Search NASA⌕ Search

SEARCH · Search NASA

Results for “Parametric Design Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Spacecraft Conceptual Design Compared to the Apollo Lunar Lander

Future human exploration of the Moon will require an optimized spacecraft design with each sub-system achieving the required minimum capability and maintaining high reliability. The objective of this study was to trade capability with reliability and minimize mass for the lunar lander spacecraft. The NASA parametric concept for a 3-person vehicle to the lunar surface with a 30% mass margin totaled was considerably heavier than the Apollo 15 Lunar Module "as flown" mass of 16.4 metric tons. The additional mass was attributed to mission requirements and system design choices that were made to meet the realities of modern spaceflight. The parametric tool used to size the current concept, Envision, accounts for primary and secondary mass requirements. For example, adding an astronaut increases the mass requirements for suits, water, food, oxygen, as well as, the increase in volume. The environmental control sub-systems becomes heavier with the increased requirements and more structure was needed to support the additional mass. There was also an increase in propellant usage. For comparison, an "Apollo-like" vehicle was created by removing these additional requirements. Utilizing the Envision parametric mass calculation tool and a quantitative reliability estimation tool designed by Valador Inc., it was determined that with today?s current technology a Lunar Module (LM) with Apollo capability could be built with less mass and similar reliability. The reliability of this new lander was compared to Apollo Lunar Module utilizing the same methodology, adjusting for mission timeline changes as well as component differences. Interestingly, the parametric concept's overall estimated risk for loss of mission (LOM) and loss of crew (LOC) did not significantly improve when compared to Apollo.

Young, C.↗
NASA NTRS2002

Computational Modeling of Vortex Generators for Turbomachinery

In this work computational models were developed and used to investigate applications of vortex generators (VGs) to turbomachinery. The work was aimed at increasing the efficiency of compressor components designed for the NASA Ultra Efficient Engine Technology (UEET) program. Initial calculations were used to investigate the physical behavior of VGs. A parametric study of the effects of VG height was done using 3-D calculations of isolated VGs. A body force model was developed to simulate the effects of VGs without requiring complicated grids. The model was calibrated using 2-D calculations of the VG vanes and was validated using the 3-D results. Then three applications of VGs to a compressor rotor and stator were investigated: 1) The results of the 3-D calculations were used to simulate the use of small casing VGs used to generate rotor preswirl or counterswirl. Computed performance maps were used to evaluate the effects of VGs. 2) The body force model was used to simulate large part-span splitters on the casing ahead of the stator. Computed loss buckets showed the effects of the VGs. 3) The body force model was also used to investigate the use of tiny VGs on the stator suction surface for controlling secondary flows. Near-surface particle traces and exit loss profiles were used to evaluate the effects of the VGs.

Chima, R. V.↗
NASA NTRS2023

Modeling and Simulation of a Parallel Hybrid Electric Regional Aircraft for the Electrified Powertrain Flight Demonstration (EPFD) Program

This paper presents a parametric modeling and integrated aircraft sizing and synthesis approach for a charge depleting parallel hybrid electric architecture. The developed models are integrated within the baseline thin-haul and regional aircraft. In addition to the physical architecture, different modes of operation enabled by propulsion system electrification are also modeled parametrically. The modes of operation presented in this paper are the peak power shaving, climb power electric boost, in-flight battery recharging, and electric taxi. The sizing of the powertrain and the aircraft are performed within the multidisciplinary analysis and optimization environment, E-PASS. The consideration of the physical system and its operation together provides a holistic approach where the propulsion system and the airframe are designed under an optimized power and energy management strategy. The parametric nature of the work enables the design space exploration for electrification and lays the groundwork for future technology projection and uncertainty quantification studies. The developed capability is generic and can be applied on other aircraft classes. The work is done as part of the Electrified Powertrain Flight Demonstration program.

electrified powertrain flight demonstration↗
NASA NTRS1980

Parametric study of helicopter aircraft systems costs and weights

Weight estimating relationships (WERs) and recurring production cost estimating relationships (CERs) were developed for helicopters at the system level. The WERs estimate system level weight based on performance or design characteristics which are available during concept formulation or the preliminary design phase. The CER (or CERs in some cases) for each system utilize weight (either actual or estimated using the appropriate WER) and production quantity as the key parameters.

