Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reductive Effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Beirut Explosion Yield and Mushroom Cloud Height - Effects of the Source Environment

I use crater dimensions to estimate the yield of the August 4th, 2020 Beirut explosion to be equivalent to approximately 1.4 kilotons of TNT with a lower bound of about 0.7 kilotons. Based on the amount of ammonium nitrate reported to have been stored at the Beirut harbor, I assume an upper bound for the yield of 2.75 kilotons. However, it is highly likely that the yield was less than 2.75 kilotons, since reported values for TNT equivalence of ammonium nitrate are typically much less than one hundred percent. The crater-size based yield estimates are based on crater radius estimates from satellite imagery and empirical curves and data for scaled crater radius from past chemical and nuclear explosions. I present evidence that suggests that the relatively large crater radius is due to a high degree of coupling of shock wave energy to the surrounding medium and a reduction of the effective stress because of a high level of saturation of the geologic media beneath the explosion. I provide yield estimates based on seismic body-wave magnitude and crater depth as corroborating evidence. I compare preliminary estimates for the maximum debris cloud height, based on cell phone videos/images, with predicted maximum heights for this yield range from empirical formulas and numerical cloud-rise models. Based on a preliminary analysis of cell phone footage, the observed maximum cloud height appears to be approximately 1600 m. This is much lower than that predicted using standard empirical formulas and buoyant cloud rise models. I present results from a modified buoyant cloud rise model that more accurately predicts the maximum cloud height by allowing for the inclusion of a fixed amount of air and/or water into the fireball at the start of cloud rise. The amount of mass that needs to be added at the start, to reproduce the observed maximum cloud height, is relatively small compared to the total mass entrained during cloud rise. A much greater amount of dry air or debris is required, relative to water, for an equivalent reduction in maximum cloud height. The ammonium nitrate is one possible source for water in the fireball since it was being stored in a very humid environment and ammonium nitrate is known to be hygroscopic. The ground beneath the explosion, especially if it were saturated, and the nearby harbor could also have been sources for water or debris in the fireball.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS2012

Simulation Modeling Requirements for Loss-of-Control Accident Prevention of Turboprop Transport Aircraft

In-flight loss of control remains the leading contributor to aviation accident fatalities, with stall upsets being the leading causal factor. The February 12, 2009. Colgan Air, Inc., Continental Express flight 3407 accident outside Buffalo, New York, brought this issue to the forefront of public consciousness and resulted in recommendations from the National Transportation Safety Board to conduct training that incorporates stalls that are fully developed and develop simulator standards to support such training. In 2010, Congress responded to this accident with Public Law 11-216 (Section 208), which mandates full stall training for Part 121 flight operations. Efforts are currently in progress to develop recommendations on implementation of stall training for airline pilots. The International Committee on Aviation Training in Extended Envelopes (ICATEE) is currently defining simulator fidelity standards that will be necessary for effective stall training. These recommendations will apply to all civil transport aircraft including straight-wing turboprop aircraft. Government-funded research over the previous decade provides a strong foundation for stall/post-stall simulation for swept-wing, conventional tail jets to respond to this mandate, but turboprops present additional and unique modeling challenges. First among these challenges is the effect of power, which can provide enhanced flow attachment behind the propellers. Furthermore, turboprops tend to operate for longer periods in an environment more susceptible to ice. As a result, there have been a significant number of turboprop accidents as a result of the early (lower angle of attack) stalls in icing. The vulnerability of turboprop configurations to icing has led to studies on ice accumulation and the resulting effects on flight behavior. Piloted simulations of these effects have highlighted the important training needs for recognition and mitigation of icing effects, including the reduction of stall margins. This paper addresses simulation modeling requirements that are unique to turboprop transport aircraft and highlights the growing need for aerodynamic models suitable for stall training for these configurations. A review of prominent accidents that involved aerodynamic stall is used to illustrate various modeling features unique to turboprop configurations and the impact of stall behavior on susceptibility to loss of control that has led to new training requirements. This is followed by an overview of stability and control behavior of straight-wing turboprops, the related aerodynamic characteristics, and a summary of recent experimental studies on icing effects. In addition, differences in flight dynamics behavior between swept-wing jets and straight-wing turboprop configurations are discussed to compare and contrast modeling requirements. Specific recommendations for aerodynamic models along with further research needs and data measurements are also provided. 1

Crider, Dennis↗
DOE OSTI2022

Diesel-Range Fuel Property Effects on Medium-Duty Advanced Compression Ignition for Low-Load NO X Reduction

