Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation loops”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

519 records · Page 29

Low leakage current in heteroepitaxial Al 0.7 Sc 0.3 N ferroelectric films on Ga N

Wurtzite ( Al , Sc ) N ferroelectrics are attractive for microelectronics applications due to their chemical and structural compatibility with wurtzite semiconductors, such as Ga N and ( Al , Ga ) N . However, the leakage current in epitaxial stacks reported to date should be reduced for reliable device operation. Here, we demonstrate low leakage current in epitaxial Al 0.7 Sc 0.3 N films on Ga N with well-saturated ferroelectric hysteresis loops that are orders of magnitude lower (i.e., 0.07 A cm − 2 ) than previously reported films (1–19 A cm − 2 ) having similar or better structural characteristics. We also show that, for these high-quality epitaxial ( Al , Sc ) N films, structural quality (edge and screw dislocations), as measured by diffraction techniques, is not the dominant contributor to leakage. Instead, the small leakage in our films is limited by thermionic emission across the interfaces, which is distinct from the large leakage due to trap-mediated bulk transport in the previously reported ( Al , Sc ) N films. To support this conclusion, we show that Al 0.7 Sc 0.3 N on lattice-matched In 0.18 Ga 0.82 N buffers with improved structural characteristics but higher interface roughness exhibit increased leakage characteristics. This demonstration of low leakage current in heteroepitaxial ( Al , Sc ) N films and understanding of the importance of interface barrier and surface roughness can guide further efforts toward improving the reliability of wurtzite ferroelectric devices. Published by the American Physical Society 2025

36 MATERIALS SCIENCE↗

Effects of Fast Neutron Irradiation on Zirconium Carbide

High-purity zone refined zirconium carbide has been fast neutron irradiated in the dose and temperature range of 1-10 x 10{sup 25} N/m{sup 2} (E > 0.1 MeV) and 635-1480 C, respectively. Non-irradiated and as-irradiated properties were measured including the lattice parameter, hardness and elastic modulus as determined through nano-indentation, thermal conductivity, and indentation fracture toughness. The effects of neutron irradiation on the microstructure were also determined though using transmission electron microscopy. The general finding of this paper, limited to this particular zone refined ZrC of nominal C/Zr ratio of 0.93, is that this ceramic is quite stable under neutron irradiation in the temperature and dose range studied. Measurement of lattice parameter before and after irradiation indicated a lack of significant crystalline strain due to irradiation. Only modest changes were observed in the mechanical properties of hardness, elastic modulus, and indentation fracture toughness. The thermal conductivity underwent a slight reduction near 1000 C irradiation, though was essentially unchanged for 1300-1480 C irradiation. Transmission electron microscopy revealed black-spot-type defects (likely Frank or other small loops) for irradiation at 670 C, maturing to faulted Frank loops at 1280 C. As the irradiation temperature increased from 1280 C to the highest irradiation temperature, of 1496 C, a transition to prismatic loops occurs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Elimination of trench defects and V-pits from InGaN/GaN structures

The microstructural evolution of InGaN/GaN multiple quantum wells grown by metalorganic chemical vapor phase epitaxy was studied as a function of the growth temperature of the GaN quantum barriers (QBs). We observed the formation of basal stacking faults (BSFs) in GaN QBs grown at low temperature. The presence of BSFs terminated by stacking mismatch boundaries (SMBs) leads to the opening of the structure at the surface into a V-shaped trench loop. This trench may form above an SMB, thereby terminating the BSF, or above a junction between the SMB and a subsequent BSF. Fewer BSFs and thus fewer trench defects were observed in GaN QBs grown at temperatures higher than 830 °C. Further increase in the growth temperature of the GaN QBs led to the suppression of the threading dislocation opening into V-pits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Plastic Deformation on Passivation Characteristics of Type 304 Stainless Steel

Electrochemical response of Type 304 stainless steel, with different levels of plastic deformation, was investigated in solutions containing different amounts of H{sub 2}SO{sub 4} and KSCN at room temperature. Potentiodynamic polarization and double-loop electrochemical potentiokinetic reactivation (DL-EPR) techniques were used to characterize different levels of plastic deformation. The results have indicated that DL-EPR values and passivation current density increased with increase in plastic deformation. The DL-EPR values were correlated well with hardness and fraction of strain-induced martensite. Attack during DL-EPR tests occurred on strain regions within the matrix such as dislocations in austenite and martensite and/or interface between austenite and martensite. No well-defined correlation was observed between the levels of plastic deformation and potentiodynamic polarization behavior.