Beltramo, M. N.↗
NASA NTRS1992

Impeller tandem blade study with grid embedding for local grid refinement

Flow non-uniformity at the discharge of high power density impellers can result in significant unsteady interactions between impeller blades and downstream diffuser vanes. These interactions result in degradation of both performance and pump reliability. The MSFC Pump Technology Team has recognized the importance of resolving this problem and has thus initiated the development and testing of a high head coefficient impeller. One of the primary goals of this program is to improve impeller performance and discharge flow uniformity. The objective of the present work is complimentary. Flow uniformity and performance gains were sought through the application of a tandem blade arrangement. The approach adopted was to numerically establish flow characteristics at the impeller discharge for the baseline MSFC impeller and then parametrically evaluate tandem blade configurations. A tandem design was sought that improves both impeller performance and discharge uniformity. The Navier-Stokes solver AEROVISC was used to conduct the study. Grid embedding is used to resolve local gradients while attempting to minimize model size. Initial results indicate that significant gains in flow uniformity can be achieved through the tandem blade concept and that blade clocking rather than slot location is the primary driver for flow uniformity.

Bache, George↗
NASA NTRS1999

Investigation of Vortex Flaps and Other Flow Control Devices on Generic High-Speed Civil Transport Planforms

A parametric cranked delta planform study has been conducted in the Langley 14- by 22-Foot Subsonic Tunnel with the following objectives: (1) to evaluate the vortex flap design methodology for cranked delta wings, (2) to determine the influence of leading-edge sweep and the outboard wing on vortex flap effectiveness, (3) to evaluate novel flow control concepts, and (4) to validate unstructured grid Euler computer code predictions with modeled vortex and trailing-edge flaps. Two families of cranked delta planforms were investigated. One family had constant aspect ratio, while the other had a constant nondimensional semispan location of the leading-edge break. The inboard leading-edge sweep of the planforms was varied between 68 deg., 71 deg., and 74 deg., while outboard leading-edge sweep was varied between 48 deg. and 61 deg. Vortex flaps for the different planforms were designed by an analytical vortex flap design method. The results indicate that the effectiveness of the vortex flaps was only slightly influenced by the variations in the parametric planforms. The unstructured grid Euler computer code was successfully used to model the configurations with vortex flaps. The vortex trap concept was successfully demonstrated.

Kjerstad, Kevin J.↗
NASA NTRS1989

Stability and dynamic analysis of a slender column with curved longitudinal stiffeners

The results of a stability design study are presented for a slender column with curved longitudinal stiffeners for large space structure applications. Linear stability analyses are performed using a link-plate representation of the stiffeners to determine stiffener local buckling stresses. Results from a set of parametric analyses are used to determine an approximate explicit expression for stiffener local buckling in terms of its geometric parameters. This expression along with other equations governing column stability and mass are assembled into a determinate system describing minimum mass stiffened column design. An iterative solution is determined to solve this system and a computer program incorporating this routine is presented. Example design problems are presented which verify the solution accuracy and illustrate the implementation of the solution routine. Also, observations are made which lead to a greatly simplified first iteration design equation relating the percent increase in column mass to the percent increase in column buckling load. From this, generalizations are drawn as to the mass savings offered by the stiffened column concept. Finally, the percent increase in fundamental column vibration frequency due to the addition of deployable stiffeners is studied.

Lake, Mark S.↗
NASA NTRS1977

AAFE large deployable antenna development program: Executive summary

The large deployable antenna development program sponsored by the Advanced Applications Flight Experiments of the Langley Research Center is summarized. Projected user requirements for large diameter deployable reflector antennas were reviewed. Trade-off studies for the selection of a design concept for 10-meter diameter reflectors were made. A hoop/column concept was selected as the baseline concept. Parametric data are presented for 15-meter, 30-meter, and 100-meter diameters. A 1.82-meter diameter engineering model which demonstrated the feasiblity of the concept is described.

Source record↗
NASA NTRS1982

Vibration analysis of three guyed tower designs for intermediate size wind turbines

Three guyed tower designs were analyzed for intermediate size wind turbines. The four lowest natural frequencies of vibration of the three towers concepts were estimated. A parametric study was performed on each tower to determine the effect of varying such tower properties as the inertia and stiffness of the tower and guys, the inertia values of the nacelle and rotor, and the rotational speed of the rotor. Only the two lowest frequencies were in a range where they could be excited by the rotor blade passing frequencies. There two frequencies could be tuned by varying the guy stiffness, the guy attachment point on the tower, the tower and mass stiffness, and the nacelle/rotor/power train masses.

