the solar incidence angle. The major effect of the solar radiation pressure interacting with the thermally deformed structure is found to give rise to disturbance moments on the structure. The thermal deformations of the structures are assumed to be within 0.1 percent of the characteristic length of the structure. With the assumed thermal deformations, the resulting uncontrolled transient responses of these geosynchronous orbiting structures to the solar radiation pressure induced disturbances are simulated. The resulting rigid modal oscillations are found to be an order of magnitude larger than for those cases previously considered in which only the solar radiation pressure effect on vibrating structures was treated. Modifications of control laws and/or the feedback gain values are considered in order to improve the transient response characteristics under the thermally induced disturbances.

Krishna, R.↗

CN radical reactions with hydrogen cyanide and cyanogen - Comparison of theory and experiment

The method of laser photolysis/laser-induced fluorescence is used to obtain absolute rate constants for CN radical reactions with HCN and C2N2. The rate constants were found to be temperature-dependent in the range 300-740 K and pressure independent in the range 100-600 Torr. Rice-Remsperger-Kassel-Marcus theory for both reactions employing the transition state parameters obtained by the BAC-MP4 method are made. These calculations yielded reasonable results for the CN + HCN reaction, predicting both the temperature dependence and pressure independence. No pressure effect was observed in the pressure range 100-1000 Torr at temperatures below 900 K, confirming the experimental results.

Yang, D. L.↗

Fluid-Dynamic Properties of Some Simple Sharp- and Blunt-Nosed Shapes at Mach Numbers from 16 to 24 in Helium Flow

The fluid-dynamic characteristics of flat plates, 5 deg and 10 deg wedges, and 5 deg and 10 deg cones have been investigated at Mach numbers from 16.3 to 23.9 in helium flow. The flat-plate results are for a leading-edge Reynolds number range of 584 to 19,500 and show that the induced pressure distribution is essentially linear with the hypersonic viscous interaction parameter bar X within the scope of this investigation. It is also shown that the rate at which the induced pressure varies with bar X is a linear function of the leading-edge Reynolds number. The wedge and cone results show that as the flow-deflection angle increases, the induced-pressure effects decrease and the measured pressures approach those predicted by inviscid shock theory.

Henderson, Arthur, Jr.↗

HyRAM (Hydrogen Risk Assessment Models) v. 1.0 (alpha)

HyRAM is a software toolkit that integrates data and methods relevant to assessing the safety of hydrogen fueling and storage infrastructure. The HyRAM toolkit integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, and characterizing the impact of hydrogen hazards (thermal effects from jet fires, thermal pressure effects from deflagrations) on people and structures. HyRAM incorporates generic probabilities for equipment failures for nine types of components, and probabilistic models for the impact of heat flux on humans and structures, with computationally and experimentally validated models of hydrogen release and flame physics. Version 1.0.0.280 can be used to quantify the likelihood and thermal consequences associated with gaseous hydrogen releases from user-defined hydrogen installations.

Groth, Katrina M.↗

Temperature effect on turbulent burning velocity of lean premixed hydrogen/air flames

Hydrogen has drawn great attention in recent years as a carbon-free fuel. The turbulent burning velocity (S T ) is an important parameter for the design and modeling of hydrogen-fueled engines given the high propagation speed of hydrogen flames. It has been well documented that S T of hydrogen flames can be dramatically increased by thermo-diffusive effects which are sensitive to thermodynamic conditions. Previous studies have mainly focused on the pressure effect on S T of lean hydrogen flames, while the temperature effect has been largely ignored. Here, in the present study, the turbulent burning velocity for a lean hydrogen/air mixture over a wide range of temperatures (300–641 K) and pressures (1–15 atm) is investigated through direct numerical simulations of statistically planar turbulent premixed flames. Results show that the variation of normalized turbulent burning velocity (S T /S L , where S L is the laminar flame speed) with temperature and pressure is mainly controlled by the variation of the stretching factor I 0 . While S T /S L is only marginally dependent on temperature at the atmospheric pressure, it exhibits a decreasing trend with temperature at an elevated pressure (10 atm). This is associated with different temperature dependencies of flame surface area enlargement at the two different pressures, despite the monotonically decreasing trends of I 0 with temperature at both pressures. In addition, under engine-relevant conditions where the temperature and pressure increase simultaneously, the promotion effect of pressure is found to be largely canceled out by the suppression effect of temperature, leading to only a slight increase in I 0 and S T /S L . The observed trends are further explained through detailed flame dynamic analysis. Furthermore, I 0 at different temperatures and pressures is found to correlate very well with the enhancement of fuel consumption rate in the critically strained laminar flames. The present study elucidates the strong impact of temperature on S T of lean premixed hydrogen/air flames at elevated pressures and provides new insights into the modeling of S T , especially for engine-relevant conditions.

