SEARCH · Search NASA

Results for “SHEARING STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1999

A fluid--structure interaction finite element analysis of pulsatile blood flow through a compliant stenotic artery

A new model is used to analyze the fully coupled problem of pulsatile blood flow through a compliant, axisymmetric stenotic artery using the finite element method. The model uses large displacement and large strain theory for the solid, and the full Navier-Stokes equations for the fluid. The effect of increasing area reduction on fluid dynamic and structural stresses is presented. Results show that pressure drop, peak wall shear stress, and maximum principal stress in the lesion all increase dramatically as the area reduction in the stenosis is increased from 51 to 89 percent. Further reductions in stenosis cross-sectional area, however, produce relatively little additional change in these parameters due to a concomitant reduction in flow rate caused by the losses in the constriction. Inner wall hoop stretch amplitude just distal to the stenosis also increases with increasing stenosis severity, as downstream pressures are reduced to a physiological minimum. The contraction of the artery distal to the stenosis generates a significant compressive stress on the downstream shoulder of the lesion. Dynamic narrowing of the stenosis is also seen, further augmenting area constriction at times of peak flow. Pressure drop results are found to compare well to an experimentally based theoretical curve, despite the assumption of laminar flow.

Non-NASA Center↗

NASA NTRS1974

A note on the effect of bending stiffness of stringers attached to a plate with a crack

An infinite stringer partially bonded to a plate through a layer of adhesive is considered. The stringer had bending as well as longitudinal stiffness. The effect of the stringer's bending rigidity on the stress intensity factor at the tip of the crack is illustrated. Shear stress distribution between the plate and the stringer and the stress intensity factors are obtained from the solution of a system of Fredholm integral equations. The continuity of displacements along the line of bond is represented by the equations.

Arin, K.↗

NASA NTRS1975

A note on the effect of lateral bending stiffness of stringers attached to a plate with a crack

An infinite stringer which is assumed to be partially bonded to a plate through a layer of adhesive is considered. The stringer is assumed to have bending as well as longitudinal stiffness. The effect of the stringer's bending rigidity on the stress intensity factor at the tip of the crack is illustrated. Shear stress distribution between the plate and the stringer and the stress intensity factors will be obtained from the solution of a system of Fredholm integral equations which represent the continuity of displacements along the line of bond.

Arin, K.↗

NASA NTRS1976

A limiting analysis for edge effects in angle-ply laminates

A zeroth order solution for edge effects in angle ply composite laminates using perturbation techniques and a limiting free body approach was developed. The general method of solution for laminates is developed and then applied to the special case of a graphite/epoxy laminate. Interlaminar stress distributions are obtained as a function of the laminate thickness to width ratio h/b and compared to existing numerical results. The solution predicts stable, continuous stress distributions, determines finite maximum tensile interlaminar normal stress for two laminates, and provides mathematical evidence for singular interlaminar shear stresses.

Hsu, P. W.↗

NASA NTRS1983

The structure of a separating turbulent boundary layer. IV - Effects of periodic free-stream unsteadiness

Measurements were obtained of the sinusoidal unsteadiness of the free stream velocity during the separation of the turbulent boundary layer. Data were gathered by single wire and cross-wire, anemometry upstream of flow detachment, by laser Doppler velocimetry to detect the movement of the flow in small increments, and by a laser anemometer in the detached zone to measure turbulence and velocities. The study was restricted to a sinusoidal instability frequency of 0.61 and a ratio of oscillation amplitude to mean velocity of 0.3. Large amplitude and phase variations were found after the detachment, with unsteady effects producing hysteresis in the relationships between flow parameters. The detached shear layer decreased in thickness with increasing free-stream velocity and increases in the Reynolds shear stress. Deceleration of the free stream velocity caused thickening in the shear layer and upstream movement of the flow reversal location. The results are useful for studies of compressor blade and helicopter rotors in transition.

