Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Analysis of Spiral Bevel Gearing

Program generalized for automated finite-element-method model generation. Tedious task of finite-element-method (FEM) model preparation greatly reduced by development of preprocessing program for automated model generation. Utility of program, including ability to rapidly evaluate parametric changes, demonstrated for spiral, helical, and spiral bevel gearing. Postprocessing program also developed, aids in review and interpretation of calculated FEM stresses.

Drago, R. J.↗

Turbulent boundary layers with secondary flow

An experimental analysis of the boundary layer on a plane wall, along which the flow occurs, whose potential flow lines are curved in plane parallel to the wall is discussed. According to the equation frequently applied to boundary layers in a plane flow, which is usually obtained by using the pulse law, a generalization is derived which is valid for boundary layers with spatial flow. The wall shear stresses were calculated with this equation.

Grushwitz, E.↗

Rheology of glacier ice

A new method for calculating the stress field in bounded ice shelves is used to compare strain rate and deviatoric stress on the Ross Ice Shelf, Antarctica. The analysis shows that strain rate (per second) increases as the third power of deviatoric stress (in newtons/sq meter), with a constant of proportionality equal to 2.3 x 10 to the -25th.

Jezek, K. C.↗

Stress analyses of B-52 pylon hooks

The NASTRAN finite element computer program was used in the two dimensional stress analysis of B-52 carrier aircraft pylon hooks: (1) old rear hook (which failed), (2) new rear hook (improved geometry), (3) new DAST rear hook (derated geometry), and (4) front hook. NASTRAN model meshes were generated by the aid of PATRAN-G computer program. Brittle limit loads for all the four hooks were established. The critical stress level calculated from NASTRAN agrees reasonably well with the values predicted from the fracture mechanics for the failed old rear hook.

Ko, W. L.↗

Dynamic fracture mechanics

Dynamic fracture and crack propagation concepts for ductile materials are reviewed. The equations for calculating dynamic stress integrity and the dynamic energy release rate in order to study dynamic crack propagation are provided. The stress intensity factor versus crack velocity relation is investigated. The uses of optical experimental techniques and finite element methods for fracture analyses are described. The fracture criteria for a rapidly propagating crack under mixed mode conditions are discussed; crack extension and fracture criteria under combined tension and shear loading are based on maximum circumferential stress or energy criteria such as strain energy density. The development and use of a Dugdale model and finite element models to represent crack and fracture dynamics are examined.

Kobayashi, A. S.↗

ANISAP: A three-dimensional finite element program for laminated composites subjected to mechanical loading

ANISAP is a 3-D finite element FORTRAN 77 computer code for linear elastic, small strain, analysis of laminated composites with arbitrary geometry including free edges and holes. Individual layers may be isotropic or transversely isotropic in material principal coordinates; individual layers may be rotated off-axis about a global z-axis. The laminate may be a hybrid. Three different isoparametric elements, variable order of gaussian integration, calculation of stresses at element boundaries, and loading by either nodal displacement of forces are included in the program capability. Post processing capability includes failure analysis using the tensor polynominal failure criterion.

Burns, S. W.↗

Mechanical behavior of thermal barrier coatings for gas turbine blades

Plasma-sprayed thermal barrier coatings (TBCs) will enable turbine components to operate at higher temperatures and lower cooling gas flow rates; thereby improving their efficiency. Future developments are limited by precise knowledge of the material properties and failure mechanisms of the coating system. Details of this nature are needed for realistic modeling of the coating system which will, in turn, promote advancements in coating technology. Complementary experiments and analytical modeling which were undertaken in order to define and measure the important failure processes for plasma-sprayed coatings are presented. The experimental portion includes two different tests which were developed to measure coating properties. These are termed tensile adhesion and acoustic emission tests. The analytical modeling section details a finite element method which was used to calculate the stress distribution in the coating system. Some preliminary results are presented.

Berndt, C. C.↗

Influence of large deflection and transverse shear on random response of rectangular symmetric composite laminates to acoustic loads

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived accounting for von Karman strains. The effect of transverse shear is included in the formulation and the rotatory inertia effect is ignored. Using a single-mode Galerkin procedure the nonlinear modal equation is obtained. Direct equivalent linearization is employed. The response of acoustic excitation on moderately thick composite panels is studied. Further, the effects of transverse shear on large deflection vibration of laminates under random excitation are studied. Mean-square deflection and mean-square inplane stresses are obtained for some symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for simply supported plate. The analogous equations for a clamped case are given in the appendix.

