Search NASA⌕ Search

SEARCH · Search NASA

Results for “actuated”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

A lightweight bimetallic actuator for spacecraft thermal control

The design, development, and construction of two types of active thermal-control systems are described. These designs are based on the controlled angular deflections of spiral-wound bimetallic actuators. The use of these actuators and lightweight louvers results in a frictionless system that is low in weight yet simple in design and low in cost. Both designs exhibit high reliability, good performance repeatability, and do not require power from the spacecraft. Design philosophy and implementation, design tradeoffs, and materials selection are reviewed. The test program is described, and results are presented.

Schilling, K. L.↗
NASA NTRS1972

Application of polyimide actuator rod seals

Development of polyimide two-stage hydraulic actuator rod seals for application in high-performance aircraft was accomplished. The significant portion of the effort was concentrated on optimization of the chevron and K-section second-stage seal geometries to satisfy the requirements for operation at 450 K (350 F) with dynamic pressure loads varying between 200 psig steady-state and 1500 psig impulse cycling. Particular significance was placed on reducing seal gland dimension by efficiently utilizing the fatigue allowables of polyimide materials. Other objectives included investigation of pressure balancing techniques for first-stage polyimide rod seals for 4000 psig 450 K(350 F) environment and fabrication of a modular retainer for the two-stage combination. Seals were fabricated in 0.0254 m (1.0in.) and 0.0635 m (2.5in.) sizes and tested for structural integrity, frictional resistance, and endurance life. Test results showed that carefully designed second stages using polyimides could be made to satisfy the dynamic return pressure requirements of applications in high-performance aircraft. High wear under full system pressure indicated that further research is necessary to obtain an acceptable first-stage design. The modular retainer was successfully tested and showed potential for new actuator applications.

Watermann, A. W.↗
NASA NTRS1972

High torque CMG rotary actuator

A high torque rotary actuator was designed, fabricated and tested. Exacting requirements were placed on performance and physical characteristics of the actuator, particularly in the area of stiffness, backlash, torque ripple, power and size and weight. A brushless dc motor was designed utilizing rare earth magnets to meet power and weight requirements. A 26-to-1 planetary roller gear transmission was selected to best meet overall requirements. The transmission utilizes parallel gear and roller paths to minimize backlash and breakaway torque.

Source record↗
NASA NTRS1972

Development of a space qualified high reliability rotary actuator. Volume 1: Technical report

A space-qualified, high reliability, 150 ft-lb rated torque rotary acutator based on the Bendix Dynavector drive concept was developed. This drive is an integrated variable reluctance orbit motor-epicyclic transmission actuator. The performance goals were based on future control moment gyro torquer applications and represent a significant advancement in the torque-to-weight ratio, backlash, inertia and response characteristics of electric rotary drives. The program accomplishments have been in two areas: (1) the development of two high ratio (818:1) actuator configurations (breadboard and flightweight), and (2) the invention of a reliable proximity switch sensor system for self-commutation without use of optical or electrical brush techniques.

Presley, R. W.↗
NASA NTRS1972

Nonlinear actuator disk theory.

Results obtained from a recent investigation of the flowfield induced by a heavily loaded actuator disk. First, the governing nonlinear integral equations are formulated from two different points of view, and the iterative solution is briefly outlined. Calculated flow patterns are presented for representative advance ratios and blade circulation distributions. For the static condition, the experimentally observed lingering of the tip vortices in the propeller plane, and the insensitivity of the streamline pattern to thrust coefficient are both accounted for, and a 'dividing streamline' - apparently not previously discussed in the literature, is predicted for the nonstatic case. Finally, the relationship between the actuator disk flow and the zero harmonic of the flowfield induced by a finite-bladed propeller is considered.

Greenberg, M. D.↗
NASA NTRS1973

Thermally responsive mechanical actuator

Device built for use in heat control, heat measurement, and mechanical actuation by heat include thermometers, thermostats, safety switches, circuit breakers, and mechanical actuators. Silicon rubber has highest coefficient of expansion of any known material and seems suitable for most of these devices.

Madey, J. M.↗
NASA NTRS1972

An actuator extension transformation for a motion simulator and an inverse transformation applying Newton-Raphson's method

A set of equations which transform position and angular orientation of the centroid of the payload platform of a six-degree-of-freedom motion simulator into extensions of the simulator's actuators has been derived and is based on a geometrical representation of the system. An iterative scheme, Newton-Raphson's method, has been successfully used in a real time environment in the calculation of the position and angular orientation of the centroid of the payload platform when the magnitude of the actuator extensions is known. Sufficient accuracy is obtained by using only one Newton-Raphson iteration per integration step of the real time environment.

Dieudonne, J. E.↗
NASA NTRS1974

Laser-actuated mechanical device

Actuator is portable and can be used in high-temperature (over 500 C) environments by incorporating tungsten metal film and quartz window. Actuator can be triggered when it is not directly in laser beam path by utilizing fiber optics. It is advantageous for remotely switching ultra-high voltage systems.

