Results for “Two dimensional flow” — Page 29

NASA NTRS1996

An Evaluation of the Measurement Requirements for an In-Situ Wake Vortex Detection System

Results of a numerical simulation are presented to determine the feasibility of estimating the location and strength of a wake vortex from imperfect in-situ measurements. These estimates could be used to provide information to a pilot on how to avoid a hazardous wake vortex encounter. An iterative algorithm based on the method of secants was used to solve the four simultaneous equations describing the two-dimensional flow field around a pair of parallel counter-rotating vortices of equal and constant strength. The flow field information used by the algorithm could be derived from measurements from flow angle sensors mounted on the wing-tip of the detecting aircraft and an inertial navigation system. The study determined the propagated errors in the estimated location and strength of the vortex which resulted from random errors added to theoretically perfect measurements. The results are summarized in a series of charts and a table which make it possible to estimate these propagated errors for many practical situations. The situations include several generator-detector airplane combinations, different distances between the vortex and the detector airplane, as well as different levels of total measurement error.

Fuhrmann, Henri D.↗

NASA NTRS1995

Sound Generation by Flow over a Two-Dimensional Cavity

Sound generated by flow over a cavity at a Mach number of 0.1 and a Reynolds number based on cavity length of 5000 is calculated. The computation utilizes a two part technique where the time-dependent incompressible flow is first obtained and then a second calculation is performed for the compressible aspects of the flow. This second calculation utilizes a grid and numerical scheme designed for resolution of acoustic waves. The cavity flowfield is observed to oscillate quite regularly at the Strouhal number of 0.58 which produces an acoustic source of the same frequency. Time histories, spectra, and directivity of the sound radiation are computed.

Hardin, Jay C.↗

NASA NTRS1938

Wind-Tunnel Investigation of an N.A.C.A. 23012 Airfoil with a Slotted Flap and Three Types of Auxiliary Flap

An investigation was made in the N.A.C.A. 7- by 10- foot wind tunnel to determine the aerodynamic section characteristics of an N. A. C. A. 23012 airfoil with a single main slotted flap equipped successively with auxiliary flaps of the plain, split, and slotted types. A test installation mas used in which an airfoil of 7-foot span was mounted vertically between the upper and the lower sides of the closed test section so that two-dimensional flow was approximated. On the basis of maximum lift coefficient, low drag at moderate and high lift coefficients, and high drag at high lift coefficients, the optimum combination of the arrangements was found to be the double slotted flap . All the auxiliary flaps tested, however, increased the magnitudes of the pitching moments over those of the main slotted flap alone.

Wenzinger, Carl J.↗

NASA NTRS1938

Investigation in the 7-By-10 Foot Wind Tunnel of Ducts for Cooling Radiators Within an Airplane Wing, Special Report

An investigation was made in the NACA 7- by 10-foot wind tunnel of a large-chord wing model with a duct to house a simulated radiator suitable for a liquid-cooled engine. The duct was expanded to reduce the radiator losses, and the installation of the duct and radiator was made entirely within the wing to reduce form and interference drag. The tests were made using a two-dimensional flow set-up with a full-span duct and radiator. Section aerodynamic characteristics of the basic airfoil are given and also curves showing the characteristics of the various duct-radiator combinations. An expression for efficiency, the primary criterion of merit of any duct, and the effect of the several design parameters of the duct-radiator arrangement are discussed. The problem of throttling is considered and a discussion of the power required for cooling is included. It was found that radiators could be mounted in the wing and efficiently pass enough air for cooling with duct outlets located at any point from 0.25c to 0.70c from the wing leading edge on the upper surface. The duct-inlet position was found to be critical and, for maximum efficiency, had to be at the stagnation point of the airfoil and to change with flight attitude. The flow could be efficiently throttled only by a simultaneous variation of duct inlet and outlet sizes and of inlet position. It was desirable to round both inlet and outlet lips. With certain arrangements of duct, the power required for cooling at high speed was a very low percentage of the engine power.

Harris, Thomas A.↗

NASA NTRS2003

Analyzing Aeroelasticity in Turbomachines

ASTROP2-LE is a computer program that predicts flutter and forced responses of blades, vanes, and other components of such turbomachines as fans, compressors, and turbines. ASTROP2-LE is based on the ASTROP2 program, developed previously for analysis of stability of turbomachinery components. In developing ASTROP2- LE, ASTROP2 was modified to include a capability for modeling forced responses. The program was also modified to add a capability for analysis of aeroelasticity with mistuning and unsteady aerodynamic solutions from another program, LINFLX2D, that solves the linearized Euler equations of unsteady two-dimensional flow. Using LINFLX2D to calculate unsteady aerodynamic loads, it is possible to analyze effects of transonic flow on flutter and forced response. ASTROP2-LE can be used to analyze subsonic, transonic, and supersonic aerodynamics and structural mistuning for rotors with blades of differing structural properties. It calculates the aerodynamic damping of a blade system operating in airflow so that stability can be assessed. The code also predicts the magnitudes and frequencies of the unsteady aerodynamic forces on the airfoils of a blade row from incoming wakes. This information can be used in high-cycle fatigue analysis to predict the fatigue lives of the blades.

