Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Heat generation in aircraft tires

A method was developed for calculating the internal temperature distribution in an aircraft tire while free rolling under load. The method uses an approximate stress analysis of each point in the tire as it rolls through the contact patch, and from this stress change the mechanical work done on each volume element may be obtained and converted into a heat release rate through a knowledge of material characteristics. The tire cross-section is then considered as a body with internal heat generation, and the diffusion equation is solved numerically with appropriate boundary conditions of the wheel and runway surface. Comparison with data obtained with buried thermocouples in tires shows good agreement.

Clark, S. K.↗
NASA NTRS1986

Design and analysis of a keel latch for use on the Hubble Space Telescope

The mechanical design of the keel latch is discussed, as well as the stress analysis of the keel latch. Background information; mechanical design requirements; some of the initial design considerations; the design considerations that led to the selection of the final design; the mechanics of the final design; testing that has been and will be accomplished to verify that design requirements have been met; and future tests are discussed.

Calvert, John↗
NASA NTRS1982

Dynamic and static modeling of the shuttle orbiter's thermal protection system

The dynamic and static analysis methods used to model the nonlinear structural behavior of the Shuttle Orbiter's tile/pad thermal protection system are discussed. The structural evaluation of the tile/pad system is complicated by the nonlinear stiffening, hysteresis and viscosity exhibited by the pad material. Application of the analysis to square tiles subject to sinusoidal and random excitation is presented along with appropriate test data. Correlation is considered good. In order to treat the stress analysis of thousands of individual tiles, a nonlinear static analysis was developed which utilizes equivalent static loads derived from the dynamic environment. Tensile stress at the bondline is examined in thousands of unique tiles.

Housner, J. M.↗
NASA NTRS1979

Photoelastic studies of advanced lap joint concept

Photoelasticity was introduced as a quantitative tool in the experimental stress analysis of anisotropic birefringent composite model materials. The investigation was divided into three parts: (1) separation of principal stresses or strains, (2) photoelastic calibration, and (3) development of model-prototype relations.

Prabhakaran, R.↗
NASA NTRS1986

Progressive fracture of fiber composites

Refined models and procedures are described for determining progressive composite fracture in graphite/epoxy angleplied laminates. Unique Lewis Research Center capabilities are utilized including the Real-Time Ultrasonic C-San (RUSCAN) experimental facility and the Composite Durability Structural Analysis (CODSTRAN) computer code. CODSTRAN is used to predict the fracture progression based on composite mechanics, finite element stress analysis, and fracture criteria modules. The RUSCAN facility, CODSTRAN computer code, and scanning electron microscope are used to determine durability and identify failure mechanisms in graphite/epoxy coomposites. Results indicate that RUSCAN/CODSTRAN is an effective method of Studying progressive fracture of composites.

Irvine, T. B.↗
DOE OSTI2024

SOSAT: Geohazard Risk Assessment in Carbon Sequestration Operations

Like all operations in which fluids are injected into the subsurface, geologic carbon storage (GCS) presents inherit risks that must be assessed and mitigated to successfully deploy such technology in the field. For example, alterations to pore pressure and the stress state due to fluid injection may trigger certain geohazards, such as potential fault activation and induced seismicity or unintentional hydraulic fracturing. Here we present capabilities for assessing these potential risks using the State of Stress Analysis Tool (SOSAT): a Python library and web-based application capable of probabilistically estimating the subsurface state of stress informed by various field observations. Using posterior distributions of principal stress components, SOSAT can assess the risk of fault activation within the injection formation for either a critically oriented fault or a fault with a user-prescribed orientation. Additionally, SOSAT can estimate the probability of unintentional hydraulic fracturing of the intact reservoir rock. Here, we demonstrate these SOSAT capabilities using a hypothetical GCS site. This type of risk assessment can assist with the effective deployment of GCS technology in the field by informing safe design and management practices.

Haagenson, Ryan J.↗
NASA NTRS1978

Summary of static load test of the Mod-0 blade

A static load test was performed on the spare Mod-0 wind turbine blade to define load transfer at the root end of the blade, and to validate stress analysis of this particular type of blade construction (frame and stringer). Analysis of the load transfer from the airfoil skin to the shank tube predicted a step change in spanwise stress in the airfoil skin at station 81.5 inches (STA 81.5). For flatwise bending a 40% reduction in spanwise stress was predicted, and for edgewise bending a 6% reduction. Experimental results verified the 40% reduction for flatwise bending, but indicated about a 30% reduction for edgewise bending.