36 MATERIALS SCIENCE↗

Multiscale Model for Simulating Fission-Induced Recrystallization in U-Mo Alloy

U-Mo alloy is one of the most promising fuels for the future high performance research and test reactors due to its high uranium loading density and stable irradiation behavior. However, a major concern to its qualification is the fuel swelling at high fission density due to the formation of large fission-gas bubbles. The fission-induced recrystallization further expedites the formation and growth of gas bubbles. So far, the exact mechanism of recrystallization is still unclear. One possible driving force for recrystallization is the production of point defects and interstitial loops due to irradiation. Following this, we developed a multi-scale model by integrating the rate-theory and phase-field models to study microstructural evolutions in irradiated U-Mo alloy, i.e., fission-induced gas bubble evolution and recrystallization. Density function theory (DFT) calculations are utilized to predict the defect formation energies, diffusivities of defects, the interfacial energy of gas bubble, and the elastic constants of U-Mo alloy, etc. The dislocation density evolution is predicted by the rate-theory developed by Jeff. The grain subdivision occurs once the dislocation density is above a critical value. The grain growth coupled with gas bubbles evolution is modeled using a multi-phase phase-field model. The effects of fission rate and initial grain microstructure on the recrystallization process are systematically investigated. The simulated dislocation density, sub-grain size distribution, and volume fraction of the recrystallization grains under different fission density are comparable with experimental data. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cracking behavior and microstructure of austenitic stainless steels and alloy 690 irradiated in BOR-60 reactor, phase I.

Cracking behavior of stainless steels specimens irradiated in the BOR-60 at about 320 C is studied. The primary objective of this research is to improve the mechanistic understanding of irradiation-assisted stress corrosion cracking (IASCC) of core internal components under conditions relevant to pressurized water reactors. The current report covers several baseline tests in air, a comparison study in high-dissolved-oxygen environment, and TEM characterization of irradiation defect structure. Slow strain rate tensile (SSRT) tests were conducted in air and in high-dissolved-oxygen (DO) water with selected 5- and 10-dpa specimens. The results in high-DO water were compared with those from earlier tests with identical materials irradiated in the Halden reactor to a similar dose. The SSRT tests produced similar results among different materials irradiated in the Halden and BOR-60 reactors. However, the post-irradiation strength for the BOR-60 specimens was consistently lower than that of the corresponding Halden specimens. The elongation of the BOR-60 specimens was also greater than that of their Halden specimens. Intergranular cracking in high-DO water was consistent for most of the tested materials in the Halden and BOR-60 irradiations. Nonetheless, the BOR-60 irradiation was somewhat less effective in stimulating IG fracture among the tested materials. Microstructural characterization was also carried out using transmission electron microscopy on selected BOR-60 specimens irradiated to {approx}25 dpa. No voids were observed in irradiated austenitic stainless steels and cast stainless steels, while a few voids were found in base and grain-boundary-engineered Alloy 690. All the irradiated microstructures were dominated by a high density of Frank loops, which varied in mean size and density for different alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High-velocity projectile impact induced 9R phase in ultrafine-grained aluminium

Aluminium typically deforms via full dislocations due to its high stacking fault energy. Twinning in aluminium, although difficult, may occur at low temperature and high strain rate. However, the 9R phase rarely occurs in aluminium simply because of its giant stacking fault energy. Here, by using a laser-induced projectile impact testing technique, we discover a deformation-induced 9R phase with tens of nm in width in ultrafine-grained aluminium with an average grain size of 140 nm, as confirmed by extensive post-impact microscopy analyses. The stability of the 9R phase is related to the existence of sessile Frank loops. Molecular dynamics simulations reveal the formation mechanisms of the 9R phase in aluminium. This study sheds lights on a deformation mechanism in metals with high stacking fault energies.

