SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
DEC VAX 11/780 version of the Simplified Shuttle Payload Thermal Analyzer (SSPTA) aids in evaluating thermal design of instruments to be flown in the Space Shuttle cargo bay. SSPTA is a collection of programs that are currently used in thermal analysis of spacecraft, modified for quick, preliminary analysis of payloads.
The thermal architecture for the Surface Water Ocean Topography mission utilizes loop heat pipes and constant conductance heat pipes to transport waste heat (> 1000 Watts) from the instrument electronics to the radiator. The main thermal design risk is the ability to maintain a temporal stability of <0.05 Celsius per minute in a low earth orbit environment. The stringent thermal requirements are part of the overall error budget needed to meet the primary mission science objectives. A testbed was developed to simulate flight-like loads and environments in order to validate the thermal subsystem can meet the temporal stability requirements. Preliminary testing showed that the thermal control system can meet the stability requirement and that loop heat pipes are actually helping to maintain stability during transient sink temperature changes for this specific flight application and boundary conditions.
This paper describes a multi-scale thermal analysis approach for the design of an air-cooled 1.7-kV SiC MOSFET-based medium-voltage variable-speed motor drive. The National Renewable Energy Laboratory supported the project objectives by providing thermal management design support to the project partner The Ohio State University (OSU). The scope of the models and limited resources required efficient and flexible thermal models to be developed. Two modeling techniques are described that significantly reduced model run time and enabled more complex models to be run faster while retaining needed accuracy. The first technique uses the effectiveness-NTU method to extract convection boundary conditions from a computational fluid dynamics (CFD) model that can be applied to a fast-running finite element analysis model. The second is a porous media technique that enables system-level CFD simulations that incorporate effects from heat exchangers (e.g., pin fin heat sinks) that run in a fraction of the time required for fully resolved CFD simulations. The multi-scale approach to the thermal analysis enabled fast and accurate simulation for the converter design ranging from the die level up to the full system with 36 submodules. The modeling results were validated against experimental data from system tests performed by OSU.
This paper deals with the measurement of the total hemispherical emittance of a silicon carbide coated carbon composite which is the thermal control material of the nose cone and leading edges of the Space Shuttle. In order to effect the thermal design of the spacecraft, it is desirable to have emittance data available for the temperature range 100 K to 2000 K to encompass the thermal extremes associated with orbiting and reentry conditions. Since the multiple thermal cycling associated with fifty to one hundred missions might result in substantial property changes, the data to be presented are for the low temperature regime 100 K to 450 K for both virgin material and material which was thermally treated to simulate multiple reentries. The discussion emphasizes the identification of possible sources of error in the measurement of equilibrium temperatures and the extent to which these measurement errors or uncertainties would alter the derived emittance values.
The Space Station Electric Power System will rely on nickel-hydrogen batteries in its photovoltaic power subsystem for energy storage to support eclipse and contingency operations. These 81-Ah batteries will be designed for a 5-year life capability and are configured as orbital replaceable units (ORUs), permitting replacement of worn-out batteries over the anticipated 30-year Station life. This paper describes the baseline design and the development plans for the battery assemblies, the battery ORUs and the battery system. Key elements reviewed are the cells, mechanical and thermal design of the assembly, the ORU approach and interfaces, and the electrical design of the battery system. The anticipated operational approach is discussed, covering expected performance as well as the processor-controlled charge management and discharge load allocation techniques. Development plans cover verification of materials, cells, assemblies and ORUs, as well as system-level test and analyses.
A high efficiency, high power density, low distortion 250kW motor controller is being developed at NASA Glenn Research Center. Future electric aircraft require motor controllers which achieve the needed key performance parameters required to show benefit in increasing overall aircraft efficiency. Through a combination of carefully considered electrical topological choices and through the use of recent advancements in power switches and magnetic materials, a converter is designed which meets these requirements. A multilevel and interleaved converter architecture is chosen to meet the voltage, current, and THD requirements. The enclosure and thermal designs meet their weight targets and enable high altitude operation.
The purpose of this paper is to define a set of thermal requirements which can be used for conceptual design studies of the Subsonic Single Aft eNgine (SUSAN) aircraft and the early design phases of a 25% scale flight research aircraft. SUSAN presents an architecture for a subsonic regional jet transport aircraft coupling a single turbofan engine to an electrified aircraft propulsion system (EAP). NASA, military, FAA, and commercial standards and guidance on the design and analysis of thermal management systems for aircraft are reviewed and summarized. The approach toward using these sources to develop the SUSAN thermal requirements is described. These requirements address the definition of the thermal environment, the design requirements for certain components that interface with the thermal management system, and thermal analysis margins.
