SEARCH · Search NASA

Results for “Thermal modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Comparison of Model Predictions and Performance Test Data for a Prototype Thermal Energy Storage Module

Although model predictions of thermal energy storage (TES) performance have been explored in previous investigations, relevant test data that enable experimental validation of performance models have been limited. This is particularly true for high-performance TES designs that facilitate fast input and extraction of energy. In this paper, we present a summary of experimental tests of a high-performance TES unit using lithium nitrate trihydrate phase change material as a storage medium. Performance data are presented for complete dual-mode cycles consisting of extraction (melting) followed by charging (freezing). These tests simulate the cyclic operation of a TES unit for asynchronous cooling in a variety of applications. Finally, the model analysis is found to agree reasonably well, within 10%, with the experimental data except for conditions very near the initiation of freezing, a consequence of subcooling that is required to initiate solidification.

25 ENERGY STORAGE↗

DOE OSTI2024

Analysis of radially resolved thermal conductivity in high burnup mixed oxide fuel and comparison to thermal conductivity correlations implemented in fuel performance codes

The thermal diffusivity and thermal conductivity of high burnup (19 % FIMA) mixed oxide (U, Pu)O 2 nuclear fuel has been measured along the radial direction using a thermoreflectance-based method. Measured thermal conductivity exhibits a notable radial variation consistent with the expectations that a large temperature gradient across the annular fuel pellet leads to a heterogeneous microstructure. A common fuel performance model of thermal conductivity, the Lucuta-Inoue model, is used to analyze the measured thermal conductivity profile. Further, this model adequately captures the radial dependence of thermal conductivity except in the periphery. The analysis suggests that the characteristic radial shape of the thermal conductivity profile follows the burnup profile within the fuel pin. In the periphery, the high burnup structure is formed and the conductivity model, not capturing this effect, likely overestimates the thermal conductivity.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Layer Time Control for Large Scale Additive Manufacturing Using High Performance Computing

This work proposes to optimize an additive manufacturing AM process to reduce energy and printing cost. The polymer AM process is inherently dependent on the time-temperature history of each layer to maintain geometric tolerances and mechanical integrity. Our preliminary study shows that regression-based layer time control model using thermal images could result in up to 30% build time reduction for simple geometries. This proposed work would use high-performance computing (HPC) to couple the data-driven model with thermal simulation for better predicting layer temperature profiles, improving throughput of large-scale additive manufacturing, and reducing its energy cost. We have developed a method to optimize a layer deposition time (a.k.a. layer time) for large-scale AM via physics-based simulations. A long layer time leads to an over-cooled surface on which a new layer is deposited, and therefore, it may result in a weak bonding or debonding between layers, cracking, or warping. A short layer time leads to a high temperature of the structure due to insufficient cooling, and therefore, the structure may not be stiff enough and may collapse during manufacturing. Therefore, it is important to estimate the optimal layer time in additive manufacturing for a high-quality product. The temperature of a top layer right before deposition is recommended to be slightly higher than the glass temperature of the material. A temperature cooling was approximated to an exponential function of time, and the optimized layer time was obtained based on a target temperature while maintaining a minimal printing time. The material used is carbon fiber-reinforced polycarbonate (CF/PC), and the large-scale deposition system used is LSAM TM from Thermwood Corporation. Three different layer time cases were used for experiments, and a series of thermal images were obtained via an infra-red (IR) camera during the entire AM processes. AM process simulations were performed using a finite element method and the temperature profiles from the simulation were in good agreements with those from experiments. The layer time optimization was performed based on the temperature profiles from the simulations. A layer temperature with the optimal layer time was confirmed as the target temperature through simulation. In addition to the development of a layer time optimization method, we have developed a numerical framework for AM simulation with element activations in sync with toolpath, based on an open source finite element framework, DEAL.II. A major portion of this work was presented at SAMPE 2022 Conference and Exhibition on May 2022, and published in Proceedings of SAMPE 2022.

