Search NASA⌕ Search

SEARCH · Search NASA

Results for “Water Impact Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Uranium Distribution Coefficient (Kd) Determination and Use in Assessing Transport, Fate, and Risk at Jefferson Proving Ground, I - 18593

Jefferson Proving Ground (JPG), located near Madison, Indiana is a 55,000-acre site with firing ranges for test firing of conventional munitions and depleted uranium penetrators. The penetrators were fired from three positions, but the majority (89 percent) was fired from a single location. Impacts from the penetrators along this firing line created an impact trench roughly 5 meters (m) to 8 m wide, 1,200 m long, and 1 m deep. Periodic surface sweeps were conducted to recover test fired penetrators, but roughly 73,500 kilograms (kg) of depleted uranium (DU) still remain at JPG. Co-located and intermingled with the penetrators are unexploded ordnance (UXO), making complete recovery and site restoration both risky and costly. Understanding the transport and fate of the depleted uranium at JPG was critical to assessing the potential radiological risks posed to human health and the environment from the penetrators and associated impacted soils on site. JPG is underlain by loess (wind-blown silt), glacial till, and carbonate bedrock, and transected by surface water (Big Creek, Middle Fork Creek, and smaller tributaries). The Army determined site-specific values of the uranium distribution coefficient (Kd) for each of the underlying units. The Army evaluated uranium transport and fate in column, groundwater, and surface water models. The Army used the Residual Radiation (RESRAD)- OFFSITE code to complete the uranium risk assessment for a period of 1,000 years. Results from the site-specific Kd tests are presented in this paper along with its use and results in assessing transport, fate, and potential risks associated with exposure to the penetrators remaining at JPG. The authors supported the decommissioning activities discussed in this paper under the direction of and with funding from the U.S. Army, specifically the U.S. Army Installation Management Command (IMCOM, Robert N. Cherry), U.S. Army Environmental Command (AEC, Joan F. Jackson), and U.S. Army Corps of Engineers (USACE, Andrew [Brooks] Evens). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Use of scaled BWR lower plenum boron mixing tests to qualify the boron transport model used in TRACG

In 2001 GEH applied best estimate methods combined with a statistical methodology to determine upper bound limits for key licensing parameters for anticipated operation occurrence (AOO) transient and anticipated transients without scram (ATWS) overpressure analyses for operating Boiling Water Reactors (BWRs). The methodology was subsequently extended for ESBWR AOO, ATWS, loss of coolant, and stability analyses. GEH is extending the methodology to long-term ATWS analyses for the operating BWRs. A long-term ATWS scenario uses injection of borated water to achieve reactor shutdown. Predicting the mixing and transport of boron is important for calculating the impact on the key licensing parameters. For the many operating BWRs where the denser boron solution is injected into the lower plenum, stratification may occur, delaying boron transport to the core region. CFD modeling can be used to model the stratification and mixing of the boron solution, but such calculations are extremely computer intensive and not cost effective; therefore, a more-empirical approach supported by a theoretical scaling of the dominant phenomena and backed by test data and benchmark calculations is used. The paper presents the TRACG lower plenum boron transport model qualification effort. The scaling basis used to implement the TRACG boron transport model for BWR applications is discussed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Briquetting characteristics of woody and herbaceous biomass blends: Impact on physical properties, chemical composition, and calorific value