A diesel premixed-charge compression ignition (PCCI) technique was used at low loads at which exhaust temperature makes urea-selective catalytic reduction (SCR) use for nitrogen oxides (NOx) reduction challenging. A fuels matrix to examine the effects of increasing fuel volatility, bio-blendstocks, and cetane number on PCCI was formulated using a near-constant 15% aromatic content. The results showed that PCCI could provide greater than 67% NOx emissions reductions at 1,200 RPM, 3.1 bar indicated mean effective pressure (IMEP), and 2.0 bar IMEP. The filter smoke number (FSN) could also be reduced relative to a conventional diesel combustion (CDC) baseline. The reductions in FSN were more moderate in the order of 40-50%, depending upon the fuel used, IMEP, and combustion phasing (CA50) timing. Hydrocarbon (HC) emissions could be held to a marginally lower level than CDC emissions at some CA50 conditions by using higher-volatility and higher cetane number fuels and could potentially be traded for further NOx reductions. This outcome is important as it points to the possibility of achieving significant NOx reduction while doing no harm in terms of HC emissions. Carbon monoxide (CO) emissions increased in PCCI, but increasing the fuel volatility and cetane number could be helpful in keeping these emissions at a manageable level.

02 PETROLEUM↗
DOE OSTI2021

Assessing the impact of demand response on peak demand in a developing country: The case of Ghana

Peak demand on electricity grids is a growing problem that increases costs and risks to supply security. Residential sector loads often contribute significantly to seasonal and daily peak demand. Demand response refers to consumer actions that change the utility load profile in a way that reduces costs or improves grid security by applying price signals and automated load shedding technologies. The methodologies that are used to achieve demand response can hardly be applicable in developing countries. Peak pricing of electricity, for instance, can hardly be implemented in many developing countries as high prices would disproportionately affect the many low-income households who do not have the capacity to take action to avoid paying high peak prices. This study aims to develop demand response methodology that can be applied in developing countries to achieve residential peak demand reduction. We use a consumer preference survey to develop a methodology suitable for developing countries. The method of diversified demand is used with energy audit and monitored data to estimate the potential peak load reduction and its cost-effectiveness for Ghana. Results show that peak reduction of 15-210 MW is expected by 2040 with a positive return on investment of 2-22% for all designed scenarios.

Diawuo, FA↗
NASA NTRS1979

Microbial Sulfate Reduction Measured by an Automated Electrical Impedance Technique

Electrical impedance measurements are used to investigate the rates of sulfate reduction by pure cultures of and sediments containing sulfur-reducing bacteria. Changes in the electrical impedance ratios of pure cultures of Desulfovibrio aestuarii and samples of reduced sediments from San Francisco Bay were measured by a Bactometer 32, and sulfate reduction was followed by measuring the incorporation of (S-35) sulfate into metal sulfides. The growth of the bacteria in pure culture is found to result in an increase of 0.2200 in the impedance ratio within 24 h, accompanied by increases in protein, ATP, sulfide and absorptance at 660 nm, all of which are inhibited by the addition of molybdate. Similar responses were observed in the sediments, although impedance ratio responses were not completely inhibited upon the addition of molybdate, due to the presence of nonsulfate-respiring microorganisms. Experiments conducted with sterile media and autoclaved sediments indicate that the presence of H2S together with iron is responsible for the impedance effect, and sulfate reduction rates ranging between 0.85 and 1.78 mmol/l per day are estimated for the sediments by the impedance technique.

Oremland, R. S.↗
DOE OSTI2019

Effect of Zero Valent Iron Pre-treatments on Reductive Removal of Aqueous Tc-99 - 19379

Zero-valent iron (ZVI) is being investigated as a potential material for technetium-99 (Tc-99) reductive separation from the secondary liquid waste, i.e. off-gas condensate that will be generated during vitrification of the law activity waste (LAW) at the Hanford site. In this work, we performed a comparative analysis of Tc(VII) removal kinetics via its reduction with the commercially available ZVI materials varying in particle size (granules, filings, and 200 mesh). In addition to particle size differences, reduction removal potential was also evaluated as a function of as-received ZVI material versus a surface treatment. ZVI treatment experiments with 0.4 M HCl and 1 M NaCl were conducted to study the effect of iron oxide/oxyhydroxide formation on its reductive efficiency for aqueous Tc(VII) removal. Scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) analyses were conducted for all ZVI materials in the presence and absence of treatments to evaluate morphological differences (SEM) and chemical composition (EDS) of the materials. Reductive removal of Tc(VII) was also analyzed using a first-order kinetic model. The results of the study indicated that rate constants did not change with increased oxide/oxyhydroxide content in large ZVI materials (granules and filings), but decreased significantly for the relatively small ZVI (200 mesh), treated with 0.4 M HCl and 1 M NaCl. This study demonstrates that the commercial ZVI material 200 mesh, used as received, is a promising candidate for the removal of Tc from liquid secondary waste generated during Hanford LAW vitrification. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2023