Simpson, R. L.↗

NASA NTRS1985

A three-dimensional turbulent separated flow and related mesurements

The applicability of and the limits on the applicability of 11 near wall similarity laws characterizing three-dimensional turbulent boundary layer flows were determined. A direct force sensing local wall shear stress meter was used in both pressure-driven and shear-driven three-dimensional turbulent boundary layers, together with extensive mean velocity field and wall pressure field data. This resulted in a relatively large number of graphical comparisons of the predictive ability of 10 of these 11 similarity models relative to measured data over a wide range of flow conditions. Documentation of a complex, separated three-dimensional turbulent flow as a standard test case for evaluating the predictive ability of numerical codes solving such flows is presented.

Pierce, F. J.↗

NASA NTRS1989

Measurement of terms and parameters in turbulent models

Experimental measurements of the mean and turbulent velocity field in a water flow, turn-around-duct is documented. The small radius of curvature duct experiments were made over a range of Reynolds numbers (based on a duct height of 10 cm) from 70,000 to 500,000. For this particular channel, the flow is dominated by the inertia forces. Use of the local bulk velocity to non-dimensionalize the local velocity was found to limit Reynolds number effects to the regions very close to the wall. Only secondary effects on the flow field were observed when the inlet or exit boundary conditions were altered. The flow over the central two-thirds of the channel was two-dimensional. Mean tangetial and radial velocities, streamlines, pressure distributions, surface shear stress; tangential, radial and lateral turbulent velocities and the Reynolds turbulent shear values are tabulated in other reports. It is evident from the experimental study that a complex numerical modeling technique must be developed to predict the flow in the turn-around-duct. The model must be able to predict relaminarization along the inner-convex-wall. It must also allow for the major increase in turbulence produced by the outer-concave-wall.

Sandborn, Virgil A.↗

NASA NTRS1990

Active turbulence control in wallbounded flow using direct numerical simulations

An exploratory study of concepts for active control of turbulent boundary layers using the direct numerical simulation technique was performed. Significant drag reduction was achieved when the surface boundary condition was modified such that it could suppress the large-scale structures present in the wall region. This was achieved by prescribing the normal component of velocity at the wall to be 180 deg out of phase with the normal velocity slightly above the wall at each instant. The drag reduction was accompanied with significant reduction in the intensity of the wall-layer structures and reductions in the magnitude of Reynolds stresses throughout the flow. Suitability of wall-pressure and shear-stress fluctuations for detection of flow structures above the wall was examined. A preliminary result obtained by applying the present control strategy to a transitional flow is also briefly described, from which one can infer a possible linkage between the control strategy and flow stability.

Kim, J.↗

NASA NTRS2009

Refined Zigzag Theory for Laminated Composite and Sandwich Plates

A refined zigzag theory is presented for laminated-composite and sandwich plates that includes the kinematics of first-order shear deformation theory as its baseline. The theory is variationally consistent and is derived from the virtual work principle. Novel piecewise-linear zigzag functions that provide a more realistic representation of the deformation states of transverse-shear-flexible plates than other similar theories are used. The formulation does not enforce full continuity of the transverse shear stresses across the plate s thickness, yet is robust. Transverse-shear correction factors are not required to yield accurate results. The theory is devoid of the shortcomings inherent in the previous zigzag theories including shear-force inconsistency and difficulties in simulating clamped boundary conditions, which have greatly limited the accuracy of these theories. This new theory requires only C(sup 0)-continuous kinematic approximations and is perfectly suited for developing computationally efficient finite elements. The theory should be useful for obtaining relatively efficient, accurate estimates of structural response needed to design high-performance load-bearing aerospace structures.