Wang, Yiqing [Argonne National Laboratory (ANL), A↗

Overexpanded Performance of Conical Nozzles with Area Ratios of 6 and 9 With and Without Supersonic External Flow

An investigation of the thrust characteristics and internal pressure distributions of two convergent-divergent 15 deg. half-angle exhaust nozzles having area ratios of 6 and 9 was made in the NASA Lewis 10- by 10-foot supersonic wind tunnel. The tests were conducted at free-stream Mach numbers of 0, 2.0, 2.5, 3.0, and 3.5 over a range of nozzle pressure ratios from 3 to 105. Attempts were made to induce separation of the overexpanded nozzle flow using secondary airflow and a wedge. Nozzle flow expansion under all free-stream conditions followed one-dimensional theory until separation from the nozzle wall occurred. In quiescent air the nozzle flow expanded to a pressure approximately one-half the base pressure before separation. When the nozzles were tested with supersonic external flow at the same effective pressure ratios, the nozzle flow separated with negligible expansion below the base pressure. The effect of a supersonic stream on internal nozzle flow separation characteristics was well defined only at a free-stream Mach number of 2.0. Thrust data at supersonic free-stream conditions indicate that only a small percentage of the ideal nozzle thrust will be available at nozzle pressure ratios below design. However, the overexpanded primary nozzle thrust loss was decreased by injecting large quantities of secondary air near the nozzle exit. In most cases no net gain in thrust resulted from secondary-air injection when the nozzle thrust was compared with the ideal thrust of both the primary and secondary airflows.

Musial, Norman T.↗

Strain effects on the modulation of band gap and optical properties of direct band gap silicon

Highlights: • The ideal tensile strength and the cleave mechanism of D135-Si were studied in detail. • The strain effects on band gap were discussed. • The strain and pressure effects on the optical properties were studied. - Abstract: Based on the first-principles calculations, the strain effects on the optical properties of direct band gap silicon crystal D135-Si were systemically investigated. The stress-strain relations and phonon spectra show that the realistic peak tensile strengths in three principle symmetry crystallographic directions [100], [010] and [001] are 4.5, 9.7 and 12.1 GPa, respectively. By imposing the pressure and strain on structure, we studied the direct-indirect band gap transitions and obtained the ranges of the direct band gap, namely 0–4 GPa on pressure, −0.07–0, −0.04–0.08, and −0.01–0.03 on strain along a-, b- and c-direction, respectively. The imaginary part of the dielectric function was calculated to analyze the optical absorption property, which shows the strong adsorption coefficients in the visible range of the sunlight. The effect of pressure on the optical absorption property of structure is the smallest, and the strain effects are gradually enhanced along c-, b- and a-direction, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

WIPP PA Sensitivity Studies in Support of CRA-2014 Completeness Determination and Compliance Decision - 18209

The Waste Isolation Pilot Plant (WIPP) has been developed by the U.S. Department of Energy (DOE) for the geologic (deep underground) disposal of transuranic (TRU) waste. Containment of TRU waste at the WIPP is regulated by the U.S. Environmental Protection Agency (EPA). The DOE demonstrates compliance with the containment requirements by means of performance assessment (PA) calculations. WIPP PA calculations estimate the probability and consequence of potential radionuclide releases from the repository to the accessible environment for a regulatory period of 10,000 years after facility closure. Since TRU waste was first received at the WIPP in 1999, compliance recertification applications (CRAs) have been required by the EPA on five-year cycle. The latest CRA (CRA-2014) was submitted by the DOE to the EPA in 2014. As part of the application, a formal set of PA calculations (CRA-2014 PA) was performed and results were documented in detail. The CRA-2014 PA incorporated several parameter updates based on new data, as well as the implementation of a different model for panel closures, barriers planned for the opening of each waste panel. The results presented as part of the CRA-2014 showed via the required complementary cumulative distribution function (CCDF) release curves that the estimated releases were within compliance limits. As part of their process for reviewing the completeness of the CRA-2014 [1], the EPA formally requested that the DOE perform sensitivity studies based on EPA-requested changes to model parameters. The DOE performed and documented the results of three sensitivity studies described below: CRA14-SEN2 [2], CRA14-SEN3 [3], and CRA14-SEN4 [4]. In each case, the new analysis results were compared to CRA- 2014 PA (CRA14) results to determine the impact of the EPA-requested changes. CRA14-SEN2: the application of EPA-requested modified parameters in the operations and experimental (non-waste) areas of the repository to simulate an accelerated (instantaneous) creep closure, the inclusion of capillary pressure effects on relative permeability, and an increase in initial/residual brine saturation and residual gas saturation. The modifications to the repository model resulted in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the operations and experimental areas. However, the overall effects on total high-probability mean releases from the repository were entirely insignificant. It was concluded that the modeling assumptions associated with the operations and experimental areas of the repository have an insignificant effect on the prediction of total releases from the repository and/or adequacy of the current (CRA14) model to demonstrate compliance with the regulatory limits. CRA14-SEN3: the application of EPA-requested modified parameters in the panel closure areas and operations and experimental (non-waste) areas of the repository to simulate an accelerated (instantaneous) creep closure, the inclusion of capillary pressure effects on relative permeability, and an increase in initial/residual brine saturation and residual gas saturation. The modifications to the repository model predominantly result in increased pressures and decreased brine saturations in waste areas, increased pressures and brine saturations in the operations and experimental areas, and decreased brine and gas flows across all panel closures. The pressure increases in repository waste regions yielded slightly decreased brine saturations (on average) in those areas. However, the overall effects on total high-probability mean releases from the repository are entirely insignificant. It was concluded that the modeling assumptions made for this sensitivity study which were associated with the panel closures and north end areas of the repository have only a small effect on the prediction of total releases from the repository and/or adequacy of the current (CRA14) model to demonstrate compliance with the regulatory limits. CRA14-SEN4: the application of several changes to the current WIPP PA model (CRA14), including: parameter changes, use of an updated code, and a revised computational grid for the BRAGFLO code. The modifications to the repository model resulted in increased releases in all primary release mechanisms. The impacts of each EPA-requested change to CRA14 were analyzed with respect to each release mechanism in the CRA14-SEN4 study. Overall, total high-probability predicted mean releases from the repository were increased by about 15%. Total low-probability predicted mean releases were increased by about 107%. It was concluded that the EPA-requested changes to the CRA14 result in increases to the predicted total releases from the repository. However, releases calculated in the CRA14-SEN4 analysis remained below regulatory limits, demonstrating continued compliance of the WIPP. In January 2017, the EPA determined that CRA-2014 was complete and then began a technical evaluation of CRA-2014 to determine whether the WIPP continued to comply with the radiation protection standards for disposal. During their evaluation, the EPA utilized the sensitivity study results to inform their ultimate determination in July 2017 that the WIPP continues to comply with regulatory standards. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Melting of Magnesium Borohydride under High Hydrogen Pressure: Thermodynamic Stability and Effects of Nanoconfinement

