Search NASA⌕ Search

SEARCH · Search NASA

Results for “Turbulence experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Control of forebody three-dimensional flow separations

Some experiments involving the development of the turbulent symmetric vortex flow about the lee side of a 5 deg semiangle conical forebody at high relative incidence are discussed. The cone was immersed in a Mach 0.6 airstream at a Reynolds number of 13.5 million based on the 1.4 - m axial length of the cone. Novel means of controlling the degree of asymmetry using blowing very close to the nose were investigated. Small amounts of air injected normally or tangentially to the cone surface, but on one side of the leeward meridian and beneath the vortex farthest from the wall, were effective in biasing the asymmetry. With this reorientation of the forebody vortices, the amplitude of the side force could be reduced to the point where its direction was reversed. This phenomenon could be obtained either by changing the blowing rate at constant incidence or by changing incidence at constant blowing rate. Normal injection was more effective than tangential injection. An organized and stable flow structure emerged with the jet vortices positioned above the forebody vortices.

Peake, D. J.↗
NASA NTRS1980

Simple turbulence models and their application to boundary layer separation

Measurements in the boundary layer and wake of a stalled airfoil are presented in two coordinate systems, one aligned with the airfoil chord, the other being conventional boundary layer coordinates. The NACA 4412 airfoil is studied at a single angle of attack corresponding to maximum lift, the Reynolds number based on chord being 1.5 x 10 to the 6th power. Turbulent boundary layer separation occurred at the 85 percent chord position. The two-dimensionality of the flow was documented and the momentum integral equation studied to illustrate the importance of turbulence contributions as separation is approached. The assumptions of simple eddy-viscosity and mixing-length turbulence models are checked directly against experiment. Curvature effects are found to be important as separation is approached.

Wadcock, A. J.↗
NASA NTRS1982

Flow process in combustors

Fluid mechanical effects on combustion processes in steady flow combustors, especially gas turbine combustors were investigated. Flow features of most interest were vorticity, especially swirl, and turbulence. Theoretical analyses, numerical calculations, and experiments were performed. The theoretical and numerical work focused on noncombusting flows, while the experimental work consisted of both reacting and nonreacting flow studies. An experimental data set, e.g., velocity, temperature and composition, was developed for a swirl flow combustor for use by combustion modelers for development and validation work.

Gouldin, F. C.↗
NASA NTRS1983

Theory of hydromagnetic turbulence

The present state of MHD turbulence theory as a possible solar wind research tool is surveyed. The theory is statistical, and does not make statements about individual events. The ensembles considered typically have individual realizations which differ qualitatively, unlike equilibrium statistical mechanics. Most of the theory deals with highly symmetric situations; most of these symmetries have yet to be tested in the solar wind. The applicability of MHD itself to solar wind parameters is highly questionable; yet it has no competitors, as a potentially comprehensive dynamical description. The purpose of solar wind research require sharper articulation. If they are to understand radial turbulent plasma flows from spheres, laboratory experiments and numerical solution of equations of motion may be cheap alternative to spacecraft. If "real life" information is demanded, multiple spacecraft with variable separation may be necessary to go further. The principal emphasis in the theory so far has been on spectral behavior for spatial covariances in wave number space. There is no respectable theory of these for highly anisotropic situations. A rather slow development of theory acts as a brake on justifiable measurement, at this point.

Montgomery, D.↗
NASA NTRS1984

Convergent-tapered annular seals - Analysis and testing for rotordynamic coefficients

A combined analytical-computational method has been developed to calculate the pressure field and dynamic coefficients for tapered high-pressure annular seals. Completely developed turbulent flow is assumed in both the circumferential and axial directions, according to Hirs' (1973) bulk-flow turbulent-lubrication equations. In a numerical experiment with the method, a short bearing approximation is used to derive an analytical expression for the first-order (dynamic) pressure gradient. This expression is integrated numerically to define dynamic coefficients of the seal. Numerical results of the integration are compared with previous results for straight and tapered seals. It is found that direct stiffness and leakage coefficients increase in the present seal, while the remaining coefficients decrease. An optimal taper angle is shown to exist with respect to: (1) the direct stiffness and (2) the ratio of direct stiffness to leakage. On the basis of the optimal taper angle calculations, stiffness increases on the order of 40 to 50 percent are predicted. Experimental results for three taper angles are presented, and are found to be in good agreement with the theoretical predictions.

