Search NASA⌕ Search

SEARCH · Search NASA

Results for “aircraft engine simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Noise Benefits of Increased Fan Bypass Nozzle Area

An advanced model turbofan (typical of current engine technology) was tested in the NASA Glenn 9 by 15 Foot Low Speed Wind Tunnel (9-by 15-Foot LSWT) to explore far field acoustic effects of increased bypass nozzle area. This fan stage test was part of the NASA Glenn Fan Broadband Source Diagnostic Test, second entry (SDT2) which acquired aeroacoustic results over a range of test conditions. The baseline nozzle was sized to produce maximum stage performance for the engine at a high altitude, cruise point condition. However, the wind tunnel testing is conducted near sea level conditions. Therefore, in order to simulate and obtain performance at other aircraft operating conditions, two additional nozzles were designed and tested-one with a +5 percent increase in weight flow (+5.4 percent increase in nozzle area compared with the baseline nozzle), sized to simulate the performance at the stage design point conditions, and the other with a +7.5 percent increase in weight flow (+10.9 percent increase in nozzle area), sized for maximum weight flow with a fixed nozzle at sea level conditions. Measured acoustic benefits with increased nozzle area were very encouraging, showing overall sound power level (OAPWL) reductions of 2 or more dB while the stage thrust actually increased by several percentage points except fro the most open nozzle at takeoff rotor speed where stage performance decreased. These noise reduction benefits were seen to primarily affect broadband noise, and were evident throughout the range of measured sideline angles.

Woodward, Richard P.↗
NASA NTRS2014

Learning the Task Management Space of an Aircraft Approach Model

Validating models of airspace operations is a particular challenge. These models are often aimed at finding and exploring safety violations, and aim to be accurate representations of real-world behavior. However, the rules governing the behavior are quite complex: nonlinear physics, operational modes, human behavior, and stochastic environmental concerns all determine the responses of the system. In this paper, we present a study on aircraft runway approaches as modeled in Georgia Tech's Work Models that Compute (WMC) simulation. We use a new learner, Genetic-Active Learning for Search-Based Software Engineering (GALE) to discover the Pareto frontiers defined by cognitive structures. These cognitive structures organize the prioritization and assignment of tasks of each pilot during approaches. We discuss the benefits of our approach, and also discuss future work necessary to enable uncertainty quantification.

Validation↗
NASA NTRS1989

Integrated autopilot/autothrottle for the NASA TSRV B-737 aircraft: Design and verification by nonlinear simulation

An integrated autopilot/autothrottle was designed for flight test on the NASA TSRV B-737 aircraft. The system was designed using a total energy concept and is attended to achieve the following: (1) fuel efficiency by minimizing throttle activity; (2) low development and implementation costs by designing the control modes around a fixed inner loop design; and (3) maximum safety by preventing stall and engine overboost. The control law was designed initially using linear analysis; the system was developed using nonlinear simulations. All primary design requirements were satisfied.

Bruce, Kevin R.↗
NASA NTRS2007

Airframe Noise Results from the QTD II Flight Test Program

With continued growth in air travel, sensitivity to community noise intensifies and materializes in the form of increased monitoring, regulations, and restrictions. Accordingly, realization of quieter aircraft is imperative, albeit only achievable with reduction of both engine and airframe components of total aircraft noise. Model-scale airframe noise testing has aided in this pursuit; however, the results are somewhat limited due to lack of fidelity of model hardware, particularly in simulating full-scale landing gear. Moreover, simulation of true in-flight conditions is non-trivial if not infeasible. This paper reports on an investigation of full-scale landing gear noise measured as part of the 2005 Quiet Technology Demonstrator 2 (QTD2) flight test program. Conventional Boeing 777-300ER main landing gear were tested, along with two noise reduction concepts, namely a toboggan fairing and gear alignment with the local flow, both of which were down-selected from various other noise reduction devices evaluated in model-scale testing at Virginia Tech. The full-scale toboggan fairings were designed by Goodrich Aerostructures as add-on devices allowing for complete retraction of the main gear. The baseline-conventional gear, faired gear, and aligned gear were all evaluated with the high-lift system in the retracted position and deployed at various flap settings, all at engine idle power setting. Measurements were taken with flyover community noise microphones and a large aperture acoustic phased array, yielding far-field spectra, and localized sources (beamform maps). The results were utilized to evaluate qualitatively and quantitatively the merit of each noise reduction concept. Complete similarity between model-scale and full-scale noise reduction levels was not found and requires further investigation. Far-field spectra exhibited no noise reduction for both concepts across all angles and frequencies. Phased array beamform maps show inconclusive evidence of noise reduction at selective frequencies (1500 to 3000 Hz) but are otherwise in general agreement with the far-field spectra results (within measurement uncertainty).

