Search NASA⌕ Search

SEARCH · Search NASA

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Secondary creep behavior of Zr-4 claddings under LOCA conditions

The thermo-mechanical behavior of Zircaloy-4 fuel rods under Loss-Of-Coolant Accident (LOCA) conditions in water cooled reactors is investigated. A custom experimental setup is dedicated to the high-temperature creep ballooning study of 90 mm long cladding samples. Creep tests were performed under an inert environment (argon), for temperatures from 750 to 850 C. degrees and internal pressures ranging from 1 to 5 MPa. During its operating life, Zr-4 cladding is submitted to oxidation and hydriding. These parameters strongly influence the creep behavior of Zirconium alloys at high temperatures. A first campaign on as-received Zr-4 was performed. Creep-rates are computed using 2-Dimensional Digital Image Correlation (2D-DIC) and are correlated to local temperatures measured using Near Infra-Red thermography. As-received Zr-4 behavior laws are determined using Finite Element Model Updating (FEMU). Norton exponents and activation energies are determined for thermal-mechanical conditions of the performed tests. The results show that the effect of applied stress on the Norton exponent is evidenced in the study for both α-phase and (α + β)-phase domains. The determined stress exponent magnitudes are very consistent with literature data depending on the thermomechanical test conditions. The activation energy parameter is very sensitive to the thermo-mechanical conditions and remains valid within a limited temperature and stress ranges to the authors' knowledge. The beginning of the (α + β)-phase domain is clearly identified with the activation energy increase. Finally, steady-state creep is accurately modeled depending on ballooning thermo-mechanical conditions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Radiation tolerant joining for silicon carbide-based accident tolerant fuel cladding

Silicon carbide (SiC) and silicon carbide fiber reinforced, silicon carbide matrix (SiC-SiC) composites are candidate materials for nuclear fuel cladding in accident tolerant light water reactors and advanced high temperature reactors due to their chemical stability and retention of strength at elevated temperature and neutron flux. A reliable means to join silicon carbide components is imperative to the successful implementation of SiC-based structural nuclear materials as fuel cladding as well as more complex core internal structures. A comprehensive approach has been taken to address several of the significant challenges associated with SiC joining and fabrication of complex SiC structures. This work focuses on low activation joining materials that are expected to behave well under a variety of different reactor operating conditions. Pre- and post-irradiation mechanical testing and microstructural evaluation will be presented for specimens subjected to fast flux irradiation to 4.5 dpa at 730 C. degrees, as well as 8.7 dpa at 270 C. degrees. Joints did not exhibit any strength degradation under either irradiation condition. Additionally, the performance of joined cylindrical SiC-SiC composite specimens was evaluated following irradiation in pressurized water reactor (PWR) coolant chemistry to 0.5 dpa. Lastly, out-of-pile characterization of permeability has been conducted on joined cylindrical SiC-SiC specimens to assess performance of this joint material under additional conditions relevant to reactor operation. Details of the experimental set-up and relationships between microstructure and performance will be discussed. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of joining technology using local heating for SiC fuel cladding

Silicon carbide (SiC) is an attractive material for an accident-tolerant fuel in light water reactors because of its lower hydrogen-generation rate and lower heat of reaction than conventional Zircaloy. On the other hand, practical application of SiC fuel cladding faces a lot of critical issues, one of which is end-plug joining. The objective of this study is to clarify the feasibility of end-plug joining by silicon brazing using local heating by evaluating the shear strength of joint specimens and producing a circumferential joint experimentally. Silicon is thought to be a compatible joining material with SiC because as well as being a constituent of SiC, its thermal-expansion coefficient is close to that of SiC. Local heating using processes such as laser irradiation and a resistance-heating element needs to be applied for end-plug joining. Brazing is expected to seal a cladding with an end plug by using brief heating without a strong compression force. Shear strength was evaluated using specimens with silicon-brazing joints processed using laser irradiation. The joint sections without defects showed shear strengths higher than or equal to 59 MPa at temperatures from normal room temperature to 1473 K. The average shear strength of the joint (99 MPa) is comparable to that of a diffusion-bonding joint using titanium or molybdenum foil. A tube and a plug were circumferentially joined with silicon brazing using laser irradiation or a graphite heating element. A defocused laser beam was effective for joining without cracking during laser irradiation. Although local heating using a resistance-heating element can more easily control the temperature of the joint, it took longer processing time than that using laser irradiation due to limited temperature-increase rate in order to avoid thermal shock damage. (authors)