Reddy, T. S. R.↗

NASA NTRS2013

Assessment of tbe Performance of Ablative Insulators Under Realistic Solid Rocket Motor Operating Conditions (a Doctoral Dissertation)

Ablative insulators are used in the interior surfaces of solid rocket motors to prevent the mechanical structure of the rocket from failing due to intense heating by the high-temperature solid-propellant combustion products. The complexity of the ablation process underscores the need for ablative material response data procured from a realistic solid rocket motor environment, where all of the potential contributions to material degradation are present and in their appropriate proportions. For this purpose, the present study examines ablative material behavior in a laboratory-scale solid rocket motor. The test apparatus includes a planar, two-dimensional flow channel in which flat ablative material samples are installed downstream of an aluminized solid propellant grain and imaged via real-time X-ray radiography. In this way, the in-situ transient thermal response of an ablator to all of the thermal, chemical, and mechanical erosion mechanisms present in a solid rocket environment can be observed and recorded. The ablative material is instrumented with multiple micro-thermocouples, so that in-depth temperature histories are known. Both total heat flux and thermal radiation flux gauges have been designed, fabricated, and tested to characterize the thermal environment to which the ablative material samples are exposed. These tests not only allow different ablative materials to be compared in a realistic solid rocket motor environment but also improve the understanding of the mechanisms that influence the erosion behavior of a given ablative material.

Martin, Heath Thomas↗

NASA NTRSDate not supplied

Summary of Shock Wave Turbulent Boundary Layer Interaction Experiments In a Circular Test Section

A series of experiments were performed at Mach 2.5 in a 17 cm diameter circular test section to characterize an impinging/reflected shock wave turbulent boundary layer interaction generated by a cone-cylinder centerbody. The cone-cylinder centerbody generates a conical shock wave that interacts with the naturally occurring boundary layer developing on the test section wall. Three different cone angles were used in the experiment to study unseparated, incipiently separated, and separated interactions. When the cone-cylinder centerbody is positioned on the centerline, a flowfield which is two-dimensional in the mean is generated. Three dimensional interactions were also created by offsetting the cone-cylinder centerbody from the test section centerline. The results are intended to provide benchmark quality datasets for computational fluid dynamics (CFD) validation without the pitfalls inherent in rectangular configurations where corner effects prohibit a truly two-dimensional flow in the mean. The experimental measurements included surface flow visualization, wall static pressure, flowfield Pitot tube pressure, constant-voltage anemometry (CVA) normal hot-wire, and particle image velocimetry (PIV) measurements. The hot-wire measurements were used to calculate mean mass flux and total temperature profiles, mass flux and total temperature turbulence intensities, and the mass flux-total temperature correlation. The PIV measurements provide three-dimensional mean velocity measurements. Agreement between the pressure, hot-wire, and PIV measurements is established in the undisturbed upstream flowfield.

Supersonic↗

NASA NTRSDate not supplied

Summary of Shock Wave Turbulent Boundary Layer Interaction Experiments in a Circular Test Section

A series of experiments were performed at Mach 2.5 in a 17 cm diameter circular test section to characterize an impinging/reflected shock wave turbulent boundary layer interaction generated by a cone-cylinder centerbody. The cone-cylinder centerbody generates a conical shock wave that interacts with the naturally occurring boundary layer developing on the test section wall. Three different cone angles were used in the experiment to study unseparated, incipiently separated, and separated interactions. When the cone-cylinder centerbody is positioned on the centerline, a flowfield which is two-dimensional in the mean is generated. Three dimensional interactions were also created by offsetting the cone-cylinder centerbody from the test section centerline. The results are intended to provide benchmark quality datasets for computational fluid dynamics (CFD) validation without the pitfalls inherent in rectangular configurations where corner effects prohibit a truly two-dimensional flow in the mean. The experimental measurements included surface flow visualization, wall static pressure, flowfield Pitot tube pressure, constant-voltage anemometry (CVA) normal hot-wire, and particle image velocimetry (PIV) measurements. The hot-wire measurements were used to calculate mean mass flux and total temperature profiles, mass flux and total temperature turbulence intensities, and the mass flux-total temperature correlation. The PIV measurements provide three-dimensional mean velocity measurements. Agreement between the pressure, hot-wire, and PIV measurements is established in the undisturbed upstream flowfield.