Mei, Chuh↗

An integrated finite element model of edge-delamination analysis for laminates due to tension, bending, and torsion loads

A two-dimensional finite-element model has been developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to various loads. This paper addresses the formulation, implementation, and verification of a suitable 'element for uniaxial tension, bending, and torsion', as well as parametric studies of the interlaminar stresses and strain energy release rates for various composite laminates. The study concentrates on establishing relationships of GI, GII, and GIII as functions of crack length and stacking sequence in laminates due to bending. Preliminary results of laminates subjected to torsional loads are included to increase the applicability and completeness of the present formulation.

Chan, W. S.↗

Effects of large deflection and transverse shear on response of rectangular symmetric composite laminates subjected to acoustic excitation

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived accounting for von Karman strains. The effect of transverse shear is included in the formulation. Using a single-mode Galerkin procedure, the nonlinear modal equation is obtained. The direct equivalent linearization method is employed for solution of this equation. The response to acoustic excitation of moderately thick composite panels is studied. Further, the effects of transverse shear on large deflection vibration of laminates under random excitation are studied. Mean-square deflections and mean-square inplane stresses are obtained for symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for simply supported plates. The analogous equations for a clamped case are also obtained.

Mei, Chuh↗

Analysis and test evaluation of the dynamic response and stability of three advanced turboprop models at low forward speed

Results of wind tunnel tests at low forward speed for blade dynamic response and stability of three 62.2 cm (24.5 in) diameter models of the Prop-Fan, advanced turboprop, are presented. Measurements of dynamic response were made with the rotors mounted on an isolated nacelle, with varying tilt for nonuniform inflow. Low speed stall flutter tests were conducted at Mach numbers from 0.0 to 0.35. Measurements are compared to Eigen-solution flutter boundaries. Calculated 1P stress response agrees favorably with experiment. Predicted stall flutter boundaries correlate well with measured high stress regions. Stall flutter is significantly reduced by increased blade sweep. Susceptibility to stall flutter decreases rapidly with forward speed.

Smith, Arthur F.↗

Stress modeling of microdiaphragm pressure sensors

A finite element program analysis was used to model the stress distribution of two monocrystalline silicon diaphragm pressure sensors. One configuration consists of an anisotropically backside etched diaphragm into a 250 micron thick, (100) oriented, silicon wafer. The diaphragm and total chip dimensions are given. The device is rigidly clamped on the back to a support substrate. Another configuration consists of a monocrystalline, (100), microdiaphragm which is formed on top of the wafer and whose area is reduced by a factor of 25 over the first configuration. The diaphragm is rigidly clamped to the silicon wafer. The stresses were calculated at a gauge pressure of 300 mm Hg and used to estimate the piezoresistive responses of resistor elements which were placed parallel and perpendicular near the diaphragm edges.

Tack, P. C.↗

An analytical and experimental investigation of edge delamination in laminates subjected to tension, bending, and torsion

An integrated two-dimensional finite element was developed to calculate interlaminar stresses and strain energy release rates for the study of delamination in composite laminates subjected to uniaxial tension, bending, and torsion loads. Addressed are the formulation, implementation, and verification of the model. Parametric studies were conducted on the effect of Poisson's ratio mismatch between plies and the stacking sequence on interlaminar stress, and on the effect of delamination opening height and delamination length, due to bending, on strain energy release rate for various laminates. A comparison of strain energy release rates in all-graphite and graphite/glass hybrid laminates is included. The preliminary results of laminates subjected to torsion are also included. Fatigue tension tests were conducted on Mode 1 and mixed mode edge-delamination coupons to establish the relationship between fatigue load vs. onset of delamination cycle. The effect on the fatigue delamination onset of different frequencies (1 and 5 Hz) was investigated for glass, graphite,and their hybrid laminates. Although a 20 percent increase in the static onset-of-delamination strength and a 10 percent increase in ultimate strength resulted from hybridizing the all-graphite laminate with a 90 deg glass ply, the fatigue onset is lower in the hybrid laminate than in the all-graphite laminate.