Marshall Space Flight Center is involved in a wide variety of microgravity projects that require furnaces, with hot zone temperatures ranging from 300 C to 2300 C, requirements for gradient processing and rapid quench, and both semi-conductor and metal materials. On these types of projects, the thermal engineer is a key player in the design process. Microgravity furnaces present unique challenges to the thermal designer. One challenge is designing a sample containment assembly that achieves dual containment, yet allows a high radial heat flux. Another challenge is providing a high axial gradient but a very low radial gradient. These furnaces also present unique challenges to the thermal analyst. First, there are several orders of magnitude difference in the size of the thermal 'conductors' between various parts of the model. A second challenge is providing high fidelity in the sample model, and connecting the sample with the rest of the furnace model, yet maintaining some sanity in the number of total nodes in the model. The purpose of this paper is to present an overview of the challenges involved in designing and analyzing microgravity furnaces and how some of these challenges have been overcome. The thermal analysis tools presently used to analyze microgravity furnaces and will be listed. Challenges for the future and a description of future analysis tools will be given.
This paper describes Trident, a proposed Discovery mission to Neptune’s moon Triton, 30 AU from the Sun. Triton formed in the Kuiper Belt but was captured by Neptune into a highly-inclined retrograde orbit, where tidal forces thawed its interior, forming an ocean that likely persists to the present day. Recent outer solar system missions like Cassini and New Horizons have yielded completely new models for processes on ocean worlds, active worlds, and KBOs. Triton isn’t just a key to solar system science, it’s a whole keyring: a singular captured KBO and evolved ocean world, with active plumes, an energetic ionosphere, and a young unique surface. The NASA OPAG Roadmap to Ocean Worlds identifies Triton as the highest priority candidate ocean world [1], ripe for investigation. The Trident mission concept is an excellent case study in “design to cost”: we show how exploration of Triton under Discovery is made possible by radioisotope power combined with a rare, extremely efficient Jupiter gravity assist, enabling a simple, lowmass spacecraft design on a ballistic trajectory. The Triton encounter sequence probes for an ocean, measures the ionosphere, and views nearly the whole of Triton as it traverses a single orbit around Neptune, mapping the >60% of the surface that is as yet unseen. The Triton encounter concludes with fullframe imaging illuminated by “Neptune-shine” when Trident is in Neptune eclipse, for direct comparison with Voyager 2’s observations nearly 50 years prior. Trident carries a mature complement of instruments: a Magnetometer, IR Spectrometer & Narrow Angle Camera, Wide-Angle Camera, Plasma Spectrometer, and telecom hardware-enabled Radio Science. The flight system design integrates heritage components from Ball with JPL leadership and expertise in key specialty areas to provide a Voyager-like, robust spacecraft commensurate with a Discovery cost and risk tolerance. Cost avoidance features include: use of existing instrument designs, small blowdown monopropellant propulsion system, a contributed X-band telecommunications system that also performs radio science, and a simple power system. Additionally, the passive thermal design accommodates the large solar dynamic range from Venus to Neptune by using the HGA for shade when close to the sun, and MMRTG excess heat, modulated by louvers.
The objective of this study was to produce an independent set of ascent environments which would serve as a check on the Rockwell IVBC-3 environments and provide an independent reevaluation of the thermal design criteria for the External Tank (ET). Design heating rates and loads were calculated at 367 acreage body point locations. Ascent flight regimes covered were lift-off, first stage ascent, Solid Rocket Booster (SRB) staging and second stage ascent through ET separation. The purpose here is to document these results, briefly describe the methodology used and present the environments along with a comparison with the Rockwell IVBC-3 counterpart. The methodology and environment summaries are given.
Under the expired ICRADA JSA2012S015 mod 5, JLab collaborated with HZB to design and prototype the high power HOM load for HZB VSR upgrade 1.5GHz cavities and bERLinpro cavities, as well as the optimization of the HOM waveguide thermal design. The scope of work to be contracted with this ICRADA includes: finalize the HZB VSR HOM load design for production; fabricate, test and deliver 30 HOM loads to HZB; design and prototype the HZB VSR HOM waveguide assembly.
Such state-of-the-art devices as multielement linear laser diode arrays, multichannel acoustooptic modulators, optical relays, and avalanche photodiode arrays, are presently applied to the implementation of a 32-bit supercomputer's general-purpose optical central processing architecture. Shannon's theorem, Morozov's control operator method (in conjunction with combinatorial arithmetic), and DeMorgan's law have been used to design an architecture whose 100 MHz clock renders it fully competitive with emerging planar-semiconductor technology. Attention is given to the architecture's multichannel Bragg cells, thermal design and RF crosstalk considerations, and the first and second anamorphic relay legs.