36 MATERIALS SCIENCE↗

Irradiation - High heat flux synergism in silicon carbide-based fuel claddings for light water reactors

Silicon carbide-based fuel cladding for light water reactors is anticipated to develop a unique stress state as a combined result from the high radial heat flux and irradiation-induced swelling assisted by thermal conductivity decrease. In order to verify the multi-physics finite-element analysis of this unique stress state, a novel experiment capturing the synergism of a high radiation field and a high radial heat flux in tubular silicon carbide specimens had been designed and implemented in the High Flux Isotope Reactor, Oak Ridge National Laboratory. In this experiment, small diameter tube test specimens made of monolithic or composite silicon carbide were irradiated to a dose of ∼2x10{sup 25} n/m{sup 2} (E > 0.1 MeV) under a radial heat flux of ∼0.6 MW/m{sup 2} while the outer surface temperature was maintained at a target temperature of about 300 Celsius degrees achieving a steep temperature gradient through the cladding wall thickness. The primary objective of the present paper is to discuss the technical planning and execution of the experiment. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Study on the Temperature Correlation between a Surface of Dry Storage Canister and Spent Fuel Clad - 16446

Analysis of temperature correlation between dry canister surface and spent fuel cladding is performed in this study. The result shows that the spent fuel cladding temperature is possibly estimated using canister surface temperature in normal condition and the result of estimation is depended on analysis model. Two analysis models are designed by using a hypothetical spent fuel model and thermal analysis for the models is performed by using CFX(v11.0) code. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of Alloying Additions on Wrought FeCrAl Alloys for Accident-Tolerant Fuel Cladding

Nuclear-grade wrought Fe-Cr-Al alloys are under development as one of the candidate materials for accident-tolerant fuel (ATF) cladding for light water reactors (LWRs) because of their superior oxidation and corrosion resistance in high-temperature steam environment compared to Zr-based alloys that are currently in service. Numerous efforts have been made for the development of the FeCrAl alloys with the ATF concept. The current researches focused on optimizing the balance between the improved environmental compatibility and sufficient mechanical properties in both normal service condition and under accident scenario, as well as fabricability of seamless tube product for fuel cladding applications. Alloying addition is one of the key factors to control the various properties. The effect of Cr and Al additions on the properties in model Fe-Cr-Al-Y alloys were systematically examined by the authors, and the candidate base alloy composition with 13 wt.% Cr and 5 wt.% Al was proposed for further development. The modified FeCrAl alloys with Mo and Nb additions were also investigated in order to achieve improved strength. It was revealed that the microstructure control together with the thermal stability to retain desired microstructure were also the dominant factors for successful development of ATF FeCrAl alloys, especially when the fabricability of seamless tube production was also considered. This paper summarizes further investigation of alloying effects with a wide composition range of Cr and Al additions in the model alloys, as well as the effect of minor alloying additions of Mo, Nb, and Zr, through evaluation of the tensile properties. The combined effect of microstructure control is also discussed. Effect of alloying additions on tensile properties of wrought FeCrAl alloys was investigated. Minor alloying additions such as Al, Mo, Nb, and Zr were found to improve room-temperature tensile strength of the wrought FeCrAl alloys significantly. It was also found that stabilized deformed microstructure consisting of subgrains was also effective to improve the properties compared to the recrystallized grain structure. Optimization to balance the properties and the seamless FeCrAl tube fabricability is currently in progress. (authors)

36 MATERIALS SCIENCE↗

Pool Boiling CHF Experiment for Cr-alloy-coated Accident Tolerant Fuel Cladding

The severe accident at the Fukushima nuclear power plants forced the nuclear communities to revise and reinforce their safety technology, especially accident tolerance. The main problem of Zr-based alloys is hydrogen generation owing to steam oxidation in a very high temperature environment. Currently, several types of Accident Tolerant Fuel (ATF) claddings that eliminate the steam oxidation problem have been presented as alternatives. Although the ATFs have shown appropriate performances in terms of material engineering, thorough tests including thermal hydraulic concerns are still required to ensure the design compatibilities. In this study, we conducted pool boiling critical heat flux (CHF) experiments using Cr-alloy-coated ATF claddings to verify basic thermal hydraulic performances. (authors)