Elkoby, Ronen↗
NASA NTRS1994

Numerical simulation of helicopter engine plume in forward flight

Flowfields around helicopters contain complex flow features such as large separated flow regions, vortices, shear layers, blown and suction surfaces and an inherently unsteady flow imposed by the rotor system. Another complicated feature of helicopters is their infrared signature. Typically, the aircraft's exhaust plume interacts with the rotor downwash, the fuselage's complicated flowfield, and the fuselage itself giving each aircraft a unique IR signature at given flight conditions. The goal of this project was to compute the flow about a realistic helicopter fuselage including the interaction of the engine air intakes and exhaust plume. The computations solve the Think-Layer Navier Stokes equations using overset type grids and in particular use the OVERFLOW code by Buning of NASA Ames. During this three month effort, an existing grid system of the Comanche Helicopter was to be modified to include the engine inlet and the hot engine exhaust. The engine exhaust was to be modeled as hot air exhaust. However, considerable changes in the fuselage geometry required a complete regriding of the surface and volume grids. The engine plume computations have been delayed to future efforts. The results of the current work consists of a complete regeneration of the surface and volume grids of the most recent Comanche fuselage along with a flowfield computation.

Dimanlig, Arsenio C. B.↗
NASA NTRS1999

Neural Network and Regression Approximations Used in Aircraft Design

NASA Lewis Research Center's CometBoards Test Bed was used to create regression and neural network models for a High-Speed Civil Transport (HSCT) aircraft. Both approximation models that replaced the actual analysis tool predicted the aircraft response in a trivial computational effort. The models allow engineers to quickly study the effects of design variables on constraint and objective values for a given aircraft configuration. For example, an engineer can change the engine size by 1000 pounds of thrust and quickly see how this change affects all the output values without rerunning the entire simulation. In addition, an engineer can change a constraint and use the approximation models to quickly reoptimize the configuration. Generating the neural network and the regression models is a time-consuming process, but this exercise has to be carried out only once. Furthermore, an automated process can reduce calculations substantially.

Patnaik, Surya N.↗
NASA NTRS2023

Flight Simulator Demonstration and Certification Implications of Powertrain Failure Mitigation in a Partial Turboelectric Aircraft

The Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC ABL) is a concept aircraft with a partial turboelectric powertrain. The complexity and integrated nature of the partial turboelectric powertrain architecture presents failure modes and hazards not found in conventional aircraft propulsion designs. Previously, various electrical and mechanical faults and associated recovery modes were demonstrated in a dynamic model of the powertrain. It was shown that certain faults were catastrophic without recovery logic, due specifically to the interaction of the subsystems. However, in each case, the logic, known as a reversionary control mode, enabled continued operation with assumed sufficient thrust to maintain safe flight. The current work evaluates the powertrain faults and recovery strategies using a full aircraft model in a piloted flight simulator, and places it in the context of current regulatory practice. Faults initiated in flight were successfully mitigated, with the accommodated aircraft subsequently evaluated against certification requirements for three-engine aircraft, which were shown to be appropriate for the STARC-ABL configuration.

certification↗
NASA NTRS1990

High speed turboprop aeroacoustic study (counterrotation). Volume 2: Computer programs

The isolated counterrotating high speed turboprop noise prediction program developed and funded by GE Aircraft Engines was compared with model data taken in the GE Aircraft Engines Cell 41 anechoic facility, the Boeing Transonic Wind Tunnel, and in the NASA-Lewis 8 x 6 and 9 x 15 wind tunnels. The predictions show good agreement with measured data under both low and high speed simulated flight conditions. The installation effect model developed for single rotation, high speed turboprops was extended to include counter rotation. The additional effect of mounting a pylon upstream of the forward rotor was included in the flow field modeling. A nontraditional mechanism concerning the acoustic radiation from a propeller at angle of attack was investigated. Predictions made using this approach show results that are in much closer agreement with measurement over a range of operating conditions than those obtained via traditional fluctuating force methods. The isolated rotors and installation effects models were combined into a single prediction program. The results were compared with data taken during the flight test of the B727/UDF (trademark) engine demonstrator aircraft.