Abstract Intercropping (or polyculture) is gaining a lot of interest as it increases yields, allows better utilization of resources (water and nutrients), and provides better land management. The objective of this study is to understand the briquetting characteristics of woody and herbaceous biomass blends, which might result from intercropping. Tests were conducted on blends of lodgepole pine, switchgrass, and corn stover biomass using three hammer mill screen sizes (i.e., 4.8, 12.7, and 19.05 mm), three blend moistures (12%, 15%, and 18%, w.b.), and two‐ and three‐blend ratios (i.e., 1:1 and 1:1:1) using a pilot‐scale hydraulic briquette press. The briquette properties, such as unit and bulk density, durability rating after 5 days of storage (as they tend to attain stable density), and the energy consumption of the process were measured. The results indicate that moisture content of 12% and 15% (w.b.) and smaller hammer mill screen size of 4.8 mm increased the unit and bulk densities to >750 and >430 kg/m 3 and moisture content (15% and 18% (w.b.)) and hammer mill screen size of 12.7 and 19.05 mm produced briquettes with durability rating values of >95%. The higher moisture content of 18% (w.b.) and the hammer mill screen size of 12.7 and 19.05 mm had the highest energy consumption. The proximate and ultimate analysis showed that energy content improved by blending lodgepole pine with both corn stover and switchgrass and also showed increased calorific value and reduced ash content. Scanning electron microscopy micrographs showed interlocking of particles and cracks in the briquettes. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd

Tumuluru, Jaya Shankar↗

Preparation for Pick-and-Eat Food Production on the International Space Station: Flight Definition for the VEG-04 and VEG-05 Missions

Growth of fresh, nutritious, palatable produce for crew consumption during spaceflight may provide health-promoting, bioavailable nutrients and enhance the dietary experience as we move toward longer-duration missions. Tending plants also may serve as a countermeasure for crew psychological stresses associated with long duration spaceflight. However, requirements to support consistent growth of a variety of high quality, nutritious crops under spaceflight environmental conditions is unknown. This study is exploring the potential to grow plants for food production on the International Space Station (ISS) using the Veggie vegetable production system. Ground testing is underway to compare the impacts of several fertilizer and lighting treatments on growth, quality, and nutritional composition of the leafy green crop mizuna, and the dwarf tomato crop Red Robin when subjected to Veggie ISS environmental conditions. Early testing focused on the leafy crop Tokyo Bekana Chinese cabbage, but ground tests indicated that this plant suffered from stress responses when grown under LEDs and the chronically elevated CO2 levels found on the ISS. Mizuna, a related leafy variety that grows well in the presence of high CO2, and has excellent organoleptic characteristics, was selected as an alternate crop. Tomato crops have been grown using two fertilizer formulations and two pollination techniques, and growth tests using different red:blue lighting environments are underway. Chemical analysis is also being conducted and these data, when coupled with the growth results, will be used to down-select to the two best lighting treatments and best fertilizer treatment for future testing of each crop on the ISS. Additionally, seed-source testing has become important, with mizuna seeds from two different vendors growing very differently. A seed source has been selected, and seed-surface-sanitizing methods have been confirmed for mizuna, but these remain under development for tomato. A crop-handling protocol is also being evaluated to support food safety. All harvests reserve a subset of samples for microbial analysis to determine baseline microbial levels and help establish critical control points for food safety. Testing was initially conducted in hardware analogs of the standard Veggie plant pillows. However, a new Veggie watering system, the Passive Orbital Nutrient Delivery System or PONDS, has been designed and is being prepared for future flight experiments. With the selection of this growth system, ground tests have shifted to analog PONDS systems. Crop tests on ISS, designated VEG-04 for mizuna and VEG-05 for tomato, are planned in 2018 to evaluate any additional impacts of spaceflight on the light and fertilizer conditions down-selected from ground tests. A set of Veggie-specific questions has been developed to characterize the psychological impacts of plant growth and plant-care activities during spaceflight. Organoleptic questionnaires have been developed to assess produce attributes in microgravity taste sessions. These tests for plants growing in the Veggie hardware on ISS will help to mitigate the risk of an inadequate food supply for long duration missions by developing methods and determining hardware requirements to integrate fresh vegetables as a dietary supplement. This research was co-funded by the Human Research Program and Space Biology (MTL1075) in the ILSRA 2015 NRA call.