Miller, D. R.↗
NASA NTRS1981

Determination of principal stress in birefringent composites by hole-drilling method

The application of transmission photoelasticity to stress analysis of composite materials is discussed.The method consists in drilling very small holes at points where the state of stress has to be determined. Experiments are described which verify the theoretical predicitons. The limitations of the method are discussed and it is concluded that valuable information concerning the state of stress in a composite model can be obtained through the suggested method.

Prabhakaran, R.↗
NASA NTRS1981

Finite element analysis of instability related delamination growth

Instability-related growth of through-width delaminations in laminated coupons was investigated analytically and experimentally. In the analytical effort, a geometrically nonlinear finite-element stress analysis was used, and the numerical results were compared with exact solutions. In addition, measured lateral deflections of postbuckled through-width delaminations were compared with predicted deflections. Lateral deflections, stress distributions, and strain energy release rates were calculated for various delamination lengths, delamination depths, and applied loads. Delamination growth rates observed for unidirectional graphite/epoxy bonded to aluminum were qualitatively correlated with calculated strain-energy release rates and it was found that the Mode I component of energy release dominates the growth process.

Whitcomb, J. D.↗
NASA NTRS1984

Investigation of the HPFTP first stage impeller crack

The occurrence of a crack in the HPFTP first stage impeller of pump 2608 R2 during test 750-245 prompted this analysis to examine possible causes of the failure. Preliminary analysis, using an existing NASTRAN model of the impeller, showed a deficiency in the model's ability to reliably calculate stress in the area of concern (outboard edge of the impeller shroud). A new NASTRAN model was constructed to better define the stress state in the area of crack initiations. Static stress analysis and normal models analysis were performed on the new model. Results are presented.

Source record↗
NASA NTRS1991

Tensile deformation damage in SiC reinforced Ti-15V-3Cr-3Al-3Sn

The damage mechanisms of a laminated, continuous SiC fiber reinforced Ti-15V-3Cr-3Al-3Sn (Ti-15-3) composite were investigated. Specimens consisting of unidirectional as well as cross-ply laminates were pulled in tension to failure at room temperature and 427 C and subsequently examined metallographically. Selected specimens were interrupted at various strain increments and examined to document the development of damage. When possible, a micromechanical stress analysis was performed to aid in the explanation of the observed damage. The analyses provide average constituent microstresses and laminate stresses and strains. It was found that the damage states were dependent upon the fiber architecture.

Lerch, Bradley A.↗
NASA NTRS1983

Burner liner thermal/structural load modelling

The objective of this program is to develop a thermal data transfer computer program module for the burner liner thermal structural load modeling program. This will be accomplished by (1) reviewing existing methodologies for thermal data transfer and selecting three heat transfer codes for application in this program; (2) evaluating the selected codes to establish criteria for developing a computer program module to transfer thermal data from the heat transfer codes to selected stress analysis codes; (3) developing the automated thermal load transfer module; and (4) verifying and documenting the module. In aircraft turbine engine hot section components, cyclic thermal stresses are the most important damage mechanism. Consequently, accurate and reliable prediction of thermal loads is essential to improving durability. To achieve this goal, a considerable effort over the past 20 years has been devoted to the acquisition of engine temperature test data, as well as the development of accurate, reliable, and efficient computer codes for the prediction of steady state and transient temperatures and for the calculation of elastic and inelastic cyclic stresses and strains in hot section components. There is a need for continued development of these codes, because the availability of more accurate analysis techniques for complex configurations has enabled engine designers to use more sophisticated designs to achieve higher cycle efficiency and reduce weight.