42 ENGINEERING↗

The importance of properties in modeling

Casting and welding of superalloys, stainless steel and titanium alloys are processes which can be improved through modeling of heat flow, fluid flow, residual stress development, and microstructural evolution. These simulations require inputs of thermophysical data, some of which involves the partially or totally liquid state. In particular, these processes involve melting, flow in the liquid, and solidification. Modeling of such processes can lead to an improved understanding of defects such as shrinkage, inclusions, cracks, incomplete filling (or penetration), macrosegregation, improper grain structure, and deviations from dimensional specifications. Effective modeling can shorten process development time and improve quality. An approach to these problems is to develop efficient models; validate through correlations with thermal, distortion, and microstructural data; run parametric studies; extract knowledge based rules; and apply to adaptive closed loop control systems. With the appropriate pre- and post-processing, such analyses can be made 'user friendly'. This would include graphical user interfaces as well as realistic images and color maps. In such form, these models can be used for sensitivity analyses, which are useful in defining appropriate sensors and in the development of control strategies. Such modeling can be done at several levels, e.g., the MARO level, modeling large scale phenomena such as heat and fluid flow or material deformation; the MICRO level, modeling the development of dendrites, grains or precipitates; or at the NANO level, modeling point defects, dislocations, stacking faults, etc. There are many computational issues associated with these simulations, e.g. computational efficiency and accuracy. In addition, there are many materials issues, not the least of which is the availability of accurate high temperature thermophysical data for complex alloys. This would include latent heat of fusion, temperature dependent heat capacity and thermal conductivity (for liquid and solid), viscosity, surface tension, thermal expansion, mechanical properties, etc. Preliminary data is frequently gathered from the literature; however, this is often not available for modern alloys. If additional data are required, measurements can be used; however, these are costly, time consuming and can be erroneous due to a lack of testing standards or impure materials. Microstructural predictors can be extracted from thermal information, e.g. cooling rate and thermal gradient; the prediction of microstructure is dependent on solidus and liquidus temperature, mushy zone permeability, the solidification curve, volume changes, phase transformations, alloying effects (such as surface tension or viscosity), mold/metal reactions, metal/environment reactions, etc. Defect maps may be needed to predict the onset of shrinkage, hot cracking or 'freckling'. Constants may be needed for stress relaxation, dendrite coarsening, vaporization, etc. Visualization was used as a tool to better comprehend complex data sets associated with the analysis of directional solidification (including crystal growth) and welding. Examples include not only isotherms, but also cooling rate, growth rate and thermal gradient. The latter two are not single valued scalars, but rather time and space dependent vector fields. Efficient models were developed for both casting and welding to predict heat flow and the relationship to dendrite and grain growth. These codes include many of the non-linear effects, e.g. radiation, which dominate these processes. The home-built FDM code(s) were designed to be useful not only to the scientist, but also to the process engineer. Special output can be requested to compare directly to experimental data. Visualization procedures were developed to visualize critical results, e.g. fusion zone width at the surface opposite that where the arc is applied ('penetration'). Both elaborate and simplified distortion analyses were carried out. It is clear that extensive mechanical property data are critical in order to accurately predict residual stress patterns. A scheme is currently being developed to integrate these modeling tools into a set of control algorithms; however, the success of this approach is critically dependent on the availability of accurate high temperature thermophysical data.

Giamei, A. F.↗

Void Swelling and Microstructure of Austenitic Stainless Steels Irradiated in the BOR - 60 Reactor

As nuclear power plants age and neutron fluence increases, detrimental effects resulting from radiation damage have become an increasingly important issue for the operational safety and structural integrity of core internal components. In this study, irradiated specimens of reactor core internal components were characterized by transmission electron microscopy. The specimens had been irradiated to 5.5-45 dpa in the BOR-60 reactor at a dose rate close to 10 -6 dpa/s and temperature of about 320°C. No voids were observed in the austenitic stainless steels and nickel alloys at all doses. Despite the possibility that fine voids below the TEM resolution limit may be present, it was clear that void swelling was insignificant in all examined alloys up to 45 dpa. Irradiated microstructures of the studied alloys were dominated by a high density of Frank loops. The mean size and density of the Frank loops varied from one material to another, but saturated with increasing dose above ~10 dpa. While no irradiation-induced precipitations were present below 24.5 dpa, fine precipitates were evident in several alloys at 45 dpa.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Pre-Irradiation Comparison of W-Based Alloys for the PHENIX Campaign: Microstructure, Composition, and Mechanical Properties