The thermodynamic stability and melting point of magnesium borohydride were probed under hydrogen pressures up to 1000 bar (100 MPa) and temperatures up to 400 °C. At 400 °C, Mg(BH4)2 was found to be chemically stable between 700 and 1000 bar H2, whereas under 350 bar H2 or lower pressures, the bulk material partially decomposed into MgH2 and MgB12H12. The melting point of solvent-free Mg(BH4)2 was estimated to be 367-375 °C, which was above previously reported values by 40-90 °C. Our results indicated that a high hydrogen backpressure is needed to prevent the decomposition of Mg(BH4)2 before measuring the melting point and that molten Mg(BH4)2 can exist as a stable liquid phase between 367 and 400 °C under hydrogen overpressures of 700 bar or above. The occurrence of a pure molten Mg(BH4)2 phase enabled efficient melt-infiltration of Mg(BH4)2 into the pores of porous templated carbons (CMK-3 and CMK-8) and graphene aerogels. Both transmission electron microscopy and small-angle X-ray scattering confirmed efficient incorporation of the borohydride into the carbon pores. The Mg(BH4)2@carbon samples exhibited comparable hydrogen capacities to bulk Mg(BH4)2 upon desorption up to 390 °C based on the mass of the active component; the onset of hydrogen release was reduced by 15-25 °C compared to the bulk. Importantly, melt-infiltration under hydrogen pressure was shown to be an efficient way to introduce metal borohydrides into the pores of carbon-based materials, helping to prevent particle agglomeration and formation of stable closo-polyborate byproducts.

White, James L.↗

On use of CO{sub 2} chemiluminescence for combustion metrics in natural gas fired reciprocating engines.

Flame chemiluminescence is widely acknowledged to be an indicator of heat release rate in premixed turbulent flames that are representative of gas turbine combustion. Though heat release rate is an important metric for evaluating combustion strategies in reciprocating engine systems, its correlation with flame chemiluminescence is not well studied. To address this gap an experimental study was carried out in a single-cylinder natural gas fired reciprocating engine that could simulate turbocharged conditions with exhaust gas recirculation. Crank angle resolved spectra (266-795 nm) of flame luminosity were measured for various operational conditions by varying the ignition timing for MBT conditions and by holding the speed at 1800 rpm and Brake Mean effective Pressure (BMEP) at 12 bar. The effect of dilution on CO*{sub 2}chemiluminescence intensities was studied, by varying the global equivalence ratio (0.6-1.0) and by varying the exhaust gas recirculation rate. It was attempted to relate the measured chemiluminescence intensities to thermodynamic metrics of importance to engine research -- in-cylinder bulk gas temperature and heat release rate (HRR) calculated from measured cylinder pressure signals. The peak of the measured CO*{sub 2} chemiluminescence intensities coincided with peak pressures within {+-}2 CAD for all test conditions. For each combustion cycle, the peaks of heat release rate, spectral intensity and temperature occurred in that sequence, well separated temporally. The peak heat release rates preceded the peak chemiluminescent emissions by 3.8-9.5 CAD, whereas the peak temperatures trailed by 5.8-15.6 CAD. Such a temporal separation precludes correlations on a crank-angle resolved basis. However, the peak cycle heat release rates and to a lesser extent the peak cycle temperatures correlated well with the chemiluminescent emission from CO*{sub 2}. Such observations point towards the potential use of flame chemiluminescence to monitor peak bulk gas temperatures as well as peak heat release rates in natural gas fired reciprocating engines.

03 NATURAL GAS↗