Veggie↗

Preparation for Pick-and-Eat Food Production on the International Space Station: Flight Definition for the VEG-04 and VEG-05 Missions

Growth of fresh, nutritious, palatable produce for crew consumption during spaceflight may provide health-promoting, bioavailable nutrients and enhance the dietary experience as we move toward longer-duration missions. Tending plants also may serve as a countermeasure for crew psychological stresses associated with long duration spaceflight. However, requirements to support consistent growth of a variety of high quality, nutritious crops under spaceflight environmental conditions is unknown. This study is exploring the potential to grow plants for food production on the International Space Station (ISS) using the Veggie vegetable production system. Ground testing is underway to compare the impacts of several fertilizer and lighting treatments on growth, quality, and nutritional composition of the leafy green crop mizuna, and the dwarf tomato crop "Red Robin" when subjected to Veggie ISS environmental conditions. Early testing focused on the leafy crop "Tokyo Bekana" Chinese cabbage, but ground tests indicated that this plant suffered from stress responses when grown under LEDs and the chronically elevated CO2 levels found on the ISS. Mizuna, a related leafy variety that grows well in the presence of high CO2, and has excellent organoleptic characteristics, was selected as an alternate crop. Tomato crops have been grown using two fertilizer formulations and two pollination techniques, and growth tests using different red:blue lighting environments are underway. Chemical analysis is also being conducted and these data, when coupled with the growth results, will be used to down-select to the two best lighting treatments and best fertilizer treatment for future testing of each crop on the ISS. Additionally, seed-source testing has become important, with mizuna seeds from two different vendors growing very differently. A seed source has been selected, and seed-surface-sanitizing methods have been confirmed for mizuna, but these remain under development for tomato. A crop-handling protocol is also being evaluated to support food safety. All harvests reserve a subset of samples for microbial analysis to determine baseline microbial levels and help establish critical control points for food safety. Testing was initially conducted in hardware analogs of the standard Veggie plant pillows. However, a new Veggie watering system, the Passive Orbital Nutrient Delivery System or PONDS, has been designed and is being prepared for future flight experiments. With the selection of this growth system, ground tests have shifted to analog PONDS systems. Crop tests on ISS, designated VEG-04 for mizuna and VEG-05 for tomato, are planned in 2018 to evaluate any additional impacts of spaceflight on the light and fertilizer conditions down-selected from ground tests. A set of Veggie-specific questions has been developed to characterize the psychological impacts of plant growth and plant-care activities during spaceflight. Organoleptic questionnaires have been developed to assess produce attributes in microgravity taste sessions. These tests for plants growing in the Veggie hardware on ISS will help to mitigate the risk of an inadequate food supply for long duration missions by developing methods and determining hardware requirements to integrate fresh vegetables as a dietary supplement. This research was co-funded by the Human Research Program and Space Biology (MTL#1075) in the ILSRA 2015 NRA call.

LED light↗

Effects of long-term thermal aging on bulk and local mechanical behavior of ferritic-austenitic duplex stainless steels

Ferritic-austenitic duplex stainless steels (DSS) undergo significant thermal aging embrittlement in service in light water reactors. Specimens of cast CF–3 and CF–8 DSS have been laboratory aged for up to 17,200 h at four different temperatures (280, 320, 360, 400 °C) in order to characterize the aging evolution and mechanical properties. Standard Charpy V-Notch (CVN) impact testing and tensile testing are employed to measure the progression of embrittlement of the steels. Concurrently, nanoindentation measurements are performed to measure the hardening of the individual ferrite and austenite phases. Atom probe tomography (APT) analysis of the ferrite and austenite phases elucidates the relationship between spinodal decomposition of the ferrite and the mechanical effects of aging. The results are discussed to relate the effects of the local microstructure and property changes in the ferrite phase on the overall bulk mechanical evolution of these steels.

