Search NASA⌕ Search

SEARCH · Search NASA

Results for “Static”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1951

An analysis of the effects of aeroelasticity on static longitudinal stability and control of a swept-back-wing airplane

A theoretical analysis of the effects of aeroelasticity on the stick-fixed static longitudinal stability and elevator angle required for balance of an airplane is presented together with calculated effects for a swept-wing bomber of relatively high flexibility. Although large changes in stability due to certain parameters are indicated for the example airplane, the over-all stability change after considering all parameters was quite small, compared to the individual effects, due to the counterbalancing of wing and tail contributions. The effect of flexibility on longitudinal control for the example airplane was found to be of little real importance.

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS1951

Low-speed static longitudinal and lateral stability characteristics of two low-aspect-ratio wings cambered and twisted to provide a uniform load at a supersonic flight condition

A delta wing and a tapered sweptback wing of aspect ratios 1.56 and 2.00, respectively, both of which were cambered and twisted so as to provide a uniform load distribution for a supersonic flight condition, were tested in combination with a fuselage at Reynolds numbers between 384,000 and 1,550,000 in order to determine the low-speed lift-drag and static stability characteristics of such wings.

REYNOLDS NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1927

Approximation method for determining the static stability of a monoplane glider

The calculations in this paper afford an approximate solution of the static stability. A derivation of the formulas for moment coefficient of a wing, moment coefficient of elevator, and the total moment of the combined wing and elevator and the moment coefficient with reference to the center of gravity are provided.

AIRFOILS - GLIDERS↗
NASA NTRS1951

Influence of static longitudinal stability on the behavior of airplanes in gusts

The equations of motion for an airplane penetrating a gust are derived using a few simplifying assumptions. Calculations of loads for different static longitudinal stability on two German airplane models, HC 45 and HS 122, are compared with flight tests. Good agreement is obtained between the trend of the flight tests and the calculated values; however no absolute comparison was possible between the flight tests and calculations.

LOADS, GUST - HENSCHEL 122↗
NASA NTRS2016

Non-Contacting Finger Seals Static Performance Test Results at Ambient and High Temperatures

The non-contacting finger seal is an advanced seal concept with potential to reduce specific fuel consumption in gas turbine engines by 2 to 3 percent with little to no wear of the seal or rotor. Static performance tests and bind-up tests of eight different non-contacting finger seal configurations were conducted in air at pressure differentials up to 689.4 kPa and temperatures up to 922 K. Four of the seals tested were designed to have lift pads concentric to a herringbone-grooved rotor which generates hydrodynamic lift when rotating. The remaining seals were tested with a smooth rotor; one seal had a circumferential taper and one had an axial taper on the lift pad inner diameter to create hydrodynamic lift during rotation. The effects of the aft finger axial thickness and of the forward finger inner diameter on leakage performance were investigated as well and compared to analytical predictions.

static tests↗