Search NASA⌕ Search

SEARCH · Search NASA

Results for “hardware testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Correlation of Full-Scale Isolated Proprotor Performance and Loads

A full-scale isolated proprotor test was recently conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center. The test article was a 3-bladed research rotor derived from the right-hand rotor of the AW609. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. This paper presents correlations between data and predictions of rotor performance and blade moments using the newly acquired test data and the comprehensive analysis CAMRAD II. The operational conditions covered in this analytical study are: hover (actually, low speed vertical climb), cruise (airplane mode), conversion, and helicopter mode. Mean and 1/2 peak-to-peak quantities (hpp) are correlated; time-history correlation for the helicopter condition is also included. The correlation is reasonable to good. Also, the hover calculations turned out to be useful in providing reality checks on the test hardware such as: a) the functioning of the blade strain gages and b) calibration of the measurement of the collective pitch hardware. The time-history correlation shows that, compared to the rolled-up wake model, the multiple-trailer wake model improves the correlation slightly; the longitudinal cyclic correlation is reasonable but the lateral cyclic correlation is not good, and the collective is predicted well by the rolled-up wake model; the flap moment correlation is reasonable; the pitch link load and lag moment are underpredicted; and the torsion moment correlation is poor and needs further study.

Kottapalli, Sesi↗

Risk Reduction for the System Design of an Enhanced MMRTG

Engineering of an enhanced Multi-Mission Radioisotope Thermoelectric Generator (eMMRTG) began 3 years ago with agreement between the U.S. National Aeronautics and Space Administration (NASA) and the U.S. Department of Energy (DOE). The Jet Propulsion Laboratory is leading the transfer of skutterudite thermoelectric couple technology to industry and leading the systems engineering of the proposed eMMRTG. Should NASA fund the flight development of an eMMRTG, the DOE would lead the flight system development. The analytical models and design of the MMRTG have been enhanced to use skutterudite couples developed at Jet Propulsion Laboratory over the last two decades. This required a thorough evaluation of the MMRTG design, and concurrent engineering of an enhanced MMRTG to shed light on potential design issues or risks. At the end of the U.S. fiscal year (FY) 2015, a complete catalog of risks was produced. Tests, hardware development, and analyses have now been put in place to mitigate those risks to acceptable levels. Few risks can ever be truly eliminated unless a design is modified to eliminate specific risks and not introduce more severe risks. The design imperative for the eMMRTG is to change only a few MMRTG features; therefore, risks can largely only be mitigated, not eliminated, through design changes. However, many risks can be effectively - though not totally - eliminated without design changes. This paper briefly describes some of the documented risks and mitigations or reduction approaches to be applied in the coming 3 years, on the way to completing the eMMRTG concept.

eMMRTG↗

Planetary Water Recycling Systems Trade Study

Long-term planetary space missions present new and unique challenges in life-support systems. Water constitutes the majority of the mass required to sustain human life in space and it follows that efficient water recycling has the potential to lower mission costs. The effect of partial gravity in planetary missions mean that terrestrial systems could be applicable. This trade study evaluates terrestrial and NASA developed water recycling technologies on the basis of applicability as a planetary base water recycling systems. Various bioreactors, membrane reactors, filtration, and district water reclamation systems are investigated and rated based on several standardized parameters. A customer-oriented Quality Function Deployment (QFD) is utilized to analyze the ratings of the technologies for the tasks required. The trade study aims to rank the various systems based on their Equivalent System Mass (ESM), Technology Readiness Level (TRL), scalability, crew time, and overall logistics requirements, among others. The results of the study can serve as a basis for future inquiries and studies by NASA and other interested parties. The results of this study provide a down selection from 24 systems to 5 systems that trade very close to each other. The results provide a context and justification for a future comparative hardware test program to determine which of these systems offer the best solution.

Flynn, Michael↗

Going to Extremes NEEMO Case Study

In human space flight, crew preparation is paramount. NASA employs various tools in order to best prepare its crews; simulation and simulators, training for specific extravehicular activity (EVA) tasks in its Neutral Buoyancy Laboratory, and survival training. Apollo astronauts participated in desert wilderness survival to hone their skills. NASA has a long history of using terrestrial based activities as space flight analogs to advance science, test hardware and techniques, and develop crew leadership skills and team solidarity