Tessler, Alexander↗

NASA NTRS2018

Reynolds-Stress Budgets in an Impinging Shock Wave/Boundary-Layer Interaction

Implicit large-eddy simulation (ILES) of a shock wave/boundary-layer interaction (SBLI) was performed. Comparisons with experimental data showed a sensitivity of the current prediction to the modeling of the sidewalls. This was found to be common among various computational studies in the literature where periodic boundary conditions were used in the spanwise direction, as was the case in the present work. Thus, although the experiment was quasi-two-dimensional, the present simulation was determined to be two-dimensional. Quantities present in the exact equation of the Reynolds-stress transport, i.e., production, molecular diffusion, turbulent transport, pressure diffusion, pressure strain, dissipation, and turbulent mass flux were calculated. Reynolds-stress budgets were compared with past large-eddy simulation and direct numerical simulation datasets in the undisturbed portion of the turbulent boundary layer to validate the current approach. The budgets in SBLI showed the growth in the production term for the primary normal stress and energy transfer mechanism was led by the pressure strain term in the secondary normal stresses. The pressure diffusion term, commonly assumed as negligible by turbulence model developers, was shown to be small but non-zero in the normal stress budgets, however it played a key role in the primary shear stress budget.

shock wave/boundary-layer interactio↗

DOE OSTI2026

Controlling Deformation in Al/Ti: How Interface Roughness and Orientation Drive Bimetal Mechanics

The microstructural characteristics and morphology of interfaces in metals can be crucial in governing the initiation of plasticity and early deformation mechanisms under extreme conditions. During high-strain-rate deformation, these interfaces significantly affect dislocation nucleation, twinning, and other mechanisms that directly impact material strength and failure. Despite their importance, a substantial knowledge gap remains between the observed macroscopic material behavior and the underlying role of bimetal interfaces in plasticity initiation. Here, to address this gap, large-scale molecular dynamics simulations are performed on Al/Ti bimetal structures to examine the effect of interface characteristics on the onset of plasticity under uniaxial compression. Specifically, this study investigates how interface roughness (flat vs waveform interfaces) modifies the initiation of plastic events in the microstructure. Atomistic simulations indicate that interface roughness (a microscopic behavior) reduces the stress required for dislocation nucleation, thereby reducing the peak stress relative to a flat interface. For the square interface, the step height strongly influences plasticity initiation by setting the separation of locally flat regions. Varying the interface rotation relative to the loading direction (macroscopic behavior) reveals that the peak stress for both flat and waveform interfaces initially decreases and then increases with rotation, accompanied by a shift in dominant mechanisms—from Al twinning (flat) to interface sliding and Ti-dominated phase transformation and twinning at lower angles. The change in the stress-strain slope during initial compression reflects how rotation alters the resolved shear stress and activates different slip systems. Overall, the study provides valuable insights into the role of bimetal interfaces in controlling plasticity initiation and early deformation pathways for Al/Ti under extreme loading conditions.

36 MATERIALS SCIENCE↗

NASA NTRS1982

Turbulence modeling for computational aerodynamics

The status of turbulence modeling for external aerodynamic flows is reviewed, and closure concepts for the compressible form of the Reynolds-averaged Navier-Stokes equations are briefly outlined to establish a framework for comparison. The importance of experimental requirements for developing and verifying turbulence models is emphasized. Attention is then given to three important flow categories: attached flows, separating and reattaching flows, and trailing-edge flows. Examples of comparisons between experiments and computations for twoand three-dimensional flows are presented to illustrate the status of modeling. It is shown that, for most two-dimensional attached flows, eddy viscosity concepts will probably be adequate. For attached three-dimensional flows, however, eddy-viscosity and Reynolds-stress models are both deficient, failing to predict the proper surface shear-stress in rapidly skewing boundary layers, regardless of whether they are pressure driven or strain driven.

Marvin, J. G.↗

NASA NTRS1982

Moving cracks in layered composites

A three-layered composite with a crack spreading in the center layer has been analytically examined to evaluate the effect of material nonhomogeneity on a constant velocity crack. Two different loading characteristics are considered. In the first case, crack motion is maintained by uniform tensile stresses. In the other, crack deformation is caused by anti-plane shear stresses. Galilean transformation and Fourier sine and cosine transforms are used to determine dynamic crack tip stress fields. Standard Fredholm integral equations yield the dynamic stress intensity factors. The results show that the intensity of local dynamic stresses increases or decreases with crack length to layer thickness as a function of the relative magnitudes of the adjoining layer's material properties. Crack speed tends to increase the effect of material nonhomogeneity.