Schwarm, Samuel C.↗

Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanford’s 300 Area Uranium Plume

The Integrated Field Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex subsurface biogeochemical setting where groundwater and riverwater interact. A series of forefront science questions on reactive mass transfer motivates research. These questions relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated biogeochemical system. The project was initiated in February 2007, with CY 2007, CY 2008, CY 2009, and CY 2010 progress summarized in preceding reports. A project peer review was held in March 2010, and the IFRC project acted upon all suggestions and recommendations made in consequence by reviewers and SBR/DOE. These responses have included the development of 'Modeling' and 'Well-Field Mitigation' plans that are now posted on the Hanford IFRC web-site, and modifications to the IFRC well-field completed in CY 2011. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2011 including: (i) well modifications to eliminate well-bore flows, (ii) hydrologic testing of the modified well-field and upper aquifer, (iii) geophysical monitoring of winter precipitation infiltration through the U-contaminated vadose zone and spring river water intrusion to the IFRC, (iv) injection experimentation to probe the lower vadose zone and to evaluate the transport behavior of high U concentrations, (v) extended passive monitoring during the period of water table rise and fall, and (vi) collaborative down-hole experimentation with the PNNL SFA on the biogeochemistry of the 300 A Hanford-Ringold contact and the underlying redox transition zone. The modified well-field has functioned superbly without any evidence for well-bore flows. Beyond these experimental efforts, our site-wide reactive transport models (PFLOTRAN and eSTOMP) have been updated to include site geostatistical models of both hydrologic properties and adsorbed U distribution; and new hydrologic characterization measurements of the upper aquifer. These increasingly robust models are being used to simulate past and recent U desorption-adsorption experiments performed under different hydrologic conditions, and heuristic modeling to understand the complex functioning of the smear zone. We continued efforts to assimilate geophysical logging and 3D ERT characterization data into our site wide geophysical model, with significant and positive progress in 2011 that will enable publication in 2012. Our increasingly comprehensive field experimental results and robust reactive transport simulators, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes influencing N, S, C, Mn, and Fe. Collectively these findings and higher scale models are providing a unique and unparalleled system-scale understanding of the biogeochemical function of the groundwater-river interaction zone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and ullage gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗

Initial Application of TSUNAMI for Validation of Advanced Fuel Systems

A number of advanced reactor concepts and accident-tolerant fuels (ATFs) are under development or in the initial stages of deployment and testing in the nuclear power industry. Many of these concepts incorporate chemical or material forms that have not traditionally been used in the nuclear industry and may present challenges for nuclear criticality safety validation. Sensitivity/uncertainty methods are ideally suited for assessing the applicability of existing critical experiments to these potentially challenging applications. This paper presents two case studies recently completed at Oak Ridge National Laboratory (ORNL) which investigated the use of the TSUNAMI tools within the SCALE code system to perform such assessments.Many advanced reactor concepts include uranium enrichments above 5 wt% 235U but below the 20 wt% limit of low-enriched uranium (LEU). This material, referred to as high assay LEU (HA-LEU), poses difficulties across the entire infrastructure of nuclear power, including enrichment, transportation, fabrication, and storage. A potentially representative transportation package was selected to perform a criticality safety validation assessment for UF6 containing HA-LEU. Sensitivity data were generated using the TSUNAMI-3D sequence, and an assessment of the applicability of a range of critical experiments was performed using the TSUNAMI-IP tool. The critical experiments were drawn from the set of available sensitivity data files distributed with the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The results indicate that a sufficient number of available experiments may be available to perform validations for these systems.Many different cladding materials and fuel dopants are included in ATFs to mitigate the consequences of a loss of coolant accident. Some of these systems have already been fabricated and introduced as lead test assemblies in commercial reactors, while others are still being developed. Several concepts were considered for pressurized-water reactors (PWRs) and boiling-water reactors (BWRs) in comparison to the current Zircaloy and UO2 fuel system. In most of these cases, the ATF materials did not significantly impact the number of applicable experiments for validation. Some fuel and cladding materials were identified, however, which may reduce the number of available experiments and which will increase the nuclear data–induced uncertainty in neutron multiplication.