Effects of Layer Spacing for a Multilayered Facesheet Acoustic Liner

A single degree-of-freedom acoustic liner, a perforate facesheet over honeycomb core, is modified to have a facesheet comprised of three layers. The top and bottom perforate layers have the same dimensions with aligned perforations while the middle layer perforate can be longitudinally shifted up to 0.075 inches to change the effective porosity of the facesheet. These configurations range in porosity from 100% open down to 10% open in addition to two closed configurations (0% porosity). Gaps are introduced between the facesheet layers ranging from no gap to 0.016 inches. These configurations are tested in the NASA Langley Grazing Flow Impedance Tube to determine their acoustic impedance spectra. Introduction of a gap affects the acoustic impedance of the liner where the resonant frequency of the liners decreases with increased gap thickness for liners with an open area ratio above 25% but increases with gap thickness for liners with an open area ratio below 25%. Additionally, it is observed that increasing the gap height results in a reduction of the effect of porosity on acoustic impedance. The results show that the presence of such gaps can have a significant effect on liner impedance especially as porosity decreases.

acoustic liners↗
NASA NTRS1992

Flow visualizations of perpendicular blade vortex interactions

Helium bubble flow visualizations have been performed to study perpendicular interaction of a turbulent trailing vortex and a rectangular wing in the Virginia Tech Stability Tunnel. Many combinations of vortex strength, vortex-blade separation (Z(sub s)) and blade angle of attack were studied. Photographs of representative cases are presented. A range of phenomena were observed. For Z(sub s) greater than a few percent chord the vortex is deflected as it passes the blade under the influence of the local streamline curvature and its image in the blade. Initially the interaction appears to have no influence on the core. Downstream, however, the vortex core begins to diffuse and grow, presumably as a consequence of its interaction with the blade wake. The magnitude of these effects increases with reduction in Z(sub s). For Z(sub s) near zero the form of the interaction changes and becomes dependent on the vortex strength. For lower strengths the vortex appears to split into two filaments on the leading edge of the blade, one passing on the pressure and one passing on the suction side. At higher strengths the vortex bursts in the vicinity of the leading edge. In either case the core of its remnants then rapidly diffuse with distance downstream. Increase in Reynolds number did not qualitatively affect the flow apart from decreasing the amplitude of the small low-frequency wandering motions of the vortex. Changes in wing tip geometry and boundary layer trip had very little effect.

Rife, Michael C.↗
NASA NTRS1993

Experiments on near-wall structure of three-dimensional boundary layers

Investigations of three-dimensional turbulent boundary layers have shown basic differences between two- and three-dimensional flows. These differences can significantly impact the modeling of three-dimensional flows since many flow models are based on results from two-dimensional boundary layers. In many cases the shear stress vector direction has been shown to lag relative to the direction of the mean velocity gradient as the cross flow grows downstream. Coincidence of these vectors is necessary for a scalar eddy viscosity modeling assumption. A second effect is a reduction in magnitude of the shear stress and/or the shear stress to turbulence energy ratio, a(sub 1). This reduction has been observed in several experiments. Recent numerical simulations also indicate wall-layer structural differences between two- and three-dimensional boundary layers. The differences in structure between two- and three-dimensional boundary layers was also addressed in the experiment of Littell & Eaton. The experiment used two-point correlations to investigate the vortical structures in a three dimensional boundary layer on a spinning disk. It was found that each sign of longitudinal vortex is equally likely to exist, but one sign of vorticity is associated with a structure which is better at producing ejections. The goal of the current investigation is to study the structure of the inner layers. Among other questions, the differences between the effects deduced from the three-dimensional flow simulations and the effects seen in experiments can be examined. The research concentrates on the structure of the wall-layer through flow visualization and direct turbulence measurements down to y(+) = 5.