Lessons Learned↗

Mass Mitigation in Structural Designs Via Dynamic Properties

Mass Mitigation in Structural Designs Via Dynamic Properties The reported efforts are focused on mitigating unnecessary mass in aerospace hardware via leveraging dynamic strength of materials and the frequency dependency of strain. Analytically predicted dynamic responses of structures are often applied as static loads in stress analyses that ultimately dictate the weight of a structural design. Assuming a dynamic response is a static load and then comparing resulting stress predictions to a static strength property is a long-standing engineering practice. Doing so is known to be, or is assumed to be, conservative. However, little indication of the order of magnitude of embedded conservatism has been identified. NASA/MSFC efforts in 2011, 2019, 2020, and now in 2021 have begun to qualitatively show the order of magnitude of that conservatism. A quick turnaround engineering method is pursued to leverage the subject facets of physics for the purpose of decreasing the weight of flight hardware. Tests performed using simple beams and significant observations are described.

mass mitigation↗

Overview of NASA's Adaptive Structures Program

The paper reviews NASA's research program, flight experiments, and flight application related to Adaptive Structures. Emphasis is placed on results from both experimental and flight hardware test programs that helps validate its theoretical performance. The paper includes the role of Adaptive Structures to meet NASA's current and future technology and programmatic needs.

adaptive↗

Modeling and Analysis of Stirling Power Convertors

Modeling and Analysis of Stirling Power Convertors Luis A. Rodriguez1 Steven M. Geng, Terry V. Reid, Scott D. Wilson NASA Glenn Research Center, Cleveland, OH, 44135, USA NASA Glenn’s Thermal Energy Conversion Branch is supporting the development of the next generation free-piston Stirling power convertors. American Superconductor (AMSC) and Sunpower Inc. are the two firms under contract to develop the Flexure Isotope Stirling Convertor (FISC) and the Sunpower Robust Stirling Convertor (SRSC), respectively. To comprehend and forecast convertor performance, Sage, ANSYS® Maxwell, and ANSYS® Fluent were used to model the Stirling thermodynamic cycle, alternator electromagnetics, and piston and displacer dynamics. I. Introduction Stirling convertors are being developed by NASA as a potential steady source of electrical power for NASA’s future scientific space missions. Currently, NASA Glenn Research Center has two corporations under contract, American Superconductor (AMSC) and Sunpower Inc., for the development of the next generation of free-piston Stirling convertors for dynamic radioisotope power systems. AMSC is developing the Flexure Isotope Stirling Convertor (FISC), which uses flexures to prevent side motion and rubbing of the piston. Similarly, Sunpower Inc, is developing the Sunpower Robust Stirling Convertor (SRSC). The SRSC uses gas bearings to prevent radial contact of the moving piston. As convertor development continues, it is increasingly important to understand and predict the interactions of components in the system, how they respond to one another, and how they perform as a response to changes in operating conditions. A suitable and enlightening way to demonstrate and foresee these interactions is with the use of accurate modeling software. Sage, ANSYS® Maxwell, and ANSYS® Fluent are the current modeling tools used by NASA to analytically determine convertor performance. Sage is a one-dimensional object-oriented commercial software package used for modeling and optimizing Stirling convertors for Dynamic Radioisotope Power Systems (DRPS) and it is one of the most accurate Stirling convertor codes in use by NASA. This code is the successor to GLIMPS (Globally-Implicit Stirling Cycle Simulation) and GLOP (GLIMPS Optimization) software created by Gedeon Associates [1]. Model input parameters are typically material/gas type, component physical dimensions, temperatures, frequency, charge pressure, and number of time/space nodes. Sage is used to model both the FISC’s and SRSC’s Stirling cycle thermodynamics and piston/displacer dynamics. Performance maps were created and analyzed for both power systems to better understand the relationship between the following conditions: cold-end temperature, hot-end temperature, piston/displacer amplitudes, pressure drop, and thermal input power. The synergy between these conditions will help determine parameter sensitivity. ANSYS® Maxwell was used to create a three-dimensional (3-D) axisymmetric model for both FISC and SRSC alternators. The significant physical components included in each model are the magnets, magnet carrier, outer/inner laminations, and the coil. Inputs to the model are piston amplitude, piston frequency, alternator load, coil resistance, tuning capacitance, and specific material properties. The alternator models calculate terminal voltage, current, piston/current phase, voltage/current phase, coil inductance, terminal power and efficiency. The RI2 losses, core (hysteresis and eddy) losses, and magnet/can eddy losses are also a part of the final results. ANSYS® Fluent is used to build 3-D computational fluid dynamic (CFD) models to examine the Stirling cycle thermodynamics for both the FISC and SRSC systems. Three-dimensional Computer Aided Design (CAD) models were used to create the physical components of each convertor. Steady-state simulations were conducted for hardware testing, prediction of environmental losses during testing, and generation of radiation look-up tables. The model inputs to the aforementioned analysis are the material properties and boundary thermal conditions. The steady-state model calculates temperature and heat flow distributions. Transient 3-D calculations were also part of the CFD analysis. In this study a physically reduced version of the FISC is used to obtain a prediction of available engine power. For the gas bearing SRSC, the transient effort is used to obtain a prediction of bearing pad performance and its sensitivity to micro-channel geometric variation. The model inputs to the transient simulations are the piston amplitude, displacer amplitude, frequency, displacer/piston phase angle, dynamic deforming CFD grid, temperature boundary conditions, and user defined files describing motion profile of piston/displacer. The results of the model are temperature distributions, heat distributions, and PV power produced at pre-determined conditions.