Childs, D. W.↗
NASA NTRS1987

Flowfield characteristics of an axisymmetric 180-degree turnaround duct

In an attempt to provide an experimental database for computational fluid dynamics turbulence code evaluation and development, an experiment was conducted using an annular axisymmetric 180-deg turnaround passage through which air flows at close to ambient conditions. Measurements made at a nominal gap Reynolds number of 100,000 are presented; these are the static and fluctuating wall pressure distributions and the one- and two-component velocity profiles at various stations upstream, through, and downstream of the bend. Because of the large favorable pressure gradients on the inner wall up to 51 degrees, the flow experiences a large acceleration close to the wall; enhanced mixing occurs close to the outer wall. Downstream of this location, the flow close to the inner wall experiences an adverse pressure gradient before separating at about 150 degrees.

Ostermier, B. J.↗
NASA NTRS1989

Aircraft modal supression system: Existing design approach and its shortcomings

The bending of flexible body aircraft may degrade the ride coMfort of passengers. This is especially noticeable towards the aft end of the aircraft (due to the relatively large tail surfaces) which may easily be excited when flying through turbulence. In addition, some aircraft may experience a front body bending mode which can be annoying to the cabin crew and first class passengers. Normally, this dominant body bending mode falls between 1 to 5 Hz. This range is easily perceived by the human body. Also, in some situations, the rigid body control law may be out of phase with the mode and aggravate the vibration. Hence, an active modal suppression system is desirable for improving the ride quality of the airplane. The size of the mathematical model, which has both the airplane rigid body and flexible characteristics, could easily exceed 100 states. The computational burden and fidelity of this large structural model is addressed.

Ho, J. K.↗
NASA NTRS1989

Laboratory and theoretical models of planetary-scale instabilities and waves

The continuous low-g environment of the orbiting space shuttle provided a setting for conducting geophysical fluid model experiments with a completely consistent representation of sphericity and the resultant radial gravity found on astrogeophysical objects. This is possible because in zero gravity an experiment can be constructed that has its own radial buoyancy forces. The dielectric forces in a liquid, which are linearly dependent on fluid temperature, give rise to an effectively radial buoyancy force when a radial electrostatic field is applied. The Geophysical Fluid Flow Cell (GFFC) experiment is an implementation of this idea in which fluid is contained between two rotating hemispheres that are differentially heated and stressed with a large ac voltage. The GFFC flew on Spacelab 3 in May 1985. Data in the form of global Schlieren images of convective patterns were obtained for a large variety of configurations. These included situations of rapid rotation (large Taylor numbers), low rotation, large and small thermal forcing, and situations with applied meridional temperature gradients. The analysis and interpretation of the GFFC-85 data are being conducted. Improvements were developed to the GFFC instrument that will allow for real-time (TV) display of convection data and for near-real-time interactive experiments. These experiments, on the transition to global turbulence, the breakdown of rapidly rotating convective planforms and other phenomena, are scheduled to be carried out on the International Microgravity Laboratory (IML-1) aboard the shuttle in June 1990.

Hart, John E.↗
NASA NTRS1990

Numerical simulations of soft and hard turbulence - Preliminary results for two-dimensional convection

Results on the transition from soft to hard turbulence in simulations of two-dimensional Boussinesq convection are reported. The computed probability densities for temperature fluctuations are exponential in form in both soft and hard turbulence, unlike what is observed in experiments. In contrast, a change is obtained in the Nusselt number scaling on Rayleigh number in good agreement with the three-dimensional experiments.