Flack, Karen A.↗
NASA NTRS2011

Validation and Simulation of Ares I Scale Model Acoustic Test - 3 - Modeling and Evaluating the Effect of Rainbird Water Deluge Inclusion

The Ares I Scale Model Acoustics Test (ASMAT) is a series of live-fire tests of scaled rocket motors meant to simulate the conditions of the Ares I launch configuration. These tests have provided a well documented set of high fidelity measurements useful for validation including data taken over a range of test conditions and containing phenomena like Ignition Over-Pressure and water suppression of acoustics. Building on dry simulations of the ASMAT tests with the vehicle at 5 ft. elevation (100 ft. real vehicle elevation), wet simulations of the ASMAT test setup have been performed using the Loci/CHEM computational fluid dynamics software to explore the effect of rainbird water suppression inclusion on the launch platform deck. Two-phase water simulation has been performed using an energy and mass coupled lagrangian particle system module where liquid phase emissions are segregated into clouds of virtual particles and gas phase mass transfer is accomplished through simple Weber number controlled breakup and boiling models. Comparisons have been performed to the dry 5 ft. elevation cases, using configurations with and without launch mounts. These cases have been used to explore the interaction between rainbird spray patterns and launch mount geometry and evaluate the acoustic sound pressure level knockdown achieved through above-deck rainbird deluge inclusion. This comparison has been anchored with validation from live-fire test data which showed a reduction in rainbird effectiveness with the presence of a launch mount.

Strutzenberg, Louise L.↗
DOE OSTI2019

Compounding climate change impacts during high stress periods for a high wind and solar power system in Texas

Power system planning aims at ensuring that sufficient supply- and demand-side assets exist to meet electricity demand at all times. For a Texas electric power system with high wind and solar penetrations, we quantify how climate change will affect supply and demand during three types of high stress periods for the power grid: high demand hours, high net demand hours, and high system ramp hours. We specifically quantify effects on demand, reductions in available thermal capacity (i.e. thermal deratings), wind and solar generation, and net demand. We estimate each using meteorological variables from five climate change projections (2041-2050) assuming Representative Concentration Pathway 8.5 and from a reference period (1996-2005). All five projections indicate that climate change will increase demand by up to 2 GWh during high demand hours (4% of demand in the reference period) and increase net demand by up to 3 GWh during high net demand periods (6% of net demand in the reference period). All five projections also indicate thermal deratings will increase during high demand and net demand periods by up to 2 GWh and high net demand ramps will increase by up to 2 GW. Overall, our results indicate compounding effects of climate change in Texas will necessitate greater investment in peak and flexible capacity.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Simulated Hydrological Dynamics and Coupled Iron Redox Cycling Impact Methane Production in an Arctic Soil

The fate of organic carbon (C) in permafrost soils is important to the climate system due to the large global stocks of permafrost C. Thawing permafrost can be subject to dynamic hydrology, making redox processes an important factor controlling soil organic matter (SOM) decomposition rates and greenhouse gas production. In iron (Fe)-rich permafrost soils, Fe(III) can serve as a terminal electron acceptor, promoting anaerobic respiration of SOM and increasing pH. Current large-scale models of Arctic C cycling do not include Fe cycling or pH interactions. Here, a geochemical reaction model was developed by coupling Fe redox reactions and C cycling to simulate SOM decomposition, Fe(III) reduction, pH dynamics, and greenhouse gas production in permafrost soils subject to dynamic hydrology. In this study we parameterized the model using measured CO 2 and CH 4 fluxes as well as changes in pH, Fe(II), and dissolved organic C concentrations from oxic and anoxic incubations of permafrost soils from polygonal permafrost sites in northern Alaska, United States. In simulations of repeated oxic-anoxic cycles, Fe(III) reduction during anoxic periods enhanced CO 2 production, while the net effect of Fe(III) reduction on cumulative CH 4 fluxes depended on substrate C availability. With lower substrate availability, Fe(III) reduction decreased total CH 4 production by further limiting available substrate. With higher substrate availability, Fe(III) reduction enhanced CH 4 production by increasing pH. Our results suggest that interactions among Fe-redox reactions, pH and methanogenesis are important factors in predicting CH 4 and CO 2 production as well as SOM decomposition rates in Fe-rich, frequently waterlogged Arctic soils.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1971

Planetary quarantine

Methods for presterilization cleaning or decontamination of spacecraft hardware to reduce microbial load, without harming materials or spacecraft components, are investigated. Three methods were considered: (1) chemicals in liquid form, relying on physical removal as well as bacterial or bacteriostatic action; (2) chemicals used in the gaseous phase, relying on bacterial activity; and (3) mechanical cleaning relying on physical removal of organisms. These methods were evaluated in terms of their effectiveness in microbial burden reduction and compatibility with spacecraft hardware. Results show chemical methods were effective against spore microorganisms but were harmful to spacecraft materials. Mechanical methods were also effective with the degree depending upon the type of instrument employed. Mechanical methods caused problems in handling the equipment, due to vacuum pressure damaging the very thin layered materials used for shielding, and the bristles used in the process caused streaks or abrasions on some spacecraft components.