Luis A Rodriguez↗

Mass Mitigation in Structural Designs Via Dynamic Properties

The efforts reported here are focused on mitigating unnecessary mass in aerospace hardware. The approach to remove this undesired mass from the design is to leverage both the dynamic strength of materials and the frequency dependency of strain. Analytically predicted dynamic responses of structures are often applied as static loads in stress analyses that ultimately dictate the weight of a structural design. Assuming a dynamic response is a static load and then comparing resulting stress predictions to a static strength property is a long-standing engineering practice. Doing so is known to be, or is assumed to be, conservative. However, little indication of the order of magnitude of embedded conservatism has been identified. NASA/MSFC efforts in 2011, 2019, 2020, and now in 2021 have begun to qualitatively show the order of magnitude of that conservatism. A quick turnaround engineering method is pursued to leverage the subject facets of physics for the purpose of decreasing the weight of flight hardware. Tests performed using simple beams and significant observations are described.

conservative design loads↗

Completing the development of the 12.5 kW Hall Effect Rocket with Magnetic Shielding (HERMeS)

The Hall Effect Rocket with Magnetic Shielding (HERMeS) is a 12.5 kW Hall thruster co-developed by NASA Glenn Research Center and the Jet Propulsion Laboratory. HERMeS incorporates magnetic shielding to eliminate discharge channel erosion in order to reach its design lifetime of 50 kh at specific impulses up to 3000 s. The capabilities of the HERMeS thruster technology transferred to Aerojet Rocketdyne under the Advanced Electric Propulsion System (AEPS) program are described. HERMeS hardware testing is now focused at reducing risk and supporting the qualification of the AEPS thruster. These includes a series of progressively longer wear tests, plasma characterization and modeling supporting life qualification, magnetic field optimization, and environmental testing. Initial results from AEPS thruster testing show operation consistent with the HERMeS thrusters and steady-state operation has been achieved at 600 V, 12.5 kW.

Herman, Daniel↗

Overview of NASA's RESOURCE (Resource Exploration and Science of OUR Cosmic Environment) Project

The RESOURCE(Resource Exploration and Science of OUR Cosmic Environment) project is supported by NASA’s SSERVI (Solar System Exploration Research Virtual Institute) and is led by Principal Investigator (PI) Dr. Jennifer L. Heldmann and Deputy PIs Dr. Matthew Deans and Dr. Alexander Sehlke at NASA Ames Research Center. RESOURCE is focused on enabling In Situ Resource Utilization (ISRU) near the sites of robotic and/or human missions to enable sustainable and affordable exploration of the Moon and near-Earth objects (NEOs). This year RESOURCE has supported the development of a summary of the current state of knowledge regarding lunar polar volatiles as well as a comprehensive catalog and analysis of NEOs. RESOURCE is developing advanced mission capabilities to enable rapid, collaborative operations for lunar resource exploration missions. Hardware testing has been conducted to evaluate potential contaminants released during lunar polar regolith heating. Volatiles and particulates are the two sources of contamination that will affect the requirements of a water cleanup system, and RESOURCE research has identified the requirement for filtration prior to electrolysis for ISRU. RESOURCE also supports development of next-generation planetary drilling systems with integrated instrumentation within the drill. RESOURCE is also deeply committed to sustained efforts to engage educators, students, and broadening participation among under represented groups, and has partnered with Howard University in Washington, DC to foster minoritized students’ interest in STEAMD (science, technology, engineering, arts, math, design) careers through direct and virtual experiences with NASA Subject Matter Experts.