Whitfield, C. E.↗
DOE OSTI2024

Autonomous Emergency Landing for Fixed-Wing Aircraft with Energy-Constrained Closed-Loop Prediction

Here this paper presents a new approach for autonomous motion planning for aircraft suffering from a loss-of-thrust emergency. Specifically, we show how modifications to the Closed-Loop Rapidly exploring Random Trees (CL-RRT) framework combined with controlled energy dissipation can enable rapid and effective kinodynamic motion planning. This CL-RRT Glide algorithm uses closed-loop prediction not only for node connections but also to estimate the remaining energy and prune infeasible paths. This greatly speeds up the search process, which is essential for emergency situations. In addition, we improve the ability of the gliding aircraft to reach a goal position and energy state. We do so by creating a Dissipative Total Energy Control Scheme (TECS). Dissipative TECS enables the glider to lose excess altitude in order to reach a desired energy level. Simulation results illustrate how the proposed methods enable faster motion planning. We also integrate the system into a small unmanned aerial vehicle system and experimentally demonstrate autonomous glide planning and execution during a motor-failure event. This type of algorithm can primarily benefit unmanned aircraft but can also serve to assist pilots in stressful emergency situations.

42 ENGINEERING↗
NASA NTRS2023

Real-Time Hardware-in-the-Loop Evaluation of A Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-theloop (HIL) testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially HIL, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the HIL test are presented and shown to be in good agreement with pretest simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRS1996

Fuzzy Logic Decoupled Longitudinal Control for General Aviation Airplanes

It has been hypothesized that a human pilot uses the same set of generic skills to control a wide variety of aircraft. If this is true, then it should be possible to construct an electronic controller which embodies this generic skill set such that it can successfully control difference airplanes without being matched to a specific airplane. In an attempt to create such a system, a fuzzy logic controller was devised to control throttle position and another to control elevator position. These two controllers were used to control flight path angle and airspeed for both a piston powered single engine airplane simulation and a business jet simulation. Overspeed protection and stall protection were incorporated in the form of expert systems supervisors. It was found that by using the artificial intelligence techniques of fuzzy logic and expert systems, a generic longitudinal controller could be successfully used on two general aviation aircraft types that have very difference characteristics. These controllers worked for both airplanes over their entire flight envelopes including configuration changes. The controllers for both airplanes were identical except for airplane specific limits (maximum allowable airspeed, throttle lever travel, etc.). The controllers also handled configuration changes without mode switching or knowledge of the current configuration. This research validated the fact that the same fuzzy logic based controller can control two very different general aviation airplanes. It also developed the basic controller architecture and specific control parameters required for such a general controller.

Duerksen, Noel↗
NASA NTRS1957

Interference Effects of Fuselage-Stored Missiles on Inlet Duct Model of an Interceptor-Type Aircraft at Mach Numbers 1.5 to 1.9

The effect of missile armament on the performance of an interceptor-type aircraft model has been determined at Mach numbers 1.5, 1.7, and 1.9 and at angles of attack to 19 deg. With this configuration missiles were carried in a bay located on the bottom of the aircraft fuselage and mounted to a rotatable missile door. Rotation of the door then brought the missiles into the external or firing position. The aircraft model was characterized by triangular-shaped normal-shock inlets located at the wing roots. Relatively short and curved subsonic diffusers fed simulated twin side-by-side turbojet engines. Inasmuch as the missile bay extended considerably ahead of the inlet station, rotation of the missile door created considerable disturbance of the flow entering the inlets. In comparison with the internal missile arrangement, the external missile configurations increased the model lift, drag, and pitching moment. While the diffuser-exit flow distortion and static-pressure fluctuations were not greatly affected, diffuser total-pressure recovery was reduced as much as 0.058 at Mach number 1.9 for one missile configuration. The most detrimental effect of missile-door rotation occurred at the transient door positions, or with the door halfwzy between the missiles-in and -out conditions. At this door position the flow into the inlets was highly asymmetrical. Although the performance of both left and right ducts was generally reduced, the inlet duct on the cavity side of the missile door was most severely penalized, becoming unstable recovery losses and increases in flow distortion. The installation of fuselage fences along the missile bay was only partially effective in reducing these losses.