Sih, G. C.↗

NASA NTRS1983

Thermal stresses in bonded solar cells - The effect of the adhesive layer

A two-dimensional, rectangular model of a proposed solar cell structure is analyzed as two plate elements bonded with an elastic continuum. The governing equations are formulated using the principle of minimum potential energy, with displacement components that vary linearly through the thickness of the adhesive layer. An approximate solution is constructed for a particular class of material properties and is characterized by a boundary layer near the unloaded edge. Both interface stress components achieve their largest values at the edge, and the maximum shear stress is independent of the Young's Modulus of the substrate.

Williams, H. E.↗

NASA NTRS1984

An experimental study of a vortex/mixing-layer interaction

The first phase of a subsonic experimental investigation of the structure of a longitudinal vortex and the effect of the vortex on a two-stream turbulent mixing layer has been completed. A stable and well-defined longitudinal vortex was generated by mounting a half-delta-wing vortex generator in the wind-tunnel settling chamber. A detailed flow-visualization study, using the smoke-laser technique, was conducted, and X-wire probes were used to measure the mean-flow and turbulence quantities. At the upstream locations, the vortex was found to develop some normal stresses within the core region. The vortex also induced strong secondary motions and small increases in the normal stresses within the mixing layer. The normal stresses then combined with the appropriate mean-velocity gradients to generate shear stresses farther downstream. The results indicate that more sophisticated turbulence models will have to be developed if such complex interactions are to be computed accurately.

Mehta, R. D.↗

NASA NTRS1985

The distortion of a supersonic turbulent boundary layer by bulk compression and surface curvature

An experimental investigation is conducted of the effects of bulk compression and streamline curvature on a turbulent supersonic boundary layer whose incoming Mach number is 2.87. Two different, constant-radius curved wall models were used; the total turning angle in both cases was fixed at 8 deg. While the amplification of the normal stress was approximately the same in both models, the amplification of the shear stress was greater in the one with delta(o)/R value 0.1 than in the model with a value of 0.02. The flow over the latter model appears to be especially complex.

Smits, A. J.↗

NASA NTRS1986

A refined mixed shear flexible finite element for the nonlinear analysis of laminated plates

The present study is concerned with the development of a mixed shear flexible finite element with relaxed continuity for the geometrically linear and nonlinear analysis of laminated anisotropic plates. The formulation of the element is based on a refined higher-order theory. This theory satisfies the zero transverse shear stress boundary conditions on the top and bottom faces of the plate. Shear correction coefficients are not needed. The developed element consists of 11 degrees-of-freedom per node, taking into account three displacements, two rotations, and six moment resultants. An evaluation of the element is conducted with respect to the accuracy obtained in the bending of laminated anistropic rectangular plates with different lamination schemes, loadings, and boundary conditions.

Putcha, N. S.↗

NASA NTRS1988

Accelerated fatigue crack growth behavior of PWA 1480 single crystal alloy and its dependence on the deformation mode

An investigation of the fatigue crack growth (FCG) behavior of PWA 1480 single crystal nickel base superalloy was conducted. Typical Paris region behavior was observed above a delta K of 8 MPa sq rt of m. However, below that stress intensity range, the alloy exhibited highly unusual behavior. This behavior consisted of a region where the crack growth rate became essentially independent of the applied stress intensity. The transition in the FCG behavior was related to a change in the observed crack growth mechanisms. In the Paris region, fatigue failure occurred along (111) facets; however, at the lower stress intensities, (001) fatigue failure was observed. A mechanism was proposed, based on barriers to dislocation motion, to explain the changes in the observed FCG behavior. The FCG data were also evaluated in terms of a recently proposed stress intensity parameter, K sub rss. This parameter, based on the resolved shear stresses on the slip planes, quantified the crack driving force as well as the mode I delta K, and at the same time was also able to predict the microscopic crack path under different stress states.

Telesman, Jack↗