Jennifer L Heldmann↗

Characterizing Fit Factor of a One Size Fits-Most Emergency Mask using Subjects with Smaller Neck Circumferences

The Emergency Mask (EM) is an integral part of fire response on ISS, Orion and Gateway. The EM is a hood type protection respirator sealing around the subject’s neck, with an additional nose cup covering the subject’s oral nasal region. When integrated with a pair of Fire Cartridges (FCs), this system can be used to provide safe breathing air in a post-fire environment. The initial EM was certified as a ‘one size fits most’, however a recent requirements scrub discovered that the neck circumferences of the smallest possible crew population were not included in the initial requirement set. The test described in this paper uses the same slightly modified industry standard respirator test called a ‘Fit Factor’ used to certify the existing EM for larger subjects. Tests were performed on eight test subjects with neck circumference smaller than the initial EM requirement to determine if the current EM provided adequate protection during post-fire scenarios. The test included subjects donning an EM and then performing a number of head movements in a tent filled with approximately 50,000 particles/cm3 of smoke particulate. During these motions, particulate measurements were obtained from within the EM and compared with particulate measurements in the surrounding environment to determine the protection the EM provided in a simulated post-fire environment. This paper provides descriptions of the test hardware, methodology and results, which have provided rationale to design and build an EM to accommodate subjects with smaller necks.

Respirator↗

Artemis Internal Science Team Update: Deployed Payloads

Artemis will reestablish human presence on the Moon and lead to a new era of scientific discovery and exploration. Led by the National Aeronautics and Space Administration (NASA), the Artemis effort includes a collaboration of space agencies and companies from around the world [1]. In support of Artemis, a cross-disciplinary effort of science, engineering, operations, and human factors personnel is currently developing the best methods, facilities, and field locations to test hardware, train astronauts, and evaluate concepts of operations. This abstract, as part of the Artemis Internal Science Team (AIST) [2], provides an update to NASA’s plans for the solicitation, development, and operations of deployed surface payloads. In calendar year 2023, NASA’s Science Mission Directorate will solicit proposals for instruments to be deployed by crew on the surface of the Moon (Fig. 1), beginning with Artemis III [3]. The Artemis III mission will land in the south polar region of the Moon, within 6º of latitude from the south pole, in the vicinity of both persistently illuminated and permanently shadowed areas of the Moon, with potential access to surface-accessible volatile deposits [4]. Several of the proposed landing regions are located among some of the oldest parts of the Moon, and together with the permanently shadowed regions, provide the opportunity to learn about the history of the Moon through previously unexplored lunar regions [5]. Deployed payloads will be a critical part of a notional program that captures the highest-priority science for Artemis III and provides the greatest feedforward to follow-on missions and the build-up to the Artemis Base Camp

R. C. Weber↗

Artemis Internal Science Team Update: Deployed Payloads

Artemis will reestablish human presence on the Moon and lead to a new era of scientific discovery and exploration. Led by the National Aeronautics and Space Administration (NASA), the Artemis effort includes a collaboration of space agencies and companies from around the world. In support of Artemis, a cross-disciplinary effort of science, engineering, operations, and human factors personnel is currently developing the best methods, facilities, and field locations to test hardware, train astronauts, and evaluate concepts of operations. This poster, as part of the Artemis Internal Science Team (AIST), provides an update to NASA’s plans for the solicitation, development, and operations of deployed surface payloads. In calendar year 2023, NASA’s Science Mission Directorate will solicit proposals for instruments to be deployed by crew on the surface of the Moon (Fig. 1), beginning with Artemis III. The Artemis III mission will land in the south polar region of the Moon, within 6º of latitude from the south pole, in the vicinity of both persistently illuminated and permanently shadowed areas of the Moon, with potential access to surface-accessible volatile deposits. Several of the proposed landing regions are located among some of the oldest parts of the Moon, and together with the permanently shadowed regions, provide the opportunity to learn about the history of the Moon through previously unexplored lunar regions. Deployed payloads will be a critical part of a notional program that captures the highest-priority science for Artemis III and provides the greatest feed-forward to follow-on missions and the build-up to the Artemis Base Camp.

R. C. Weber↗

Multi-Angle Imager for Aerosols (MAIA) spectral and radiometric calibration

The Multi-angle Imaging SpectroRadiometer (MISR) was launched as part of NASA’s Terra satellite suite of instruments. Still operational, it makes use of observations from multiple view angles to retrieve aerosol abundance and particle properties. The Multi-Angle Imager for Aerosols (MAIA) instrument improves on this heritage by incorporating polarimetry and an expanded spectral range. Combining these data with surface measurements, the relationship between pollution and human health will be explored. MAIA has just completed camera testing, building on the experience from MISR. Spectral calibration now makes use of a double subtractive monochromator, built with the intent to allow the exit slit output to be uniform in spectral content. For radiometric testing, hardware upgrades have included adding UV lamps to the 1.65 cm (65") integrating sphere, use of a NIST-traceable sphere to establish absolute radiances, and the addition of a UV transfer spectrometer to support characterization of the sphere output from 300 to 2500 nm. During camera build, Newton’s rings were observed in the detector Quantum Efficiency (QE) measurements. This is due to etaloning within the detector itself. Etaloning was also evident in the spectral and radiometric characterizations performed on the completed camera. Spectral metrics, including center wavelength and width, are presented here using a moment’s analysis. This better represents the band properties, particularly in bands where fringing is observed, as compared to a full-width at half-maximum determination. It is believed that the MAIA camera has been carefully characterized, and meet its spectral and radiometric requirements.