Christie, R. J.↗
NASA NTRS1992

Mixing in the dome region of a staged gas turbine combustor

To lower NO(x) emissions from gas-turbine engines the effect of dome design and operational changes on the mixing quality in the fuel-rich region is studied. A statistical analysis is employed to establish the parametric sensitivity in this complex flow. A mixing-effectiveness index is defined and used to optimize the gas-species uniformity and the extent of reaction at the exit plane of the dome. Mixing effectiveness is tied to the fuel and air injection locations, the macroscale structure of the dome aerodynamics, and the level of turbulence. Increases in nozzle/air to fuel ratio, reference velocities, and the dome expansion angle increased the level of turbulence. The optimum configuration featured counter-swirling fuel and air streams and produced a strong torroidal recirculation zone, an effective spray angle of 45 degrees, and azimuthal velocities that decayed to zero inside of two duct diameters. The results underscore the system specific nature of mixing optimization.

Sowa, W. A.↗
NASA NTRS2008

Structural Efficiency of Stitched Rod-Stiffened Composite Panels with Stiffener Crippling

The structural efficiency of rod-stiffened stitched specimens is evaluated to determine their weight saving potential if the stiffeners were allowed to buckle at less than or equal to design ultimate load. Analytical and experimental results from rod-stiffened and blade-stiffened single-stiffener specimens are presented. In both cases, skin and flanges were stitched together through-the-thickness prior to curing. No mechanical fasteners were used for the assembly. Specimens were loaded to failure in axial compression. Failure modes are discussed. Finite element and experimental results agree for the response of the structures. For some specimen configurations, improved structural efficiency can be obtained by allowing stiffeners to buckle at design limit load rather than requiring that buckling not occur prior to design ultimate load. In addition, through-the-thickness stitching can change the failure mechanism by suppressing delamination between skin and flange. A parametric study is presented herein which describes the possible weight savings with this approach.

Jegley, Dawn C.↗
NASA NTRS1998

A Study of Fixed-Order Mixed Norm Designs for a Benchmark Problem in Structural Control

This study investigates the use of H2, p-synthesis, and mixed H2/mu methods to construct full-order controllers and optimized controllers of fixed dimensions. The benchmark problem definition is first extended to include uncertainty within the controller bandwidth in the form of parametric uncertainty representative of uncertainty in the natural frequencies of the design model. The sensitivity of H2 design to unmodelled dynamics and parametric uncertainty is evaluated for a range of controller levels of authority. Next, mu-synthesis methods are applied to design full-order compensators that are robust to both unmodelled dynamics and to parametric uncertainty. Finally, a set of mixed H2/mu compensators are designed which are optimized for a fixed compensator dimension. These mixed norm designs recover the H, design performance levels while providing the same levels of robust stability as the u designs. It is shown that designing with the mixed norm approach permits higher levels of controller authority for which the H, designs are destabilizing. The benchmark problem is that of an active tendon system. The controller designs are all based on the use of acceleration feedback.

Whorton, Mark S.↗
NASA NTRS1979

Unconventional nozzle tradeoff study

Plug cluster engine design, performance, weight, envelope, operational characteristics, development cost, and payload capability, were evaluated and comparisons were made with other space tug engine candidates using oxygen/hydrogen propellants. Parametric performance data were generated for existing developed or high technology thrust chambers clustered around a plug nozzle of very large diameter. The uncertainties in the performance prediction of plug cluster engines with large gaps between the modules (thrust chambers) were evaluated. The major uncertainty involves, the aerodynamics of the flow from discrete nozzles, and the lack of this flow to achieve the pressure ratio corresponding to the defined area ratio for a plug cluster. This uncertainty was reduced through a cluster design that consists of a plug contour that is formed from the cluster of high area ratio bell nozzles that have been scarfed. Light-weight, high area ratio, bell nozzles were achieved through the use of AGCarb (carbon-carbon cloth) nozzle extensions.