Tungsten is the material of choice as the plasma-facing material in future plasma-burning fusion reactors. During operation, plasma-facing materials will be simultaneously exposed to 14-MeV neutrons, low-energy D/He particles, and high heat loads. Neutron irradiation of tungsten results in bulk material damage, including knock-on damage causing loops and voids, and transmutation reactions leading to the transmutation of tungsten to rhenium and osmium. Under irradiation to high dose, Re and Os atoms can amalgamate into precipitates that drastically alter the material properties, noticeably increasing the hardness. However, the early-stage development of Re and Os precipitates under a fast neutron spectrum has not been investigated.In this work, the microstructure and hardening behavior of W-Re alloys containing 0 to 2.2 wt% Re, TiC-doped W, and powder-injection-molded W are investigated prior to neutron irradiation at 500ºC and 800ºC to ~0.1 displacement per atom in the High Flux Isotope Reactor (HFIR) to establish a baseline understanding of the starting microstructures.Transmission electron microscopy analysis indicates a dislocation-heavy microstructure, and scanning transmission electron microscopy–energy dispersive spectroscopy shows no spatial segregation of Re and W. Similarly, surface compositional studies performed with electron backscatter diffraction and X-ray photoelectron spectroscopy showed no presence of Re, indicating the Re did not segregate or form new phases during fabrication. Here, the alloys in their as-fabricated state showed no Re segregation or second-phase development, with no significant differences between their microstructures and Vickers hardness values.

36 MATERIALS SCIENCE↗

Sensitivity of polycrystal plasticity to slip system kinematic hardening laws for Al 7075-T6

The prediction of formation and early growth of microstructurally small fatigue cracks requires use of constitutive models that accurately estimate local states of stress, strain, and cyclic plastic strain. However, few research efforts have attempted to systematically consider the sensitivity of overall cyclic stress-strain hysteresis and higher order mean stress relaxation and plastic strain ratcheting responses introduced by the slip system back-stress formulation in crystal plasticity, even for face centered cubic (FCC) crystal systems. This paper explores the performance of two slip system level kinematic hardening models using a finite element crystal plasticity implementation as a User Material Subroutine (UMAT) within ABAQUS, with fully implicit numerical integration. The two kinematic hardening formulations aim to reproduce the cyclic deformation of polycrystalline Al 7075-T6 in terms of both macroscopic cyclic stress-strain hysteresis loop shape, as well as ratcheting and mean stress relaxation under strain- or stress-controlled loading with mean strain or stress, respectively. The first formulation is an Armstrong-Frederick type hardening-dynamic recovery law for evolution of the back stress. This approach is capable of reproducing observed deformation under completely reversed uniaxial loading conditions, but overpredicts the rate of cyclic ratcheting and associated mean stress relaxation. The second formulation corresponds to a multiple back stress Ohno-Wang type hardening law with nonlinear dynamic recovery. The adoption of this back stress evolution law greatly improves the capability to model experimental results for polycrystalline specimens subjected to cycling with mean stress or strain. As a result, the relation of such nonlinear dynamic recovery effects are related to slip system interactions with dislocation substructures.

36 MATERIALS SCIENCE↗

The Influence of Neutron Irradiation in FFTF on the Microstructural and Microchemical Development of Mo-41Re at 470-730ºC