Murphy, A. J.↗
NASA NTRS1973

High performing actuation system for use with a louver array for satellite thermal control

A high performing actuation system has been developed to drive one pair or a set of 9 pairs of louver blades. The system uses a Bourdon spiral as the driving member. The response time of the liquid expansion of the spiral system is in the order of three seconds. Besides performance tests, qualification tests have been carried out on a prototype system, demonstrating that the actuation system withstands normal launching conditions; projected operating life of 7 years with more than 7000 cycles can be expected.

Reusser, P. U.↗
NASA NTRS1973

Thermally oscillating actuators

The actuator was redesigned to accommodate the new thermal motor for the Helios flipper. This design retained the basic configuration and dimensions of the original actuator. Changes were made primarily to the cradle and motor assembly. Because of the increased dimensions of the thermal motor, it was necessary to increase the diameter of the pellet case and associated parts including the back off spring and the piston return spring. The new springs were designed to yield the same spring rate differential as the originals. The design effort resulted in a new top assembly and approximately twenty sub-assembly and detail drawings. A list of drawings generated by EMR is attached.

Source record↗
NASA NTRS1974

Manual actuator

An actuator for an exercising machine employable by a crewman aboard a manned spacecraft is presented. The actuator is characterized by a force delivery arm projected from a rotary imput shaft of an exercising machine and having a force input handle extended orthogonally from its distal end. The handle includes a hand-grip configured to be received within the palm of the crewman's hand and a grid pivotally supported for angular displacement between a first position, wherein the grid is disposed in an overlying juxtaposition with the hand-grip, and a second position, angularly displaced from the first position, for affording access to the hand-grip, and a latching mechanism fixed to the sole of a shoe worn by the crewman for latching the shoe to the grid when the grid is in the first position.

Gause, R. L.↗
NASA NTRS1974

Optically actuated two position mechanical mover

An optically actuated mechanical mover adapted to be moved from an ambient position to an active position, is disclosed. The mechanical mover essentially comprises a piston/cylinder arrangement including a piston that is contained within an internal cylindrical chamber of a housing. The cylindrical chamber is configured to permit the piston to be moved for the length of the chamber as a work stroke. A lock pin extending through the piston, and diametrically opposed walls of the chamber housing, retain the piston in the ambient position at one end of the chamber. An actuator for producing a pressure or shock wave that drives the piston is positioned at the end of the chamber corresponding to the piston ambient position.

Yang, L. C.↗
NASA NTRS1973

Actuator digital interface unit (AIU)

Alternate versions of the actuator interface unit are presented. One alternate is a dual-failure immune configuration which feeds a look-and-switch dual-failure immune hydraulic system. The other alternate is a single-failure immune configuration which feeds a majority voting hydraulic system. Both systems communicate with the data bus through data terminals dedicated to each user subsystem. Both operational control data and configuration control information are processed in and out of the subsystem via the data terminal which yields the actuator interface subsystem, self-managing within its failure immunity capability.

Source record↗
NASA NTRS1974

Digital flight control actuation system study

Flight control actuators and feedback sensors suitable for use in a redundant digital flight control system were examined. The most appropriate design approach for an advanced digital flight control actuation system for development and use in a fly-by-wire system was selected. The concept which was selected consisted of a PM torque motor direct drive. The selected system is compatible with concurrent and independent development efforts on the computer system and the control law mechanizations.

Rossing, R.↗
NASA NTRS1974

Asymmetrical booster guidance and control system design study. Volume 3: Space shuttle vehicle SRB actuator failure study

The investigation of single actuator failures on the space shuttle solid rocket booster required the analysis of both square pattern and diamond pattern actuator configurations. It was determined that for failures occuring near or prior to the region of maximum dynamic pressure, control gain adjustments can be used to achieve virtually nominal mid-boost vehicle behavior. A distinct worst case failure condition was established near staging that could significantly delay staging. It is recommended that the square pattern be retained as a viable alternative to the baseline diamond pattern because the staging transient is better controlled resulting in earlier staging.

Williams, F. E.↗
NASA NTRS1975

Reducing flow requirements of fluid actuators

Method reduces volumetric rate of hydraulic fluid or air to drive actuator at high speed. Method can be used with any positive displacement actuator with multiple chambers.

Long, M. J.↗
NASA NTRS1975

Redundant actuator development program

Two concepts of redundant secondary actuator mechanization, applicable to future advanced flight control systems, were studied to quantitatively assess their design applicability to an AST. The two actuator concepts, a four-channel, force summed system and a three-channel, active/standby system have been developed and evaluated through analysis, analog computer simulation, and piloted motion simulation. The quantitative comparison of the two concepts indicates that the force summed concept better meet performance requirements, although the active/standby is superior in other respects. Both concepts are viable candidates for advanced control application dependent on the specific performance requirements.

Chenoweth, C. C.↗