compressible flow↗

NASA NTRSDate not supplied

Grid Refinement Techniques for the 𝜸-Re𝜽𝒕 Transition Model in FUN3D

There has been an increased focus on the overall accuracy and grid convergence of Reynolds-averaged Navier-Stokes (RANS)-based transition models from the recent AIAA and NATO-AVT workshops. Even though satisfactory grid convergence could be achieved for simple two-dimensional flow configurations, it required mesh counts that are substantially larger than those used in typical applications. In this paper, we focus our efforts on understanding how the grid resolution and topology influences the accuracy and convergence of results by studying the Schubauer and Skramstad flat-plate configuration and the NLF-0416 airfoil at an angle of attack equal to five degrees using FUN3D, a second-order finite-volume code. By focusing on these cases, we can analyze both natural and separation-induced transition scenarios. Multiple grid refinement strategies are investigated. First, we determine the relative effectiveness of zonal streamwise refinement in the transition region within structured grids as an alternative to the costly option of globally uniform refinement of a baseline grid. We also complement this zonal technique by globally varying the wall-normal resolution keeping the streamwise resolution fixed. The zonal streamwise refinement can accurately model natural transition in a flat-plate boundary layer and separation-induced transition, but struggles to accurately model natural transition in airfoil flows. A series of unstructured prismatic grids that have similar node counts and viscous wall spacings as the structured hexahedral grids are also tested, and they do not achieve grid convergence until an extremely fine resolution. Last, we employ adjoint-based unstructured grid adaptation in FUN3D to natural and separation-induced transition on the NLF-0416 airfoil. The adjoint-based refinement process converges to the same solution as the baseline family of structured grids, but leads to smaller errors on coarser grids.

Grid Adaptation↗

NASA NTRSDate not supplied

Grid Refinement Techniques for the 𝜸-Re 𝜽 𝒕 Transition Model in FUN3D

There has been an increased focus on the overall accuracy and grid convergence of Reynolds-averaged Navier-Stokes (RANS)-based transition models from the recent AIAA and NATO-AVT workshops. Even though satisfactory grid convergence could be achieved for simple two-dimensional flow configurations, it required mesh counts that are substantially larger than those used in typical applications. In this paper, we focus our efforts on understanding how the grid resolution and topology influences the accuracy and convergence of results by studying the Schubauer and Skramstad flat-plate configuration and the NLF-0416 airfoil at an angle of attack equal to five degrees using FUN3D, a second-order finite-volume code. By focusing on these cases, we can analyze both natural and separation-induced transition scenarios. Multiple grid refinement strategies are investigated. First, we determine the relative effectiveness of zonal streamwise refinement in the transition region within structured grids as an alternative to the costly option of globally uniform refinement of a baseline grid. We also complement this zonal technique by globally varying the wall-normal resolution keeping the streamwise resolution fixed. The zonal streamwise refinement can accurately model natural transition in a flat-plate boundary layer and separation-induced transition, but struggles to accurately model natural transition in airfoil flows. A series of unstructured prismatic grids that have similar node counts and viscous wall spacings as the structured hexahedral grids are also tested, and they do not achieve grid convergence until an extremely fine resolution. Last, we employ adjoint-based unstructured grid adaptation in FUN3D to natural and separation-induced transition on the NLF-0416 airfoil. The adjoint-based refinement process converges to the same solution as the baseline family of structured grids, but leads to smaller errors on coarser grids.

Grid Adaptation↗

NASA NTRS1974

Numerical computation of two dimensional viscous blunt body flows with an impinging shock, part 2

Two-dimensional viscous blunt body flows with an impinging shock have been computed using a time-dependent finite-difference method which solves the complete set of Navier-Stokes equations for a compressible flow. For low Reynolds number flows, the entire flow field, including the bow shock and impinging shock, has been captured in the computation. For higher Reynolds number flows, the bow shock is treated as a discontinuity across which the Rankine-Hugoniot equations are applied, while the boundary layer and interaction regions are captured as before. Using this latter shock-fitting approach, a Type III shock interaction flow field has been computed with flow conditions corresponding to the space shuttle orbiter freestream conditions at 61 km (200,000 ft).

Holst, T. L.↗

NASA NTRS1989

A simple algebraic grid adaptation scheme with applications to two- and three-dimensional flow problems

An algebraic adaptive grid scheme based on the concept of arc equidistribution is presented which provides high flowfield resolution when applied to two-dimensional and three-dimensional flow problems. The present scheme locally adjusts the grid density using gradients of selected flow variables from either finite difference or finite volume calculations, and it can specify user-prescribed grid stretching such that control of the grid spacing can be maintained in areas of known flowfield behavior. A robust and efficient grid smoothing technique has been incorporated into the adaptive grid routine.