42 ENGINEERING↗

DOE OSTI2026

Numerical Modeling & Size Optimization of Thermal Energy Storage for Iron & Steel Production

Iron and steel production are responsible for 90 million MtCO2 per year in the United States. Hydrogen direct reduction of iron (H2DRI) is a promising pathway for a more sustainable iron production than commercially deployed technologies which rely on natural gas. The H2DRI process requires hydrogen at a temperature of up to 950 degrees C fed into a reduction furnace to produce pellets or briquettes that are used in the downstream iron and steelmaking process. In this work, we propose to use an electrical thermal energy storage (ETES) system, that can use renewable electricity to store high-temperature heat and dispatch it upon demand. Such a system can buffer the H2DRI plant from the variability of electricity prices by charging during curtailment and running the plant from storage during times of peak electricity price. We have developed heat transfer models for two different ETES systems that can be used to heat up hydrogen to the required temperatures: a particle-based ETES and a firebrick ETES. These models are used to evaluate the performance of such a system and support the sizing and preliminary cost estimation. The preliminary results using both models show that designing ETES systems for an industrial-scale H2DRI furnace is feasible. The firebrick ETES system has limited operational duration, which might limit the price buffering effect unless significantly oversized. The particle ETES system heat exchanger has industry-feasible dimensions, but its storage capacity would be decided upon the number of particle storage silos.

25 ENERGY STORAGE↗

DOE OSTI2023

Model-based quantification of margins and uncertainties in metal additive manufacturing for process design and qualification

Laser powder bed fusion (LPBF) Additive Manufacturing (AM) has the potential to enable the production of components with novel designs and material properties unachievable otherwise. However, process repeatability is a challenge, making qualification ill-defined and greatly reducing the utility of what could be an important manufacturing technology. In this work, a combination of modeling, uncertainty quantification (UQ), and experimentation are used in an effort to predict and bound the range of possible outcomes of the LPBF process. Quantities of interest predicted are melt pool dimensions, microstructure features, and mechanical distortions. A combination of high fidelity thermal-fluid models, microstructure growth models, and reduced fidelity, rapid thermal and mechanical models are used. Uncertainty propagation techniques are used to predict probability distributions of quantities of interest from estimates of process uncertainties. Repeated experiments are done to quantify observed probability distributions and compared to predicted distributions to determine if predictions are precise and accurate. Novel modeling methods are microstrucutre characterization techniques are also discussed. It is found that high fidelity models do a generally good job bounding experimentally observed melt pool morphologies for both bead-on-plate and powder bed cases. Microstructure models are able to bound a number of experimentally observed microstructure statistics, but with low precision due to challenges with calibrating the microstructure growth model parameters. A developed modified inherent strain distortion model does not accurately predict observed distortions. A lumped laser distortion model shows promise in being both accurately and precisely bounding observed outcomes from the deflection comb build, but requires further evaluation on more builds and geometries.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Operational Parameter Database for Molten Salt Thermal Energy Storage Tank Modeling

The second generation of concentrated solar power (CSP) plants is characterized by the use of a central receiver (either cavity or external), two molten nitrate salt tanks (60 wt.% NaNO 3 and 40 wt.% KNO 3 ), and a steam Rankine power-generation cycle connected through a primary heat exchanger. Molten salt thermal energy storage (TES) tanks have been widely deployed in commercial CSP plants worldwide and have been essential for increasing plant dispatchability and capacity factor, while also reducing the levelized cost of electricity (LCOE). These systems enable energy storage at the gigawatt-hour scale, typically providing 6 to 17 hours of storage duration. Despite being a commercial technology, the multiple failures observed after only a few months or years of operation in plants around the world demonstrate the technology's relative infancy and highlight the need for further research to improve its reliability. The National Laboratory of the Rockies (NLR), in collaboration with industry partners and academic and research institutions, has been leading multiple projects funded by the U.S. Department of Energy (DOE). These projects focus on addressing molten salt tank failures by improving tank design and welding fabrication practices, evaluating new alloys and weld fillers, and providing guidelines for tank commissioning and safe operation. In particular, this report presents modeling results on the effect of key tank operation parameters during 60 minutes of operation, including the mass flow rate and temperature of the salt inflow, tank salt inventory temperature, and inventory level for a representative molten salt tank design. These results form a database of tank operation behaviors that captures the effects of each specific parameter during charging, charging/discharging, and discharging processes.