36 MATERIALS SCIENCE↗

Modeling Radiolysis and Chemical Reactions during Dry Storage of Aluminum-clad Spent Nuclear Fuel

After aluminum-clad spent nuclear fuel (ASNF) is removed from the reactor, it is initially stored in spent fuel pools, which are specially designed water-filled basins that provide temporary cooling to reduce the temperature of the fuel assemblies and provide radiation shielding. ASNF continues to generate heat due to the radioactive decay of elements within the fuel, which persists for many years post-shutdown as the residual radioactive products decay into more stable elements. During the wet storage period, an oxyhydroxide layer composed of boehmite/bayerite forms on the surfaces of the aluminum cladding from exposure to water in the pools. Road-ready packaging for long-term disposition of the ASNF involves dry storage in helium backfilled DOE standard canisters (DSCs). When the ASNF is removed from water storage and dried, most of the water is removed, but some physisorbed and chemisorbed water remains in the oxyhydroxide layers. This residual water can produce hydrogen when exposed to radiation from the ASNF during dry storage. Predicting hydrogen accumulation over time in the DSCs is critical for long-term storage considerations. Previous modeling efforts have developed coupled computational fluid dynamics (CFD)-chemical models to simulate temperature, pressure, and gas phase concentrations within the DSCs. These models use the thermal field predicted by CFD as input to a radiolysis model for the gas phase and the surface oxyhydroxide layer chemistry. Given the long storage period of the DSCs and the impracticality of long-term experiments, a simulation-based approach is necessary to assess chemical evolution within the canisters. This study advances the development of a modeling framework designed to simulate the chemical evolution of spent fuel canisters. Both thermal and radiation-driven reactions are considered, with radiation kinetics quantified using G-values. Sensitivity analysis identifies key parameters influencing species composition. Reaction pathway diagrams offer insight into dominant species formation routes, enabling more effective comparisons between model predictions and experimental observations, particularly regarding the production of hydrogen. Results show that the model predicts significant hydrogen gas production with minimal oxygen generation, primarily due to hydrogen formation via boehmite pathways. These findings underscore the importance of accurately characterizing surface-bound species and radiolysis kinetics. A deeper understanding of these mechanisms is critical for evaluating the long-term safety of nuclear waste storage.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗

Preliminary characterization and projections of PVD coatings on SiC cladding for Light Water Reactors

Physical Vapor Deposition (PVD) based CrN, Cr and TiN are currently the leading mitigation coatings for SiC-based Light Water Reactor (LWR) fuel cladding. This manuscript describes the morphology, phase analysis and elemental composition of coatings deposited by commercial vendors on SiC clad materials. The coatings showed continuous crack-free morphology with few microstructural flaws. X-ray analysis and spectroscopy indicated high purity >99.9%. Mechanical tests of coating debonding (by ASTM D4541) and scratch-indentation (by ASTM E2546) were conducted. Strong interface bonding was observed and higher resistance to normal and shear stresses was observed from thicker coatings. Preliminary developments in scratch testing, phase analysis, future needs and expected behavior under irradiation are discussed.

Ang, Caen K.↗

Oxidation of Fuel Cladding Candidate Materials in Steam Environments at High Temperature and Pressure

Under certain severe accident conditions, the fuel rods of nuclear power plants are exposed to high temperature/pressure steam environments in which the Zr alloy cladding is rapidly oxidized. As alternative claddings, the oxidation resistances of SiC-based materials and stainless steels with high Cr and/or Al additions have been examined from 800-1200 C in high-pressure steam environments. Very low reaction kinetics were observed with alumina-forming FeCrAl alloys at 1200 C while Fe-Cr alloys with only 15-20% Cr were rapidly attacked.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High-temperature oxidation kinetics of sponge-based E110 cladding alloy