The present conference discusses such space nuclear power (SNP) issues as current design trends for SDI applications, ultrahigh heat-flux systems with curved surface subcooled nucleate boiling, design and manufacturing alternatives for low cost production of SNPs, a lightweight radioisotope heater for the Galileo mission, compatible materials for uranium fluoride-based gas core SNPs, Johnson noise thermometry for SNPs, and uranium nitride/rhenium compatibility studies for the SP-100 SNP. Also discussed are system issues in antimatter energy conversion, the thermal design of a heat source for a Brayton cycle radioisotope power system, structural and thermal analyses of an isotope heat source, a novel plant protection strategy for transient reactors, and beryllium toxicity.
In the last few years, Marshall Space Flight Center has become heavily involved in a wide variety of microgravity projects that require furnaces, with hot zone temperatures ranging from 300 C to 2300 C, requirements for isothermal and gradient processing, and both semi-conductor and metal materials. On these types of projects, the thermal engineer is a key player in the design process. These furnaces present unique challenges to the thermal designer. One challenge is designing a sample containment system that achieves dual containment, yet allows a high radial heat flux. Another challenge is providing a high axial gradient but a very low radial gradient. These furnaces also present unique challenges to the thermal analyst. First, there are several orders of magnitude difference in the size of the thermal "conductors" between various parts of the model. A second challenge is providing high fidelity in the sample model, and connecting the sample with the rest of the furnace model, yet maintaining some sanity in the number of total nodes in the model. The purpose of this paper is to present an overview of the challenges involved in designing and analyzing microgravity furnaces and how some of these challenges have been overcome. The thermal analysis tools presently used to analyze microgravity furnaces and how they have been applied will be explained. Challenges for the future and a description of future analysis tools will be given.
Spacecraft radiators are sized for their maximum heat load in their warmest thermal environment, but must operate at reduced heat loads and in colder environments. For systems where the radiator environment can be colder than the working fluid freezing temperature, radiator freezing becomes an issue. Radiator freezing has not been a major issue for the Space Shuttle and the International Space Station (ISS) active thermal control systems (ATCSs) because they operate in environments that are warm relative to the freezing point of their external coolants (Freon-21 and ammonia, respectively). For a vehicle that lands at the Lunar South Pole, the design thermal environment is 215K, but the radiator working fluid must also be kept from freezing during the 0 K sink of transit. A radiator bypass flow control design such as those used on the Space Shuttle and ISS requires more than 30% of the design heat load to avoid radiator freezing during transit - even with a very low freezing point working fluid. By changing the traditional ATCS architecture to include a regenerating heat exchanger inboard of the radiator and by using a regenerator bypass flow control valve to maintain system setpoint, the required minimum heat load can be reduced by more than half. This gives the spacecraft much more flexibility in design and operation. The present work describes the regenerator bypass ATCS setpoint control methodology. It includes analytical results comparing the performance of this system to the traditional radiator bypass system. Finally, a summary of the advantages of the regenerator bypass system are presented.
The objective of the study was to produce an independent set of ascent environments which would serve as a check on the Rockwell International (RI) IVBC-3 environments and provide an independent reevaluation of the thermal design criteria for the External Tank (ET). Given here are the plotted timewise environments comparing REMTECH results to the RI IVBC results.
In January 2004, two Mars Exploration Rovers (MER) landed on the surface of Mars to begin their mission as robotic geologists. A year prior to these historic landings, both rovers and the spacecraft that delivered them to Mars, were completing a series of environmental tests in facilities at the Jet Propulsion Laboratory. This paper describes the test program undertaken to validate the thermal design and verify the workmanship integrity of both rovers and the spacecraft. The spacecraft, which contained the rover within the aeroshell, were tested in a 7.5 m diameter thermal vacuum chamber. Thermal balance was performed for the near earth (hot case) condition and for the near Mars (cold case) condition. A solar simulator was used to provide the solar boundary condition on the solar array. IR lamps were used to simulate the solar heat load on the aeroshell for the off-sun attitudes experienced by the spacecraft during its cruise to Mars. Each rover was tested separately in a 3.0 m diameter thermal vacuum chamber over conditions simulating the warmest and coldest expected Mars diurnal temperature cycles. The environmental tests were conducted in a quiescent nitrogen atmosphere at a pressure of 8 to 10 Torr. In addition to thermal balance testing, the science instruments on board the rovers were tested successfully in the extreme environmental conditions anticipated for the mission. A solar simulator was not used in these tests.
This paper presents the thermal and mechanical design aspects of a power electronics package with 5-kV GaN devices. Through finite element analyses, we investigated the impact of different cooling configurations and device locations on the thermal performance and reliability of the package. We found that placing the devices closer to the direct bond copper substrate as opposed to a centered approach in the proposed double-sided cooling configuration resulted in improved heat dissipation. This approach also reduced the total number of attachment layers, thereby likely improving the reliability of the package. Furthermore, simulations revealed that the device location had a negligible impact on the thermomechanical behavior of the attachment layers, as they are more prone to the local coefficient of thermal expansion mismatch.