Source record↗
NASA NTRS1990

Differential effects of scopolamine and amphetamine on microcomputer-based performance tests

The effects of four weekly treatments with scopolamine (1.0 mg) and d-amphetamine (10 mg), separately or in combination, on human performance were investigated in 16 subjects undergoing nine performance tests from a menu of microcomputer-based tests administered after the treatment. It was d-amphetamine treatment that enhanced the results of motor and perceptual speed tests, while scopolamine had no effect on these tests. Two of the five cognitive tests showed reductions with scopolamine. The effects of scopolamine in this and other studies are considered in terms of a model which implies that the magnitude of the performance deficit depends on the performance type and the dosage level of the drug.

Kennedy, Robert S.↗
NASA NTRSDate not supplied

Zircon (U-Th)/He Impact Crater Thermochronometry and the Effects of Shock Microstructures on Helium Diffusion Kinetics

Accurate and precise age determination of impact cratering events remains challenging and often contentious; less than half of all known craters are regarded as accurately and precisely dated. Zircon (U-Th)/He (ZHe) dating of impactites can be employed to date medium to large impact structures as ZHe ages can be fully reset in minutes at T >1000°C, a plausible scenario in the central melt pool. In contrast, complete resetting of ZHe at 200-300°C, encountered near the crater margins or due to post-impact hydrothermal overprinting, may take >103-6 years. To test the reliability of ZHe impact dating, we have quantified the effects of shock-induced microstructures on helium diffusion kinetics in well-characterized variably shocked zircon. We investigated samples from two impact structures, the Chicxulub multi-ring crater and Ries complex crater, to compare diffusion kinetics from structures with different size, age, and hydrothermal system longevity. Shock microstructures were characterized by backscattered-electron imaging prior to determining the He diffusion kinetics by prograde and retrograde fractional-release experiments via light-bulb furnace with incremental step-heating (10°C) from 300°C to 600°C. Next, we examine the internal interconnectivity and sizes of the diffusion domains by EBSD. While we found that zircon with few shock microstructures exhibited no marked deviation from helium diffusion kinetics of undamaged zircon, zircon grains with planar microstructures and granular textures are characterized by a dramatic decrease in helium retentivity due to the reduction in the effective domain size and the introduction of interconnected fast diffusion pathways. A subset of grains were ZHe dated and showed that less deformed grains yielded a weighted mean age within error of the accepted impact ages, while the grains with planar microstructures or granular textures gave systematically younger ages. These new diffusion data and ZHe ages demonstrate that highly shocked grains are unsuitable for ZHe impact crater dating. Therefore, detailed characterization of impact-induced microstructures is critical for determining accurate ZHe impact ages and offers the possibility of investigating post-impact hydrothermal circulation.

Zircon↗
NASA NTRS1975

Coupling of Helmholtz resonators to improve acoustic liners for turbofan engines at low frequency

An analytical and test program was conducted to evaluate means for increasing the effectiveness of low frequency sound absorbing liners for aircraft turbine engines. Three schemes for coupling low frequency absorber elements were considered. These schemes were analytically modeled and their impedance was predicted over a frequency range of 50 to 1,000 Hz. An optimum and two off-optimum designs of the most promising, a parallel coupled scheme, were fabricated and tested in a flow duct facility. Impedance measurements were in good agreement with predicted values and validated the procedure used to transform modeled parameters to hardware designs. Measurements of attenuation for panels of coupled resonators were consistent with predictions based on measured impedance. All coupled resonator panels tested showed an increase in peak attenuation of about 50% and an increase in attenuation bandwidth of one one-third octave band over that measured for an uncoupled panel. These attenuation characteristics equate to about 35% greater reduction in source perceived noise level (PNL), relative to the uncoupled panel, or a reduction in treatment length of about 24% for constant PNL reduction. The increased effectiveness of the coupled resonator concept for attenuation of low frequency broad spectrum noise is demonstrated.