14 SOLAR ENERGY↗

DOE OSTI2020

BISON Capabilities for LWR Fuel Behavior Analysis During Accident and High-burnup Conditions

The U.S. Department of Energy (DOE)'s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities using computational methods for the analysis and design of advanced reactor and fuel cycle systems. This program has been supporting the development of BISON which is a high-fidelity and high-resolution fuel performance tool at the engineering scale. Increasing recent interest in applications at extended burnups motivated this study to incorporate more physically based models in BISON. This document details integration of newly implemented modeling capabilities into BISON, which includes (1) new thermal conductivity models that are valid up to 100 GWd/t, (2) models for the formation of the high-burnup structure (HBS), (3) two porosity correction methods beingapplied on the thermal conductivity due to the conducting pores during the HBS formation. BISON's results are verified and validated to test the new modeling capabilities

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Impact of fusion reactor neutronics modeling for transmutation and thermal feedback *

Abstract Fusion neutronics calculations provide important metrics pertinent to fusion device operations, such as tritium breeding ratios (TBRs) and data on heat deposition, material activation, and damage. Because of the high computational burden required to generate a high-fidelity Monte Carlo simulation of a 3D fusion device, various assumptions are made to reduce computational time by simplifying the reactor model or the calculation iteration. This paper explores the impact of fusion neutronics metrics such as the TBR and decay heat of structural materials based on assumptions of material composition in the fusion reactor and temperature modeling of materials. Results show that for compact tokamaks with high power and long operational cycles, the transmutation of structural materials is significant enough to cause a substantial change in the flux spectrum and decrease the TBR by 1.68% after 2 years of full power operation. Additionally, assuming a constant temperature and material density can impact the TBR calculations up to 3%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Machine Learning-Assisted High-Temperature Reservoir Thermal Energy Storage Optimization: Numerical Modeling and Machine Learning Input and Output Files

This data set includes the numerical modeling input files and output files used to synthesize data, and the reduced-order machine learning models trained from the synthesized data for reservoir thermal energy storage site identification. In this study, a machine-learning-assisted computational framework is presented to identify High-Temperature Reservoir Thermal Energy Storage (HT-RTES) site with optimal performance metrics by combining physics-based simulation with stochastic hydrogeologic formation and thermal energy storage operation parameters, artificial neural network regression of the simulation data, and genetic algorithm-enabled multi-objective optimization. A doublet well configuration with a layered (aquitard-aquifer-aquitard) generic reservoir is simulated for cases of continuous operation and seasonal-cycle operation scenarios. Neural network-based surrogate models are developed for the two scenarios and applied to generate the Pareto fronts of the HT-RTES performance for four potential HT-RTES sites. The developed Pareto optimal solutions indicate the performance of HT-RTES is operation-scenario (i.e., fluid cycle) and reservoir-site dependent, and the performance metrics have competing effects for a given site and a given fluid cycle. The developed neural network models can be applied to identify suitable sites for HT-RTES, and the proposed framework sheds light on the design of resilient HT-RTES systems. All the simulations and the neural network model were done by Idaho National Laboratory. A detailed description of the work was reported in publication linked below.

15 GEOTHERMAL ENERGY↗

DOE OSTI2020

Analysis of the time-of-flight neutron scattering cross-section data for light water measured at the SEQUOIA spectrometer, Spallation Neutron Source (SNS)