Deluca, E. E.↗
NASA NTRS1991

Evaluation of a technique to generate artificially thickened boundary layers in supersonic and hypersonic flows

The feasibility of using a contoured honeycomb model to generate a thick boundary layer in high-speed, compressible flow was investigated. The contour of the honeycomb was tailored to selectively remove momentum in a minimum of streamwise distance to create an artificially thickened turbulent boundary layer. Three wind tunnel experiments were conducted to verify the concept. Results indicate that this technique is a viable concept, especially for high-speed inlet testing applications. In addition, the compactness of the honeycomb boundary layer simulator allows relatively easy integration into existing wind tunnel model hardware.

Porro, A. R.↗
NASA NTRS1991

Numerical prediction of turbulent oscillating flow and associated heat transfer

A crucial point for further development of engines is the optimization of its heat exchangers which operate under oscillatory flow conditions. It has been found that the most important thermodynamic uncertainties in the Stirling engine designs for space power are in the heat transfer between gas and metal in all engine components and in the pressure drop across the heat exchanger components. So far, performance codes cannot predict the power output of a Stirling engine reasonably enough if used for a wide variety of engines. Thus, there is a strong need for better performance codes. However, a performance code is not concerned with the details of the flow. This information must be provided externally. While analytical relationships exist for laminar oscillating flow, there has been hardly any information about transitional and turbulent oscillating flow, which could be introduced into the performance codes. In 1986, a survey by Seume and Simon revealed that most Stirling engine heat exchangers operate in the transitional and turbulent regime. Consequently, research has since focused on the unresolved issue of transitional and turbulent oscillating flow and heat transfer. Since 1988, the University of Minnesota oscillating flow facility has obtained experimental data about transitional and turbulent oscillating flow. However, since the experiments in this field are extremely difficult, lengthy, and expensive, it is advantageous to numerically simulate the flow and heat transfer accurately from first principles. Work done at the University of Minnesota on the development of such a numerical simulation is summarized.

Koehler, W. J.↗
NASA NTRS1994

Numerical Simulation of Supersonic Compression Corners and Hypersonic Inlet Flows Using the RPLUS2D Code

A two-dimensional computational code, PRLUS2D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for two-dimensional shock-wave/turbulent-boundary-layer interactions. The problem of compression corners at supersonic speeds was solved using the RPLUS2D code. To validate the RPLUS2D code for hypersonic speeds, it was applied to a realistic hypersonic inlet geometry. Both the Baldwin-Lomax and the Chien two-equation turbulence models were used. Computational results showed that the RPLUS2D code compared very well with experimentally obtained data for supersonic compression corner flows, except in the case of large separated flows resulting from the interactions between the shock wave and turbulent boundary layer. The computational results compared well with the experiment results in a hypersonic NASA P8 inlet case, with the Chien two-equation turbulence model performing better than the Baldwin-Lomax model.

Kapoor, Kamlesh↗
NASA NTRS1994

Drag reduction strategies

previously a description was given of an active control scheme using wall transpiration that leads to a 15% reduction in surface skin friction beneath a turbulent boundary layer, according to direct numerical simulation. In this research brief further details of that scheme and its variants are given together with some suggestions as to how sensor/actuator arrays could be configured to reduce surface drag. The research which is summarized here was performed during the first half of 1994. This research is motivated by the need to understand better how the dynamics of near-wall turbulent flow can be modified so that skin friction is reduced. The reduction of turbulent skin friction is highly desirable in many engineering applications. Experiments and direct numerical simulations have led to an increased understanding of the cycle of turbulence production and transport in the boundary layer and raised awareness of the possibility of disrupting the process with a subsequent reduction in turbulent skin friction. The implementation of active feedback control in a computational setting is a viable approach for the investigation of the modifications to the flow physics that can be achieved. Bewley et al. and Hill describe how ideas from optimal control theory are employed to give 'sub-optimal' drag reduction schemes. The objectives of the work reported here is to investigate in greater detail the assumptions implicit within such schemes and their limitations. It is also our objective to describe how an array of sensors and actuators could be arranged and interconnected to form a 'smart' surface which has low skin friction.