Piercy, T. G.↗
NASA NTRS1975

NASA/Army XV-15 tilt rotor research aircraft familiarization document

The design features and general characteristics of the NASA/Army XV-15 tilt rotor research aircraft are described. This aircraft was conceived as a proof-of-concept vehicle and a V/STOL research tool for integrated wind tunnel, flight-simulation, and flight-test investigations. Discussions of special design provisions and safety considerations necessary to perform these missions are included in this report. In addition to predictions of aircraft and engine performance for the hover, helicopter, and airplane flight modes, analytical estimates of the structural and dynamic limitations of the XV-15 are provided.

Source record↗
NASA NTRS1977

Simulator evaluation of optimal thrust management/fuel conservation strategies for airbus aircraft on short haul routes

The feasibility of incorporating optimal concepts into a practical system was determined. Various earlier theoretical analyses were confirmed, and insight was gained into the sensitivity of fuel conservation strategies to nonlinear and second order aerodynamic and engine characteristics. In addition to the investigation of optimal trajectories the study ascertained combined fuel savings by utilizing various procedure-oriented improvements such as delayed flap/decelerating approaches and great circle navigation.

Bochem, J. H.↗
NASA NTRS1977

Space Shuttle Program Progress Report

A status report is presented on progress in the design, manufacturing and testing of components of the space transportation system (STS), and primarily the Space Shuttle vehicles. Project landmarks from 1969 to 1981 are indicated, fabrication of the Shuttle Orbiter and rollout of the first prototype are described, fabrication and assembly of some Orbiter parts are sketched, and some of the subsystems (thermal protection, avionics, maneuvering aids, reaction control, remote manipulator) are described. Also discussed are: Orbiter carrier aircraft, Shuttle main engine and tests, external fuel tank, solid rocket booster, launch and landing facilities. A separate section is devoted to ground tests (vibration, propulsion, electronics, avionics integration), trainers and simulators, and flight tests (captive flight, free flight, landing and approach, orbital flight).

Thompson, R. F.↗
NASA NTRS1978

Temperature distributions and thermal stresses in a graded zirconia/metal gas path seal system for aircraft gas turbine engines

A ceramic/metallic aircraft gas turbine outer gas path seal designed for improved engine performance was studied. Transient temperature and stress profiles in a test seal geometry were determined by numerical analysis. During a simulated engine deceleration cycle from sea-level takeoff to idle conditions, the maximum seal temperature occurred below the seal surface, therefore the top layer of the seal was probably subjected to tensile stresses exceeding the modulus of rupture. In the stress analysis both two- and three-dimensional finite element computer programs were used. Predicted trends of the simpler and more easily usable two-dimensional element programs were borne out by the three-dimensional finite element program results.

Taylor, C. M.↗
NASA NTRS1978

Propulsion systems noise technology

Turbofan engine noise research relevant to conventional aircraft is discussed. In the area of fan noise, static to flight noise differences were discussed and data were presented for two different ways of simulating flight behavior. Experimental results from a swept rotor fan design are presented which show that this concept has potential for reducing the multiple-pure-tone or buzz-saw noise related to the shock waves on a fan operating at supersonic tip speeds. Acoustic suppressor research objectives centered around the effect of the wave system generated by the fan stage that is the input to the treatment. A simplifying and unifying parameter, mode cutoff ratio was described. Results are presented which show that suppressor performance can be improved if the input wave is more precisely described. In jet noise, calculated results showing the potential noise reduction from the use of internal mixer nozzles rather than separate flow nozzles are presented.

Feiler, C. E.↗
NASA NTRS1988

Scale model acoustic testing of counterrotating fans

The UDF contrarotating propfan has been subjected to scale model wind tunnel testing to ascertain both general performance and acoustic characteristics data bases. Model Propulsion Simulator test rigs able to mount contrarotating fan blades of up to 24.5-inch diameter were used, and one of these was installed in a large anechoic test chamber for acoustic measurement of conditions simulating representative takeoffs, power cutbacks, and landing approaches. Attention is presently given to the data acquisition/reduction systems, the scaling criteria used to obtain engine size acoustic data, and comparisons with demonstrator aircraft in-flight acoustic test results.

Janardan, B. A.↗