Marshall, William (B.J.)↗

Minimizing Transuranic Waste Generated in Hot Cells at Oak Ridge National Laboratory Through Use of a Non-Destructive CO{sub 2} Pellet Cleaning System - 19577

Wastes generated in shielded hot cells containing materials contaminated with transuranic (TRU) waste present unique problems in waste disposal at Department of Energy (DOE) sites. Oak Ridge National Laboratory (ORNL) routinely processes materials contaminated with TRU waste from the High Flux Isotope Reactor (HFIR) and from other sources (both on and off-site) in their hot cell facilities, generating wastes that require eventual disposal. The waste streams generated by these processes are often high activity and exhibit high dose rates, driving them into the remote-handled (RH) category at the Waste Isolation Pilot Plant (WIPP). Reduction of the TRU waste footprint is desirable from a disposal cost perspective due to constraints with RH waste processing and a lack of space availability at the WIPP. Historically TRU waste generated at ORNL has been processed by the TRU Waste Processing Center (TWPC), which belongs to the Department of Energy's Office of Environmental Management (DOE-EM). Now that Oak Ridge legacy TRU waste is reaching its final stage, DOE-EM has turned over the mission of processing newly-generated TRU waste streams to the DOE Office of Science at ORNL. To reduce the volume of potential TRU waste occupying valuable space in the ORNL Hot Cells, a non-destructive CO{sub 2} pellet cleaning system will be used to capture particulate contaminants removed from the surfaces of waste inside the ORNL Non-Reactor Nuclear Facilities (NNFD) Hot Cells at the Irradiated Fuels Examination Laboratories (IFEL). The particulate will be segregated by particle size and captured for disposal later. This action will separate some of the TRU isotopes (particulate) from the larger waste volume (debris waste items), resulting in both lower waste disposal costs and reduced TRU waste volumes. This will be accomplished through a specialized cyclone separator. Secondary wastes are usually generated through other methods of decontamination, such as water jets and abrasive agents. These secondary wastes are absent with the CO{sub 2} pelletized system, due to sublimation of the dry ice upon impact. This is an important consideration with IFEL, a facility whose primary mission is to perform a series of R and D testing on nuclear fuel rods. Liquid is not a feasible method of decontamination as the IFEL's drains in the Hot Cells were plugged years ago due to Resource Conservation and Recovery Act (RCRA) regulations. Constraints at IFEL, such as criticality safety concerns with use of hydrogenous materials, are also alleviated with the non-destructive CO{sub 2} pellet cleaning system. These are a couple of the considerations why this method of decontamination is preferred. Due to concerns with oxidizers at WIPP grouting will be performed on the contaminated particulate produced during the trapping by the cyclone separation phase. This method will comply with mitigating oxidizing properties in TRU waste, required by the recently published Basis of Knowledge (BoK) document as part of Acceptable Knowledge (AK) by WIPP. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Comparison of ring compression testing to three point bend testing for unirradiated ZIRLO cladding

Safe shipment and storage of nuclear reactor discharged fuel requires an understanding of how the fuel may perform under the various conditions that can be encountered. One specific focus of concern is performance during a shipment drop accident. Tests at Savannah River National Laboratory (SRNL) are being performed to characterize the properties of fuel clad relative to a mechanical accident condition such as a container drop. Unirradiated ZIRLO tubing samples have been charged with a range of hydride levels to simulate actual fuel rod levels. Samples of the hydrogen charged tubes were exposed to a radial hydride growth treatment (RHGT) consisting of heating to 400°C, applying initial hoop stresses of 90 to 170 MPa with controlled cooling and producing hydride precipitates. Initial samples have been tested using both a) ring compression test (RCT) which is shown to be sensitive to radial hydride and b) three-point bend tests which are less sensitive to radial hydride effects. Hydrides are generated in Zirconium based fuel cladding as a result of coolant (water) oxidation of the clad, hydrogen release, and a portion of the released (nascent) hydrogen absorbed into the clad and eventually exceeding the hydrogen solubility limit. The orientation of the hydrides relative to the subsequent normal and accident strains has a significant impact on the failure susceptability. In this study the impacts of stress, temperature and hydrogen levels are evaluated in reference to the propensity for hydride reorientation from the circumferential to the radial orientation. In addition the effects of radial hydrides on the Quasi Ductile Brittle Transition Temperature (DBTT) were measured. The results suggest that a) the severity of the radial hydride impact is related to the hydrogen level-peak temperature combination (for example at a peak drying temperature of 400°C; 800 PPM hydrogen has less of an impact/ less radial hydride fraction than 200 PPM hydrogen for the same thermal history) and b) for critical strains in post drying handling, storage and accident conditions the 3 point bend strain tolerance is less affected by radial hydrides than the conventional ring compression test (the radial hydride related Quasi DBTT associated with a three point bend straining is lower (better) than that measured by the ring compression tests).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗

lllinois Storage Corridor CarbonSAFE Phase III: Pre-drilling Site Assessment: Prairie State Generating Company

The Illinois Storage Corridor project will drill a stratigraphic test well as part of the Illinois Storage Corridor CarbonSAFE Phase 3 project near the Prairie State Generating Company coal-fired power plant near Marissa, Illinois. The pre-drilling site evaluation has considered the primary target reservoirs, the Potosi Dolomite and St. Peter Sandstone, and primary seal, the Maquoketa Group. Data to be collected from the well include core, fluid samples, in situ well tests, geophysical logs intended to provide information on lithologic, geomechanical, and geophysical characteristics to determine the feasibility for the geologic sequestration of 50 million metric tons or more of injected carbon dioxide. The planned drilling site has been evaluated using available subsurface geologic data and analyses from the Illinois Basin. These data provide lithologic and structural information, shallow groundwater resource distribution, location of known nearby wellbores, and regional drilling characteristics. The data were used to generate geologic structure and isopach maps for the target reservoir and caprock strata and for prognosing the tops of major lithologic units to aid drilling and coring procedures. The regional analyses indicate that no known structural features are expected to negatively impact the target storage reservoir or caprock. No protected and sensitive areas, groundwater resources, or existing resource development are expected to be impacted by the proposed well drilling activities. The well is planned to be drilled to a total depth of approximately 5,600 feet (1,707 m) and terminate in the Precambrian. Cores (up to 5 intervals) will be collected from the Maquoketa Group, confining units above the St. Peter Sandstone, St. Peter Sandstone, confining units of the Potosi Dolomite and the Potosi Dolomite. Water samples will be attempted to be collected from the St. Peter Sandstone and Potosi Dolomite. Potential impact on drilling progress is a lost circulation zone in the Potosi Dolomite, which has been demonstrated to have intermittent cavernous porosity from karstification elsewhere in the Illinois Basin. This document also presents a preliminary coring and sampling program, proposed logging suite, and well testing program, all of which will be reviewed during drilling.

01 COAL, LIGNITE, AND PEAT↗

Quantifying mortality and injury susceptibility for two morphologically disparate fishes exposed to simulated turbine blade strike

Passage of fishes through hydropower turbines and water pumping stations may cause mortal injury as the result of exposure to blade strike impact. Laboratory trials of simulated blade strike on two morphologically distinct fishes, American eel ( Anguilla rostrata ) and bluegill sunfish ( Lepomis macrochirus ) were undertaken to assess injury and mortality rates. We hypothesized that bluegill would have comparable rates of injury and mortality to other laterally compressed fishes while anguilliform American eel would be more resistant to injury. American eel had low observed mortality rates at the highest velocity tested (13.6 m/s), but many fish were observed with vertebral fractures which we categorized as functionally dead individuals. Bluegill were more susceptible to blade strike with high rates of mortality regardless of blade thickness, velocity, or impact conditions (location, angle, or fish orientation). These data have broadened our understanding of the range of responses among entrained fishes exposed to blade strike and represent species with low (American eel) and high (bluegill) susceptibility to injury and mortality. Furthermore, our blade strike data can help inform safer turbine designs or prioritization of pumps that minimize traumatic injury and mortality of fishes during non-volitional passage through hydropower turbines or water pumping stations.