Two-sided oxidation experiments were recently conducted at 900°C–1200 °C in flowing steam with samples of sponge-based Zr-1Nb alloy E110. Although the old electrolytic E110 tubing exhibited a high degree of susceptibility to nodular corrosion and experienced breakaway oxidation rates in a relatively short time, the new sponge-based E110 demonstrated steam oxidation behavior comparable to Zircaloy-4. Sample weight gain and oxide layer thickness measurements were performed on oxidized E110 specimens and compared to oxygen pickup and oxide layer thickness calculations using the Cathcart-Pawel correlation. Our study shows that the sponge-based E110 follows the parabolic law at temperatures above 1015 °C. At or below 1015 °C, the oxidation rate was very low when compared to Zircaloy-4 and can be represented by a cubic expression. No breakaway oxidation was observed at 1000 °C for oxidation times up to 10,000 s. Arrhenius expressions are given to describe the parabolic rate constants at temperatures above 1015 °C and cubic rate constants are provided for temperatures below 1015 °C. The weight gains calculated by our equations are in excellent agreement with the measured sample weight gains at all test temperatures. In addition to the as-fabricated E110 cladding sample, prehydrided E110 cladding with hydrogen concentrations in the 100–150 wppm range was also investigated. The effect of hydrogen content on sponge-based E110 oxidation kinetics was minimal. No significant difference was found between as-fabricated and hydrided samples with regard to oxygen pickup and oxide layer thickness for hydrogen contents below 150 wppm.

36 MATERIALS SCIENCE↗

Hydrothermal corrosion of 2nd generation FeCrAl alloys for accident tolerant fuel cladding

As part of an effort to develop advanced fuel cladding for use in light water reactors, several FeCrAl alloys have been developed at Oak Ridge National Laboratory. A second generation of these alloys bearing additional alloying elements over the previously tested model alloys were tested in boiling water reactor (BWR) conditions to determine their resistance to hydrothermal corrosion. Coupons with alloy compositions Fe–10Cr–6Al–2Mo, Fe–13Cr–5Al–2Mo, Fe–13Cr–6Al–2Mo, Fe–13Cr–7Al–2Mo, and Fe–13Cr–5Al–2Mo–1Nb were tested in normal water chemistry (NWC) and hydrogen water chemistry (HWC) for 9 months in continuously refreshing autoclaves. Commercial FeCrAl alloy APMT and Zircaloy-2 were also tested for comparison. Among samples exposed to HWC, Fe–13Cr–7Al–2Mo performed worst with an average mass loss of 1.3 mg/cm2 over 9 months. This mass loss represents an estimated thickness loss of approximately 60 μm over 6 years. Samples exposed to NWC had very small mass losses of less than 0.15 mg/cm2 or mass gains up to 0.05 mg/cm2. Based on the results of this testing, the 2nd generation FeCrAl alloys tested exhibit low wall thickness loss and are suitable in terms of corrosion resistance for use as LWR cladding in BWR-HWC and BWR-NWC under normal operating conditions.

Raiman, Stephen↗

Hydrogen effects on thermal diffusivity and electrical resistivity of zircaloy cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. Here, in this work, we first used laser flash analysis method and four-probe configuration method to measure the thermal diffusivity and electrical resistivity of Zircaloy tubes respectively, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the laser flash analysis setup and four-probe configuration method for investigating thermal diffusivity and electrical resistivity of Zircaloy tubes. We further investigated the hydrogen effect on thermal diffusivity and electrical resistivity of Zircaloy. Hydrogen plays significant roles in the thermal diffusivity of Zircaloy, which depends on the hydrogen concentration. For higher hydrogen contents (1130 and 1820 wppm in this work), where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature at the α-Zr + δ-hydride phase regime, while increase at higher temperature at the α-Zr + β-Zr phase regime. For low hydrogen concentration, where hydride dissolved into α-Zr matrix phase at higher temperature, the thermal diffusivity is lower than non-hydrided Zircaloy-4 with similar temperature-dependent trends. Such observation demonstrates the hydrogen effects on reducing thermal diffusivity of α-Zr phase. Hydrogen increases the electrical resistivity of Zircaloy. Similar to thermal diffusivity results, the phase transformation causes a reversal of temperature-dependent trends in electrical resistivity results in Zircaloy-4 with higher hydrogen contents.