Thermal neutron scattering cross-section data for light water available in the major nuclear data libraries observes significant differences especially at reactor operating temperatures. During the past few years there has been a renewed interest in reviewing the existing thermal scattering models and generating more accurate and reliable thermal scattering cross sections using existing experimental data and in some cases based on Molecular Dynamics (MD) simulations. There is a need for performing new time-of-flight experiments at high temperatures and pressures, to have a better understanding of the physics involved in the scattering process that could help improve the existing TSL data.Lack of experimental thermal scattering data for light water at high temperatures led to a new measurement campaign within the INSIDER project at the Institut de radioprotection et de sûreté nucléaire (IRSN). Double differential scattering cross section for light water have been measured at the SEQUOIA spectrometer based at the Spallation Neutron Source (SNS), Oak Ridge National Laboratory, United States. Several measurements have been carried out at different temperatures and pressures corresponding to liquid light water. Measurements at five different incident neutron energies Ei (8, 60, 160, 280 and 800 meV) have been carried out to help exploring different regions of the frequency spectrum. This paper presents the analysis of the dynamic structure factor and the derived frequency spectrum of light water. The analysis of the experimental data would provide one with better confidence, the behavior of thermal scattering cross sections for light water at high temperatures, knowledge of which is very important for the design of novel reactors as well as existing pressurized water reactors.

Jaiswal, V↗

DOE OSTI2023

Concept Descriptions for the VTR Rabbit System and Driver Fuel Test Assemblies

Two of the experiment vehicles being developed for the Versatile Test Reactor (VTR) are presented here. The first is a rabbit system that will enable rapid insertion of small test capsules into the high fast flux of the VTR core for relatively short durations. The rabbit concept development includes the construction/demonstration of a near-full-scale system in a deep-water pool to demonstrate functionality, development of a concept of operations and initial procedures, and validation of thermal-hydraulic modeling. In addition, modeling efforts are underway to simulate the thermal and neutronic environment of a rabbit capsule. The second type of experiment vehicle presented here is a driver fuel test assembly for inserting fuel and materials tests into the core by replacing a driver fuel assembly. Here, a novel design for dismountable test assemblies is proposed for the VTR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Development of Microreactor Automated Control System (MACS): Surrogate Plant-level Modeling and Control Algorithms Integration

This report discusses progress on the modeling and integration task as part of the development of Microreactor Automated Control System (MACS). What follows is a discussion of the software tools used to develop a surrogate microreactor plant-level model, MACS module development, and a summary of the findings from integration with a hardware-in-the-loop (HIL) setup at Idaho National Laboratory (INL). Oak Ridge National Laboratory worked with INL to understand available hardware at INL (such as existing control platforms). With this information and using a preliminary framework for MACS with software interfaces defined, surrogate models and initial automated control algorithms were created for integration into the hardware to provide a HIL demonstration platform for MACS. Available reduced order reactor models that leverage existing microreactor neutronics and thermal hydraulics models have been integrated in the surrogate plant-level model. The surrogate model has been evaluated for sensitivity of all parameters and the MACS software modules (including the surrogate model) have been demonstrated to interact with the hardware. The integration, however, pointed to the need for further improvements to the framework—and specifically improvements to the interfaces to ensure that the HIL simulator is capable of longer-term stable operation with MACS in the loop. These improvements will be the focus of future research.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Serpent - Bison - THM Preliminary Multiphysics Modeling of a Nuclear Thermal Propulsion System Fuel Assembly

This work demonstrates the Monte Carlo neutronic and Thermo-Hydraulic coupling scheme using the Serpent code and MOOSE application Bison and Thermo Hydraulic Module. The coupling scheme is then applied to the reference BWX Technologies Nuclear Ther- mal Propulsion system at he fuel assembly level where it’s used to perform an analysis of the isothermal material coefficients and potential material reactivity worth. A method is developed to isolate which feedback effects should be considered for proceeding with reduced order deterministic neutronic modeling where branch off analysis must be con- ducted. The convergence behavior of the coupling scheme is demonstrated where it fol- lows the standard Picard iteration approach. Verification studies for the method of deduc- ing relevant feedback effects is also demonstrated.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Modeling Validation of Mechanical and Thermal Borehole Breakouts From Polyaxial Laboratory Tests to Determine Maximum Horizontal in Situ Stress