Dean, L. W.↗
NASA NTRS2008

Electromagnetically Clean Solar Arrays

The term 'electromagnetically clean solar array' ('EMCSA') refers to a panel that contains a planar array of solar photovoltaic cells and that, in comparison with a functionally equivalent solar-array panel of a type heretofore used on spacecraft, (1) exhibits less electromagnetic interferences to and from other nearby electrical and electronic equipment and (2) can be manufactured at lower cost. The reduction of electromagnetic interferences is effected through a combination of (1) electrically conductive, electrically grounded shielding and (2) reduction of areas of current loops (in order to reduce magnetic moments). The reduction of cost is effected by designing the array to be fabricated as a more nearly unitary structure, using fewer components and fewer process steps. Although EMCSAs were conceived primarily for use on spacecraft they are also potentially advantageous for terrestrial applications in which there are requirements to limit electromagnetic interference. In a conventional solar panel of the type meant to be supplanted by an EMCSA panel, the wiring is normally located on the back side, separated from the cells, thereby giving rise to current loops having significant areas and, consequently, significant magnetic moments. Current-loop geometries are chosen in an effort to balance opposing magnetic moments to limit far-0field magnetic interactions, but the relatively large distances separating current loops makes full cancellation of magnetic fields problematic. The panel is assembled from bare photovoltaic cells by means of multiple sensitive process steps that contribute significantly to cost, especially if electomagnetic cleanliness is desired. The steps include applying a cover glass and electrical-interconnect-cell (CIC) sub-assemble, connecting the CIC subassemblies into strings of series-connected cells, laying down and adhesively bonding the strings onto a panel structure that has been made in a separate multi-step process, and mounting the wiring on the back of the panel. Each step increases the potential for occurrence of latent defects, loss of process control, and attrition of components. An EMCSA panel includes an integral cover made from a transparent material. The silicone cover supplants the individual cover glasses on the cells and serves as an additional unitary structural support that offers the advantage, relative to glass, of the robust, forgiving nature of the silcone material. The cover contains pockets that hold the solar cells in place during the lamination process. The cover is coated with indium tin oxide to make its surface electrically conductive, so that it serves as a contiguous, electrically grounded shield over the entire panel surface. The cells are mounted in proximity to metallic printed wiring. The painted-wiring layer comprises metal-film traces on a sheet of Kapton (or equivalent) polyimide. The traces include contact pads on one side of the sheet for interconnecting the cells. Return leads are on the opposite side of the sheet, positioned to form the return currents substantially as mirror images of, and in proximity to, the cell sheet currents, thereby minimizing magnetic moments. The printed-wiring arrangement mimics the back-wiring arrangement of conventional solar arrays, but the current-loop areas and the resulting magnetic moments are much smaller because the return-current paths are much closer to the solar-cell sheet currents. The contact pads are prepared with solder fo electrical and mechanical bonding to the cells. The pocketed cover/shield, the solar cells, the printed-wiring layer, an electrical bonding agent, a mechanical-bonding agent, a composite structural front-side face sheet, an aluminum honeycomb core, and a composite back-side face sheet are all assembled, then contact pads are soldered to the cells and the agents are cured in a single lamination process.

Stem, Theodore G.↗
NASA NTRS2011

Numerical Investigation of Rotorcraft Fuselage Drag Reduction Using Active Flow Control

The effectiveness of unsteady zero-net-mass-flux jets for fuselage drag reduction was evaluated numerically on a generic rotorcraft fuselage in forward flight with a rotor. Previous efforts have shown significant fuselage drag reduction using flow control for an isolated fuselage by experiment and numerical simulation. This work will evaluate a flow control strategy, that was originally developed on an isolated fuselage, in a more relevant environment that includes the effects of a rotor. Evaluation of different slot heights and jet velocity ratios were performed. Direct comparisons between an isolated fuselage and rotor/fuselage simulations were made showing similar flow control performance at a -3deg fuselage angle-of-attack condition. However, this was not the case for a -5deg angle-of-attack condition where the performance between the isolated fuselage and rotor/fuselage were different. The fuselage flow control resulted in a 17% drag reduction for a peak C(sub mu) of 0.0069 in a forward flight simulation where mu = 0:35 and CT/sigma = 0:08. The CFD flow control results also predicted a favorable 22% reduction of the fuselage download at this same condition, which can have beneficial compounding effects on the overall performance of the vehicle. This numerical investigation was performed in order to provide guidance for a future 1/3 scale wind tunnel experiment to be performed at the NASA 14-by 22-Foot Subsonic Tunnel.

Allan, Brian G.↗