Hsu, Andrew T.↗

NASA NTRS1988

Investigation of two-dimensional chemically reacting and radiating supersonic channel flows

The two-dimensional time-dependent Navier-Stokes equations are solved in order to study supersonic flows with finite rate chemistry and radiation for hydrogen-air systems. The problem of the flow in a channel with a ten-degree compression-expansion ramp is solved using the finite volume technique of Jameson et al. (1981) and the unsplit finite difference scheme of MacCormack (1969). The problem of chemically reacting and radiating flows is considered for the flow of premixed hydrogen-air through a channel with parallel boundaries and a channel with a compression corner. Results suggest that radiative interaction can have a significant effect on the entire flowfield.

Mani, M.↗

NASA NTRS1990

Time-accurate Navier-Stokes computations of self-excited two-dimensional unsteady cavity flows

Time-accurate Navier Stokes computations were performed to study self-excited oscillatory shear layer behavior over a two-dimensional rectangular cavity and to gain insight into the vortex-acoustic coupling that sustains these oscillations. Results were obtained solving the full, unsteady compressible Navier-Stokes equations for Reynolds-averaged turbulent air flow past a cavity with L/d = 2. Conditions duplicated test conditions in experiments by Rossiter at Mach numbers varied from 0.6 to 1.2. The computational scheme was the USA 2D series code developed by Rockwell's Science Center with an algebraic turbulence model for the shear layer and recirculating region. Two physical conditions were simulated: an isolated cavity situated (1) in an infinite plane wall and (2) in an infinite channel with an opposing parallel wall. Computed results for (1) showed excellent agreement with Rossiter's measured amplitudes and frequencies. A tuned acoustic duct resonance effect was observed in (2), demonstrating a controlled change in the acoustic feedback mechanism and resultant amplification in computed oscillations.

Dougherty, N. Sam↗

NASA NTRS1982

Comparison of two and three dimensional flow computations with laser anemometer measurements in a transonic compressor rotor

A procedure for using an efficient axisymmetric code to generate downstream pressure input for more costly Euler codes is discussed. Two and three dimensional inviscid solutions for the flow within a transonic axial compressor rotor at design speed are compared to laser anemometer measurements at maximum flow and near stall operating points. Computational details of the 2-D axisymmetric stream function solution and the 3-D full Euler solution are described. Relative Mach number contours, shock location, and shock strength as measured and as predicted by the 3-D code are compared. Downstream of the rotor the inviscid computations agree with each other but predict higher pressure ratios than those measured. Euler codes require a downstream pressure as input. Since that pressure controls the computed mass flow and shock system, it must be consistent with an inviscid solution.

Chima, R. V.↗

NASA NTRS1970

A numerical solution of unsteady flow in a two-dimensional square cavity

Two dimensional unsteady fluid flow in square cavity numerically analyzed from continuity and Navier-Stokes equations and recorded as computer-generated motion picture

Donovan, L. F.↗

NASA NTRS1951

Investigation of Turbulent Flow in a Two-Dimensional Channel

A detailed exploration of the field of mean and fluctuating quantities in a two-dimensional turbulent channel flow is presented. The measurements were repeated at three Reynolds numbers, 12,300, 30,800, and 61,600, based on the half width of the channel and the maximum mean velocity. A channel of 5-inch width and 12:1 aspect ratio was used for the investigation. Mean-speed and axial-fluctuation measurements were made well within the laminar sublayer. The semitheoretical predictions concerning the extent of the laminar sublayer were confirmed. The distribution of the velocity fluctuations in the direction of mean flow u' shows that the influence of the viscosity extends farther from the wall than indicated by the mean velocity profile, the region of influence being approximately four times as wide.

Laufer, John↗

NASA NTRS1990

Surface representations of two- and three-dimensional fluid flow topology

We discuss our work using critical point analysis to generate representations of the vector field topology of numerical flow data sets. Critical points are located and characterized in a two-dimensional domain, which may be either a two-dimensional flow field or the tangential velocity field near a three-dimensional body. Tangent curves are then integrated out along the principal directions of certain classes of critical points. The points and curves are linked to form a skeleton representing the two-dimensional vector field topology. When generated from the tangential velocity field near a body in a three-dimensional flow, the skeleton includes the critical points and curves which provide a basis for analyzing the three-dimensional structure of the flow separation. The points along the separation curves in the skeleton are used to start tangent curve integrations to generate surfaces representing the topology of the associated flow separations.

Helman, James L.↗