To accurately assess rock behavior in the deep subsurface, it is necessary to measure the in situ stress directions and magnitudes. The current methods for measuring the in situ stress state in the deep subsurface primarily include hydraulic fracturing tests (i.e., the minimum horizontal stress) or occasionally observing existing compressive borehole breakouts (i.e., the maximum horizontal stress) that have occurred naturally from drilling. If there are no existing compressive breakouts in a borehole, the maximum horizontal in situ stress cannot be estimated with much confidence. In response to this data gap, a new thermal breakout technology is being developed that will provide a method for thermally inducing borehole breakouts and obtaining consistent measurements of the maximum horizontal stress magnitude. This thermal breakout technology involves heating the borehole and increasing the thermoelastic compressive stress in the rock until a breakout develops, which is directly correlated to the maximum horizontal stress magnitude. In support of developing the thermal breakout technology, polyaxial laboratory tests have been performed on small-scale boreholes within rock blocks where mechanically- and thermally-induced borehole breakouts have been created. Numerical models along with the principal of superposition were created and used to analyze the polyaxial laboratory tests to predict the maximum horizontal stress, given the same data that would be obtained in an actual subsurface borehole thermal breakout test. Multiple failure criteria were used to evaluate the best prediction of the breakout onset and maximum horizontal stress. The maximum horizontal stress predictions were compared to the actual maximum horizontal stress applied at breakout using acoustic events recorded from emission sensors in the polyaxial tests. The results showed consistent results that could be used to refine the modeling approach and failure criterion that are used to make the maximum horizontal stress predictions. This study provided insight and validation for the thermal breakout stress measurement concept.

Jones, Matt↗

DOE OSTI2025

An Investigation of Thermal Properties of 2D Materials [Dissertation]

Studying the thermal conductivity of 2D materials is important due to the applications of 2D materials in fields such as thermal management, thermoelectricity, renewable energy, and sensors. As such, measurements of the thermal conductivity of these 2D materials become important to measure. Thermal conductivity is often difficult to measure for 2D materials due to their atomically thin nature and many experimental methods for doing so requiring contact with the sample, which can alter the thermal properties. A non-contact method for calculating the thermal conductivity of 2D materials supported on substrates in order to model the thermal conductivity of 2D materials for devices, is proposed and experimentally performed in this dissertation. The optothermal Raman technique is a useful non-contact diagnostic technique useful in determining the thermal conductivity of 2D materials. The optothermal Raman typically does not account for heat losses due to convection or radiation or substrate resistance, which are shown to be important factors to consider when developing an optothermal Raman model. Additionally, the calculation of the interfacial thermal conductance between the bottom surface of the sample and the top surface of the substrate, plays an important role in determining the final value of the thermal conductivity of a supported sample, and will yield differing results based on whether or not the conductance is calculated using an approach such as the Diffuse Mismatch Model (DMM) or calculated directly by varying the laser heating profile (usually done by changing the laser objective). This is shown to be the case for both graphene on Ni, graphene on Cu, and SnSe 2 on Cu. In addition to experimentally calculating the thermal conductivity of a 2D material with the optothermal Raman technique, the thermal conductivity of 2D materials can also be calculated using computational methods. The three-phonon method is a method which can be used to simulate phonon scattering processes and determine the thermal conductivity of semiconductors, wherein phonon scattering is the dominant mechanism which determines the thermal conductivity. The three-phonon method uses relaxation times for phonon scattering with other phonons, electrons, and other material system elements, such as isotopes or material defects, in order to create a single-mode relaxation time approximation (SMRTA), which is used to calculate the final value of the thermal conductivity. An important consideration when determining the thermal conductivity of a 2D material using this method is the device geometry, which is reflected in this work as the phonon-boundary scattering relaxation time. This inclusion is important along with the inclusion of phonon-electron scattering in accurately determining the thermal conductivity of a 2D material. In both the optothermal Raman experiments and the three-phonon method computations, strain is shown to have a demonstrable effect on the thermal conductivity of 2D materials. When a 1.1% strain was applied to the mechanical properties of SnSe, the three-phonon processes yielded a lower thermal conductivity than the no-strain case. For the optothermal Raman experiments, the strain induced in the Cu substrate and transferred to a single-layer graphene (SLG) sample yields a trend where the thermal conductivity of the SLG decreases with respect to strain applied. In the case where the interfacial thermal conductance was calculated directly, the conductance increased with respect to strain applied. This presents strain as a reliable and viable method for tuning the thermal properties of 2D materials for device applications.