Harten, Gerard Van↗

Assurance Equations: A Cost and Criticality Model for Optimizing Quality Assurance Surveillance

The cost of quality vs cost of failure correction has been a long-running topic of discussion within the Aerospace community. It leads directly to concepts of “risk tolerance”, and risk-based decision-making. It would be valuable if there was a way to compute the optimal investment in customer-executed quality assurance activities using defect significance with respect to performance objectives, the activities’ defect detection effectiveness, and the cost-penalty for late discovery of impactful defects. This optimization is particularly of interest to projects whose budget constraints significantly limit their risk management options.The cost to fix defects (i.e., failure correction) escalates as the project matures. There have been studies attempting to determine the relative cost of fixing defects discovered during various phases of a project life cycle with important implications, all of which suggest growth factors are large. The commonly referred to 1:10:100 rule represents a cost multiplier for repair/rework across the Design to Fab to Test hardware development phases. Cost premiums for QA activities also accumulate when they are treated as mandatory (due to schedule drag) or are performed later than their assigned phase.This paper describes the modeling of development phase -dependencies in the conduct of typical customer-executed quality assurance activities. Our initial modeling encompasses:• Distinct phases of the production lifecycle• Multiple kinds of Defects, each with some a-priori likelihood of being present• Each defect’s impact on performance Objectives for a type of hardware• The cost and efficacy of assurance techniques at detecting such Defects• The costs of fixing those Defects detected in a given phase of the production lifecycleThe model captures assurance activities’ abilities to Detect defects. Upon detection it is assumed that the Defect is immediately fixed. Defects that “escape” detection by some activity may thereafter be detected by a later activity, but by then the cost of fixing the Defect may have escalated. Defects are related to the performance Objectives they would detract from, were those Defects to remain present in the operating system.We have constructed and are exploring, a model that relates the importance of hardware system elements to mission objectives, the impact of types of Defects on those hardware types, the cost of customer-executed assurance activities (i.e., supplier controls) and their effectiveness towards reducing an impactful quality escape, and the cost of Defect correction across production phase. We describe the approach taken to select the key model aspects, why they are relevant to our NASA mission, and our efforts to populate it with relevant and contemporary data. We use a notional example to illustrate model design and function.

Plante, Jeannette↗

An Evaluation of the Additional Acoustic Power Needed to Overcome the Effects of a Test-Articles Absorption During Reverberant Chamber Acoustic Testing of Spaceflight Hardware

It is important to realize that some test-articles may have significant sound absorption that may challenge the acoustic power capabilities of a test facility. Therefore, to mitigate this risk of not being able to meet the customers target spectrum, it is prudent to demonstrate early-on an increased acoustic power capability which compensates for this test-article absorption. This paper describes a concise method to reduce this risk when testing aerospace test-articles which have significant absorption. This method was successfully applied during the SpaceX Falcon 9 Payload Fairing acoustic test program at the NASA Glenn Research Center Plum Brook Stations RATF.

sound power↗

An Evaluation of the Additional Acoustic Power Needed to Overcome the Effects of a Test-Article's Absorption During Reverberant Chamber Acoustic Testing of Spaceflight Hardware

The exposure of a customer's aerospace test-article to a simulated acoustic launch environment is typically performed in a reverberant acoustic test chamber. The acoustic pre-test runs that will ensure that the sound pressure levels of this environment can indeed be met by a test facility are normally performed without a test-article dynamic simulator of representative acoustic absorption and size. If an acoustic test facility's available acoustic power capability becomes maximized with the test-article installed during the actual test then the customer's environment requirement may become compromised. In order to understand the risk of not achieving the customer's in-tolerance spectrum requirement with the test-article installed, an acoustic power margin evaluation as a function of frequency may be performed by the test facility. The method for this evaluation of acoustic power will be discussed in this paper. This method was recently applied at the NASA Glenn Research Center Plum Brook Station's Reverberant Acoustic Test Facility for the SpaceX Falcon 9 Payload Fairing acoustic test program.

absorption↗