59 BASIC BIOLOGICAL SCIENCES↗

Assessment of the Corrosion Risks to a Double Shell Tank During the Selective Removal of a Cesium-rich Supernate Layer - 20227

The Direct Feed Low Activity Waste (DF-LAW) activity will provide the initial feed to the Waste Treatment and Immobilization Plant at the Hanford Tank Farm facility. Feed preparation for DF-LAW will be carried out in multiple double shell waste tanks (DST) utilizing the Tank Side Cesium Removal (TSCR) process. Tank AP-106 will be an integral part of the TSCR process and hence key to the DFLAW activity. Prior to being utilized for this purpose, the Cs-137 concentration levels in the AP-106 supernate must be reduced significantly. The AP-106 re-purposing process manages normal waste tank addition procedures such that waste acceptance criteria objectives for Cs-137 removal are achieved. As this process was being developed, several concerns regarding tank integrity during and after repurposing of Tank AP-106, and the associated tanks (i.e., AP-102, AN-101, and AP-108), were addressed. The potential corrosion degradation mechanisms identified based on process knowledge included: general and pitting corrosion, caustic stress corrosion cracking, concentration cell corrosion, and microbiologically induced corrosion (MIC). A systematic approach was undertaken to assess the risk of corrosion during the AP-106 re-purposing process. The assessment considered the initial and present condition of the tank, the service history of the tank, the environmental conditions created in each tank during each stage of the process, process timing, and corrosion testing and modeling that approximated tank conditions. Based on this information, recommendations were provided to minimize the exposure of the tank to corrosive conditions. These recommendations included time limits for each stage of the process, staging of corrosion inhibitor solutions should process delays occur, and waste sampling with potential chemistry adjustments at defined steps in the process. Additionally, recommendations for post-process supernate chemistry adjustments and tank inspections were put forth. The greatest risk for this process occurs during the manipulation of large quantities of Columbia River water (i.e., greater than 450,000 gallons) within AP-106, the associated tanks and the supporting infrastructure (i.e., transfer line piping). This risk becomes more pronounced if there is a process upset and the tank walls remain exposed to a corrosive condition longer than intended. As long as the river water is blended into the supernate in a timely fashion, and the waste is adjusted appropriately with corrosion inhibitors, corrosion may be minimized and the final condition of the supernate in AP-106 and the associated tanks is expected to be in compliance with corrosion chemistry requirements. Contingency plans will be made to minimize the impact of a process upset. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Heterogeneity‐enhanced gas phase formation in shallow aquifers during leakage of CO 2 ‐saturated water from geologic sequestration sites

Abstract A primary concern for geologic carbon storage is the potential for leakage of stored carbon dioxide (CO 2 ) into the shallow subsurface where it could degrade the quality of groundwater and surface water. In order to predict and mitigate the potentially negative impacts of CO 2 leakage, it is important to understand the physical processes that CO 2 will undergo as it moves through naturally heterogeneous porous media formations. Previous studies have shown that heterogeneity can enhance the evolution of gas phase CO 2 in some cases, but the conditions under which this occurs have not yet been quantitatively defined, nor tested through laboratory experiments. This study quantitatively investigates the effects of geologic heterogeneity on the process of gas phase CO 2 evolution in shallow aquifers through an extensive set of experiments conducted in a column that was packed with layers of various test sands. Soil moisture sensors were utilized to observe the formation of gas phase near the porous media interfaces. Results indicate that the conditions under which heterogeneity controls gas phase evolution can be successfully predicted through analysis of simple parameters, including the dissolved CO 2 concentration in the flowing water, the distance between the heterogeneity and the leakage location, and some fundamental properties of the porous media. Results also show that interfaces where a less permeable material overlies a more permeable material affect gas phase evolution more significantly than interfaces with the opposite layering.

Plampin, Michelle R.↗