36 MATERIALS SCIENCE↗

DOE OSTI2026

ThermoPI—an Online Tool to Calculate Heat Transfer Through Foam Insulation

Thermal insulation materials with ultra-low effective thermal conductivity are crucial for a multitude of applications. Over the years, a significant amount of experimental work has been dedicated to creating new insulation materials with low thermal conductivity. Similarly, substantial efforts have been made to enhance the theoretical understanding of thermal transport mechanisms in thermal insulation materials and to push the boundaries of lower thermal conductivity. However, ample room remains for enhancing the thermal resistivity of closed-cell foam insulations. To aid in the development of ultra-low effective thermal conductivity foam insulations, Oak Ridge National Laboratory has introduced a unique online tool, ThermoPI. This tool calculates not only the effective thermal conductivity but also the thermal conductivity components for porous materials, including gases, solids, and radiative, based on the materials’ structural information (e.g., porosity, pore size, gas species, pressure, solid species, pore geometry, and temperature).This tool collected and improved the existing theoretical models for thermal insulation materials’ gas, solid, and radiative thermal conductivity. These improved models have been validated with experimental data. Effective medium theory and sound velocity softening effects are considered for solid thermal conductivity. The built-in solid materials include polystyrene, polyurethane, polyethylene, and silica. Users are allowed to input new solid materials that are not built inside the tool. For gas thermal conductivity, the subcontinuum Knudsen effect is considered. In addition to several built-in gases, users can input new gases. For solid and radiative thermal conductivity calculations, several models are available to select, and the tool can determine the best model to choose based on the materials that users input. Users are also allowed to change selections manually. In addition, the tool can also calculate the effect of interfacial resistance on the overall thermal conductivity of layered materials. This work will elaborate on the tool and discuss how it can guide the development of new insulation products.

Shrestha, Som [ORNL] (ORCID:0000000183993797)↗

DOE OSTI2024

Site‐selective fluorescence and spectroscopic properties of Yb‐doped lanthanum titanate glasses

Abstract Ytterbium‐doped lanthanum titanate glasses were prepared by levitation melting for the detailed characterization of the spectroscopic properties in the rare‐earth titanate glass host. Low‐temperature fluorescence spectroscopy reveals distinct site‐selectivity in both static and lifetime fluorescence measurements suggesting an absence of clustering as well as significant variation of local ytterbium environments. Typical site‐selectivity behavior of a shrinking Stark manifold with lower excitation energy is observed. At 77 K, both the mean emission frequency and the fluorescence lifetime initially increase as the excitation energy decreases from about 11100 to 10750 and then slightly decrease at lower excitation energy. Temperature‐dependent lifetime measurements between 77 and 420 K show a decreasing lifetime with increasing temperature and are well described by a two‐level thermal activation model. The temperature‐dependent fluorescence spectroscopy coupled with a room temperature white light absorption measurement allow the determination of the Stark energy levels of in lanthanum titanate glass as well as the calculation of the laser cross‐sections.

Materials Science↗

DOE OSTI2021

Effect of thermal environments on fast charging Li-ion batteries

Battery thermal management systems (BTMSs) are expected to keep the battery temperature at a moderate level (~30 °C) to minimize the thermally exacerbated degradation. However, during fast charging, a strong cooling system is required to restrict the temperature rise of Li-ion batteries (LiBs), which significantly increases the cost and weight of battery packs, and induces a large temperature variation inside the battery. Here, in this work, we find that all these drawbacks could be relieved by allowing LiBs to charge at higher temperatures. Since the fast charging of a LiB only takes a tiny fraction of its lifetime, the aging rate is limited even at a charging temperature of 60 °C. Three types of thermal environments are proposed: kept constant at 30 °C, preheated to 60 °C, and adiabatic fast charging. With an experimentally validated electrochemical-thermal (ECT) coupled model, we explore the interplay between thermal management and the fast-charging performance. It is found that a gradually increasing temperature profile is the best option to balance the lithium plating and thermal management of the battery. Combining adiabatic fast charging with a preheating step, we can achieve minimal cooling need, perfect temperature uniformity within a battery, and fast-charging capability simultaneously.

25 ENERGY STORAGE↗