Specimens of Mo-41 wt% Re irradiated in the Fast Flux Test Facility (FFTF) experience significant and non-monotonic changes in density that arise first from radiation-induced segregation, leading to non-equilibrium phase separation, and second by progressive transmutation of Re to Os. As a consequence the density of Mo-41Re initially decreases and then increases thereafter. Beginning as a single-phase solid solution of Re and Mo, irradiation of Mo-41 wt% Re over a range of temperatures (470-730ºC) to 28-96 dpa produces a high density of thin platelets of a hexagonal close-packed phase identified as a solid solution of Re, Os and possibly a small amount of Mo. These hcp precipitates are thought to form in the alloy matrix as a consequence of strong radiation-induced segregation to Frank loops. Grain boundaries also segregate Re to form the hcp phase, but the precipitates are much bigger and more equiaxed in shape. Although not formed at lower dose, continued irradiation at 730º C leads to the co-formation of late-forming Chi–phase, an equilibrium phase that then competes with the preexisting hcp phase for rhenium.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Reverse martensitic transformation on the corrosion behavior of a 2304 lean duplex stainless steel

This study investigates the influence of the reverse martensitic transformation on the corrosion behavior of 2304 lean duplex stainless steel (LDSS) at low temperatures (400–600°C). The steel underwent cold rolling, followed by isochronal annealing for 0.5 h. Phase transformations and microstructures were analyzed using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Corrosion resistance was evaluated using a syringe cell with cyclic potentiodynamic polarization in 0.6 M NaCl solution and double-loop electrochemical potentiokinetic reactivation in 0.5 M H 2 SO 4 + 0.001 M KSCN solution. A bimodal breakdown potential behavior, associated with either pitting or transpassivity, was observed in the as-received (AR) and samples annealed at 400°C. Pitting in the AR sample was associated with Al–Mg–Si–Ca–O inclusions, while pitting on the samples annealed at 400°C was linked to local reduced passive film resistance. Severe cold rolling enhanced the pitting resistance of 2304 LDSS. Selective electrochemical etching revealed preferential corrosion at phase interfaces and within the austenite phase. Additionally, annealing at 500°C to 600°C led to a marked decrease in pitting resistance and increased sensitization. Electron backscatter diffraction analysis of the corroded pits in the annealed specimens indicated that pits tend to nucleate and grow in α'-martensite/austenite regions. Furthermore, the nanostructure formed during low-temperature reversion, characterized by dislocation-cell martensite with high dislocation density and stacking faults, may adversely affect corrosion resistance due to heterogeneities associated with alloying element redistribution.

36 MATERIALS SCIENCE↗

Energy Frontier Research Center Center for Materials Science of Nuclear Fuels

Scientific Successes • The first phonon density of states (PDOS) measurements for UO2 to include anharmonicity were obtained using time-of-flight inelastic neutron scattering at the Spallation Neutron Source (SNS), and an innovative, experimental-based anharmonic smoothing technique has enabled quantitative benchmarking of ab initio PDOS simulations. • Direct comparison between anharmonicity-smoothed ab initio PDOS simulations for UO2 and experimental measurements has demonstrated the need for improved understanding of UO2 at the level of phonon dispersion, and, further, that advanced lattice dynamics simulations including finite temperatures approaches will be required for handling this strongly correlated nuclear fuel. • PDOS measurements performed on polycrystalline samples have identified the phonon branches and energy ranges most highly impacted by fission-product and hyper-stoichiometry lattice defects in UO2. These measurements have revealed the broad-spectrum impact of oxygen hyper-stoichiometry on thermal transport. The reduction in thermal conductivity caused by hyper-stoichiometry is many times stronger than that caused by substitutional fission-product impurities. • Laser-based thermo-reflectance measurements on UO2 samples irradiated with light (i.e. He) ions to introduce point defects have been coupled with MD simulations and lattice parameter measurements to determine the role of uranium and oxygen point defects in reducing thermal conductivity. • A rigorous perturbation theory treatment of phonon lifetimes in UO2 based on a 3D discretization of the Brillouin zone coupled with experimentally measured phonon dispersion has been implemented that produces improved predictions of the temperature dependent thermal conductivity. • Atom probe investigations of the influence of grain boundary structure on the segregation behavior of Kr in UO2 have shown that smaller amounts of Kr are present at low angle grain boundaries than at large angle grain boundaries due to the more dense dislocation arrays associated with large angle boundaries; this observation has potentially important ramifications for thermal transport in the high burn-up rim region of light water reactor fuel. • A variable charge interatomic potential has been developed that not only provides an accurate representation of the fluorite UO2 phase, it is further capable of describing continuous stoichiometry changes from UO2 to hyper-stoichiometric UO2+x, to U4O9 and U3O7, and possibly to orthorhombic U3O8. This is the first potential that features many-body effects in all possible interactions (U-U, U-O and O-O) combined with the variable charge. • A theoretical proof has been formulated showing that it is necessary to use the so-called model C phase field approach, consisting of Cahn-Hilliard and Allen-Cahn equations, to describe void evolution in irradiated materials. This work resolved a longstanding literature controversy regarding how to model voids at the mesoscale. • A novel cluster dynamics model has been developed for the nucleation of voids and loops in UO2 under irradiation. This model is important in understanding the defect state of UO2 after irradiation and, more importantly, reveals off-stoichiometric states of irradiated UO2 that are critical for understanding the impact of irradiation on thermal transport. Personnel Successes