36 MATERIALS SCIENCE↗

Dynamic data-driven multiscale modeling for predicting the degradation of a 316L stainless steel nuclear cladding material

Here, we have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗

FRAPCON analysis of cladding performance during dry storage operations

There is an increasing need in the U.S. and around the world to move used nuclear fuel from wet storage in fuel pools to dry storage in casks stored at independent spent fuel storage installations (ISFSI) or interim storage sites. The NRC limits cladding temperature to 400°C while maintaining cladding hoop stress below 90 MPa in an effort to avoid radial hydride reorientation. An analysis was conducted with FRAPCON-4.0 on three modern fuel designs with three representative used nuclear fuel storage temperature profiles that peaked at 400 °C. Results were representative of the majority of U.S. LWR fuel. They conservatively showed that hoop stress remains below 90 MPa at the licensing temperature limit. Results also show that the limiting case for hoop stress may not be at the highest rod internal pressure in all cases but will be related to the axial temperature and oxidation profiles of the rods at the end of life and in storage.

Dry Storage↗

Finite element simulation of gap opening between cladding tube and spacer grid in a fuel rod assembly using crystallographic models of irradiation growth and creep

A physically-based crystal plasticity framework for modeling irradiation growth and creep is interfaced with the finite element code ABAQUS in order to study the contact forces and the gap evolution between the spacer grid and the cladding tube as a function of irradiation in a representative section of a fuel rod assembly. Deformation mechanisms governing the gap opening are identified and correlated to the texture-dependent material response. Thus, in the absence of coolant flow-induced vibrations, these simulations predict the contribution of irradiation growth and creep to the gap opening between the cladding tube and the springs and dimples on the spacer grid. The simulated contact forces on the springs and dimples are compared to available experimental and modeling data. Various combinations of external loads are applied on the springs and dimples to simulate fuel rods in the interior and at the periphery of the fuel rod assembly. Furthermore, we found that loading conditions representative (to a first order approximation) of fuel rods at the periphery show higher gap opening. This is in agreement with in-reactor data, where rod leakages due to the synergistic effects of gap opening and coolant flow-induced vibrations were generally found to occur at the periphery of the fuel rod assembly.

36 MATERIALS SCIENCE↗

Sensitivity study of coupled chemical-CFD simulations for analyzing aluminum-clad spent nuclear fuel storage in sealed canisters

We report the United States Department of Energy (DOE) manages over 50 Metric Tons Heavy Metal (MTHM) of aluminum-clad spent nuclear fuel. One main source for DOE’s Aluminum-clad spent nuclear fuel (ASNF) inventory is the advanced test reactor (ATR) at the INL site, which makes this fuel of particular interest for storage scenarios. Road-ready and final disposition packaging configurations for the ATR fuel dictates storage within helium-backfilled, sealed DOE standard canisters. The conditions within these sealed canisters for extended (greater than50 year dry) storage is of interest. To further this goal, a three-dimensional (3D) multi-physics computational fluid dynamics (CFD) model is developed of the sealed DOE standard canisters. This 3D CFD model is one-way coupled with bulk gas radiolysis reactions considering sealed canisters with inert gas and possible trace amounts of air and water vapor. This study looks at the evolution of the thermal history of the canisters over a 50 year time period with a coupling to the chemical reactions occurring from radiolytic breakdown of residual water. A sensitivity study is then carried out over the parameters of the model including the fuel decay heat, residual water content, sealed pressure, canister external temperature, and canister emissivity. In pure helium, hydrogen generation rates are low, under 10 ppm, but hydrogen generation rates are affected greatly by the presence of even 1% residual air, increasing by 50-plus-fold, and nitric acid generation with residual air also occurs ranging from 500 to 4000 ppm after 50 years. The fuel decay heat and the residual water content show the most importance in the generation of hydrogen gas in pure air, and for nitric acid with a residual air condition. External temperature, canister emissivity and sealed pressure all show minor sensitivity effects to the generation of potentially harmful species.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