Chan, Wen S.↗

Simulated impact damage in a thick graphite/epoxy laminate using spherical indenters

The extent of fiber damage due to low-velocity impacts was determined for very thick graphite/epoxy laminates. The impacts were simulated by pressing spherical indenters against the laminates. After the forces were applied, the laminate was cut into smaller pieces so that each piece contained a test site. Then the pieces were deplied and the individual plies were examined to determine the extent of fiber damage. Broken fibers were found in the outer layers directly beneath the contact site. The locus of broken fibers resembled cracks. The cracks were more or less oriented in the direction of the fibers in the contiguous layers. The maximum length and depth of the cracks increased with increasing contact pressure and indenter diameter. The length and depth of the cracks were also predicted using maximum compression and shear stress criteria. The internal stresses were calculated using Hertz's law and Love's solution for pressure applied on part of the boundary of a semi-infinite body. The predictions and measurements were in good agreement.

Poe, C. C., Jr.↗

Effects of transverse shear on large deflection random response of symmetric composite laminates with mixed boundary conditions

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived considering von Karman strains and transverse shear effects. Using a single-mode Galerkin procedure, the nonlinear modal equation is obtained. The direct equivalent linearization method is employed for solution of this equation. The effects of transverse shear on large deflection vibration of laminated plates with mixed boundary support conditions under random excitation are studied. Mean-square deflections and mean-square inplane strains are obtained for symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for plates with two opposing edges simply supported and the remaining edges clamped.

Prasad, C. B.↗

Mechanical behavior of fiber reinforced SiC/RBSN ceramic matrix composites: Theory and experiment

The mechanical behavior of continuous fiber reinforced SiC/RBSN (Reaction Bonded Silicon Nitride) composites with various fiber contents is evaluated. Both catastrophic and noncatastrophic failures are observed in tensile specimens. Damage and failure mechanisms are identified via in-situ monitoring using NDE (nondestructive evaluation) techniques through the loading history. Effects of fiber/matrix interface debonding (splitting) parallel to fibers are discussed. Statistical failure behavior of fibers is also observed, especially when the interface is weak. Micromechanical models incorporating residual stresses to calculate the critical matrix cracking strength, ultimate strength, and work of pull-out are reviewed and used to predict composite response. For selected test problems, experimental measurements are compared to analytical predictions.

Chulya, Abhisak↗

The surface and through crack problems in layered orthotropic plates

An analytical method is developed for a relatively accurate calculation of Stress Intensity Factors in a laminated orthotropic plate containing a through or part-through crack. The laminated plate is assumed to be under bending or membrane loading and the mode 1 problem is considered. First three transverse shear deformation plate theories (Mindlin's displacement based first-order theory, Reissner's stress-based first-order theory, and a simple-higher order theory due to Reddy) are reviewed and examined for homogeneous, laminated and heterogeneous orthotropic plates. Based on a general linear laminated plate theory, a method by which the stress intensity factors can be obtained in orthotropic laminated and heterogeneous plates with a through crack is developed. Examples are given for both symmetrically and unsymmetrically laminated plates and the effects of various material properties on the stress intensity factors are studied. In order to implement the line-spring model which is used later to study the surface crack problem, the corresponding plane elasticity problem of a two-bonded orthotropic plated containing a crack perpendicular to the interface is also considered. Three different crack profiles: an internal crack, an edge crack, and a crack terminating at the interface are considered. The effect of the different material combinations, geometries, and material orthotropy on the stress intensity factors and on the power of stress singularity for a crack terminating at the interface is fully examined. The Line Spring model of Rice and Levy is used for the part-through crack problem. The surface crack is assumed to lie in one of the two-layered laminated orthotropic plates due to the limitation of the available plane strain results. All problems considered are of the mixed boundary value type and are reduced to Cauchy type of singular integral equations which are then solved numerically.

Erdogan, Fazil↗

An improved error analysis of finite element solutions for postbuckled plates

The accurate calculation of stresses at boundaries and interfaces where FEM analysis may be unreliable is presently undertaken by an error analysis that derives a continuous approximation to discrete finite-element data, which can be differentiated to compute continuous stresses for component-failure predictions. An evaluation is conducted of this approximation in the context of the nonlinear PDEs. A novel interpolation formula which is a simple modification of the double Fourier sine series is used to reduce truncation errors near the rectangular plate boundary by means of an 'extended grid'. Results are presented from a FEM solution, a conventional double-Fourier series' continuous approximation, and a solution applying interpolation on the extended grid, which yields superior convergence properties near the plate boundaries.

Sistla, Rajaram↗