Obrien, C. J.↗
NASA NTRS1979

Solar power satellite system definition study, volume 4, phase 2

Results of an overall evaluation of the solar power satellite concept are reported. Specific topics covered include: solid state sandwich configuration; parametric development of reliability design; power distribution system for solid state solar power satellites; multibeam transmission; GEO base system configuration; suppression of the heavy lift launch vehicle trajectory; conceptual design of an offshore space center facility; solar power satellite development and operations scenario; and microwave power transmission technology, advancement, development, and facility requirements.

Source record↗
NASA NTRS1980

Solid state SPS microwave generation and transmission study. Volume 2, phase 2: Appendices

The solid state sandwich concept for SPS was further defined. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. Basic solid state microwave devices were defined and modeled. An initial conceptual subsystems and system design was performed as well as sidelobe control and system selection. The selected system concept and parametric solid state microwave power transmission system data were assessed relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers and Gaussian tapers. A hybrid concept using tubes and solid state was evaluated. Thermal analyses are included with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗
DOE OSTI2022

Study of effect of PWR cold leg temperature gradient on reactor core condition

Effects of temperature and flow gradients in Westinghouse designed three-loop Pressurized Water Reactor (PWR) cold legs, the piping between the main coolant pump and the reactor vessel, were evaluated using Computational Fluid Dynamics (CFD) code STAR CCM+ and coupled neutronic and thermal-hydraulic (T/H) code system VERA. In the parametric study, several symmetric and asymmetric temperature gradients that were significantly larger than those observed from plant measurements were applied to the cold leg inlets for comparison with the base case without any temperature gradient. A CFD model using the STAR-CCM+ code was developed for a portion of the RCS region between the Reactor Coolant Pump (RCP) and the core inlet based on previously validated modeling approach. The CFD simulation results were processed for the temperature and flow rate distributions at the core inlet as input to the VERA calculations. The VERA code system consists of COBRA-TF (CTF) for thermal-hydraulics, MPACT for reactor physics and neutron transport, and ORIGEN for isotopic depletion. The VERA model was for depletion calculations of a high-burnup loading pattern with the reactor core in pin-by-pin and subchannel resolution. The results of the study indicate that the postulated temperature gradients within the PWR cold legs do not result in any significant changes in the core inlet temperature distributions and the core power distributions during the reactor operation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRSDate not supplied

Analysis and Optimization of Baseline Single Aisle Aircraft for Future Electrified Powertrain Flight Demonstrator Comparisons

The purpose of this study is to provide baseline single-aisle vehicles for future comparisons with NASA’s Electrified Powertrain Flight Demonstration (EPFD) turbofan-powered Vision Systems. State-of-the-art single-aisle transports with varying design capacities of 100 to 150 passengers are modeled using NASA Ames Research Center’s General Aviation Synthesis Program (GASP) as well as GASPy. GASPy is a modernized Python-based version of GASP built on the OpenMDAO framework to allow for future, efficient gradient-based optimization and coupled airframe-propulsion design. In order to meet projected NASA Aeronautics goals for 2035, advanced aircraft technologies must be incorporated into these vehicle systems. Methodology to parametrically infuse baseline aircraft models with advanced technologies simulating improvements in aerodynamics, structures, and propulsion systems is detailed, along with the results of technology sensitivity studies. Comparison of the baseline and advanced configurations will allow for future analysis of the benefits of future hybrid and fully electric aircraft concepts in the EPFD project, where fuel consumption and emissions will be modeled and assessed. This study has been conducted under the EPFD project to establish benchmark turbofan models and demonstrate System Analysis capabilities in multi-disciplinary aircraft design, analysis, and optimization for advanced turbofan concepts.

Carl J. Recine↗
NASA NTRS1985

The effect of engine design characteristics on orbital transfer vehicle performance

The objective in maximizing performance for a space-based Orbital Transfer Vehicle (OTV) is to minimize the propellant required to successfully complete a given reference mission and thereby reduce launch and storage costs. Engine sizing studies were conducted which examined the effect of engine design characteristics on the total propellant required to accomplish the manned and unmanned OTV missions anticipated for the 1995 to 2010 time period. Two propellant combinations, O2/H2 and N2O4/MMH, were selected as baselines. Exotic combinations such as F2/H2 and O2/CH4 were also studied to identify potential benefits and growth capabilities. Parametric results showing the effects of engine thrust, number of engines, nozzle area ratio and payload requirements are presented for various reference missions. The results indicate that the optimum engine size and thrust are not significantly affected by detailed engine design characteristics.

Schmidt, G. R.↗