Hill, D. Christopher↗
NASA NTRS1998

Effect of Apex Flap Deflection on Vertical Tail Buffeting

A computational study of the effect of vortex breakdown location on vertical tail buffeting is conducted. The position of the breakdown is modified by employing an apex flap deflected by an experimentally determined optimal angle. The delayed breakdown flow and buffeting response is then compared to the nominal undeflected case. This multidisciplinary problem is solved sequentially for the fluid flow, the elastic tail deformations and the grid displacements. The fluid flow is simulated by time accurately solving the unsteady, compressible, Reynolds-averaged Navier-Stokes equations using an implicit, upwind, flux-difference splitting finite volume scheme. The elastic vibrations of the tails are modeled by uncoupled bending and torsion beam equations. These equations are solved accurately in time using the Galerkin method and a five-stage Runge-Kutta-Verner scheme. The grid for the fluid dynamics calculations is continuously deformed using interpolation functions to disperse the displacements smoothly throughout the computational domain. An angle-of-attack of 35 deg.is chosen such that the wing primary-vortex cores experience vortex breakdown and the resulting turbulent wake flow impinges on tile vertical tails. The dimensions and material properties of the vertical tails are chosen such that the deflections are large enough to insure interaction with the flow, and the natural frequencies are high enough to facilitate a practical computational solution. Results are presented for a baseline uncontrolled buffeting case and a delayed breakdown case in which the apex flap has been deflected 15 deg. The flap was found to be very effective in delaying the breakdown, increasing the location from 50%c to 94%c, which resulted in a 6% increase in lift coefficient and pitching moment. However, the integrated buffet loads and tip responses were roughly equivalent for the two cases.

Massey, Steven J.↗
NASA NTRS2001

Preliminary Study of Electron Emission for Use in the PIC Portion of MAFIA

This memorandum summarizes a study undertaken to apply the program MAFIA to the modeling of an electron gun in a traveling wave tube (TWT). The basic problem is to emit particles from the cathode in the proper manner. The electrons are emitted with the classical Maxwell-Boltzmann (M-B) energy distribution; and for a small patch of emitting surface; the distribution with angle obeys Lambert's law. This states that the current density drops off as the cosine of the angle from the normal. The motivation for the work is to extend the analysis beyond that which has been done using older codes. Some existing programs use the Child-Langmuir, or 3/2 power law, for the description of the gun. This means the current varies as the 3/2 power of the anode voltage. The proportionality constant is termed the perveance of the gun. This is limited, however, since the 3/2 variation is only an approximation. Also, if the cathode is near saturation, the 3/2 law definitely will not hold. In most of the older codes, the electron beam is decomposed into current tubes, which imply laminar flow in the beam; even though experiments show the flow to be turbulent. Also, the proper inclusion of noise in the beam is not possible. These older methods of calculation do, however, give reasonable values for parameters of the electron beam and the overall gun, and these values will be used as the starting point for a more precise particle-in-cell (PIC) calculation. To minimize the time needed for a given computer run, all beams will use the same number of particles in a simulation. This is accomplished by varying the mass and charge of the emitted particles (macroparticles) in a certain manner, to be consistent with the desired beam current.

Freeman, Jon C.↗
NASA NTRS2001

NASA National Combustion Code Simulations

A systematic effort is in progress to further validate the National Combustion Code (NCC) that has been developed at NASA Glenn Research Center (GRC) for comprehensive modeling and simulation of aerospace combustion systems. The validation efforts include numerical simulation of the gas-phase combustor experiments conducted at the Center for Turbulence Research (CTR), Stanford University, followed by comparison and evaluation of the computed results with the experimental data. Presently, at GRC, a numerical model of the experimental gaseous combustor is built to simulate the experimental model. The constructed numerical geometry includes the flow development sections for air annulus and fuel pipe, 24 channel air and fuel swirlers, hub, combustor, and tail pipe. Furthermore, a three-dimensional multi-block, multi-grid grid (1.6 million grid points, 3-levels of multi-grid) is generated. Computational simulation of the gaseous combustor flow field operating on methane fuel has started. The computational domain includes the whole flow regime starting from the fuel pipe and the air annulus, through the 12 air and 12 fuel channels, in the combustion region and through the tail pipe.

Iannetti, Anthony↗
NASA NTRSDate not supplied

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

High-Order Methods↗
NASA NTRSDate not supplied

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

Direct Numerical Simulations↗