Maffeo, R. J.↗
NASA NTRS1992

Improved inhomogeneous finite elements for fabric reinforced composite mechanics analysis

There is a need to do routine stress/failure analysis of fabric reinforced composite microstructures to provide additional confidence in critical applications and guide materials development. Conventional methods of 3-D stress analysis are time consuming to set up, run and interpret. A need exists for simpler methods of modeling these structures and analyzing the models. The principal difficulty is the discrete element mesh generation problem. Inhomogeneous finite elements are worth investigating for application to these problems because they eliminate the mesh generation problem. However, there are penalties associated with these elements. Their convergence rates can be slow compared to homogeneous elements. Also, there is no accepted method for obtaining detailed stresses in the constituent materials of each element. This paper shows that the convergence rate can be significantly improved by a simple device which substitutes homogeneous elements for the inhomogeneous ones. The device is shown to work well in simple one and two dimensional problems. However, demonstration of the application to more complex two and three dimensional problems remains to be done. Work is also progressing toward more realistic fabric microstructural geometries.

Foye, R. L.↗
NASA NTRS1967

Computer program simplifies design of rotating components of turbomachinery

Digital computer program performs stress analysis and burst speed calculations on rotating axisymmetric turbomachinery components. The computer printout contains the displacement of each nodal point, the stress at the center of each element, the average tangential stress within the component, and the burst speed.

Lefevre, J. C.↗
NASA NTRS1983

Progressive fracture of fiber composites

Refined models and procedures are described for determining progressive composite fracture in graphite/epoxy angleplied laminates. Lewis Research Center capabilities are utilized including the Real Time Ultrasonic C Scan (RUSCAN) experimental facility and the Composite Durability Structural Analysis (CODSTRAN) computer code. The CODSTRAN computer code is used to predict the fracture progression based on composite mechanics, finite element stress analysis, and fracture criteria modules. The RUSCAN facility, CODSTRAN computer code, and scanning electron microscope are used to determine durability and identify failure mechanisms in graphite/epoxy composites.

Irvin, T. B.↗
NASA NTRS1998

Comprehensive Structural Dynamic Analysis of the SSME/AT Fuel Pump First-Stage Turbine Blade

A detailed structural dynamic analysis of the Pratt & Whitney high-pressure fuel pump first-stage turbine blades has been performed to identify the cause of the tip cracking found in the turbomachinery in November 1997. The analysis was also used to help evaluate potential fixes for the problem. Many of the methods available in structural dynamics were applied, including modal displacement and stress analysis, frequency and transient response to tip loading from the first-stage Blade Outer Gas Seals (BOGS), fourier analysis, and shock spectra analysis of the transient response. The primary findings were that the BOGS tip loading is impulsive in nature, thereby exciting many modes of the blade that exhibit high stress at the tip cracking location. Therefore, a proposed BOGS count change would not help the situation because a clearly identifiable resonance situation does not exist. The recommendations for the resolution of the problem are to maintain the existing BOGS count, eliminate the stress concentration in the blade due to its geometric design, and reduce the applied load on the blade by adding shiplaps in the BOGS.

Brown, A. M.↗
NASA NTRS1994

Composite-Plate-Buckling Analysis Program

Composite-Plate-Buckling Analysis Program (COMPPAP) helps engineers determine buckling loads of orthotropic or isotropic irregularly shaped plates without need to perform manual calculations and extensive finite-element mathematical modeling. One-element finite-element program utilizing high-order displacement functions to perform plane-stress analysis of general plate followed by buckling calculation based on stresses found in plane-stress solution. High order of displacement functions enables user to obtain results more accurately. Written in ANSI FORTRAN 77. Two machine versions available: (MSC-22428) for computers of IBM PC 386 and higher series and for compatible computers; and UNIX (MSC-22286).

Smith, James P.↗
NASA NTRS1974

On thermal stress failure of the SNAP-19A RTG heat shield

Results of a study on thermal stress problems in an amorphous graphite heat shield that is part of the launch-abort protect system for the SNAP-19A radio-isotope thermoelectric generators (RTG) that will be used on the Viking Mars Lander are presended. The first result is from a thermal stress analysis of a full-scale RTG heat source that failed to survive a suborbital entry flight test, possibly due to thermal stress failure. It was calculated that the maximum stress in the heat shield was only 50 percent of the ultimate strength of the material. To provide information on the stress failure criterion used for this calculation, some heat shield specimens were fractured under abort entry conditions in a plasma arc facility. It was found that in regions free of stress concentrations the POCO graphite heat shield material did fracture when the local stress reached the ultimate uniaxial stress of the material.

Pitts, W. C.↗