36 MATERIALS SCIENCE↗

Report on Sodium Compatibility of Advanced Structural Materials

This report provides an update on the evaluation of sodium structural materials. The report is a deliverable (level 3) in FY11 (M3A11AN04030403), under the Work Package A-11AN040304, “Sodium Compatibility of Advanced Structural Materials” performed by Argonne National Laboratory (ANL), as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing corrosion and tensile data from the standpoint of sodium compatibility of advanced structural alloys. The scope of work involves exposure of advanced structural alloys such as G92, mod.9Cr-1Mo (G91) ferritic-martensitic steels and HT-UPS austenitic stainless steels to a flowing sodium environment with controlled impurity concentrations. The exposed specimens are analyzed for their corrosion performance, microstructural changes, and tensile behavior. Previous reports examined the thermodynamic and kinetic factors involved in the design, fabrication, and construction of a forced convection sodium loop for sodium compatibility studies of advanced materials. This report presents the results on corrosion performance, microstructure, and tensile properties of advanced ferritic-martensitic and austenitic alloys exposed to liquid sodium at 550°C for up to 2700 h and at 650°C for up to 5064 h in the forced convection sodium loop. The oxygen content of sodium was controlled by the cold-trapping method to achieve ~1 wppm oxygen level. Four alloys were examined, G92 in the normalized and tempered condition (H1 G92), G92 in the cold-rolled condition (H2 G92), G91 in the normalized and tempered condition, and hot-rolled HT-UPS. G91 was included as a reference to compare with advanced alloy, G92. It was found that all four alloys showed weight loss after sodium exposures at 550 and 650°C. The weight loss of the four alloys was comparable after sodium exposures at 550°C; the weight loss of ferritic-martensitic steels, G92 and G91 is more significant than that of austenitic stainless steel, HT-UPS after sodium exposures at 650°C. Sodium exposures up to 2700 h at 550°C had no significant influence on tensile properties, while sodium exposures up to 5064 h at 650°C dramatically lowered the tensile strengths of the four alloys. The ultimate tensile strength of H1 G92, H2 G92, and G91 ferritic-martensitic steels was reduced to as much as nearly half of its initial value after sodium exposures at 650°C. Though the uniform elongation was recovered to some extent, these three ferritic-martensitic steels showed considerable strain softening after sodium exposures. The yield stress of HT-UPS austenitic stainless steel increased, the ultimate tensile strength decreased, and the total elongation was reduced after sodium exposures at 650°C. The dynamic strain aging effect observed in the as-received HT-UPS specimens became less pronounced after sodium exposures at 650°C. Microstructural characterization of sodium-exposed specimens showed no appreciable surface deterioration or grain structure changes under an optical microscope, except for the H2 G92 steel, in which the martensite structure transformed to large grain ferrite after sodium exposures at 650°C. TEM observations of the sodium-exposed H2 G92 steel showed significant recrystallization after sodium exposure for 2700 h at 550°C, and transformation of martensite to ferrite and high density of precipitates in nearly dislocation-free matrix after sodium exposures at 650°C. Further microstructural analysis and evaluation of decarburization/carburization behavior is needed to understand the dramatic changes in the tensile strengths of advanced ferritic-martensitic and austenitic steels after sodium exposures at 650°C.

36 MATERIALS SCIENCE↗